How to connect VMware to SAN

Hello

I have configured SAN with RAID 10 and 3 volumes of 1 TB each. I have 3 Dell server that I want to connect to the SAN. I SAN of Dell and dell powerConnect switch. To connect my machine EXi to SAN, do I have to master. (ISCSI and VMware traffic?

Any help would be appreciated

SAN F/C controller - need to set up a group of FABRIC

===================================================================

Reference DELL SERVER (ESX) with port HBA card F/C 1 connect to the port of SWITCH SAN DELL F/C 1

DELL SERVER B (ESX) with F/C map HBA 1 port to connect to the port of SWITCH SAN DELL F/C 2

DELL SERVER C (ESX) with F/C map HBA 1 port to connect to the port of SAN DELL F/C 3 SWITCH

STORAGE SAN DELL F/C 1 connected to SWITCH SAN DELL F/C 7

Read/write of data via SAN F/C

Ethe LAN Controller - (optional) to set up the Group VLAN

===================================================================

Reference DELL SERVER (ESX) with Ethe port card NIC 1 connect to the DELL LAN SWITCH ELE 1 port

DELL SERVER B (ESX) with Ethe card NIC 1 port to connect to the port of SWITCH LAN DELL ELE 2

DELL SERVER C (ESX) with Ethe port card NIC 1 connect to the port of SWITCH LAN DELL Ethe 3

NETWORK STORAGE SAN DELL 1 connected to Ethe DELL LAN SWITCH 7

Management of the system through LAN Ethe

Additional VCenter Server to configure all ESXs

Trunking is not necessary.

Tags: VMware

Similar Questions

  • How to connect to iSCSI SAN without compromising security

    Hello:

    How to enable server OSes (VMS or physical host computers) to connect and LUN iSCSI mount without compromising the safety of our ESX host?  We have a few Microsoft servers that need to use iSCSI initiators at Mount MON for MSCS.   We cannot use the ESX initiators because VMware doesn't support iSCSI to virtual storage with MSCS.  We have already read all the documentation and spoke with VMware support, so we know that our only option is to use the iSCSI initiators in Microsoft servers to connect to the LUN.

    Our concern is security.  If we let the servers use their iSCSI initiators to connect to the San, then they also won't have access to our service and the vkernels via the iSCSI network console?  ESX requires that you have a port the service console and the port of vkernel on the iSCSI network for each ESX box that you want to use the ESX initiator for.  We struggle to understand how to connect any machine (virtual or physical) to the iSCSI network to mount LUN without exposing our service and vkernels consoles.  I know that the best practice is to remove this VMs network for this exact reason, but of course many organizations also have physical servers (UNIX, Windows) who need to access their iSCSI SAN.  How people treat this?  How much of a security problem is it?  Is there a way to secure the service console and vkernel ports while allowing host ESX - no access to the SAN?  I know that many of you are facing this exact in your organizations situation, please help.  Obviously, it is not supposed that nobody uses their SAN iSCSI for anything else except for the ESX host.  I thank very you much.

    James

    Hello

    Check out this blog

    Use of firewall is certainly a step in the right direction for that. If you can't have separate iSCSI networks, then you will need to isolate nodes NON-ESX/VCB iSCSI using other mechanisms. I would certainly opt for firewalls or reduce the redundancy to just 2 network-by-network cards and not 4 to a single network.

    Someone at - it any other suggestions? Surely many ESX users share their iSCSI SAN with a lot of different systems and operating systems. Thanks again.

    They do, but they do not secure their networks for their VMs ESX iSCSI / other physical systems. You have asked a very important question and it's how to connect to iSCSI SAN without compromising safety. If the options are currently:

    1. Physically isolate

    2. Isolate using firewall

    Given that ESX speaks in clear text and does not support IPsec for iSCSI, you have very limited options that are available to you. The firewall you use and charge iSCSI, you send through it will determine if there is no latency. Yes its a cost extra, but if it is an independent network switches/ports/etc.

    Best regards
    Edward L. Haletky
    VMware communities user moderator, VMware vExpert 2009
    ====
    Author of the book ' VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.
    Blue gears and SearchVMware Pro items - top of page links of security virtualization - Security Virtualization Round Table Podcast

  • Add the host to the cluster vmware and SAN equilogic

    Hello...

    I will add 2 new for our cluster vmware vsphere host... I have not done this before, but think that I got the hang of it...

    But one thing that I am uncertain the San connectivity, is it just to create the map of iscsi on the vsphere host software and then add the adapters iqn name to access the San volumes page and rescan for the accessible volumes in the vmware host?

    That's about all.   Reported Tech on how to do so expressly.

    en.community.dell.com/.../TR1075-Configure-iSCSI-Connectivity-with-VMware-vSphere-5.pdf

    TR1091 shows how to configure VMware ESXi for best practices with storage EQL.

    en.Community.Dell.com/.../Download

    In my environment I use CHAP credentials for clusters of ESXi.  In this way a specific set of ESXi nodes use the CHAP username/password to access EQL volumes.  Advantage is when you add a new node, you only need to provide the name of user and password c.  You will not have to change anything on the side of EQL to add/remove a node.

