How to access the computer management?

Similar Questions

• I want to know how to restore the computer to its factory settings, when I bought from a private party and have an administrators access code

  I want to know how to restore the computer to its factory settings, when I bought from a private party and have an administrators access code

  Hello

  What is the brand and model of the computer?

  The best method is to contact the computer manufacturer for help on how to set the computer to its factory settings.

  Hope this information helps.

• How to access the CLI Mode in cisco sf 302 - 08 p 8-port 10/100 Managed switch

  Hello

  Can someone help me on how to access the CLI mode in cisco sf 302 - 08 p 8-port 10/100 Managed switch. I treid the each method they mentioned in the administration guide. I am not able to enter the command debug mode and comand menu after resetting the default password. Once connected, sound directly to guide me to switch main menu.

  Hello FAL, Mark,.

  Thank you for your participation in the community of support to small businesses. My name is Nico Muselle of Cisco Sofia HWC.

  To access the CLI, you must make sure that the version of the firmware on your switch is at least 1.1.0.73 or preferably higher. Then activate telnet or ssh on the switch and opening of these sessions or a console session you will see that you are in CLI mode. You can return to the console to function menu using the menucommand.

  I hope that answers your questions!

  Best regards

  Best regards

  Nico glacier

  Senior Network Engineer - CCNA - CCNA security

• How and when the computer turns off automatically?

  Listen to internet radio, Sys Pref > saving energy on the default setting, wake up and radio program cut.

  This is great... .buth how and when the computer turns off?  When I reopen it wifi comes back, I'm correct when she stops she also turns off wifi?

  Hello allan299,

  Thank you for using communities of Apple Support.

  According to your post, I see that you have any questions on how and when your computer shuts down, and how the WiFi on your Mac is affected. I know it's nice to be able to properly manage what happens when your computer stops and starts in mode 'sleep'. I'm happy to help you find the best resolution.

  You're right, when your computer stops completely it will turn the Wi - Fi. If you enable the wake for network access, Wi - Fi remains lit, and you can access shared resources on your computer, such as printers or iTunes shared playlists even when your computer is in "sleep". Definition of a calendar closing and start on your Mac can also be useful.

  Check out the following resources that will help the set options that control the energy use of your computer, sleep, and wake-up times for your Mac and the calendar from your Mac to turn on or turn off or go to sleep:

  OS X Yosemite: energy saver Preferences

  OS X Yosemite: set sleep and wake up on time for your Mac

  OS X Yosemite: A schedule for your Mac to turn on or turn off or go to sleep

  Best regards.

• Not able to see the contents of the computer management it gices a snap - in error.

  Recently, I had some problems on the computer. So what I did, this is what I do sometimes normally when it is not noticeable.

  Open the windows system event logs just to see if there are some errors arise in there.

  The problem is that, with this time is that I somehow clicked on disk management. I don't have (just woke up) how but when it was still loading so I immediately clicked on where the event log was until I received a notification that did

  Snap broke down, and I think that the FX error message: {b05566ae-fe9c-4363-be05-7a4cbb7cb510}

  My question is:

  Is there something I need to do? Should I be worried because it could have happened because he was still loading disk management? I return to the computer management and it doesn't seem to be showing normally, but I didn't click on anything anyone, just in case.

  As you can probably tell by here, but I know something but certainly not entirely savvy computer especially on Windows

  Thanks in advance!

  You can access the observer of events directly from the command run:
  http://www.Windows-commandline.com/Windows-Event-Viewer-run-command/

  Select Start, run, type eventvwr , and press the ENTER key.

• How to access the info in my iCloud account

  How to access the info in my iCloud account?

  You can access much of the iCloud.com on a computer or through specific applications on your mobile device such as contacts, calendars, iCloud Drive, Photos. What exactly you were looking for and what type of device.

• Lack the profile can not access the Profile Manager, cannot be continued

  Yahoo somehow accessed and changed the settings of my browsers safari and firefox, could not change the settings for search engine default for more than a minute, even remove engine from yahoo wouldn't last a minute, so I deleted firefox, re-uploaded, now my profile is missing...

  I can not access the Profile Manager via the Terminal, I can't do anything, Firefox is not operational at this time and I don't know how to fix it.

  In Mac OS X v10.7 and later versions, the ~/Library folder is a hidden folder.

  • http://KB.mozillazine.org/Show_hidden_files_and_folders#Mac_os_x
  • http://KB.mozillazine.org/Profile_folder_-_Firefox#Mac
  • < User > /users//Library/Application Support/Firefox/profiles.ini

  See also:

  • https://support.Mozilla.org/KB/how-run-Firefox-when-your-profile-missing-or-inacc

• How to access the BIOS on a Pavilion Elite e9237c with mouse and keyboard wireless?

  I have a desktop computer Pavilion Elite e9237 with a wireless keyboard and mouse. I tried to access the BIOS by pressing F10 at startup with no luck, and I can't access any of the other menus for the start-up eiither. I don't have a PS/2 port on my computer, so I can't get a wired keyboard and mouse. Does anyone know how to access the BIOS with this configuration?

  I bought a USB keyboard and he answered in the same way... No bios access. I then studied why it did not work and discovered that it was the way in which he has been connected to the computer. I had initially plugged into a USB hub when he was not working and I moved it directly into a USB port and it works! I plugged my keyboard wireless directly into the USB port and it works too! Thanks for your help... I wouldn't have thought of it if it wasn't for to recommend you the USB keyboard.

