How to set up EA6500 so another router can be used as access point?

Similar Questions

• A DBA how to set permissions so that its users can submit to its form but do not have to execute queries or touch the database?

  Original title: InfoPath/SQL

  I am familiar with InfoPath, but I'm a DBA to a database on SQL server. The person created the infopath form and there users who can submit to the form, however, the only ones who can submit to the form are those who have access to SQL. A DBA how to set permissions so that its users can submit to its form, but do not have access to run queries or press my database. Thank you

  Ask the question in the SQL Server forums:
  http://social.msdn.Microsoft.com/forums/SQLServer/en-us/home?category=SQLServer

• Can I use as a point of access Wireless-G broadband router?

  I use a router broadband wireless Netgear as main router to the ground floor and connected to the internet. I connected an access point wireless of LinkSys (WAP54G) as a wireless Repeater. Same SSID however, I turned wide dissemination. My office upstairs, I have wifi internet access very well and remain connected indefinitely. However, shortly after connecting to the Office VPN (off-site), the connection drops-both internet and VPN! I ran a loooong cat5 to the office on the floor and when it is connected to WAN I remains connected to two connections indefinitely. I do not have another AP, but I do not have a router Wireless G (WRT - 54G). Can I use this router as an AP, the same SSID, but I noticed on previous posts I should reactivate broadcast on all devices and change the channel settings. I noticed, when I went into the Setup utility 192.168.1.1, I access my netgear router, how to enter the Linksys router?

  Thank you

  Ken

  Nothing beats an AP on the WRT mode. It's just connecting it via the main router LAN port, you can use the access point without going through the router within the WRT component.

  You will have to do exactly what I wrote. Don't change anything on the Netgear.

  1. disconnect your network WRT. Wire a single computer to a LAN of the WRT port.

  2. open the web interface of the WRT to http://192.168.1.1/ since the computer you plugged on the WRT.

  3. on the main change WRT configuration page the LAN IP of 192.168.1.1 to 192.168.1.2 and disable the DHCP server.

  4. save the settings. Unplug the computer.

  5. wire one of the LAN ports of the WRT to the Netgear. Do not use the internet port of the WRT!

  That's all. You don't change anything after that. It is the final configuration. You can now access the web interface Netgear http://192.168.1.1/ and the web interface WRT to http://192.168.1.2/

• How to set up VPN on the router via ASA5505 2811

  Hello everyone

  I apologize for the possible triviality of my question. The current configuration of our society considers appropriate for the edge, two ASA5505 below that are installed two routers configured with the CCME 2811 Express. When the two AS5505 is configured a VPN connection for the transmission of data in our network traffic. Given the presence of several public addresses available on our two sites, I was wondering if you could (and if so, how) to set up a VPN between two routers 2811, except that when existing data traffic, dedicated exclusively to the voice traffic. It give me a document that teach me how can I solve my problem?

  Thank you very much

  Damiano,

  If you want an IPsec VPN for only separate voice and termination traffic on routers, there are several possibilities. Especially if you have a spare IP addresses:

  IPsec VPN endpoints on the routers.

  GRE over IPsec routers ending (gives you that soften what and where can be routed, in particular, identify voice traffic)

  Termination of free WILL on the routers and unloading IPsec to ASAs. (Benefit of the foregoing + ASAs making encryption).

  There is no problem to close the tunnels through the ASA, the only warning is that even in the case of static NAT you should probably use NAT-Traversal.

  Marcin

• How to set up a Lan to Lan VPN without using your external IP address?

  I have two 28 subnets A & B.

  My PIX and ASA outside interface addresses are both in A subnet.

  I am in the middle of a migration of the PIX to ASA and need to use the PIX outside of the address of the interface on the ASA for the last two remaining lan to lan VPN.

  I do like that because the sellers of these virtual private networks to connect to are huge dinosaurs IT and the aaages to get their sh * t tri... This means that I have to pass the IP address to my ASA, so I can't sentence have change for a new IP peer.

  I tried to figure out how to set a specific my counterpart VPN IP address but I can't figure out how...

