Similar Questions

• How to create the MUCOW file in xml using Adobe Muse

  How to create the file MUCOW as xml using Adobe Muse .kindly give step tutorial or PDF... WHERE DO I CREATE MUCOW? No idea for me

  Just lucky to have this info to my favorites

  MuCow Documentation

  Muse Jam Sessions_105_ConfiguringMucows

• I could use an airport extreme to extend my wifi network

  I was able to connect the extreme of the Airport via an ethernet cable to my sky router and use it to improve the signal? If yes how I would go about setting up

  I was able to connect the extreme of the Airport via an ethernet cable to my sky router and use it to improve the signal?

  Yes, if you understand that the Ethernet cable must remain permanently connected at all times.

  If yes how I would go about setting up

  Locate the AirPort Extreme right in the middle of the remote Valley where you need more coverage of wireless signal

  Connect an Ethernet cable from one of the LAN ports on the router from sky on 'o' WAN port on the AirPort Extreme <-->

  Run the Apple installation "Wizard".

  Assign the same exact wireless network name that uses the heaven to the AirPort Extreme router

  Assign a name of device for AirPort Extreme

  Enter the exact same word of wireless that uses the sky router

  Enter the password to confirm

  Click next and wait a minute, while the installation wizard does it all for you

  Click done when you see the installation complete message

• Create alarm "Network redundancy lost" by the script?

  Hello:

  I'm trying to write a script that will create the alarm in order to monitor the redundancy of the lost network (I know manually there) on the host.

  I know how to create alarm for additional exhibit the ' basic' event (LucD - thank you for your help) and I know that I have for alarm 'Lost network redundancy' to use 'vprob.net.redundancy.lost' instead of 'EnteringMaintenanceModeEvent' (as in my example); but I still struggle to combine...

  Can someone help me please?

  Thank you

  qwert

  I don't have a particular script fantasy with the settings and all the rest, but I can show you the steps to filter alarms by name and remove the desired one.

  alarm #retrieve Manager

  $alarmManager = get-view-Id "AlarmManager-AlarmManager.

  #Get the entity that contains the alarm that you want to remove. I'll do it for a virtual machine

  $entityView = get-Vm-name MyVm | Get-View

  #get all MoRefs alarm

  $alarmMoRefList = $alarmManager.GetAlarm($entityView.MoRef)

  #Retrieve tha alarm views from the MoRefs

  $alarmViewList = $alarmMoRefList | foreach (Get-view $_)

  #Now filter the name alrams

  $alarmToDelete = $alarmViewList | where {$_.Info.Name - eq "AlarmToDelete"}

  #Finally remove alarms

  $alarmToDelete.RemoveAlarm)

  It shouldn't be hard to put this in a script or function reussable. If you have problems with this, I'll be happy to help you again!

• How to create the legend and graphic label using VBS

  Hello

  I scoured internet before that I resorted to my question here. I hope someone can answer my question.

  Using VBS, how can I create a legend of the channels used in the chart and the label of the axis in the chart? Thanks in advance!

  I managed to find a way to create labels...

  Call GraphObjOpen(D2AxisXObj(1))
          D2AxisXTxt = "@@ChnName(CurrChnNo)@@ [@@ChnDim(CurrChnNo)@@]" ' Defines the x-label
  Call GraphObjClose(D2AxisXObj(1))
  

  Now, to figure out how create the legend. If anyone can help me, it would be great.

  ... And now I feel like a fool outright.

  After scouring more, I managed to find what I need

  Call GraphObjOpen("2D-Axis1")
    '------------------- Swith legend on -------------------------------
    D2LEGDRAW        =1
  
    D2LEGTXTTYPE     ="Free text" ' "ChannelName" or other keywords
    D2LEGTXTFREE     ="My free legend"
  
  Call GraphObjClose("2D-Axis1")
  'redraw
  Call Picupdate()
  

• How to create new worksheet in excel without using report generation tools

  Hello

  Im trying to create a file with 8 spreadsheet excel. I am currently using scripture to the worksheet of the vi for that file. But how to create multiple worksheets in an excel file without using the report generation toolkit module of the OR?

  Concerning

  Jay

  Hello

  You can use the nodes property with the class selected as Activex Excel and create all the tools to Excel. See the attached example.

