How to install the bluetooth adapter to 4.0 on my HP Pavilion p6-2304eb trust

Similar Questions

• ESXI how to install the network adapter driver

  Hi all:

  My ESXI5.5 has been installed, but find that the network card can not be identified, how to install the network adapter driver.

  Thank you very much

  Hello

  Follow the VMware KB for the installation of the NIC driver, hope it helps.

  VMware KB: Cards not detected on a host ESX ESXi network

• How to install the Bluetooth Module for Tecra S1

  Hello
  I have an old model S1 - PT831E-1DCEE-GR - and you want to install a Bluetooth (PA3121U-1BTM model?), but where should it be mounted?

  Kind regards

  Ulf

  Hello

  I think that on the Tecra S1 Bluetooth is optional.
  So on some laptops the BT has been installed on some not but I think that it should be possible to upgrade the unit with the BT module. (I hope ;))

  To my knowledge, the BT module must be installed in the place under the keyboard.
  But if you have no experience in these procedures you should t remove or install anything!

  The BT card must be placed above the keyboard area.
  To remove or to install the Bluetooth card, you must:
  1. remove the two white flat head screws.
  2 unplug the cable to antenna with the tweezers.
  3. disconnect the cards-SUMI (flat cables) on the system board.
  4 (remove the Bluetooth card) or (install the Bluetooth card)

  Be careful. But as I said above, usually it should be installed by a technician because the guys have more experience... you know

• How to install the Bluetooth firmware

  The communication between the software and the hardware blootooth is disturbed - I this before behhavior and it was corrected after an update to the bluetooth firmware (in a new version of OS X).

  So now I want to selectively reinstall the firmware of the internal bluetooth, as right now the message I get is: bluetooth is not available, and the bluetooth Control Panel is missing in system preferences.

  can someone give me a link?

  Kind regards

  Rob Tito

  What Mac model and what BT card is installed?

  What is the original install card BT?

  Have you tried reinstalling the BT card?

  Have you tried booting in safe mode?

  See if BT works OK on a new installation of Mac OS x? How to install OSX on another drive for testing purposes.

• Qosmio F20: How to install the bluetooth card?

  Hello

  Can you help me please? I ordered a few weeks there is a usb bluetooth but on the phone, the seller told me that the version I ordered has been replaced by a PA3477U new 28TM but it's a bluetooth card and I don't know how to install it. Anyboby help me?

  Thanks in advance
  Sisi

  Hello Sisi

  Can you please tell us what F20 you exactly (F20 - xxx)?

• Satellite A200 - how to install the bluetooth software?

  I got this laptop Satellite A200 of Australia. Recently, he had sum probs, so I restored it 2 factory settings using the backup option by pressing the 0 key... but later, I tried 2 find its Bluetooth software but I have strength c it doesn't matter where... anyone know how to install it or where it is located on the computer laptop d.
  Thank you

  Hmm. are you sure your laptop was equipped with an internal BT module?
  To my knowledge, not any of the A200 series support the BT

  However, you ask the BT (pilot) software.

  Here you are:
  http://APS2.toshiba-tro.de/Bluetooth/

  It is a Toshiba BT portal. You will find the latest version of the BT software.

• How to install the Bluetooth PAN, to share the Internet between Windows 7 PC and Samsung phone?

  Hello!
  I'm trying to connect my phone Samsung Galaxy Ace to my Windows 7 PC via Bluetooth and to set up a pan when my phone is connected via Bluetooth, it will appear in devices and printers, but when I open Bluetooth Personal Area Network, it is not at all. How can I configure a PAN which allows to share the internet connection from my PC to my phone?

  Original title: unable to connect to the Bluetooth device in Personal Area Network

  Hello
   
  Contact the support of Samsung for the support team.
  http://www.Samsung.com/us/support/
  
  
  Kind regards.

• How to install a Bluetooth Driver in box on new hardware in Windows 7

  Hi all

  I want to use Microsoft provided integrated Bluetooth driver.

  I have my new Bluetooth hardware.

  In Device Manager, I selected generic Bluetooth adapter driver for the hardware.

  It shows Bluetooth generic adapter not Microsoft Bluetooth Enumerator.

  How can I start Microsoft Bluetooth Enumerator, to work with my hardware. ?

  Give me information on that.

  Hello, NGO,

  Thanks for posting in the Microsoft Community.

  Microsoft Bluetooth Enumerator comes into play when you connect the Bluetooth device unless the coach in which Windows 7 automatically installs the driver.

  After that Windows detects the Bluetooth device, it is controlled by Microsoft Bluetooth Enumerator and not the third-party driver.

  Here's a way to install the bluetooth driver released by the manufacturer to resolve the problem.

  Method 1: Rename the Bth.inf file

  Rename the %WINDIR%\inf\Bth.inf to Bth.bak before you install or reinstall the battery or third device.

  To rename the file, follow these steps:

  1. click on Start, click run, type %windir%\inf in the Open box, and then click OK.