    Kind regards

  • Impossible to create a network/how to connect to openstack-client CLI

    Hello

    According to the video 'VMware integrated OpenStack - adding networks - YouTube', it shows how to create a network through CLI openstack-client.

    While, I'm new to openstack and don't know how to connect to the CLI client at all.

    I could only try to create a network in the GUI. Here is my configuration:

    1.PNG

    It looks great, isn't it? However, I get:

    1.PNG

    Configure anything wrongly? BTW, can someone tell me how to access the CLI openstack-client as the video.

    Here is something you can try.

    If you are using DVS based network, you must enter "dvs" in the section "physical network.

    If you are using NSXV, then you can leave the Network Physics field empty, otherwise you must ensure that you enter a valid dvs moref id.

    For most cases, if you use NSXV, you can simply create network tenent in the project view (then NSXV will take care of it for you).

    Anyway, if you want to use cli, here are the steps.

    1 > connect to the administration server

    2 > ssh-i /home/viouser/.ssh/id_rsa viouser@controller01

    3 > sudo knew.

    4 > source cloudadmin.rc

    Then, you can use the cli freelly.

    Kind regards

    Yixing.

  • How to connect to the server pwercli RS?

    Hello

    I am trying to connect to the server of Powercli SRM but get error below.

    PowerCLI D:\Scripts > Connect-SrmServer srmservername

    Connect SrmServer: unable to connect to the remote server

    On line: 1 char: 18

    + Connect SrmServer < < < < srmservername

    + CategoryInfo: NotSpecified: (:)) [connect-SrmServer], WebExcept)

    ion

    + FullyQualifiedErrorId: System.Net.WebException, VMware.VimAutomation.ViC

    ore.Cmdlets.Commands.Srm.ConnectSrmServer

    PowerCLI D:\Scripts >

    Could you please help me to know how to connect?

    solved, it was the blocked 9007 port on the firewall. When I checked the above error again, I found that port 9007 is used.

    Thanks for all the help

  • How to restart vmware-vpxa using vMA 4.1

    I would like to know how to restart vmware-vpxa on an ESXi host using the vMA 4.1

    Currently I do with PowerCLI procedure

    SE connect-VIServer "hostname".
    $vpx = get-VMHostService | where {$_.} Key - eq "vmware-vpxa"}
    Restart-VMHostService $vpx - confirm

    But do not know how to do it using the vMA

    By default, there is no canned scripts/utilities to restart some services found on an ESX or ESXi host, but using the vSphere API, you can as in PowerCLI.

    Here's a vSphere SDK for Perl script that does exactly cela and works on vMA - hostServiceManagement.pl

  • How to connect computer virtual machine host

    HI gurus,

    I have 2 internal hard drives in a PC. Primary (host) disc hard have win 2003 server and an SAP system, 2nd drive hard having (machine VMWARE) win server 2003 and another of SAP systems. I want to connect SAP through RFC systems. How to connect the 2 devices? What are all the steps needed to connect these 2 machines and 2 SAP systems? How to ensure that the connection has been established?

    Concerning

    Raja

    Your uses (host only) VMnet 1 and IP network address of the 192.168.174.0 network. Your host has the address of node of 192.168.174.1 in this network. You can see VMnet1 host IP configuration.

    To be able to get the two machines communicate with each other, the guest must have an IP address in the same network. You have two options here, where I would choose one to make sure that the address does not change in the future (better for SAP I think):

    1. assign a static IP address at the prompt.

    Go to your comments and change IP address of 200.200.200.20 to 192.168.174.2.

    2. use of VMWare DHCP Server service.

    By default, this service must be running. Go to theguest and choose DHCP in TCP/IP configuration. The client will automatically get an IP address of 192.168.174.0.

    Enter the following lines in the files 'hosts' of the two systems:

    192.168.174.1 ecc6.mycompany.com ecc6

    192.168.174.2 sapserver sapserver.mycompany.com

    Now try if the communication works: open a DOS window on the host computer, and run the command "ping 192.168.1.2. You should receive the prompt responses.

    Try to ping the host from the host by using 'ping 192.168.174.1' there.

    As long as this does not work, nothing else to Word the communications between two machines.

    If this works, you should be able to use shared folders using the names from the "hosts" file or IP addresses.

    For example:

    +
    ecc6\ +.

    +
    192.168.174.1\If you have found this information useful, please consider awarding points to 'Correct' or 'Useful' answers and answers. Thank you!!

  • How to connect my i phone 6 to 10 on my computer windows

    How to connect my I Phone 6-10 Windows on my computer

    An iPhone will pair not via Bluetooth to a computer (Mac or Windows) with the exception of hotspot and then only if your cell phone plan he supports. See below for more information. https://discussions.Apple.com/docs/doc-7722

  • How to connect to itunes for ipad airplay without using computer?

    HOW to CONNECT IPAD AIRPLAY to ITUNES WITHOUT the HELP of a FULL ❓l

    There is no need to shout. What you're trying to use AirPlay to stream content from your iPad to?