  I even physically connected a second ethernet port and tried to give a similar IP in the same range, which it says it is not possible to have both outside the IP addresses on the same subnet.

  Hello

  It is not possible to have an IP address "secondary" on the physics/logic interface of a Cisco firewall.

  And as you've noticed, you cannot configure the same subnet on 2 different interface either.

  We are talking about such a large configuration that you want to just migrate from completely to the ASA PIX and make a switch during a maintenance window?

  Couldn't you just pass the ASAs 'outside' IP address address to that on the PIX and move the ASAs 'outside' of the PIX? Or not the ASAs "outside" IP address already some configured related to what makes this impossible?

  -Jouni

• WRT600N advanced routing problems / use as Access Point and switch

  Firmware 1.01.36 build 4 The WRT600N is connected to an existing LAN and is really only used as a Wireless N access point. There is nothing plugged into the WAN port; only the LAN port. I have NAT disabled. All traffic from a client connected to the WRT600N wireless going very well for the gateway and the Internet router. The customer experience is very good. However, there are a few minor issues as follows.

  1] Setup > Advanced Routing tab has only the following options; to do this, * not * have a picker 'Mode '. NAT, static routing and dynamic routing (RIP).    IS this NORMAL, OR should HAVE a MODE (e.g. switch) AS REFERRED to IN THE HELP FILES?

  [2] even if a connection wireless or wired to the WRT600N works very well, the WRT600N himself is unable to connect to the internet. It cannot connect to NTP to set the time and I can't ping past the gateway router using the ping of the WRT600N diagnostic utility. I ping the gateway 192.168.1.4 port inside, but I can't use the diagnostic the WRT600N ping ping utility something beyond this gateway port. The routing of the WRT600N table is below. THE GATEWAY SHOULD NOT BE 192/168.1.4? HOWEVER THE WRT600N DON'T ME LETS NOT CHANGE IT.

  Destination LAN IP Subnet Mask gateway interface

  192.168.1.0 255.255.255.0 192.168.1.71 LAN & Wireless

  127.0.0.0 255.0.0.0 * LAN & Wireless

  Topic 1. Linksys, used to have a mode option to switch between the modes 'Bridge' and 'router '. The latest routers call it now better NAT power. Gateway mode means THAT NAT is enabled. Router mode means THAT NAT is disabled. The help files are probably a little bit over. But the option is still the same.

  Re 2. It's normal if you use it as only access point (i.e. do not use the WAN port). The router always takes into account that the internet connection via the WAN port, i.e. it will always use the default gateway on the WAN port. If nothing is connected to the WAN port on the router itself has no default gateway and therefore has no access to the internet. Generally, you are not able to establish the default route in either advanced routing page. It is a known limit of these routers if you do not use as a router.

• How to set a password for the router in mn 700?

  I have a MN-700 router and want to set a password so that other people can not access my connection. Can u please provide an astep step-by-step, instructions how to do it. Thank you.

  This is not a forum for the MN-700 router. You have to go to the manufacturer's Web site and look for the instructions or ask their support desk.

• How to set up WOL in a routed environment

  Hello

  We have a routed environment after switches Powerconnect 6224 and we wonder if it is possible to allow WOL requests on all the VLANS?

  We use the K2000, which enables WOL and we would like to use this feature.

  Wouter

  The solution, thanks to Daniel, was to add ip helper addresses

  helper-IP 10.10.10.10 address 7

  helper-IP 10.10.10.10 address 9

  Where 10.10.10.10 is the IP address of the box of K

• profile avatar: what is an avatar? How can I change? where are the avatars to select another? can I use a photo from my profile avatar?

  PROFILE OF COMMUNITY SUPPORT: I CLICKED ON EDIT AVATAR AND HE OPENED MY OFFICE LIST. WHERE CAN I FIND AVATARS POSSIBLE CHOICE. CAN I JUST USE ONE OF MY PHOTOS, IF SO HOW DO I DO THIS? I'M A BEGINNER, VERY, VERY, EVERY DETAIL IS SO NECESSARY FOR ME TO FOLLOW THE BREAD CRUMBS. ALL IN CAPITAL LETTERS: I AM NOT SHOUTING AT YOU, HAVE SOME PROBLEMS WITH LIGHT... A.

