How to activate a port of digital output on a usb9211?

Similar Questions

• How to secure the wiring of digital output BNC-2090

  Hi, I'm working on using the digital output of data acquisition to control the digital DAC input, but I have a problem on how to fix the wiring for the digital output of the DAC. When I plug the cable into the hole, it is vaguely related. Any suggestions on how to fix the wiring are appreciated.

  Thanks in advance!

  It is a spring terminal.

  Try to push in the orange tab with a screwdriver while pushing in the thread.  Release tab to release the wire, and it must grab and hold the wire.  It may be a case involving Orange instead of push.  You should be able to understand.

• How can I improve my 2 digital output signals calendar?

  Hello

  I use a NI DAQ Pad-6015 (usb) with Labview 8.5 and XP to generate 2 digital outputs (high for the first 500ms and 600ms high for the second). The moment didn't need to be very specific, so I use not the 2 outputs hardware clocks. When runing of VI, and measure the length of the outputs with an oscilloscope, I get s 520ms and 640ms. This isn't a problem, but I still want to know, if I'm doing the right thing in my program, or if it is possible to improve it?

  Thanks for your help,

  Kind regards

  Marc

  Hello

  Using all your advice I have exact measure now: only 0 to 4ms delay for signals from ms 500 and 600 using the NI DAQPad-6015.

  PS: Timmer was right regarding the notice of usb. With my previous program when you use a card PCI of 6229, I had only a difference of 10 ms instead of 20 ms with the usb one.

  Thanks for your help,

  Kind regards

  Marc

• How to activate the port HMDI to pay on an Aspire V5 - 571?

  Hi have the Aspire V5-571 and until today could play DVD or movies downloaded from Itunes on my Samsung TV.

  Now, I can't.  I used the HDMI cables down to the Mexico on another tv with no problems, but now I can't even watch a DVD on the tv to the laptop.  I can watch DVDs movies on the laptop, but it does not help us two to watch.

  We tried the Samsung fix by restarting the TV, but it did not work.

  We believe that it is possible the HMDI must be enabled, but does not know where on the computer.  I had to reboot my computer just before we went to the Mexico, but like I said, it worked then... help!

  good answer!

  try to update VGA drivers:

  Intel

  http://global-download.Acer.com/GDFiles/driver/VGA/VGA_Intel_v10.18.10.3304_W81x64_A.zip?acerid=6351...

  NVIDIA

  http://global-download.Acer.com/GDFiles/driver/VGA/VGA_NVIDIA_v9.18.13.2702_W81x64_A.zip?acerid=6351...

• How to activate the CLI GUI

  We have ps6100E EqualLogic. Tried to set up the dedicated management network. Configure and activate 5 port ethernet to the management network. Management network connected to this port to network cable - worked. After that who has decided to return back, but he hurts and off 5 port via Web UI - management network lost. How to activate this port through CLI GUI? Unfortunately, I don't have a reference document CLI for EqualLogic storage and I know not all orders. Help, please.

  
  

• You can activate the port 8080 to access by browser first Infrastructure 2.0?

  By the official document, port 8080 is pre-defintied for access by browser, but it is disabled by default.

  I found a way to activate the port, but I can't find any guide on the cisco site.

  Anyone know how to activate the port 8080?

  Thanks in advance.

  Louis

  HIi Hoi;

  According to the document from cisco: http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1082023

  Configuration of server settings

  The server settings page allows you to enable or disable the TFTP, FTP, HTTP, HTTPS, or compliance department. To activate the server settings or disable:

  Step 1 Choose Administration > the settingsof the system.

  Step 2 In the left sidebar menu, choose the setting on the server.

  Step 3 If you want to change the directories FTP and TFTP or HTTP and HTTPS which had been established when installing ports, enter the port (or port number, and root if necessary) number that you want to change, and then click enable or disable.

  The changes are reflected after a reboot.

  I don't know, but try to change the port 8080 number in the HTTP forward option and save it, then restart.

  I think it will work.

  Concerning

  Remember messages useful rates

• How to activate digital outport on USB6211?

  Hello, I use a usb6211 with DAQmx8.9 and LabVIEW 8.6.1. The lines of dio ports do not appear in the menus of routing functions... How can I activate those ports? Thanks for any advice,

  Vincent

  Simply set the ports in a task. Port 0 is all the entries and port 1 all the outputs. You don't have to move anything. You have to test them in MAX?

• audio output: optical digital output port (no sound!) macbook pro retina 15 mid 2015

  My new recently Mbpr 15 inch has suddenly lost its sound, I went through the process of the toothpick etc but nothing. It worked perfectly fine earlier today, but I put in a mini jack into the headphone port and after to achieve 30 minutes later and taking the cable to THE that I had not his, then I had the red light coming out of the helmet but now its does not come in red and in the sound settings in system preferences its impasse on "optical digital output Port.

  I now have to wait a week to wait until I can get seen at my apple store closet, I coming projects upward and in the middle of deadline and really using this Mbp to work, I literally only had a TI surly less than two months, I shouldn't have any problems. So if anyone knows anything I would appreciate it a lot! I need help to get this resolution as soon as possible! the last post I saw this was in 2006-2012 no new thread on this recently!

  Thank you!

  Jasonwaterz wrote:

  I then had the red light coming out of the helmet but now its does not come in red and in the sound settings in system preferences its impasse on "optical digital output Port.

  Try resetting the NVRAM/PRAM http://support.apple.com/kb/ht1379 memory

• Terca M4: How to activate the external ports, DVI and analog?

