How to configure WRT54G as a follow-up to my Airport extreme "n".

Similar Questions

• How to extend a WiFi router network not Apple using Airport Extreme and Express?

  My cable ISP company just gave me a new modem/router - a DG of Arris - 2470. For the last two years I used a cable modem independent older with a connected Airport Extreme (both located on the ground floor) and an Airport Express station on the floor as an Extender. I was very happy with the power of the signal around the House.

  Since his arrival to the Arris router my signal has become very low to the floor. I would use my two Apple devices to extend/boost my network, but do not know how to do this.

  Thank you!

  Basically, you have two options:

  1. (Best overall performance of the network) Connect the extreme and Express on the Arris Ethernet gateway device and configure all for a traveling-type network. This would require an Ethernet connection between all routers that can be accomplished by either using Ethernet cable or the use of mains adapters.
  2. (The overall performance of the adequate network) Simply connect the extreme to the Arris Ethernet, then extend the extreme using the Express.

  Which of these do you prefer?

• How can I change the physical address associated with my Airport Extreme

  I moved, but when I look for devices by using find my iPhone devices connected to my Airport Extreme base station seem to be at my old location. How to upgrade the physical address associated with the Airport base station?

  To the best of my knowledge, there is no way for the user to do. Finally, the database of Apple will update. There is some anecdotal evidence of that having an iPhone connect to airport speeds the process.

• How to configure syslog on the following IPS module?

  Hi all

  We have modules IPS (ASA-SSM-10) which is installed in the firewall Cisco ASA (5520) and I want to integrate the server RSA Envision logs management module. Please confirm whether these can be integrated into Envision and how? I am able to get logs of Cisco ASA by activating loggin on the box. I need to send the logs of this sensor.

  Here are the details of the module-

  Platform: ASA-SSM-10
  Build version: 7.0 (4) E4

  OS version: 2.4.30 - IDS-smp-bigphys
  Can someone advise me on this

  Kind regards

  Saurabh Srivastava

  Is the tool RSA supports the CETS events.

  If Yes, then it should be simple enough to pull events.

  https://supportforums.Cisco.com/docs/doc-12515

  Kind regards

  Sawan Gupta

• How to create a network redundant ISP failover using 2 Airport Extreme

  Hello friends,

  I have 2 different lines of rented ISP related to my Airport Extreme 2. Was curious to know if these 2 AEs can be interconnected somehow to create a network of ISP failover. Users on AE 1 traffic would be transparent reassigned to the AE 2 and vice versa, if corresponding ISP fails. When the access provider is in place, they will return to their AE in elementary school.

  Thank you.

  Not without a smart dual wan router. That is to say done good load sharing.

  Extreme is about as simple a router you can find... He has the absolute minimum of functionality.

  Users on AE 1 traffic would be reassigned transparent to the AE 2 and vice versa

  You can do this by using some manual intervention... a simple change of entry door is usually sufficient.

• How to connect printer 2.4 Ghz band dual band Airport Extreme?

  I need a new printer connect to my Imac running OS 10.7.5 wirelessly.  My router is multiband Airport Extreme.  Most printers seem to does not support multi-band wireless;  they can't stand the 2.4 Ghz band.  Is there some document printers (I need scanning and copy also) which will be easily connected to the Airport Extreme multi-band, or is it possible I can put the Airport Extreme for a printer would only watch the band 2.4 Ghz?

  I found something on Google that says wireless devices should be filled, by disabling the Wlan partition.  I don't know what that means.   Another article said I could name the SSID separately and connect the printer to the 2.4 Ghz band.  Even when I don't know what that means.    Can you help me?  I do not know the printer Canon MG 5720 I bought does not work and I need to just throw it out.  I want to not to make another mistake.

  Thanks if anyone can help.

  On your Mac...

  Open Finder > Applications > utilities > AirPort Utility

  Click on the image of The AirPort Extreme

  Click Edit in the window that appears

  

  Click on the Wireless tab at the top of the next window

  Click on the button Options Wireless at the bottom of the next window

  Click to enter a check mark in the name of 5 GHz box

  Click Save

  
  

  
  

  Click Update at the bottom right of the next window and give the airport a minute full for restart

  The name of your normal wireless network is now a 2.4 GHz signal only.  The other wireless network has "5 GHz" appended to the name, so it's 5 GHz network

  Connect the printer to the 2.4 GHz network

  The name of '5 GHz' added now is the network of 5 GHz. connect devices in this band for a faster connection.

• Wifi configuration with Airport Extreme (A1143), iMac (El Capitan) running. Need of a direction.

  I recently moved to a City University and living in a housing facility run by the University. It's got broadband by Comcast for free with the room. I plugged all the necessary equipment (modem and cable) to the iMac and the internet works well for a week now.