• HP laptop - 15-ac121dx: how to access the ram on a 15-ac121dx modules

  I want to upgrade the ram in my HP laptop - 15-ac121dx and maybe the hard drive, but I can't understand how to access the ram. There is no access panel, and unlike some other models, it doesn't have a single lever in the battery bay to remove the cover.

  OK, I realized how down low on the laptop.  After watching some youtube videos I came across another HP laptop computer who had screws under the rubber feet and of course there are also screws under the back of two rubber feet, can't believe I didn't think to look under them.

  To get the background you need to:

  1. Remove all the screws on the bottom.  (Must be 12 total)
  2. Remove the drive from DVD (Yes it does not).
  3. Finally, carefully separate the case around the side.

  After that, you should have full access to the slots of RAM and hard drive.

• How to access the hard drive USB on E3000? Am I missing something?

  I have my router configuration fine to the internet, as well as the media server.  I can't understand how to access the hard drive of my laptop, however.  The manual says to put 192.168.1.1 in the field the address of windows Explorer, but it gives me just the 'Setup' page for the router.

  Am I missing something simple?  I use Windows XP.

  Click on start - go to start > Run/start search and type "\\192.168.1.1" (without the quotes) and press on enter and it should ask the user name and password, the user name and password, use "admin" all lower case, and then click Ok... Now you should be able to see your USB... You must make a right click on it and select "Map network drive" and check the Enable box and below click Finish... It will map the USB on your computer... Once done, you will be able to send and receive data from your computer to the USB...

• Why can't I access the Intel Management Engine BIOS?

  I have a Dell Precision Tower 5810 running Windows 8.1 Pro 64-bit.

  My system has an integrated NIC (Intel 1217-LM Ethernet connection)

  You're supposed to be able to access the Intel Management Engine BIOS by pressing Ctrl-P, when you see the screen that tells you to press Ctrl-P to enter MEBx Setup - but the screen never appears when I reboot everything by attaching masking tape on the F12 key.

  I have reason to believe that DHCP can be sayabled in the BIOS Intel Management Engine & I need to enable because my optical fiber ISP uses dynamic instead of static IP addresses IP addresses.

  MEBx is VPRO no INTEL Management Engine.  If you have an INTEL CTRL P then there will be a white sticker inside the case with a number.

  If it's a 3 MEBx is disabled permanently at the factory.

  http://www.Dell.com/support/article/us/en/19/SLN143077/en

  This label has a number that indicates the management mode that you choose get configuration appropriate for the computer.

  

  There are 3 parts of the software other than BIOS

  Intel Chipset S/W installation utility
  Intel AMT HECI
  Intel AMT GROUND / LMS

  CTRL P is very old in the

  Optiplex_755_Users_Guide_iAMT.PDF

  http://downloads.Dell.com/manuals/all-products/esuprt_desktop/esuprt_optiplex_desktop/OptiPlex-755_user%27s%20Guide%202_en-us.PDF

• How to reset the computer to start the boot minimum troubleshooting.

  I posted this screenshot because I have no idea what can be the maximum size of a question and I thought I have copy paste this but I to Sir's life saw the question so I did this. Additional information that could help. This is my task manager open resource monitor and windows firewall not wanting to tk starts. And I have windows updates where I chose to update (I try to deny each update.) And so far I've checked that I have 482,5 MB of updates of windows that say I should put to date. (apperently 130 important and 10 optional) in addition apperently my computer don't think that I am administrator I do not understand when I'm the only profile on the computer.

  Hello

  In response to the information provided by you, please try to follow the methods and check them off below if this can help,

  Step 1: Scan of Sfc.

  System File Checker is a Windows utility that allows users to find corruptions in Windows system files and restore the damaged files.

  Follow the steps below to perform a scan of the SFC.

  1. press the Windows key + X key.

  2. Select prompt (admin).

  3 type the following command:

  Sfc/scannow

  Step 2: Clean boot.

  Make your systemclean boot State helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  https://support.Microsoft.com/en-us/KB/929135

   

  WARNING: After troubleshooting, refer to the section «How to reset the computer to start normally after a boot minimum troubleshooting»

  Please let us know if the problem is resolved or you need additional assistance.

  Thank you.

• How to access the filters Gallery tab filter on Photoshop CC?  It is gray and unavailable on my screen.

  How to access the filters Gallery tab filter on Photoshop CC?  It is gray and unavailable on my screen.

  Hi Nikon_Guy,

  Could you please let me know the format of the file open in Photoshop?

  Also, what is the mode of the file?

  What version of Photoshop is installed on your computer?

  The operating system you are working on Windows or MAC?

  Kind regards

  Tanuj

• I can't access the computer on which I have installed the software the first time

  Hello, I have purchased a license with VIP account and installed on an iMac. Le computer crashed et I had to change it. I bought a new iMac et installed le creative cloud once again.
  Now I have to Install it on a laptop, but I can not do because the first permit is always connected iMac broken.
  I can not access the computer on which I installed the software the first time.
  
  How can I fix the problem ?
  
  Thank you very much

  Contact Adobe technical support (after the end of the week)

  To the link below, click on the still need help? option in the blue box below and choose the option to chat or by phone...
  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Creative cloud support (all creative cloud customer service problems)
  http://helpx.Adobe.com/x-productkb/global/service-CCM.html ( http://adobe.ly/19llvMN )

• How to access em (Business Manager) MBeans? (JMX)

  How to access em (Business Manager) MBeans? (JMX)

  Via the Java API, you can use the seat of the location API

  http://blog.melvinvdkuijl.nl/2010/02/purge-stale-instances-via-SOA-Suite-11g-Java-API/

  for an example.

  Kind regards

  Melvin