How to calculate heart rate in a simple way using visa series

Similar Questions

• the time of acquisition of data - how to calculate the rate of analog output

  I want to calculate an acceptable rate of analog output, one that is taken in charge by material (PCIe6353), without the rate being changed by the VI DAQmx Timing (sample clock). The final objective is to have a rate of analog output that is an integer multiple of the analog input for precise frequency, since the sinusoid AO's amplifiers, which have a ringtone when AO updates occur.

  According to 27R8Q3YF of the knowledge base: how the actual scanning speed is determined when I specify the rate of scanning to My d..., the rate is revised as needed by calculating the rate of clock / asked for advice, divide the result rounded downwards and upwards in the clock of the Board and use the one that is closest to the requested speed.

  If 'Embedded clock' is selected, which is the result "Council clock.  DAQmx sample clock timebase Timing node - SampClk.Timebase.Rate says 100 ms/s. However, for a rate resulting from the update of 2.38095MS / s, the divisor of the time base timing node - "SampClk.TimebaseDiv" gives a value of 42. 42 x 2.38095 M = 99, 999, 990, where it should be 100 ms/s.

  How to calculate an acceptable rate of analog output is supported by the hardware? I have other plates, in addition, a general method would be appreciated.

  I haven't worked all the details yet but noticed a few things that may be relevant.

  Req AI rate isn't a whole ditch 1E8. It is used to determine the rate of the AO.

  There is no check to ensure that the rate of the AO is an integer division.

  It seems that you have the right idea, but the implementation is not yet there.

  Lynn

• How to convert the compound path to simple way barred?

  New animation SVG here and you would appreciate the help.

  I exported an SVG graphic logo to facilitate the animation of lines in the logo. In short, I'm trying to make these lines 'draw' sequentially.

  After you import the SVG object in the browser, I realize the path data to describe complex shapes, rather than a simple path with a vascular accident brain. For example, straight lines appear as a path around the outside edge of the line, a rectangle. See the part of the image below showing the anchor around the edge of the line.

  While I could very well be wrong, it seems that I need to make these lines in the draw of logo is given simple way, with the width of the line determined by a stroke. Does anyone know how I could convert/export what I need to give me what I need?

  Thank you!

  Joseph,

  Simple/no tracks transparent FO, you can do the following:

  1) switch from fill to line in the Toolbox (in you first picture you have completed and no stroke);

  (2) ShiftClick each of the segments of both ends with the direct Selection tool and then tap on delete.

  This will give you two simple traces to the mixture;

  (3) object > mix > blend Options, not specified the value 1, then object > mix > do, then object > mix > Expand, then Ctrl / Cmd + Shift + group to ungroup, and then delete the traces of origin;

  (3) select the new path and him giving the desired weight of stroke (half of the difference in width for traces of origin).

  And Willi comments on using JPEG.

• How to calculate the rate of data transfer if I know that the total number of samples/s?

  I'm looking to set a PXI system for measurement of County at high speed, routes, while that controlled remotely via MXI - 4.  How can I be sure that the controller is capable of rapid data transfer quite seen the number of channels and frequencies of sampling provided?

  I think I figured this out, but maybe someone can save me.  For the task at hand, I will have a PXI-4496 and four PXI - 6143 s all 32768 samples/s sampling.  4496 is 24-bit, and 6143 is 16-bit.  Thus,.

  bits of samples/s/channel x 24 16 channels x 32768/8 = 1 048 576 bytes / s

  +

  32 x 32768 samples/s/channel x 16 bits/8 channels = 2,097152 bytes/sec

  =

  3 145 728 bytes/s, or exactly 3 MB/s.

• How to interface a simple way using LabVIEW 2009 simulink model and SIT?

  Hello

  I finally found a way to use a template simulink with LabVIEW and the Toolbox to SIT, but I'm not satisfied.

  If you have any suggestions, the link of resource that I missed, please do not hesitate to answer

  Note that I do not know much about simulink, so that is my question seems stupid, let me know what

  Software configuration

  OS: Windows (not an RT target)

  LabVIEW 2009

  SIT 2009

  question 1: interfacing the model DLL (mapping considerations) with a driver VI

  We have created a model of DLL by using the 'Workshop in real time' tab in simulink.

  In LabVIEW, launch us the tool 'SIT connection manager' and try to use the DLL with a driver VI by mapping the e/s model for screw/lights orders.

  The fact is that I fail to connect to my controls/indicators VI/o model because they do not appear in the mapping dialog box.

  The simulink single objects that I managed to map are "constant" and "test points" while I need to edit the template simulink itself (example below)

  

  Are in e/s model, not considered as part of the parameters of the model? (this could make sense because the mapping says in fact that it operates on "model parameters")

  Is it possible to link the IO model VI commands/lights?

  Note:

  -the "configure HW i/o mapping" dialog box allows me to map model e/s with e/s HW...

  -The examples also use these "constant" and "test points".

  2nd question: use of direct screw SIT

  I tried to use the DLL directly with the screws SIT (code example below)

  This kind of code works well on another project (target of 8.0/RT LV) but not on the current project (LV 2009/Windows)

  The second stage of the model never ends:

  -0-index of the loop works as expected (model doing its job).