  2 right-click Bth.infand then click Rename.

  3 Rename Bth.inf to Bth.bak, and press ENTER.

  Method 2: Install the bluetooth driver

   

  1. click on Start, type devmgmt.msc in the Open box and then press on Enter.

  2. Locate the unit.

  3. right click on the device, then click on Update driver.

  4. follow the steps that appear on the screen in the Hardware Update Wizard to specify your own driver for the Bluetooth device.

  This should be it.

  You can also view the Microsoft Help article and check.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps. Just reply to us with the State of the question.

  Thank you.

• Satellite P750: Impossible to install the Bluetooth Stack on Windows 7 (x 64) driver

  Hello.

  I own a * Satellite P750-02 t * (part No. * PSAY3A - T 02 001 *).

  In the order I did:

  (1) I formatted the HARD drive and reinstalled the operating system of * Windows 7 x 64 Ultimate SP1 *.

  Then I downloaded * ONLY the BIOS and drivers * of [his downloads page | http://www.mytoshiba.com.au/support/computers/satellite/p750/psay3a-02t001/download?os=25]:

  (2) I've updated the BIOS for * v1.90* (the laptop came with v1.80)

  (3) I have installed all drivers:
  -LAN and WiFi
  -Chipset Intel latest (available)
  -all video drivers (NVIDIA Graphics, Intel HD Graphics and Intel HDMI)
  -Card reader
  -Realtek HD Audio (later)
  -Synaptics Touchpad
  -USB3.0
  -IR
  TV tuner
  However, I * cannot install Bluetooth driver (v8.00.06 (T) *)...

  When I run the installation program of the [aforementioned page | http://www.mytoshiba.com.au/support/computers/satellite/p750/psay3a-02t001/download?os=25] it detects partially *'Bluetooth USB Controller-10 TOSHIBA'* (USB\VID_0930 & PID_0215 & REV_001)
  and then the installation freezes simply displaying + "install the Bluetooth driver. Please wait +.' and stay like that forever...

  I also tried to download a driver [another location | http://aps2.toshiba-tro.de/bluetooth/index.php?page=download-toshiba] for laptops TOSHIBA - v8.00.02 (T):
  and followed installation instructions displayed under "Details".
  but he had the same result: the installer simply crashes...

  Install fix (* KB978258 *) recommended it did not work either - the message "+ update is not applicable to your computer +" appears.
  And I understand why - this fix is [already included: http://download.microsoft.com/download/E/B/A/EBA55FE2-373A-4351-9346-6D762B79AA69/Updates%20in%20Win7%20and%20WS08R2%20SP1.xls] in Service Pack 1 for MS Windows 7.

  I spent hours searching the Internet for a solution. Although there are some similar cases, none of the recommendations actually worked. I tried to install:
  -WiFi driver before installing the Bluetooth (someone suggested that these two are parts of the same card);
  -Repeat Mode Setup without failure;
  -* Toshiba value added package * hoping that somehow these tools will kick in.
  Nothing has worked...

  It is interesting to note that when, in the interests of experimentation, I tried to run installation for my generic Bluetooth adapter (using the driver [for non-TOSHIBA notebooks | http://aps2.toshiba-tro.de/bluetooth/index.php?page=download]) then everything runs smoothly!

  * Using connection Bluetooth on this laptop is absolutely crucial for TI
  I hope that I won't get back this beautiful laptop as I know that TOSHIBA is one of the best manufacturers and I am sure, that there is a solution to this problem.

  Thank you very much.
  Evgeny.

  Post edited by: cardiovascular disease
  specified on the use of another generic Bluetooth adapter with non-TOSHIBA driver

  You can use the key combination FN + F8 to toggle WLAN?
  You can also see BT symbol there?

  Before you begin installation battery BT try to activate BT module by using the FN + F8 key combination.

  Generally avoid some problem with it. Toshiba BT stack is tested on al models proposed by Toshiba and fireplace installation BT has, in my view, nothing to see what version of Win7 you use.

  Do not return this laptop. It has to do is just install drivers, tools and utilities. Please note: BT stack is included in the recovery image so BT must work.

  Also, I must say that OS installation of drivers, tools and utilities on Toshiba laptop must / should be installed in the correct order. Many tools can work only and must be installed on basic stuff that can be installed with other specific tools of Toshiba.

  Please send a few comments if this FN + F8 will work.

• How to identify a bluetooth adapter internal since an Interface Card by simply opening a laptop cover?

  How to identify a bluetooth adapter internal since an Interface Card by simply opening a laptop cover?

  Hello

  See if that helps

  How to fix a Bluetooth adapter internal

  http://www.laptoppartwholesale.com/eBlog/how-to-attach-an-internal-Bluetooth-adapter.html

  Installation of a wireless card internal

  http://www.laptoprepair101.com/laptop/2008/03/08/installing-internal-wireless-card-into-older-laptop/

• Impossible to install the Bluetooth software

  Hi all

  When I tried to install the latest version of the Bluetooth 12.0.0.3600 for my T430s software, the installation will stop at the end with a Chinese error message. I would like to attach a screenshot of the error message, but can't seem to find any possibility to attach on this site.