  Now I want Wifi for the apartment. I decided to dust off my old 1st or 2nd Gen extreme base station Airport. I read that it can still work with El Capitan, so I went and tried to install it. First of all, I updated the firmware and connected the appropriate cables. Everything seemed to go in the direction of the work, but I hit a bump on the road. Wifi works for the iMac. I unplugged the ethernet cable and it's receiving internet, but I tried to get my iPad Wifi and smart phone and it doesn't seem to work. I used the good passwords etc. Nothing.

  I found it odd that I get Wifi to my iMac, although the Airport Extreme light is orange. Normally, it should be green. Of course, I don't use this thing in forever and actually don't think it would work, but so far the iMac becomes Wifi, but aren't the other devices and auburn is turned on. So here's a screenshot of what I see in the Airport utility.

  Can anyone help or point me to the right direction? Also it has to do with the campus of the internet, I'm getting?

  The attached picture shows it's getting to the internet via wifi (not plugged into the modem) but he doesn't seem to get wifi on my other devices in the apartment. The Airport base station we connected directly to the Modem. I also followed the steps of my iMac had originally planned to make it work and it did, but only for the iMac. I expect the unit to green thereafter but he did not. What gives?

  

  The A1143 was introduced in January 2007 and arrested in March 2009, so the model you have is at least 7 years and older, and as much as 9 + depending on when the product has been implemented.

  The average lifetime of a router designed for home use is about 5 years, so we're not sure how much time and effort you want to invest in AirPort Extreme you have there.

  Frankly, it is remarkable that the product works for the iMac, because status messages indicate that you have an Internet connection.  We cannot explain this one.

  We also don't know if amber on the most convenient airport is flashing, or remains Orange fixed. Can clarify you on this, please?

  If you want to try to start over again and set up the AirPort Extreme, the first bit of information that we need is the number of brand and model of your modem.  We don't need a serial number, only the manufacturer name and number for the modem to the model.

  We will try to help, but who can give no assurance that we will be able to get things working for you.

• How can I configure my Airport Extreme in Bridge mode (use the 3rd party router)?

  Data sheet:

  Airport Extreme - v 7.7.7

  Luma Surround Wifi 8

  I recently bought a wifi (luminance) surround system.  It comes with 3 routers that you place around your home.  Unfortunately I still have stains died in my house I'm looking to add my Airport Extreme (AE) to Luma network.  Is it as simple as plug the AE to the network (via Ethernet) and the bridge mode selection in the configuration of EI?

  I can see the AE of my iMac, and it is green.  How do you know that actually extend the wifi of my router Luma range?

  I searched the forum and all messages dealing with this are several years old.

  Thanks for your time...

  Basically, you want to create a mobile network with your Luma and AirPort Extreme routers. As you said, the extreme would need to be connected to the luminance by Ethernet and reconfigured as a bridge.

  In addition, the following are also required on the extreme:

  • Wireless mode: create a wireless network
  • The network name must be the same as that used by the Luma.
  • The type of wireless security and the password must match that of the luminance as well.

  To 'know' that the extreme extends the network of Luma, simply consult the BSSID value in the drop-down of OS X Wi - Fi. It must match the ID of the airport on your base station. Note: You must hold down the option key before clicking on the icon of the free Wi - Fi connection.

• How to configure Firefox 4.01 to save all tabs when closing the browser?

  In the previous version 3.x.y to Firefox, when I closed the browser, he asked me if I wanted to save my open pages / tablets before closing. When I open the browser again, then it rebooted all previously open tabs / pages. In the version 4.01, before avant de fermer close the browser warns me that I'm closing multiple tabs, but when I restart the browser once again, it does not load the already open tabs. How to configure the browser to behave like the old version of 3.x.y, that is perfectly save all open tabs and load these new opening to restart the browser?

  Firefox stores now always the old session, and you can access it by going to the history menu and selecting "restore previous Session."

  If you always open the last set of tabs, another approach is the following:

  1. Click on the orange button Firefox, then select options to open the options window
  2. Go to the general Panel
  3. Change the setting "When Firefox starts" to "show my windows and tabs from last time '.

• Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

  I got a modem Comcast/Xfinity upgrade. Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

  Whenever you change the modem or modem/router on a network, AirPort Extreme will be reset to the default settings and then set it up again to work properly with the new modem. For this he would be...

  Turn on AirPort Extreme for a few minutes... If it is not already turned on

  Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds, then release it.

  Allow a minute for the AirPort Extreme restart to a slow, flashing amber light status

  Make sure that an Ethernet cable connects to one of the four LAN <-->Ethernet ports on the modem/router on port WAN "O" on AirPort Extreme

  To start the Setup program, click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station

  Just below that, click directly on the AirPort Extreme and then follow the prompts for configuration "Wizard".