    Using AirPlay: How to use AirPlay on your iPhone, iPad or iPod touch - Apple Support.

    (I asked for your message to be moved to use iPad forum, where you have posted is for questions about the iTunes U app.)

  • How to connect new IMac to old IMac to transfer files?

    I need to plug my June 2010 IMac in a new IMac 2016 to transfer data.  What cable do I and what ports should I use to connect?

    Thank you.

    Gina

    You can do it with an Ethernet cable (and on two Macs Ethernet ports) and use file sharing.  You can also connect via WiFi, but the transfer speed will be slower.  If both Mac connected to the Internet via a common router, you already have a link between two Macs.  Here is information on file sharing

    How to connect with the file sharing on your Mac - Apple Support

    There is also an automated tool called Migration Wizard, if duties are not suitable for your task

    Move your content to a new Mac - Apple Support

  • How to connect a new MacBook in my time for the initial file transfer capsule

    How to connect a new MacBook to my existing time capsule to transfer files as part of the first implementation of my MacBook?

    You say that you have a new MacBook and that you have posted to the forum for the retina MacBook 12 "section, but your tag indicates that you have a MacBook Pro. Please specify.

  • How to connect a drive to a 2015 iMac firewire external

    How to connect an external drive firewire to an iMac of 2015 for use with time machine?

    See love at first sight to FireWire adapter

    Apple Thunderbolt cables and adapters - Apple Support

  • Want to 750-209: how to connect an old sound system to a new computer

    I wanted a new 750-209 and a former speaker of Cambridge Soundworks PCWorks 19th Point Surround 4 + under low voltage. There are 2 connector; Left and right who are article 3 (each take manages 3 drivers). The envy has 1 output. It seems that I need a derivation ending in female connectors.

    My question? How to connect the two? Is it still possible? I'd hate to have a decent sound system of junk. My needs are basic - just to be able to listen on AOL or YouTube.

    Any ideas on how to accomplsh my goal.

    Just to close this debate; unfortunaely the quick response has not responded to the problem. BestBuy has suggested that I try a composed of derivation of a shot and 2 containers. Finally, I got the system works 'after' discovery that the enormous power brick disliked the new arrangement of power when I replaced the old computer with the desire. I had to replace an adapter 3 - wat and consolidate the brick. A lot of noise to get her old system to work but now I have the choice of speakers or headphones driven by a hold on a HDMI monitor. All's well that ends well. Thanks for the interest.

  • How to connect two computers and LAN

    I can't get my toshiba to interface with my desktop computer or to connect to the internet via a CAT5.
    I tried everything I know.

    I'm not too sure about the LAN MAC? He just will not connect even if the device is functioning properly.

    Any ideas?

    Here are the instructions how can connect the two computers.

    -First of all, you will need to disable the firewall.
    -Then you need to set the same workgroup on both computers
    -in the Lan Card Properties-> Protocol TCP/IP settings, you must assign the IP address manually. That is, a computer must use the 192.186.50.1 ip address and the other computer must be set to 192.186.50.2.
    -MAC address is fixed and cannot be changed. Each LAN card uses unique mac address

    After these settings, you must restart the portable computers (computers)

    PS: I recommend Google for details and further instructions.

  • Satellite A200 - how to connect to the TV?

    Hi you.

    How to connect my laptop to the tv with a S - video Cable Media or VGA - RGB cable? I tried to connect by Fn + F5, but no signal goes out. If I use the VGA - RGB cable + something is comeing out on TV but its streaming.

    Kindly help me...

    Hello

    You can use two cables to connect your laptop to the TV. It s according to the interfaces on the laptop and the TV, but in both cases, it of the same:
    Connect the cable to the laptop and TV, turn on your TV and select the right channel, then turn on your laptop. After the clean boot procedure, you can switch between monitors with FN + F5.

    If you use S-Video cable make sure you are using the coding system good TV, e.g. PAL or NTSC.

    > If I use the VGA - RGB cable something's come out to TV but its streaming.
    What settings did you use (screen resolution, screen refresh rate, etc.).

Maybe you are looking for

  • If I can put a music file in which will start playing when the mail is opened

    I want to put a music file in the body of the email which will start playing when the emaii is opened please let mewhether it is possible in Thunderbird mailThank you

  • Cannot connect Bluray Internet

    Shows the signal from the router but cannot connect

  • ENVY dv6-7290ef: access drivers cannot page for my laptop

    My ENVY of pilots dv6-7290ef page does not load after clicking on this link: http://support.hp.com/fr-fr/product/HP-ENVY-dv6-Notebook-PC-series/5296055/model/5311795/drivers/ . Tried all other links, detected... HP, the product still does not not :/

  • Moving files to Kindle from my PC

    I just got an Ideapad and I want to spend my own Kindle files to the Ideapad. I can't see a Kindle folder when I open the Ideapad in Windows Explorer. All advice as to how I can access the Kindle folder to move the files?

  • Commercekit crashes

    This problem has increased and it is impossible to address accidents...  This can eliminate through the integrity of the system, allows you to delete indexing with the projector without indexing if that should be the causes of this crash kit of trade