  So now I'm stuck with the driver that windows installs by default (12.0.0.10). Whenever I start the laptop, I get an error message btwapi.dll missing. There is no Bluetooth entry in ' Control Panel / programs and settings ", so I can't uninstall the old driver manually. A new habit to install (probably because the old is there and damaged.

  Someone has any suggestions how to solve this problem?

  Thank you very much

  Thanks for your comments. I finished setting up the laptop from scratch. The first thing I did after installing base was to update the Bluetooth drivers and it worked without problem. I suspect that the culprit was the ThinkPad Bluetooth Laser Mouse. When I updated the Bluetooth software before installing the Bluetooth mouse, I was able to update without problems.

• Installing the Bluetooth software

  Bluetooth Dongle v2.0
  error I get is: cyclic redundancy check data error check the computer recognizes the Blue tooth adapter, but does not accept the software or can not find any other soft dishes for her.

  Hi dennis47,

  The cyclic redundancy check error is a bit of mathematics used to ensure that your data is correct when transferred. It is a verification procedure that will quickly identify when the data has been corrupted. If you get this message, it means that the file is read by your PC or your software is corrupted.

  If you use a Bluetooth adapter installation DVD, it may be damaged or may have a lot of mistakes in this regard.

  I suggest that you check if the disc contains scratches or dirty on it and clean the surface with the useful of clean, dry cloth and try again.
  If the previous step fails then I would suggest that you visit the Bluetooth adapter manufacturer site, download and install the drivers for it.

  Set up a Bluetooth compatible device
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device
  If the steps above fail then I would suggest that you contact the manufacturer of the Bluetooth dongle for more support.

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• System crash when I install the bluetooth driver in windows 8.1

  HP Pavilion 15-e034tx

  When I install bluetooth driver in system failure windows 8.1 with this error "unhandled Thread Exception system.

  Bluetooth hardware ID: PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C & REV_00

  Sir where is Bluetooth for Windows 8.1 driver?

  can someone help me please?

  Hello everyone I found the solution to this problem of Bluetooth. First of all, I want to share the essue of Blutooth hand in windows 8.1.

  History is actually a bit interesting: Microsoft has fixed a bug in the rollup of November which exposed a bug previously hidden in Bluetooth drivers for Ralink/Mediatek, resulting in all the world with a fully-updated Windows 8.1 and Ralink bluetooth (very common in low price/low-end systems) to BSoD unless the bumps users to a system restore point before updates of November. So yes, there are sometimes dangers for fixing bugs.

  Basic requirements:

  1. all drivers for HP laptop, BIOS and windows 8.1 implemented to date with the latest updates.
  

  File Requirements:

  1 8.1 Windows file update kb2917488 - x 64 (download link)

  http://www.4shared.com/RAR/CP-Ov9Hv/blutooth_update_fix.html

  2. Ralink software Bluetooth driver (windows 8 or 8.1 Windows)

  Basic steps:

  First check windows update, download and install any updates. Also download and install the latest driver for windows 8.1

  Download file update 8.1 for Windows kb2917488 - x 64 in 4shared link. (File name: Bluetooth fix)

  kb2917488 - x 64 Windows 8.1 updated in.cab(cabinet file) If you need to know how to install the .cab file installation.

  The .cab file installation steps

  Open the administrator command prompt and run the following command to install and integrate the Archives of Cabinet:

  Pkgmgr/ip/m:.cab / quiet

  Or,

  start/wait pkgmgr/ip/m:.cab / quiet

  Replace with the path (location) for the file .cab and with the file name of the cab without parentheses. If the CAB file is in the current directory (same directory where the command is executed, the path can be ignored.

  Example: pkgmgr /ip /m:C:\Users\User update fix\windows8.1-kb2917488-x64_43f3b89601d407a00cbf87297ab1ddb0ba1c4619.cab/quiet

  (If you do not understand the method of installing the .cab file search for it on google)

  This command silently install the Windows kb2917488 8.1 update file - x 64 in your system... complete installing the automatic system successfully reboots (wait automatic reboot)

  Now you can install your old windows 8 Ralink Driver Bluetooth software or update the latest driver with HP Support Assistant in windows 8.1.

  (Note: install all the drivers to run as Administration) (Sorry for the bad English)

   

• How to install the plugin html on OS 10.11.6

  How to install the plugin html on OS 10.11.6

  For html5, you mean? Your browser must be able to show html5 without plugins.

  If something does not work for you, please explain what it is.

• How to install the latest version 5.1.1 ipad?

  How to install the latest version 5.1.1 ipad?

  If you have an iPad 1 (no cameras) may not be updated beyond IOS 5.1.1.