How to check and confirm the Nexus 1000V secondary work if primary goes off
Hello
I installed Nexus 1000V Primarry and secondary on different ESXis
but I have to turn off the primary, how to ensure that the school will be in charge and usually have any disconnection
the module displays them and seem to be ok
any other checks to do before continuing?
Thank you
Use "show system redundancy status. You can also manually failover
The output from the example:
n1000v# show system redundancy status
Redundancy role --------------- administrative: primary operational: primary
Redundancy mode
---------------
administrative: HA
operational: HA
This supervisor (sup-1) ----------------------- Redundancy state: Active Supervisor state: Active Internal state: Active with HA standby
Another supervisor (sup-2)
------------------------ Redundancy state: Standby Supervisor state: HA standby Internal state: HA standby
Tags: VMware
Similar Questions
-
How to check and install the drivers for the card
I wanted to play the game with my HP Compaq 8710p (Windows 7) and said that my video card driver and probably (other drivers noticed yet) are now uninstalled in my
System. Could you please send me
links on how to check the
uninstalled the drivers and how to
Download and install. Thank you
in anticipation of the command prompt
response.Zubyjoe
Your uninstall information
or use Revo Uninstaller
http://www.revouninstaller.com/
New Nvidia driver
FTP://ftp.HP.com/pub/SoftPaq/sp61001-61500/sp61072.exe
Other drivers
-
Lenovo Ideapad z565 - how to check and activate the virtual technology (VT) in BIOS
I tried to use virtualization on my Lenovo Ideapad z565 laptop. The laptop is running only Windows 7 Home premium 64 OEM installed. It's an AMD processor dual core. I tried to get some VMWare images into VMWare workstation running on my laptop. Images VMWare has always seem to crash when you try to start them. I read on various forums that this is probably due to virtualization (VT) 'No' enabled in the BIOS. It's supposed to be set in the "Advanced" section of the BIOS. The problem is that when I check my BIOS (F2), the option of virtualization technology (VT) is not in my BIOS. I have a very limited set of BIOS options. I read that the manufacturers of these machines 'block' the user to access advanced options in the BIOS (for reasons unknown to me). In addition, there is a utility distributed by Microsoft, called the "Hardware Virtualization Detection Tool support" that you can download and run on your computer to check if the hardware support for virtualization (VT) is enabled on your computer. I ran this and it is said that VT 'is' activated on my machine. However, I have seen other users, this tool is known to report false positives... which means it reports that VT is enabled, even if it is not. I have also read that these laptops Lenovo, this hardware virtualization is "off"by default. So I think that's my problem. Material to virtualization is disabled in my BIOS, and I have no way to access to 'permit' or turn it on. Someone out there has any experience with this problem, and how did you work around it? Is there a utility that will allow me to enable hardware virtualization in my BIOS? If so, can you provide me with detailed steps to do this? I would really appreciate it. Thank you.
-
How to check and change the outgoing port number
Charter has changed their settings and I need to set the port to 465. How do I do that?
Scroll down the list of accounts. The last of them is "outgoing (SMTP) server.
Select this option, select your Charter SMTP server, click on change.
-
Following presentation of the material of my iMac
Model Name: iMac G5 Model Identifier: PowerMac8,2 Processor Name: PowerPC G5 (3.0) Processor Speed: 1.8 GHz Number Of CPUs: 1 L2 Cache (per CPU): 512 KB Memory: 1 GB Bus Speed: 600 MHz Boot ROM Version: 5.2.5f1 Serial Number (system): QP52107FSDX Hardware UUID: 00000000-0000-1000-8000-0011243B1A5A
Firefox 3.6.x is the last available from Mozilla for PPC Macs.
http://www.Mozilla.com/en-us/Firefox/all-older.htmlFor older Macs that are not considered supported in versions of Firefox 4 +, try TenFourFox for PowerPC in performance Mac 10.4.11 and 10.5.8.
http://www.floodgap.com/software/tenfourfox/
http://tenfourfox.blogspot.com/
https://code.Google.com/p/tenfourfox/wiki/PluginsNoLongerSupported -
I got an update a few months ago. He had a box to check and uncheck the box if I wanted to install McAfee. I didn't then he I unchecked the box. It install it anyway.
Care to guess how angry I was?
I have a new update today, but I don't WANT installed McAfee AGAIN. I missed the window/page that had the check/uncheck box.
I want to assure you that I do not get McAfee installed again. How do I do that?
I'm glad that I don't work for Adobe but I don't know everything that you are angry customers.
-
How to check latency between the ESX host and SAN
How to check latency between the ESXi host and SAN
Hi friend
Below KB will solve your need:
Under discussion can help you get more insight:
Best values LVAD/cmd (ESXTOP)?
Learn ESXTOP @ latency:
vCenter and Esxtop to storage i/o bottlenecks to avoid
Very detailed blog on ESXTOP:
-
When I start my system the output display poster always your computer have Persist modula order check and solve the Problem.How to solve this problem
Permanently?Hello
What operating system is installed on the computer?
Update video drivers and see if the problem persists.
http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctlyNote: install the drivers on the manufacturer's Web site
Hope this information helps. -
We are trying to install a PCIe 6251 DAQ card in a box of Gentoo 64 bit running Linux kernel 2.6.28 - gentoo-r5 4.3.2 - gcc and glibc - 2.8. We have installed RPM utilities to manage the installation. The current problem is that we are not able to compile and install the kernel modules: nidmxfk, nimsdrk, nimstsk and nipxirmk. Here's a summary of what we have done so far, and to what extent we got.
