How to configure my router 700 minutes using a Macbook?

Similar Questions

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140

• Re: How to configure Ant in adf application using Jdeveloper 11.1.2.3.0?

  Hi all

  I use jdev 11.1.2.3.0.

  Any can help me how to configure Ant in adf application using Jdeveloper 11.1.2.3.0?

  With respect,

  satishkumarN

  HI Sissi,

  Your question is not able to understand. I guess you are looking for building project using ant for deployment.

  Please find the links below

  Construction projects with Ant

  Use of Maven in JDeveloper 11.1.2: asked to build ADF with Maven using Ant ojdeploy

  One size does not fit all: using ojdeploy and Ant to create pots of ADF library

  Thank you

  Nitesh

• How to configure HP ENVY 700 - 210xt to install the graphics card EVGA 650 TI boost.

  Can someone tell me how to install the graphics card EVGA 650 TI boost in the

  HP ENVY 700-210xt

  Product number: E9G99AV

  I replaced the power supply with Corsair RM 650 watt power supply that works very well. Now, I want to go to the graphics card EVGA 650 TI boost. Except, I can't get the driver to load with period of installed equipment. When I put the card into the PCI 16 x slot the computer starts with a blank screen. I pass the DVI video port old computer and the new port card white screen of same at startup. If I turn the PCIe port disabled in BIOS, it starts with the embedded video, but same thing impossible to load drivers that are not able to locate the new video card hardware. Makes me crazy! I don't know that I don't know how to configure the Bios correctly or something. Can anyone help?

  Hello:

  Please see my response to your other post on the link below.

  http://h30434.www3.HP.com/T5/desktop-hardware/how-to-configure-to-install-EVGA-650-TI-boost-video-car-in/m-p/3117171#M71438

• How to configure VPN remote access to use a specific Interface and the road

  I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS

  I added the new WAN using another interface (newwan).

  The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside).

  I used the ASDM GUI to make changes and most of it works.

  That is to say. The default route goes via (newwan)

  Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this.

  The only problem is that remote incomming VPN access Anyconnect do not work.

  I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not...

  I can either ping external IP address from an external location.

  It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface?

  The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original

  Pointers appreciated.

  William

  William,

  As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default.

  In one of the designs that I saw that we did something like that.

  (ISP cloud) - edge router - ASA.

  The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked.

  On routers, this kind of situation is easily solved using VRF-lite with crypto.

  M.

• How to configure the service objective for use minimization?

  Hi all

  I worked on a minimization problem (for more details, see this post).  I figured out how to run an unconstrained minimization, but can not quite understand why my thread objective function remains broken.  Here is a screenshot:

  

  Any ideas?

  I understand not under this main VI of the example, a subroutine that performs the minimization and a subroutine that is called when the minimization.  As it seems that I am limited to 3 accessories, I will add some sample data to the first answer I will generate.

  Thank you very much

  RipRock

  Hi all

  I just thought of it.  For those who may be confused, as well, the answer is: follow the directions!  RTFM!  In other words, if you use the template provided to the function of labview\vi.lib\gmath\NumericalOptimization\ucno_objective template.vit, rather than recreate the code in the example, it works.

  Sorry for these positions - and thank you for your attention,

  RipRock

• Dell inspiron 3521 (i5), how to configure Radeon video card laptop use as main graphics card?

  Hello guys.

  IM using Dell inspiron 3521 (version i5 to 1.7 ghz, Radeon HD 7670 M / Intel HD Graphics 4000, 6 GB of ram)

  I don't want to use the Intel HD video card at all, because the quality of the texture is so low. I would like to know, how to set up the main video card?

  Its possible?

  Thank you

  The 'main' video chip is the Intel one - it's the only one who has a connection to your display board.  The AMD GPU is a co-processor - it can be used (chosen from the AMD Catalyst Control Panel) for the applications you want to use it.