  When you configure AirPort Extreme once again, you can use the same wireless network name and the same password that you used with AirPort Extreme with the 'old' modem, if you wish, or use a new wireless network name and password

• How to configure my grandchild as a user on my computer?

  How to configure my grandchild as a user on my computer?

  Hello
  What version of the operating system is installed on your computer?
  What version of the operating system Windows am I running?
  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running
  You can follow the procedure in the article to create a new user account.
  Create a user account
  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account
  See also:
  What is an administrator account?
  http://Windows.Microsoft.com/en-us/Windows7/what-is-an-administrator-account
  What is a standard user account?
  http://Windows.Microsoft.com/en-us/Windows7/what-is-a-standard-user-account

• How and where should I go to find out how to configure my joystick so I can use the joystick to use the flight simulation game that I bought from microsoft?

  I can't find out how to configure my joy (attack3) stick to play Flight Simulator. I don't want to use the keyboard on my computer to steal the game... Where can I find the instructions on how to configure and use the joystick?

  Hello

  1. what happens when you connect the joy stick?

  2. do you get an error message?

  3. what version of Windows are you using?

  Perform the steps mentioned below and check if that helps:

  Step 1:

  Flight Simulator x: using a gamepad

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=16624

  Step 2:
  Usually, vista Windows 7 will find and automatically install the necessary drivers when you plug your game controller into your computer.

  (a) connect the joystick to the USB port via the adapter.

  (b) see if it is detected.

  (c) Windows should recognize the new hardware and set in place to work properly.

  If this isn't the case, install the relevant drivers for gamepad for the manufacturers Web site.

  Step 3:

  I suggest the following steps and check for the device.

  1. in Control Panel, open game controllers. To do this, use one of the following methods:

  a. click Start, typejoy.cpl in the Search box and press ENTER.

  2. click on your game controller, and then click Properties.

  3. on the Test tab, test the game controller to verify functionality.

  Here is the link:

  http://support.Microsoft.com/kb/831361

  I hope this helps.

• How to configure it so I have to put a password before signing?

  Original title: password computer

  I just bought my computer and when I go it does not ask for a password.  How to configure it so I have to put a password before signing?

  Hello
   
  What operating system are you using on your computer?
   
  Please follow the instructions from the link below and check if they will help you.
  Protect your computer with a password: http://windows.microsoft.com/en-US/windows7/Protect-your-computer-with-a-password

• How to configure ICS in network wired (Ethernet LAN) mixed (some XP some 7 64bits)

  We have an ethernet network.  A high speed printer.  Two towers XP (wireless).  A windows7 PC.  Currently, the windows7 pc is a laptop which has wireless capability.  However, we have NOT a wireless router. So don't give me responses bulletins on wireless connectivity.

  We use Internet connection sharing.  Somehow it just stopped working.  Do not know whether to blame a windows update or what.  We have probably messed up the worst configuration still try to get it working again. So I think that we must all start over and set up from ground zero.

  There is a technical bulletin, with simple (for beginners) instructions on how to configure ICS in a mixed network?  The instructions must be combined with the following configuration:

  Our host PC is XP.  We cannot change that, then give me all solutions where the pc windows7 is the host

  A customer is XP.

  A customer is windows7.

  We don't need to share files, just the printer.

  Hello

  The question you posted would be better suited in the technet Forums social. I recommend you to send your request in the below link:

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• How to configure outlook express for hotmail = Icannot sending spare part.

  I had to have a laptop but have a problem with it. Hope someone can help.

  I can send emails via hotmail, no problem. But when I try to send attachments the recipient receives an error message saying: could not read.

  When I tried to configure hotmail/outlook, asked me for some program codes | don't have no or understand.

  I'm a newbie to computer jargon. Please help if you can - many thanks.

  Hi Malcolm,

  1. What is the file format of the attachments that you send?

  2. What is the exact error message when you try to configure Outlook Express with your Hotmail account?

  3. are you having the same problem with other accounts?

  4 program are. which codes you referring?

  To open the attachments, the recipient must have the software file installed in the computer. Without the software, recipient may not be able to open the files.

  To set up Outlook Express, I suggest you go through the following articles of the KB.

  How to configure Outlook Express to use a Hotmail account

  http://support.Microsoft.com/kb/220852

  How to configure Outlook Express 6.0 for Internet mail

  http://support.Microsoft.com/kb/171163

  If the problem is only with Hotmail, then I suggest you to ask your question in the Forums of Hotmail.

  http://answers.Microsoft.com/en-us/windowslive/Forum/Hotmail