First of all, we have changed the configuration of the kernel that we could export the init_mm unused symbol by changing the configuration option of the CONFIG_UNUSED_SYMBOLS = o kernel and recompile the kernel. Then we installed LabView 8.6.1. Then we ran the nation 1.9 installer who has installed the source code in vain on the compilation. To resolve this problem, we have changed the function of pte_offset to pte_offset_kernel by editing the file/usr/local/natinst/nation/configures following the instructions here:
http://decibel.NI.com/content/docs/doc-4511
We were then able to compile and install the kernel nation module thanks to:
. / configure
do
make installlsmod said that nation has been properly installed. Then we ran the installer for DAQmx 8.0.1 by:
. / INSTALL - nodeps
To do this, we have received errors indicating that LabView support could not be installed because check addictive (incorrectly we think) stated that labviewbase86 has not been installed; This caused the installer to have an abortion. Therefore, we refused to install support for LabView 8.6 and revived the installation program which produces the output:
Installation of the driver NOR-DAQmx Distribution of Linux Installer version 8.0.1f0...
Already to jump Edward - 1.9.0 - f0.noarch.rpm installation, same or newer
installed.Pre Installation...
Preparing... ########################################### [100%]
1:nitimingi ########################################### [ 4%]
2:nipalki ########################################### [ 7%]
3:nipali ########################################### [ 11%]
RC0.d directory not found, startup script is not accredited with init levels.
4:labview80 - rte # [14%]
5:ni653x ########################################### [ 18%]
6:nicdigi ########################################### [ 21%]
7:nidaqmxcapiexmp # [25%]
8:nidaqmxcapihelp # [29%]
9:nidaqmxcapii # [32%]
LN: create the symbolic link ' / usr/local/include/NIDAQmx.h': no such file or directory
10:nidaqmxcfgi # [36%]
11:nidaqmxef # [39%]
12:nidaqmxhelp # [43%]
13:nidaqmxinfi # [46%]
14:nidaqmxswitch # [50%]
15:nidimi ########################################### [ 54%]
16:nidsai ########################################### [ 57%]
17:nimdbgi ########################################### [ 61%]
18:nimioi ########################################### [ 64%]
19:nimru2i ########################################### [ 68%]
20:nimxdfi ########################################### [ 71%]
21:nimxpi ########################################### [ 75%]
22:nimxs ########################################### [ 79%]
RC0.d directory not found, startup script is not accredited with init levels.
23:niorbi ########################################### [ 82%]
24:nipxirmi ########################################### [ 86%]
25:nirpci ########################################### [ 89%]
26:niscarabmm # [93%]
27:niscxi ########################################### [ 96%]
28:nistci ########################################### [100%]After Installation...
At this point, after reading this report, we used the Gentoo rc update utility to add several scripts for the boot runlevel initialisation:
update of RC - a boot nipple
update of RC - a bunch of nipxirmu
update of RC - a bunch of mxssvr
update of RC - a bunch of nisvcloc
update of RC - a bunch of nidevlduWhen the computer reboots, you get an error message indicating that the following kernel modules are not: nidmxfk, nimsdrk, nimstsk and nipxirmk. lsmod shows that the nation and nipalk are installed, but no other kernel modules NOR are present. modprobe-l shows that only nation and nipalk are available.
So we have several questions:
1. we install drivers in the correct order? Should use us NI-VISA 4.5 or NOR-488. 2 rather than DAQmx 8.0.1?
2. What kernel modules should be loaded for this equipment run? How to compile and install the ones that we have yet, specifically nidmxfk, nimsdrk, nimstsk and nipxirmk? Are there others?
3. How can we get the installer to properly recognize that we have installed LabView Core and install support for LabView? Are there additional kernel modules related to the support of LabView?
4. What is the symbolic link that was not created in the DAQmx installation report? (ln: create the symbolic link ' / usr/local/include/NIDAQmx.h': no such file or directory)?
I apologize for so many questions, but these seem to be the last obstacles to obtaining OR runs correctly on this system. Is there other information that we can provide that would be useful? Thanks for any help or suggestions you can offer.
Craig
Hey Craig,.
Given that you use 64-bit Linux all kernel modules must be compiled for 64 - bit. User mode binaries can be 32-bit, assuming that you have installed the 32-bit support libraries.
NOR-DAQmx is a complex architecture and requires several kernel modules to support your PCIe card. Most of these kernel modules have not been brought to support 64-bit Linux. Some kernel modules are components infrustructure that are shared with other pilots OR as NI-VISA and NOR-488. 2 and have been brought to support 64-bit Linux. Unfortunately, you need all the modules to use your hardware.
I hope that answers your question.
Shawn Bohrer
National Instruments
-
OT:touchpad.
Hello, can you please suggest how to copy and paste the touchpad on a Toshiba portable computer Satellite C655 S5505 windows 7.
It worked a few days ago... I don't know what I did so that it does not work right. I like to copy and paste when right or click with the left button of the touchpad... They have a key on the Panel of key with copy and paste and cancel and cut options next to the bar area to the right of the ALT key with lines and an arrow on the key... Always like the old mode right click and copy and paste from the touchpad... Thank you
Hello
Check with the manufacturer of system support, documentation in line, or forums as there probably
are shortcut keys that enable and disable the touchpad functions.Toshiba has also map of keys which allow easy adjustment of the TouchPad. See support for Toshiba
and Forums. The key shortcut for the TouchPad, if they are responsible in the Fn + F9 or see the key card
So usually loaded at the top of the screen.There is also usually a TouchPad control utility that loads in the Notification area next to the clock
at the bottom right.Toshiba - Forums
http://laptopforums.Toshiba.com/Toshiba - Contacts
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contactToshiba - drivers - access your model
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=downloadToshiba - Support
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jspParameters for TouchPad located in the control panel - mouse (there may be several tabs with TouchPad
entries) and some have a utility that loads in the Notification area next to the clock in the bottom right.==========================================
This utility also allows to control the TouchPad:
TouchFreeze
http://code.Google.com/p/TouchFreeze/I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
I just finished a new construction, including Windows 7 Home Premium 64-bit. Update all the drivers went through, and now I get BSOD. Initially, I'd get them, after that the system wake up to 'sleep' mode, but this morning I received after you start the computer from the closure. They are the mistakes STOP F4, and I'm sure that there is a way to fix them, I just need help on where to start. After a few reboots to check the version of the BIOS and what not, the computer would no longer connect to the internet.