  Kind regards
  Constant

  (Bravo to give good answers, mark it as a Solution If your problem is resolved)

• How to create a list of button by using the names of a table

  Hi, I want to create an application that displays detailed information about something. for example, as the profile of the users. my application will read an xml response from the server that contains the list of the names of the users. How to create a list of buttons using the names and then each button that displays the name that can be pressed and displays detailed information about the name? I think that it is similar to the BBM app that displays a contact list of the user. Thank you very much

  Create a ButtonField as:

  ButtonField [] users_buttons = new ButtonField [number of users];

  Initialize the uasing dem:

  for (int i = 0; i)<>

  users_buttons [i] = new ButtonField ("user", Field.FIELD_HCENTER |) ButtonField.CONSUME_CLICK);

  Make dem clickable setchangeListener method of buttonField and Ooveride Navigation click to make a few operatoin by clicking on the specific button!

• How to create a shortcut on the desktop using Windows 8?

  I have Windows 8 System. How to create a shortcut to Word and Excel? I do not want on the task bar, I want them on my desk. Any help would be greatly appreciated.

  Thanks for the help!

  On Mon, 15 Sep 2014 16:34:30 + 0000, sjblume wrote:

  I have Windows 8 System. How to create a shortcut to Word and Excel? I do not want on the task bar, I want them on my desk. Any help would be greatly appreciated.

  Just swipe their EXEs on the desktop. When you release the mouse button
  keys, choose "Create shortcut here."

• How to create a header for my magazine using InDesign CC

  How to create a header that will be applied automatically to all of my pages in my magazine without having to type in one by one in a text box?

  1. Always work with the character and paragraph Style. Not even a single letter should not a paragraph Style. (I do not recommend to use the default style brackets!)
  2. Create a text variable based on your title or any text that you want to appear in the header.
  3. Do a text frame on the master and insert the text variable. Take care that this block of text (such as page numbers) are outside the margin, otherwise she paint the content of the page. Put the header (and the page number) borders on its own layer above any other. Align block text in the margin, so you can then apply different page settings and use the page layout setting.

  

• How to create A registration and Login Page using adobe muse?

  How to create a registration and login Help Page?

  Hello

  check this discussion

  Re: Can I create a login/password in the Muse for a HTML5 page or two?

• How to create an insert of traveler medori using indesign

  can someone help me.

  My page size should be 4.33 of 8.25.

  How to create a page of this size in indesign

  File > New > Document... and set the size of the page on these dimensions.

• How to create a form of free paths using script?

  Hello

  I want to create a form in which I add multiple points

  I try to use GraphicLine, but it adds no way point in this

  var myGraphicLine = myPage.graphicLines.add ();

  myGraphicLine.paths.item (0).pathPoints.item (0) .anchor = [72, 72];

  myGraphicLine.paths.item (0).pathPoints.item (1) .anchor = [72, 144];

  myGraphicLine.paths.add ();

  myGraphicLine.paths.item (1).pathPoints.item (0) .anchor = [72, 144];

  myGraphicLine.paths.item (1).pathPoints.item (1) .anchor = [90, 100];

  myGraphicLine.paths.add ();

  myGraphicLine.paths.item (1).pathPoints.item (0) .anchor = [90, 100];

  myGraphicLine.paths.item (1).pathPoints.item (1) .anchor = [110, 144];

  myGraphicLine.paths.add ();

  myGraphicLine.paths.item (1).pathPoints.item (0) .anchor = [110, 144];

  myGraphicLine.paths.item (1).pathPoints.item (1) .anchor = [144, 72];

  I want to create a W shape using script type.

  How to create a form of type free paths (like those drawn with pencil or pen tools) using js?

  
  

  Thank you

  This is because you create separate ways. Create just a first, and then add all the pathpoints.

  Do not forget that all first path you create comes with free first 2 points, so just move these in the position as shown above. Then add the new points to the same path, rather than create new ones (lines #4, #8, and #12 in my example).

• How to create RMA based on orders placed using api OE_ORDER_PUB

  Hello
  
  Can someone help me pls how to create an RMA based on the command using oe_order_pub.process_order APi.
  
  Thank you.

  Creating the RMA is very similar to creating a command. You must make sure that you have the correct order_type, line_type who is going to be the 'RETURN' (or 'MIXED') configuration category in the definition of transaction type.