  Please can someone please tell how to activate the two external ports. I would use two DVI and analog to the office. Currently if you activate a second screen machine sets up the flat screen and the other the DVI external display. Is this in any way about this?

  See you soon

  Hi Matthew

  As far as I know you can connect an external monitor or a TFT. For this you can use the VGA (15-pin) port or DVI - D video, supported by PortReplicator III (PA3314E).

  Sorry, but I don't understand why you need the two holes at the same time. How many external screens that you want to use? Sorry if I'm missing something but perhaps you can explain your wishes more precisely.

  Good bye

• How to activate the S-video port on a satellite M30X 154?

  Hey does anyone know how to activate the S-video port on your laptop by Satellite SM30X-154?

  If I press the FN + 5 keys the only options I get is LCD and no S-VHS option. My TV is set up for this I have Watch DVD through the cable.

  When I connect the cable to the laptop, nothing happens!
  Help

  Hello

  Sorry, my A100 Tosh has a Geforce 7600, I don't know what is your GA.

  But on mine, I have a NVidia Control Panel, where I can configure dualview,
  normally, which allows me to choose between the builtin LCD and the external monitor (VGA Port).

  When a TV is plugged and not recognized, I can apply recognition there.
  Relative to the opening of the Panel, the TV is also available.

  Maybe I could help you.
  If this isn't the case, note that the settings of windows your TV is not available.
  Try to go to the User Interface of your graphics card...

  Matz

• How to generate the digital output of the variable duty cycle and clock source being contrary?

  I want to generate a digital pulse every front amount of my pulse counters. He must have a variable duty cycle. until now, I've been able to generate a digital output, but I can't change its duty cycle.

  pls tell how I should proceed?

  Thank you in advance...

  
  

• How to quit smoking all the void s vi before resetting digital outputs and then closing

  I have a project that contains a main VI called home screen that calls many different sub vi. I am monitoring for a press of physical button by a digital input with a DAQ Assistant on the main VI and in this case I want my program to abandon all of its VI running and reset all the digital outputs before the closure of Labview. No idea how I would go all this?

  I have attatched the basic model of what I do.

  Joelspider33 wrote:

  The problem is more to do with some of my money that VI running a DAQ Assistant using the same digital lines like the ones I'm wanting to reset and causing it to throw up an error message.

  This is why you must set the DIO AFTER all subVIs are arrested.  And to do this, you must send messages to these subVIs telling them to stop.  If done correctly, it is a very quick process.

• How can I more easily generate a pulse of digital output of finite length?

  Hello

  I need to open and close the two pneumatic valves using a TTL output (without load current or the output power) using a PCI-6280 or PCI-6601. The valves must open almost simultaneously and closing after different amounts of time elapsed (millisecond level timing, maybe 100 microseconds-level timing at worst). My current plan is as follows:

  -Create a task with two digital outputs (type of waveform) and another task with a counter that generates a frequency set by the user (I know I can use the generator frequencies on one of these cards, but I would have preferred a counter - the best selection of frequencies).

  -Wire the output of the counter at the entrance to clock two digital outputs.

  -Output of the meter is digitally triggered by another digital channel which I use to control if the pulse goes out. Through its counter node, it is programmed to be redeclenchables.

  -Two digital waveforms are drafted who have both consist of unique active high pulse (i.e. signals go ' down (for the amount of time user-defined) - low ".")

  -These signals is written to their respective ports and their tasks have started, as is the task of the meter.

  -Whenever the user wants to open taps, digital triggering is sent up and then back to low (this can be done with synchronization software, because it is not exactly when the fire valves). Whenever the user wants the valves open for a different period, different digital waveforms are generated and written in the buffers of the digital output channels.

  My problem is that it looks like a lot of effort for me to go and I wonder if there is a much simpler solution, that I don't know everything. You can program a computer to produce a pulse of finite length? Is there a faster way to program a digital output for that channel?

  Thanks to anyone who responds to their help.

  It is certainly instructive. Thank you.

  The thing is, I have only six total counters to work with and I have a lot of time to do things. To use these solutions, I would need to use 4 or 6 account counters required to my needs.also that I would need to synchronize their departures.

  Overall, I stick to my method for now - less system resources and synchronization can be don by using the same meter of finished output clock and not to use a trigger to all.

  Once again, thank you for your help so far.

• How to measure the digital output of the linear actuator on USB-6009?

  Hello

  I am a new user of Labview and need help to measure a digital input signal.

  I have an actuator Bimba Original line electric with a motor continuous integrated with encoder, drive and the controller. The drive has a programmable digital output that I put as a tachometer output that emits pulses of square wave 100 per turn of the engine. I put the engine to make a total of 56 rev in 22 dry. I want to measure the speed of motor rotation labview real-time and synchronize it with a few other analog input signals. I wired the actuator for the USB-6009 case as shown below.

  

  I opened the test i/o digital USB-6009 Panel and fix all the lines of port 0 as inputs. However, when I click on start and run the actuator, p0.0 led flashes, as indicated below.

  

  Shouldn't the led blink in response to revolutions of engines?

  I want basically to collect the drive pulse signals and convert them in rpm on labview.

  ahsan2 wrote:

  I have it wired correctly?

  It would help if you do not attach the HIGH signal.  Remove the + 5V in the circuit.

• How can I write a digital waveform to the digital output (traditional DAQ)

  Hello

  I use a NI 6023e, PCI, with 8 digital outputs. I generated a digital waveform. How can I write for a specific digital production line now?

  I only have Labview 7, so I can't use DAQmx.

  Thank you very much