Here is my configuration:
CPU: Intel Core i3-3225 3.3 GHz Dual - Core Processor
Motherboard: ASRock H77M Micro ATX LGA1155 motherboard
Memory: G.Skill Ripjaws X Series 8 GB (2 x 4 GB) DDR3-1600 memory
Storage: Intel 330 series 240GB 2.5 "Solid State Disk
: Fractal Design Arc Mini Micro ATX mini-tower case
Power supply: Rosewill Capstone 450W 80 PLUS Gold Certified ATX12V / EPS12V power supply
Optical drive: Lite-On iHAS124-04 DVD/CD burner
Operating system: Microsoft Windows 7 Home Premium SP1 (OEM) (64-bit)
Other: 2 x Western Digital Caviar Blue 500 GB 3.5 "7200 RPM hard drive internalAnd here are two mistakes STOP I was able to capture up to now:
STOP: 0X000000F4 (0XFFFFFA800B938B30, 0XFFFFFA800B938E10, 0 X 000000000000003, 0XFFFFF80002F80460)STOP: 0X000000F4 (0XFFFFFA800BCF4B30, 0XFFFFFA800BCF4E10, 0 X 000000000000003, 0XFFFFF800031D4460)
This was my first computer build and I really enjoyed until the software part; simply too many current intangibles. A lot to learn and I'm happy to do, but my wife would like a stable computer.
Original title: how to troubleshoot and resolve problems blue screen for new construction
Hello
Bug_Check F4 is generally hard, cables, and associated hard drive controller.
Since this is a new construction House remove ALL power - reinstall all memory cards and cables (on
both ends where possible) - actually delete and replace - do not just tight. Make sure heat
sink and compound are correctly placed and that all lovers of work.Check with the ASRock support, their documentation online, the diagnosis and ask in their forum
for problems known.ASRock - Support
http://www.ASRock.com/support/index.aspASRock - Forums
http://www.ASRock.com/support/forum.aspASRock - downloads
http://www.ASRock.com/support/download.asp=============
See this article:
You receive various Stop error messages in Windows 7 or in Windows Server 2008 R2 when
you try to resume a computer that has a large hard drive SATA.
http://support.Microsoft.com/kb/977178-----------------------------------------------------------------------------------------------------------
Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65================================================================
BCCode: F4 0x000000F4
Check and reinstall the cards memory and cables (at both ends where possible) in fact
delete and replace - do not just tight. On a laptop computer on all you can do is reinstall it
memory and possibly check the connection/contacts on the hard drive. Memory could
be the problem, so if you have more than 1 stick swap them in and out to see if the
problem follows a stick or try the new memory. Antivirus/anti-spyware/security programs
have been known to cause or have a role in this matter.More general patch updates day and low level chipset BIOS drivers and other control
software.Also check the wiring on the hard drive.
Bug Check 0xF4: CRITICAL_OBJECT_TERMINATION
Important info if you received a STOP Code
If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.
If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.
These actions could prevent a mistake like this does not happen:
- Download and install updates for your computer from Windows Update device drivers.
- Scan your computer for computer viruses.
- Check your hard drive for errors.
CRITICAL_OBJECT_TERMINATION parameters
The following settings are displayed on the blue screen.
Parameter Description 1
The Terminal object type:
0x3: Process of
0x6: Thread
2
The endpoint object
3
The name of the process image file
4
Pointer to a string ASCII containing an explanatory message
Cause
Several processes and threads are necessary to the functioning of the system. As they are completed for some reason, the system can no longer function.
BCCode: F4 0x000000F4<-- read="" this="">-->
* 1241.html http://www.faultwire.com/solutions-fatal_error/A-process-or-thread-crucial-to-System-Operation-has-0x000000F4-==================================================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.Windows Vista restarts automatically if your computer encounters an error that requires him to plant
(also, Windows 7 and Windows 8).
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during ' blue screen
of death "crashes and displays the information about all crashes in one
Table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista (also Windows 7) Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlStop Windows 7 to automatically install device drivers
http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/How to disable automatic driver Installation in Windows 7 / Vista
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
Ultimate and Enterprise)
http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlHow to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
How to debug and find the exact constraint violation error
{14:22:36:ErrorCode 122712 - 1 with ErrorMessage as ORA-00001: unique constraint (OPS$ CMS.)} {PK_TB_ML_EXER_UPLOAD) violated appeared [SSO16063259009], pk_xop_subsales.pr_process_exer [CMSCOST_USER]}
{Pr_process_exer (PROCEDURE)
p_voucher_num tb_xop_order_manager_t.voucher_num%TYPE,
p_status_type tb_xop_order_manager_t.status_type%type,
p_dest tb_xop_order_manager_t.dest%type,
p_reference_key tb_xop_order_manager_t.reference_key%type,
p_seq_num tb_xop_order_manager_t.seq_num%type,
p_return_code tb_xop_order_manager_t.return_code%type,
p_reason_desc tb_xop_order_manager_t.reason_desc%type,
p_activity_qty tb_xop_order_manager_t.activity_qty%type,
p_leaves_qty tb_xop_order_manager_t.leaves_qty%type,
p_exec_price tb_xop_order_manager_t.exec_price%type,
p_current_status tb_xop_order_manager_t.current_status%type,
p_err_cur ON ref_cursor)
IS
CURSOR get_order_dtls (v_voucher_num tb_xop_order_manager_t.voucher_num%type)
IS
SELECT *.