  -index of the loop 1 starts normally, but execution is stuck in the 'SIT scheduler.vi.

  Then I have no choice that to kill LabVIEW ("Reset screws" windows appear if I try to stop/close them).

  

  Is there a reason that I do not see what explains this behavior?

  Thanks for reading.

  Any help appreciated.

  Kind regards

  Hello

  I spent some time analyzing the VI driver as you suggested.

  Here are my findings.

  Question 1: the SIT connection manager does not pass to the model SW controls/indicators. Only, it allows the user map HW AIs/AOs.

  The only solution I found (to have a SW - for example a shared variable - object that is mapped to an input/output model) is to customize the VI driver that is scripted by the SIT Connection Manager ("_Baserate Loop.vi" in the flat sequence structure named "read code")

  Question 2: after spending some time in the VI driver, it seems that the VI to call right is not 'SIT scheduler.vi' but 'If SIT take model no time' (which uses the other as a Subvi)

  

  My conclusions are correct? If I use the API in the wrong way, please let me know.

  Kind regards

• How to calculate the variable on the target, but use the value on the source?

  Hi ODI gurus!
  
  I use LKM MS SQL for Oracle (bcp-> sqlldr).
  I have a variable which is calculated from tables on the target DB (oracle).
  I would use this calculated value in the filter on the source, but I get error ODI is refreshing to variable on the source database.
  
  It is possible to update value of variable on the target technology and using calculated value on the source technology?
  
  Thanks in advance!

  Step 1. In the variable - > refreshing tab - > select the schema and the application required for the Oracle database, so you when you refresh the variable, you get the desired result (for example, the ex - value 25 or whatever you are looking for)
  step 2. Call this variable in the Source filter, where the table_source. COLUMN = #VARIABLE_NAME
  Step 3. Call the Variable in refreshing mode, call the interface.
  So that when the variable is updated to the value that is passed and the source table to get the value of its filter.

  If you do pretty much the same things, can you please paste the error, query and your filter condition. So that we can guide you accordingly.

• I lost the symbol of heart rate on my Apple Watch.  How can I get it back?

  I lost the symbol of heart rate on my Apple Watch.  How can I get that back?

  Hello

  To check your current heart rate on your watch:

  • Use the look of Pulse: when you view the time on your watch, slide up on the screen, then swipe left / right until you find the look of heartbeat. Swipe down on the screen to exit.
  • Siri to check your heart rate to say: ' Hey Siri, check my heart rate "(press the digital Crown once to exit).

  More information:

  Measure your heart rate with your Apple Watch - Apple Support

• How to put in the front of the watch during swimming to see heart rate

  Received the Watch 2 day and taken for a swim practice in the pool (of course)

  happly to see enough faithfully has towers and gives average heart rate but only AFTER training

  I wanted to 4000 m (and I fact..) but from the exercise the watch when asked for the total calories to burn.

  QUESTION 1: how to set the distance (rather than calories)? At the start of the year?

  While the dial of the watch training appeared when out of the water and gave the number of laps, total distance, total time of exercise and calories burned.

  QUESTION 2: you can change the information presented during the swim to see heart rate? (Rather than the number of Calories predictable)?

  NOTE

  For swimming training, the watch is a bit disappointing, given that in the swimming training, you normally do a few repetitions as 10 x 100 start each 01:30 or 01:45. I normally use the watch of Garmin swimming to take the time (100 m start button and press again on arrival) of the clock, then briefly shows duration of the tour and afte 4 continuous seconds so you can see when you start again (e.g. to 01:45). I hope that there will be a third-party solution soon for Apple Watch 2, while I don't have to swim with two watches...

  Hello

  1. After selecting the length of the pool, slide laterally on the screen to move to a distance goal, which can be set in meters or yards (firmly press the screen to switch between them).

  2. follow the following steps to customize the information displayed by the application of training during your workouts in the pool swimming:

  • On your iPhone, in the application of the watch, go to: Watch My > training > training view.
  • Choose several metrics.
  • Tap pool swim > press on edit (top-right) > select up to 5 parameters, including heart rate (they can be arranged in your order of preference).
  • When you are finished, tap on Done (top right).

  More information:

  Work with your Apple Watch - Apple Support

• Heart rate sensor no longer works, how much it cost to fix?

  I have a watch in stainless steel. The heart rate fell and stopped working. The watch is out of warranty. Someone who has had the same experience can tell me how it is to get it repaired? THX

  Hello

  Costs of off-warranty service for Apple Watch are $329:

  • Apple Watch Service pricing - Apple Support

• How to read the heart rate data recorded by the Apple Watch?

  My wife wears a Apple Watch and suffer from power cuts irregulars. After the last of them, I checked the data through the health app and saw that at the time of the blackout, there seems to be no saved data. A range of heart rate was recorded both before and after the blackout. Can someone explain how the data record? Thank you

  MIchael Gilmore

  This explains the various triggers causing the heart rate measure:

  Measure your heart rate with your Apple Watch - Apple Support

  Here is some additional information:

  Your heart rate. What it means, and where on Apple Watch you will find. -Apple Support

• When I do a race with my Apple Watch I don't have a frequency heart displayon the session screen. When I then sync my activity with my iphone there is also no average heart rate on the completion of my activity. How can I get my heart rate displayed?