  It CAN be made the default GPU - GPU from Intel's wired for this role.  By design, all of the video data through the Intel GPU (which is part of the central unit of system processing).

• How to configure file compare preference of using Guiffy

  I used Guiffy file comparison operations and that you have configured Dreamweaver CS4 preferences sice, but preference has gone far and nothing that I do work. When I try to make a comparison with the remote server I get full file activity, but no result.

  Thank you!

  The answer for anyone else interested is guiffyCL.command

• How to configure a router modem

  Comment know ke my modem is set up in router mode knowing c UN modem cable pay to be able to watch TV.

  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Please get your language in the drop-down list above pour post your question in the language of your choice. The forum you posted is in English only. If you can't find the language of your choice above, options of fees to pay to other international destinations can be found by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Thank you.

• How to configure Oracle Financials R12 to use https

  Hello world
  We currently use http to access our Oracle Financials R12 and want to use the https protocol. I'm trying to find the Metalink document which describes what is involved to achieve this goal, but did not have much luck.
  Thanks colin

  PL see MOS Doc 376700.1 (SSL in Oracle E-Business Suite Release 12 activation)

  HTH
  Srini

• How to configure NTP between Virtual Machines without using Vsphere Client

  I have a group of 8 virtual servers of 5.5 ESXi without an Internet connection. There are virtual machines on each of these 8 virtual servers.

  I did one of these 5.5 virtual ESXi host a NTP server by editing the file /etc/ntp.conf with below configuration and

  started the ntpd daemon. He began to take the time to its local clock, here's the output of ntpq Pei

  IP server 10.108.190.14

  ip address of the client 10.108.190.15

  Server /etc/ntp.conf

  > > driftfile/var/lib/ntp/drift

  > > server 127.127.1.0 maxpoll 4

  > > fondant 127.127.1.0 stratum 10

  | ntpq Pei

  |   refid distance st t when poll reach delay offset jitter

  | ==============================================================
  | * LOCAL (0). LIUX. 10 l 2 64 377 0.000 0.000 0.001

  Then I edited the file /etc/ntp.conf on customers with below configuration but the customer would not synchronize with the server. He

  wouldn t get response from the server. Here is the output of ntpq Pei

  Customer /etc/ntp.conf

  > > driftfile/var/lib/ntp/drift

  > > server 10.108.190.14 iburst

  | ntpq Pei

  |      refid distance st t when poll reach delay offset jitter

  | ==================================================================
  | 10.108.190.14 INIT. 16 u

  Now, when I configure NPT Client/Server on virtual machines through the Configuration Option under Option Configuration time

  in Vsphere Client everything works fine and the client and the server to synchronize with each other. I checked the file /etc/ntp.conf on both the client

  and the server and it has a couple of restrict 127.0.0.1 and restrict the lines added by default kod nomodify etc.

  So why NPT Server featured when enabled via Vsphere Client works very well, but it does not work when it is configured manually

  in the virtual servers directly.

  I was connected to a vCenter Server Appliance through the VSphere Client and enabled the synchronization of time of the NPT.

  I really need to know how to configure the NTP server without using the Vsphere Client so that I can automate the

  task by writing a python script that would connect to each virtual server and NTP Client/Server configuration.

  Any help in this issue deeply appreciated!

  Thank you!

  You can configure the ntp server without using viclient.

  Take a look @ http://kb.vmware.com/selfservice/documentLinkInt.do?micrositeID=&popup=true&languageId=&externalID=1003063

  Hope this helps

  -Assane

• Need help Configureing Netgear router so I can connect to Playstation Network.

  My playstation 3 says "Failure of Type NAT" and will not sign into the playstation network. I have a router Netgrear that connect PS3 to Internet, but times out when you try to connect to the PS network. How can I configure the router? I use a wired connection.

  Hello

  I suggest you to contact the manufacturer of the playstation for assistance on this issue.

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• How can I create a simple VM using the EFI firmware?

  I created a VM with OS 'Another 64 - bit' and edited the .vmx file, change only the "bios" = firmware firmware = "efi".