OF tb_xop_order_manager_t
WHERE voucher_num = v_voucher_num;
CURSOR get_mail_cd (v_opt_num OPTIONEE.opt_num%TYPE) IS
SELECT mail_cd, sp_mail_cd
OF XOP_OPTIONEE
WHERE opt_num = v_opt_num;
cursor get_opt_dtls (v_opt_num OPTIONEE.opt_num%TYPE) IS
Select
SUBSTR (Trim (O.name_first) |) ' ' || Trim (O.name_mi) | ' ' ||
Trim (O.name_last), 1: 35) p_name,.
SUBSTR (O.address1, 1, 35) opt_addr1,.
SUBSTR (O.address2, 1, 35) opt_addr2,.
SUBSTR (O.address3, 1, 35) opt_addr3,.
SUBSTR (O.address4, 1, 35) opt_addr4,.
SUBSTR (O.address5, 1, 35) opt_addr5,.
SUBSTR (O.address6, 1, 35) opt_addr6,.
SUBSTR (Trim (O.City) |) ' ' || Trim (O.State) | ' ' ||
Trim (O.zip) | ' ' || Trim (O.Country), 1: 35) city_state_zip_country,.
Trim town (O.City),
Trim (O.State) State,
Trim (O.zip) zip,
Trim (O.Country) countries
of the option o holder
where o.opt_num = v_opt_num;
-CQ: PCTUP00210726 - added wire instructions audit for info thread deleted.
CURSOR (c_wire_instruction)
in_wire_seq_no TB_XOP_WIRE_INSTRUCTIONS.wire_seq_no%TYPE) IS
SELECT ml_brok_acct_num,
SSN,
plan_num,
instr_type,
aba_routing_num,
swift_routing_code,
bank_name,
bank_acct_num,
name_on_account,
bank_addr_1,
bank_addr_2,
bank_addr_3,
City,
State,
countries,
zip,
bank_ident_num,
addtl_info
OF TB_XOP_WIRE_INSTRUCTIONS
WHERE wire_seq_no = in_wire_seq_no
UNION
SELECT ml_brok_acct_num,
SSN,
plan_num,
instr_type,
aba_routing_num,
swift_routing_code,
bank_name,
bank_acct_num,
name_on_account,
bank_addr_1,
bank_addr_2,
bank_addr_3,
City,
State,
countries,
zip,
bank_ident_num,
addtl_info
OF TB_XOP_WIRE_INSTRUCTIONS_AUDIT
WHERE wire_seq_no = in_wire_seq_no;
CURSOR c_order_qty IS
SELECT order_qty
OF tb_xop_order_manager
WHERE voucher_num = p_voucher_num;
v_order_qty tb_xop_order_manager.order_qty%TYPE;
v_wire_instruction c_wire_instruction % ROWTYPE;
v_order_dtls get_order_dtls % rowtype;
v_opt_dtls get_opt_dtls % rowtype;
v_settle_dt tb_ml_exer_upload.settle_dt%type;
v_cusip_num corp.cusip_num%type;
number of v_err_cd (12): = 0;
v_err_msg varchar2 (4000);
v_compy_nme tb_fc_Compy.compy_nme%type;
v_ml_sec_num tb_fc_compy.ml_sec_num%type;
v_mail_cd xop_optionee.mail_cd%type;
v_count1 PLS_INTEGER: = 0;
v_sum_activity_qty tb_xop_order_manager_t.activity_qty%TYPE;
v_transact_no PLS_INTEGER;
v_ivr_plan_num tb_fc_compy.ivr_plan_num%TYPE;
wait_for_more EXCEPTION;
exceeds_order_qty EXCEPTION;
-Added CQ # PCTUP00481233
number of v_sub_totfee;
number of v_sub_fixedfee1;
number of v_sub_fixedfee2;
number of v_sub_fixedfee3;
number of v_sub_secfee;
number of v_sub_feenum;
-Added CQ # PCTUP00481233
v_fixedfee1 tb_xop_order_manager_t.fixed_fee1%TYPE; -SPIF # 43161 - variable to contain the fixed mensuels1
BEGIN
OPEN c_order_qty.