  The API automatically create a reference on your RMA lines for command lines original, you must pass the following
  l_line_tbl (l_line_tbl. COUNTY) .return_reason_code: = 'BACK '; -Compulsory for RMA
  l_line_tbl (l_line_tbl. COUNTY) .reference_line_id: = v_ref_line_id; -Original order line_id
  l_line_tbl (l_line_tbl. COUNTY) .reference_header_id: = v_ref_header_id; -Original order header_id
  l_line_tbl (l_line_tbl. COUNTY) .return_context: = 'ORDER ';
  l_line_tbl (l_line_tbl. COUNTY) .return_attribute1: = v_ref_header_id; -Original order header_id
  l_line_tbl (l_line_tbl. COUNTY) .return_attribute2: = v_ref_line_id; -Original order line_id

  Once the RAM is created, query the order and go to the lines > tab returns. You can see the original order number and line number.
  Thank you
  Gopal

• Why can't I use my Airport Extreme routers to extend my Google fiber network?

  I had waited for a long time, and finally got Google fiber installed at my house this afternoon.  I had been so excited and had everything for my home network mapped out.

  I've never used router Wi - Fi an ISP, but I read that so many good things about the fiber of Google box Wi - Fi I had planned to make the core of my Wi - Fi network home.  The plan was to have the Google through my home box.

  I have two base stations Airport Extreme AC I used with my old set up with Time Warner.  My plan was to use to extend my Google Wi - Fi network with a floor and one on the ground floor. Unfortunately, I can not understand how to get there.

  I did a hard reset on two of my Airport Extreme routers and went to set them up as extensions, but I can't do it.  I have open Airport utility, select my device, choose 'Other Options', select 'Add to an existing network' and click Next...  Each time, my only option is to create a new network.

  Does anyone know a way around this?  I would really like to be able to have a base station wireless AC in every room of my house.  I also need the Airport Extreme routers set up somewhere in the chain so I can continue to do my wireless Time Machine backups.  Any tips?  I am currently very frustrated.

  Thanks in advance for any help!

  -Brian

  Unfortunately, Apple routers will not be able to extend wireless signal of a 3rd party router. Or, another way of saying the same thing, is that routers Apple will extend only wireless signal from another router from Apple.

  If you could install another Apple router near the Google router and connect the Apple router using an Ethernet cable to the router fiber, and configure the router from Apple provides wireless... then... other airports will be able to extend the signal of the "main" Apple router

  You can use the fiber for a second wireless network or comments... or... If you need another network, there is probably a way to disable the wireless router fiber.

  Another option... If possible... would be to run both of your Apple routers Ethernet cables to the router of fiber. Then, Apple routers can be configured to extend the network of fiber like that.  Note that Ethernet cables should be left in place permanently with this option.

• How to configure WRT54G as a follow-up to my Airport extreme "n".

  I bought a WRT54G version 1 less than 6 months ago.

  Last week I got a Time Capsule from Apple with Airport Extreme 802.11n.

  As the Time Capsule AE "n" will be faster,

  I would use it rather than the main router.

  But how do the WRT54G an extension

  EI?

  basically is there a way I can configure two routers to work

  together and make the best of each?

  Thanks in advance

  Ignore the saber_tooth. It is just repeat everything. If you have a WRT54G web interface is something like this. You have to change the next radio button to disable the DHCP server on the WRT to the ' DHCP server: "leave"Enabled"to"disabled. "

  On the same page, you will also need to change the "local IP address". The default is 192.168.1.1. You must change this IP address to an available inside the Apple LAN address. The LAN on the most convenient airport is set up under the network tab of the Airport utility (at least on Windows version). The standard is to "distribute IP addresses" and "share a single IP address (using DHCP and NAT)" and to use the addressing 10.0.1.1/24.

  You can also view this information on Windows, in a command prompt window by entering "ipconfig". The interesting information is the IP address on the connection to the local network, the subnet mask and the default gateway. On a Mac, type "ifconfig" in a Terminal. Search the en0 interface, which should display the IP address after "inet" and the network mask. You will find the entry door with "netstat - rn". Locate the line of destination 'by default'. It shows the door entry in the second column.

  The subnet mask or network mask is usually 255.255.255.0 or 0xffffff00. With this subnet mask, all IP addresses with the same three digits belong to the same subnet. If you have an IP 10.0.1.123 with subnet mask 255.255.255.0 IP address 10.0.1.1 - 254 belong to the subnet. All IP addresses would be possible. Of course, you can not choose the IP address of the gateway (Airport). I don't know what IP address the airport itself uses by default. If you have any doubts, after the IP address, gateway address and subnet mask that you found on a computer that is connected to the Airport (i.e. The WRT not connected anywhere).