  Whenever I start the virtual machine, it uses the BIOS instead of the EFI. I can see when to start directly to the firmware, or by starting with a 8.1 Windows Installer disk and installing Windows checking connects immediately after that it started ("" detected boot environment: legacy ' ").

  How create/configure a virtual machine to use systematically the EFI, without her 'crush' or 'back' to my configuration?

  I use VMware Fusion 7.1.0 (2314774).

  Hi michielvoo

  Welcome to the VMware communities forum.

  I wrote an article on the use of EFI in a machine virtual here: Boot via the EFI firmware | PlanetVM

  Basically, what you're doing are correct. The part, I wonder about is if the double quote characters you use double quotes a normal and not the "fantasies" (as you can see in the above article, these are those fancy)

  It takes standard double quotes on your keyboard.

  Another possible reason to make it work is not is if you edit the vmx while your merger still works as he could return your changes to protect the virtual machine.

  If you don't know everything that's wrong with your vmx file, then send the vmware.log file is also in this folder to an answer here and I or someone else will take a look and see if everything's okay what is wrong.

  --

  Wil

• How to configure the network home wiFi with dlink router

  I need to create a home network using the dlink WiFi router
  a computer with Vista and the second with XP
  can someone tell me what havo to do to configure the router etc etc o give me same informamation on where I can learn to do
  I want just the old pc with xp for the server and the vista one customer but more importantly I need the file on XP to migrate under vista.
  Thank you very muche for your end of the patient cooperation
  in return, I give free cooking classes
  see you soon

  I'm not sure if you are asking how to set up a secure wireless network, if you ask how to share files between your two computers (and there is no "customer" or "server" in a working group, in a field - which is not), or both.

  So I will give you information on doing both.

  Router - configure manually

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.
  2. attach a class (usually supplied with the router) ethernet cable cat5e port Internet/WAN from the router to the ethernet port on the cable modem.
  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.
  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

  Networking

  Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  XP - configure Windows to login automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  Vista - Start ORB > Search > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.
  MS - MVP - Elephant Boy computers - don't panic!

• How to configure the different VLANs (using the E3200)?

  Hello.

  I want to implement different VLANs (using the E3200) so that I can have two different networks that cannot access each other.

  The E3200 is connected to a modem for internet access.

  I would like that the two networks to access the internet.

  The only E3200 does support the creation of VLANs?

  If not, is there another way I can satisfy the requirement by using the single E3200 (using something else than VLANs)?

  At the end of the day, I think that I would need at least another router.

  Thus, for example,.

  Router a (E3200) is connected to the configuration / modem to DHCP with a rank 192.168.1.1/24 LAN IP address.

  Router B is connected to the router and Setup for DHCP by using a LAN IP range 192.168.2.1/24.

  This peripheral way connected to the router A should not have access to devices connected to router B and vice versa, correct?  For example, X device connected to the router cannot ping or browse files on the device is connected to router B and vice versa, correct?

  Do I need to configure anything else on router B?  For example, do I need the DNS configuration settings so that devices connected to router B can connect to the internet without problem?  Do I need to specify that these VLANs are not bridged and which router, or both?

  I already know how to configure a static IP address, DHCP, beaches LAN IP and static DNS settings on a router, etc.

  With respect to wireless devices, I think that they would follow the same model; for devices connected to the router wireless (E3200) have access to other devices Wi-wired and connected to the router, but not to devices with or without wire, connected to router B and vice versa.  However, if the wireless devices have currently access to wired devices was also connected to the router, so it's good for now.

  Thank you very much!

  -Rami

  The E3200 has no support VLAN according to the manual. There is no way to configure two separate networks with this single router.

  You need to add network electronics.

  Ex:

  Managed with VLAN switch

  Another wireless router with VLAN

  If your modem provides several public or private IP addresses, then you could put a switch after the modem and two wireless routers that are attached to the switch.