SEEK c_order_qty INTO v_order_qty;
CLOSE C_order_qty;
DBMS.output.put_line ('completed1');
IF v_order_qty <>p_activity_qty THEN
DBMS.output.put_line ('completed2');
IF p_status_type = "EO" AND v_order_qty < p_activity_qty THEN
RAISE exceeds_order_qty;
DBMS.output.put_line ('completed3');
ELSIF p_status_type = 'EO' AND v_order_qty > p_activity_qty THEN
-Partial enforcement
INSERT INTO tb_xop_hold_multi_orders
(voucher_num
reference_key
seq_num
return_code
reason_desc
status_type
activity_qty
leaves_qty
exec_price
current_status
waiting
activ_dt)
VALUES
(p_voucher_num
p_reference_key
p_seq_num
p_return_code
p_reason_desc
p_status_type
p_activity_qty
p_leaves_qty
p_exec_price
p_current_status
, 'Y'
SYSTIMESTAMP);
DBMS.output.put_line ('completed4');
ON THE OTHER
IF p_status_type = "BE" THEN
SELECT COUNT (1) IN v_count1
OF tb_xop_hold_multi_orders
WHERE voucher_num = p_voucher_num;
DBMS.output.put_line ('completed5');
IF v_count1 > 0 THEN
INSERT INTO tb_xop_hold_multi_orders
(voucher_num
reference_key
seq_num
return_code
reason_desc
status_type
activity_qty
leaves_qty
exec_price
current_status
waiting
activ_dt)
VALUES
(p_voucher_num
p_reference_key
p_seq_num
p_return_code
p_reason_desc
p_status_type
, (-1) * p_activity_qty
p_leaves_qty
p_exec_price
p_current_status
, 'Y'
SYSTIMESTAMP);
UPDATE tb_xop_hold_multi_orders
QUEUE = 'Y '.
WHERE voucher_num = p_voucher_num;
DBMS.output.put_line ('completed6');
END IF;
END IF;
END IF;
DBMS.output.put_line ('completed7');
SELECT SUM (NVL(activity_qty,0)) IN the v_sum_activity_qty
OF tb_xop_hold_multi_orders
When pending = 'Y '.
AND voucher_num = p_voucher_num;
IF v_sum_activity_qty > 0 THEN
IF v_sum_activity_qty <>v_order_qty THEN
RAISE wait_for_more;
ON THE OTHER
-final order in the case of partial performance; complete the process
UPDATE tb_xop_hold_multi_orders
PUT on hold = ' don't
process_dt = SYSDATE
WHERE voucher_num = p_voucher_num;
END IF;
END IF;
END IF;
UPDATE tb_xop_order_manager_t
SET activ_dt = TO_CHAR (SYSDATE, "YYYY-MM-DD HH24:MI:SS") | '. 000'
dest = p_dest
reference_key = p_reference_key,
seq_num = p_seq_num
return_code = p_return_code
reason_desc = p_reason_desc,
status_type = p_status_type
, activity_qty = v_order_qty - p_activity_qty
, leaves_qty = 0 - p_leaves_qty
exec_price = p_exec_price,
WHERE voucher_num = p_voucher_num;
DBMS.output.put_line ('completed8');
/*
* SPIF # 43161 - update of the current situation to the PO moved to the end, even in works of the PROD.
*/
IF (p_status_type = "EO") THEN
BEGIN
Select cusip_num
in v_cusip_num
Corp;
EXCEPTION
WHEN NO_DATA_FOUND THEN
SELECT cusip_num
IN v_cusip_num
OF tb_xop_espp_compy
WHERE compy_acronym = replace (replace(user,'CMS'), '_USER');
WHILE OTHERS THEN
NULL;
END;
Select compy_nme, ml_sec_num, ivr_plan_num
in v_compy_nme, v_ml_sec_num, v_ivr_plan_num
of tb_fc_compy
where compy_acronym = replace (replace(user,'CMS'), '_USER')
UNION ALL
Select compy_nme, je_ml_security_number, ivr_plan_num
of tb_xop_espp_compy
where compy_acronym = replace (replace(user,'CMS'), '_USER');
-where ivr_plan_num = replace (substr(p_voucher_num,1,7), 'NORTH', 'XOP');
Open get_order_dtls (p_voucher_num);
SEEK get_order_dtls INTO v_order_dtls;
v_settle_dt: = fn_xop_bankopen_bizday (TRUNC (v_order_dtls.exer_date + 1));
v_settle_dt: = fn_xop_bankopen_bizday (TRUNC (v_settle_dt + 1));
v_settle_dt: = fn_xop_bankopen_bizday (TRUNC (v_settle_dt + 1));
FOR c_mail_cd IN get_mail_cd (v_order_dtls.opt_num)
LOOP
v_mail_cd: = c_mail_cd.mail_cd;
-We need get sp_mail_cd and overlay with the sp_mail_cd in order_manager_t?
END LOOP;
OPEN get_opt_dtls (v_order_dtls.opt_num);
SEEK get_opt_dtls INTO v_opt_dtls;
CLOSE Get_opt_dtls;
v_fixedfee1: = nvl (v_order_dtls.fixed_fee1, 0);
/*
* SPIF # 43161 - at least one transaction per day fees
*/
v_fixedfee1: = pk_xop_enh_exerupdate.chrg_tranxfixed_fee (v_fixedfee1,
v_order_dtls. Symbol,
v_order_dtls.corp_acronym,
v_order_dtls.opt_num);
-Insert in tb_ml_exer_upload
-Added CQ # PCTUP00481233
Pk_Xop_Transactmodel.GET_FEE (v_order_dtls. GROUP_ID, v_order_dtls. SVC_ID, 'SQ', v_order_dtls.opts_exer,
round (v_order_dtls.exec_price, 4), v_sub_totfee, v_sub_fixedfee2, v_sub_fixedfee1,.
v_sub_fixedfee3, v_sub_secfee, v_sub_feenum, LPAD (v_order_dtls. SSN, 9, 0));
v_order_dtls.sec_fee: = v_sub_secfee;
UPDATE tb_xop_order_manager_t
SET sec_fee = v_sub_secfee
WHERE voucher_num = p_voucher_num;
DBMS.output.put_line ('completed8');
-End CQ # PCTUP00481233
INSERT INTO tb_ml_exer_upload
(exer_num, exer_seq,
exer_dt, written_flag, backout_flag, output_line,
je_flag, opts_exer,
tot_tax, shrs_sold, comm_value, tot_fee,
mkt_prc, exer_type, soc_sec,
name_first, name_mi,
name_last, check_addr_1, check_addr_2, check_addr_3,
check_addr_4, check_addr_5, city, state, zip, country,.