  When I do a race with my Apple Watch I don't have a frequency heart displayon the session screen. When I then sync my activity with my iphone there is also no average heart rate on the completion of my activity. How can I get my heart rate displayed?

  Hello

  Mode power saving can be activated.

  To check this, on your iPhone, in the application of the watch, go to: Watch My > Workout - if it is currently enabled, disable power saving Mode.

  (When the power saving Mode is enabled, it disables the sensor of heart rate during workouts running).

• How to calibrate the heart rate monitor?

  How to calibrate the heart rate monitor that shows a too high concentration?

  Hello

  It is not possible to calibrate the heart rate sensor. However, various factors can affect the performance of the detector.

  During training, to optimize the performance of the heart rate sensor, ensure that you wear your watch fits on top of your wrist.

  Apple suggests that consider you the clamping Strip before starting a workout and it loosen again thereafter.

  The sensor is likely to give better results for the workouts that involve rhythmic (for example running) rather than the irregular movements (e.g., tennis). Other problems that can affect the performance of the sensor include the perfusion of the skin and wrist tattoos.

  More information:

  Your heart rate. What it means, and where on Apple Watch you will find. -Apple Support

• Using Apple Watch - how do I constantly monitor my heart rate during exercise

  Using Apple Watch - how do I constantly monitor my heart rate during a workout?

  Your heart rate. What it means, and where on Apple Watch you will find. -Apple Support

  According to this link, it should be available - but I can't find it on my Apple Watch?

  Is there a setting that needs to be enabled on it somewhere? The only place where I can see the heart rate is in the menu looks and there are only a few seconds? and takes awhile to show the heart rate.

  Hello

  When you save a workout using integrated workout app, your heart rate will be measured continuously throughout the workout. During training, you can also choose what primary metric is shown on your dial, with choices including heart rate. At the end of the workout, the results include the heart rate data. Training sessions are also recorded in the implementation of the activity on your iPhone.

  During the workout, to change the main metric indicated on the dial of the watch, slide on the side on this subject. Depending on your type of activity, the choice may include: time, active calories, total calories, heart rate, rhythm, speed and distance.

  More information:

  Use of the workout on your Apple Watch - Apple Support

  Use the activity on your Apple Watch - Apple Support

  Health and fitness data from other sources, iPhone, and Apple Watch are also aggregated within the health on iPhone app. Combined data is reflected in the application of health dashboard, which adjusts the results to avoid any double counting of data from different sources.

  To see Apple Watch heart rate data and other sources (for example a Bluetooth chest monitor strap):

  -On your iPhone, in the application of health (icon has a red heart on a white background), go to: data on health (tab) > Vitals > heart rate.

  Data are displayed in graphical form (this can be added to the application of Health Dashboard by activating the setting here) as well as individual data points (via display all data).

• How can I deactivate heart rate monitor

  I want to register my pace heart health App via the data of my cup of BP... I don't want no other heart rate data.  How can I turn off the monitor watch heart where it generates no data in the application of health on my iPhone?

  Hello

  The health on iPhone app, you can reorganize your data sources, that changes the way that the application gives priority to their data.

  A data source which is placed above the other will have priority on all underlying sources that also contribute to the same type of data. Data are not double counted.

  More information and instructions for changing the order of sources:

  Manage the health data from multiple sources on your iPod touch, iPhone, or Apple Watch - Apple Support

  Also, on your iPhone, in the application of the watch, go to: My Watch (tab) > privacy > Motion & Fitness > heart rate. If you disable this setting, however, it will also disable the sensor for the fitness activity for the purposes of follow-up.

• How to calculate the month on month growth rates in an OBIEE application?

  Hi all
  
  I would like to ask for your help on how to calculate the months on growth rate previous/[(last month-previous month) month * 100%] in a query OBIEE. This report should always be calculated for the last 2 months available.
  
  I have the following query:
  Month0 | Months1. Month2
  Produces a 500 | 100. 200
  Product B 600 | 300. 150
  
  I would like to add month on month column as follows:
  Month0 | Months1. Month2. Month on Month (%)
  Produces a 500 | 100. 200 | + 100.00%
  Product B 600 | 300. 150. -50.00%
  
  I tried to add a calculated item, but it failed because I couldn't find a way to not show the column calculated in percent with 2 decimal places. In addition, I would ideally prefer to have an automatic update but as far as I understand it can be done in the automatically calculated item
  
  I also tried to add a new column to the column area and to filter the results for the last month, then for the previous month and then based on that to calculate the necessary ratio but unfortunately it does not work.
  
  Thank you in advance your advice

  Hello

  The best way to solve this problem is by using the function Ago. With this, you can create a logical column for the previous month. Then you will have 2 columns available with which you can do your calculations.

  If you want to do this with a calculated item (don't know if formatting will work for you), but you can do the more general calculation using $1 for the $2 for the 2 column and 1 column in your calculation. If ($x) columns will change with the columns in your report.

  Concerning