city_state_zip_country,
p_name, opt_addr1, opt_addr2, opt_addr3, opt_addr4,
opt_addr5, opt_addr6,
settle_dt, send_to_citibank_flag,
dom_chek_distr, foreign_currency_code,
distribution_method, wire_seq_no,
cusip_num, ml_retail_account, multi_curr_handling_fee,
ml_sec_num, corp_name, upd_optionee_addr,
outbound_flag,-there are N
corp_symbol, taxwire_approve,-not make applicaplabe
exersource,
mail_cd, sp_mail_cd,
backup_withholding,
user_id,
acct_num_othr)
VALUES (v_order_dtls.exer_num, 0, v_order_dtls.exer_date, 'No', not, NULL,)
-Would be PG 12/12/05 Changed to fill the resulting je_flag of dom_chek_distr',.
-PG 16/12/05 I should not be generated for international controls... If 'Y' always
'Y',-je_flag
v_order_dtls.opts_exer, 0,-total tax will be 0.
v_order_dtls.opts_exer, shrs_sold,
v_order_dtls.comm_value,
-SPIF # 43161 - replaced nvl (v_order_dtls.fixed_fee1, 0), with v_fixedfee1
v_fixedfee1 + nvl(v_order_dtls.fixed_fee3,0) + nvl(v_order_dtls.sec_fee,0), - v_order_dtls.fees_amt,
round (v_order_dtls.exec_price, 4), v_order_dtls.exer_type.
LPAD (v_order_dtls. SSN, 9, '0'),-v_order_dtls.ssn, modified by Suresh on 08/02/07 for SPIF # 37210
v_order_dtls.name_first, v_order_dtls.name_mi, v_order_dtls.name_last,
v_order_dtls.check_addr_1, v_order_dtls.check_addr_2, v_order_dtls.check_addr_3,
v_order_dtls.check_addr_4, v_order_dtls.check_addr_5, NVL (v_order_dtls. City, v_opt_dtls. (City),
NVL (v_order_dtls. State, v_opt_dtls. State), NVL (v_order_dtls.zip, v_opt_dtls.zip).
NVL (v_order_dtls. Country, v_opt_dtls. (Country),
SUBSTR (nvl (v_order_dtls.city | v_order_dtls.)) State | v_order_dtls.zip | v_order_dtls. Country,
v_opt_dtls.city_state_zip_country), 1: 34),-COLUMN LENGTH MAX IS 35
v_opt_dtls.p_name, v_opt_dtls.opt_addr1, v_opt_dtls.opt_addr2, v_opt_dtls.opt_addr3,
v_opt_dtls.opt_addr4, v_opt_dtls.opt_addr5, v_opt_dtls.opt_addr6,
v_settle_dt, Decode(v_order_dtls.distribution_method,'W','Y','D','Y','C','Y','D'),
v_order_dtls.dom_chek_distr, v_order_dtls.foreign_currency_code,
v_order_dtls.distribution_method, v_order_dtls.wire_seq_no,
v_cusip_num, v_order_dtls.acct_num, v_order_dtls.multi_curr_handling_fee,
-nvl (fn_get_sec_num (replace (substr (p_voucher_num, 1, 7), 'NORTH', 'XOP'), v_order_dtls.symbol), v_ml_sec_num).
NVL (fn_get_sec_num (v_ivr_plan_num, v_order_dtls.symbol), v_ml_sec_num).
v_compy_nme, v_order_dtls.upd_optionee_addr,
'N'-' is for outgoing flag.
v_order_dtls. Symbol, 'd', --a ' for disabled taxwires
The of ', - the of ' source being a subsequent sale.
v_mail_cd, need to get mail_Cd?
v_order_dtls.sp_mail_cd, v_order_dtls.backup_withholding,
(User, v_order_dtls.acct_num_othr);
IF (NVL(v_order_dtls.wire_seq_no,0) > 0) THEN
OPEN c_wire_instruction (v_order_dtls.wire_seq_no);
SEEK c_wire_instruction INTO v_wire_instruction;
CLOSE C_wire_instruction;
INSERT INTO TB_XOP_TRANSACT_WIRE_INSTR
(user_id, exer_num, wire_seq_no, ml_brok_acct_num, ssn,
plan_num, instr_type, aba_routing_num,
swift_routing_code, bank_name, bank_acct_num,
name_on_account, bank_addr_1, bank_addr_2, bank_addr_3,
City, State, country, zip, bank_ident_num, addtl_info)
VALUES
(USER, v_order_dtls.exer_num, v_order_dtls.wire_seq_no,
v_wire_instruction.ml_brok_acct_num, v_wire_instruction.ssn,
v_wire_instruction.plan_num, v_wire_instruction.instr_type, v_wire_instruction.aba_routing_num,
v_wire_instruction.swift_routing_code, v_wire_instruction.bank_name, v_wire_instruction.bank_acct_num,
v_wire_instruction.name_on_account, v_wire_instruction.bank_addr_1, v_wire_instruction.bank_addr_2,
v_wire_instruction.bank_addr_3, v_wire_instruction.city, v_wire_instruction.state, v_wire_instruction.country, v_wire_instruction.zip,
(v_wire_instruction.bank_ident_num, v_wire_instruction.addtl_info);
DBMS.output.put_line ('completed10');
END IF;
/ * PG 05/01/06 call conversion check only for international controls and son * /.
IF = v_order_dtls.dom_chek_distr ' n AND v_order_dtls.distribution_method IN ('W' ' d ","C"" ") THEN
/ * PG 20/12/05 to treat the subsequent sales with the wire or the distribution of currency * /.
v_transact_no: = 88;
pk_xop_citibank_forex.pr_cashconversion_ins_request (v_order_dtls.acct_num
LPAD(v_order_dtls.ssn,9,'0') - v_order_dtls.ssn, modified by Suresh on 15/02/07 for SPIF # 37210
v_order_dtls.distribution_method
v_order_dtls.foreign_currency_code
v_order_dtls.wire_seq_no
, TOWER ((v_order_dtls.opts_exer * ronds (v_order_dtls.exec_price, 4)), 2)
-ROUND(v_order_dtls.comm_value,2)
-ROUND (nvl(v_order_dtls.fixed_fee1,0) + nvl(v_order_dtls.fixed_fee3,0) + nvl(v_order_dtls.sec_fee,0), 2)
-nvl(v_order_dtls.multi_curr_handling_fee,0)
-product net nvl(v_order_dtls.backup_withholding,0)-
, v_order_dtls.multi_curr_handling_fee - handling fee
-Modified by Billon/Suresh on 03/02/2006-, v_order_dtls.login_name
, CASE v_order_dtls.login_name WHEN ' CUSTOMER /' THEN v_order_dtls.login_name |' SSO' ELSE v_order_dtls.login_name |' / SSO' END
, v_transact_no - transact_no as a placeholder for the 88 exer_type
v_order_dtls.check_addr_1
v_order_dtls.check_addr_2
v_order_dtls.check_addr_3
v_order_dtls.check_addr_4
v_order_dtls.upd_optionee_addr
v_order_dtls.city
v_order_dtls.state
v_order_dtls.zip
v_order_dtls.country
v_order_dtls.login_ipaddress
v_order_dtls.fcnum
v_order_dtls.opt_num
v_settle_dt,
p_exer_num = > v_order_dtls.exer_num
);
END IF;
COMMIT;
close get_order_dtls;
END IF;
/*
* SPIF # 43161 - update of current status in IN. is moved to this part, even PROD.
*/
UPDATE tb_xop_order_manager_t
SET exec_dttime = decode (p_status_type, "EO", to_char (sysdate, 'DD-MON-YYYY HH24:mi:ss'), null)
exer_date = trunc (sysdate)
, cancel_dttime = decode (p_status_type, 'CX', to_char (sysdate, 'DD-MON-YYYY HH24:mi:ss'), 'UR', to_char (sysdate, "MON-DD-YYYY HH24:mi:ss), null)
, current_status = "PO."
sum_status = decode(p_status_type,'EO','X','C'),
sum_stat_dttime = SYSDATE
WHERE voucher_num = p_voucher_num;
v_err_cd: = sqlcode;
v_err_msg: = sqlerrm;
Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
EXCEPTION
DBMS.output.put_line ('completed200');
/ * PG 02/10 managed 'order of partial fill' exception * /.
When wait_for_more then
v_err_cd: = 0;
v_err_msg: = ' ORA-0000: normal completion, successfully ';
pr_xop_log_errors (' partially filled;) Pending-activity qty:' | TO_CHAR (v_sum_activity_qty) | "pk_xop_subsales.pr_process_exer");
Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
When exceeds_order_qty then
v_err_cd: = sqlcode;
v_err_msg: = sqlerrm;
Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
pr_xop_log_errors ("exceeded the amount of activity Order_qty - activity qty: ' | ') TO_CHAR (p_activity_qty) | "pk_xop_subsales.pr_process_exer");
while others then
v_err_cd: = sqlcode;
v_err_msg: = sqlerrm;
Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
pr_xop_log_errors (' error code ' | ') SQLCODE |' with ErrorMessage like ' | SQLERRM |' occurred '. the user | (' pk_xop_subsales.pr_process_exer');
DBMS.output.put_line ('completed125');
END pr_process_exer;
}
Hi friends, any1 help me how set ref-cursor in the declaration section and how to find the constraint error situation has occurred...956684 wrote:
Hello.Friends please help... How to debug and find the exact position of the constraint violation... Thank you for the help...
It's not a way to track it unless you have taken the exception raised.
As a way to start debugging, you will need to monitor
1. all DML against the Table on which you have constraint. Specifically, the DML that Act on the column you will be forced.
2. use the exception handling, to record the error and the data that causes the constraint to fail.
3. don't forget to monitor triggers, if used, could write data in the column you have forced on.Or
Another track is to:
select * from user_source where lower(text) like '%your_table_name%'; order by type, name, line;
Look at the lines, exclude that are in the statement or in the SELECT statements and targets of the DML.
Looking at the unformatted code, that you have published, this statement looks like a culprit.
INSERT INTO tb_ml_exer_upload (exer_num,exer_seq, exer_dt, written_flag, backout_flag, output_line, je_flag, opts_exer, tot_tax,shrs_sold,comm_value,tot_fee, mkt_prc,exer_type, soc_sec, name_first, name_mi, name_last,check_addr_1,check_addr_2,check_addr_3, check_addr_4,check_addr_5,city,state,zip,country, city_state_zip_country, p_name,opt_addr1,opt_addr2,opt_addr3,opt_addr4, opt_addr5,opt_addr6, settle_dt,send_to_citibank_flag, dom_chek_distr,foreign_currency_code, distribution_method,wire_seq_no, cusip_num, ml_retail_account,multi_curr_handling_fee, ml_sec_num, corp_name,upd_optionee_addr, outbound_flag, -- make it N corp_symbol,taxwire_approve, -- make it not applicaplabe exersource, mail_cd, sp_mail_cd, backup_withholding, user_id, acct_num_othr) VALUES(v_order_dtls.exer_num,0,v_order_dtls.exer_date,'N','N',NULL, -- PG 12/12/05 Changed to populate the je_flag based on dom_chek_distr 'D', -- PG 12/16/05 JE should not be generated for international checks.. So 'Y' always 'Y', --je_flag v_order_dtls.opts_exer,0,--total tax will be 0. v_order_dtls.opts_exer, --shrs_sold, v_order_dtls.comm_value, --SPIF# 43161- replaced nvl(v_order_dtls.fixed_fee1, 0) with v_fixedfee1 v_fixedfee1 + nvl(v_order_dtls.fixed_fee3,0) + nvl(v_order_dtls.sec_fee,0), --v_order_dtls.fees_amt, round(v_order_dtls.exec_price, 4),v_order_dtls.exer_type, LPAD(v_order_dtls.ssn,9,'0'), --v_order_dtls.ssn, Modified by Suresh on 02/08/07 for SPIF # 37210 v_order_dtls.name_first,v_order_dtls.name_mi,v_order_dtls.name_last, v_order_dtls.check_addr_1,v_order_dtls.check_addr_2,v_order_dtls.check_addr_3, v_order_dtls.check_addr_4,v_order_dtls.check_addr_5,nvl(v_order_dtls.city,v_opt_dtls.city), nvl(v_order_dtls.state,v_opt_dtls.state),nvl(v_order_dtls.zip,v_opt_dtls.zip), nvl(v_order_dtls.country,v_opt_dtls.country), SUBSTR(nvl(v_order_dtls.city||v_order_dtls.state||v_order_dtls.zip||v_order_dtls.country, v_opt_dtls.city_state_zip_country),1,34), -- COLUMN LENGTH MAX IS 35 v_opt_dtls.p_name,v_opt_dtls.opt_addr1,v_opt_dtls.opt_addr2,v_opt_dtls.opt_addr3, v_opt_dtls.opt_addr4,v_opt_dtls.opt_addr5,v_opt_dtls.opt_addr6, v_settle_dt,decode(v_order_dtls.distribution_method,'W','Y','D','Y','C','Y','D'), v_order_dtls.dom_chek_distr,v_order_dtls.foreign_currency_code, v_order_dtls.distribution_method,v_order_dtls.wire_seq_no, v_cusip_num,v_order_dtls.acct_num,v_order_dtls.multi_curr_handling_fee, -- nvl(fn_get_sec_num(replace(substr(p_voucher_num,1,7),'SSO','XOP'),v_order_dtls.symbol),v_ml_sec_num), nvl(fn_get_sec_num(v_ivr_plan_num, v_order_dtls.symbol),v_ml_sec_num), v_compy_nme,v_order_dtls.upd_optionee_addr, 'N', --'N' is for outbound flag. v_order_dtls.symbol,'D', --'D' for taxwires disabled 'S', -- 'S' for source being subsequent sale. v_mail_cd, --need to get mail_Cd?? v_order_dtls.sp_mail_cd,v_order_dtls.backup_withholding, user,v_order_dtls.acct_num_othr);
What is the structure of the tb_ml_exer_upload Table and the columns do you have constraints?
Which column of the tb_ml_exer_upload table is your primary key (because the constraint name mentions pk_tb_ml_exer_upload)?Published by: Jen K on January 4, 2013 12:57
-
How to compress and decompress the file in mac
How to compress and decompress the file in mac
I will use third party software to do this.
-
How to find and delete the dupes in Photos
How to find and remove the many dupes in Photos
Duplicate Finder in the App Store will clean the photo library. However, I would be careful to make sure that nothing is really a duplicate.
-
Satellite A30 921: how to remove and replace the memory?
Hi, can someone help me how to remove and replace the memory of satellite A30 921. and also, please give a detailed instruction.
Thank you in advance.
Hello
There is not much to explain. On the low side in the Middle it is placed to cover memory (fixed with two screws). Remove the cover and you will see 2 slots there. I put t know how much memory you here but like Stefan says you can use max 2 GB of RAM (2 x 1024Mo PC2700 - PA3313U-1M1G). How to remove the memory modules, which you can see on http://www.hardwaresecrets.com/article/189/5
Good bye
Maybe you are looking for
-
Satellite A40 - boot sequence problems
Hello! I just bought a used Toshiba Satellite A40. He had a almost crashed Windows XP is installed. I'm trying to put a new copy of Windows XP on it, but I can't boot from the CD. By pressing the done nothing F12 key and when I access BIOS (v. 1.50),
-
How to set the junk e-mail folder in Mail ios9?
In other computers and devices, all my IMAP accounts have folder 'Spam' set for managing junk e-mail. And ios devices continue to create a folder called "Junk," and you really can't tell ios9 this folder to use for spam? Really? version 9 of the soft
-
I have a new server and you cannot use Remote Desktop connection.
I HAVE A NEW SERVER (HP ML110 G6) AND HAVE USED OLD HARD DISKS, BUT MY REMOTE DESKTOP CONNECTION WILL NOT ME OR OTHERS - WHAT COULD THE REASON BE?
-
How to merge two partitions in XP
I have Windows XP Service Pack 3. The space becomes very low on my NTFS Partition that contains Windows XP. There are partition with more than 100 GB of free space I want to access - preferably by merging two partitions or not not to resize the NTFS
-
Is it possible to have multiple windows of the same file open?
Hello I was wondering if it is possible to have multiple windows of the same file open at the same time in Windows XP? Thank you! Dave