  FEB 09. 2013 16: 54. THANK YOU FOR YOUR HELP.

  Hello andyusfr, yes you can use an image or a photo as avatar, but don't forget "avatars" have low resolution, so it's a little hard to see all details.

  You can search in the search engines also for avatars.

  If you don't like an avatar, you can change to another, or to default (remove a link if poster on the page edit beside the new avatar profile.) If you click on it, which will restore the default avatar)

  Thank you

• How to set the time difference between each data when using keithley 2400 scanning

  Hello friends,

  I use scanning Keithley vi the extent of SCANNING and acquire vi. I want to measure the voltage for each step and a pause between each two data, so I need a delay between each I step.

  I'm a starter to use Labview, thank you very much for your answers.

  Perry

  As Dennis says, if you use the built-in scan function, you will need to consult the manual. See Section 10-16 (this is page 10 of article 16, only paragraphs not but 10, 16) for the manual Keithley 2400.

  The Keithley 24xx series has a speed of measurement in units called PLC (Power Line Cycles). The default speed is 1PLC, which means a measure is taken with each cycle of line 1 power supply or 1/60th of a second (16.67ms). 24XX can range from 0.01 PLC (all 0.16ms) 10 PLC (all 166.6ms). The faster you measure, the less accuracy you get.

  To programmatically set this value, the command is

  ENSe:CURRent:NPLCycles

  ENSe:VOLTage:NPLCycles

  Depending on what you are sensing and where is the number of controllers from 0.01 to 10.

  Another factor that will determine the time between data points is the cycle SDM. These are more complicated, look at your Keithley manual for more information. Look at article 6 and article 11 for more information.

  Note:

  PLC times are based on a cycle of 60 Hz US.

• How to set a master password, that I can use on my laptop to be used for all programs. I have a computer at home

  I don't remember all the different passwords to be used.

  I have a tablet on my desk to write all the information required to connect to the program.

  I hear that home count, I can set up a master password to be used for all programs.

  If possible can anyone give/suggest how to proceed.

  Instructions, I had to do was control + user account set up a master password.

  I have a Dell Inspiron runnung office 7 portable

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en/w7itprogeneral/threads

  I hope this helps.

• How to set the user name and password when you use the class for SOCKS5 Proxy?

  Hi all
  
  I use the proxy class for SOCKS5, so need to set the user name and password, I can't find where I put the value. If the API support.
  
  Thanks in advance!

  Exactly how to repeat the question five times ater, we told you the answer would erase anything? A: this isn't. This irritates just the hell out of people. Irritating the hell of those who's trying to help you is not rational behavior either.

  I have no idea on the support of third-party for transmission by proxy via NIO.

• How to set the Home Page of a newly-opened using the file tab > tab Menu?

  When I open a new tab, is there a way to set the home page for the new tab to use when it is open, or new tabs always open as blank pages?

  New tab homepage extension:
  
  https://addons.Mozilla.org/en-us/Firefox/addon/777

• How to remove a password from a router have not used in like 4 years should be able to delete the password or reset it if I can put something new on it

  I have not used in like 4 years must either be able to clear the password or reset it if I can put something new on it. try to get the password required to connect to the web on a new device and can not remember the password I want to erase the password he please someone help me!

  Is what kind of router? Most routers have a reset on the back of them, you'll need something like a paper clip or pen to press the button. Basically you hold down the button for like 10 seconds, and all the lights start flashing, when this happens, you can stop it by pressing the button. When everything goes back to normal, we must reset factory default mind. The default ip address is usually 192.168.0.1 or 192.168.1.1, the username is usually admin and the password is password. Sometimes these are the admin admin, or admin without password, or no username and admin or password for the password. However it may be something completely different. If you have the make and model, I can tell you with certainty what it is :D

• How to set the date of beginning of a calendar using an element

  Hello

  I have a calendar by using the SQL query:

  SELECT	(b)"NAME" | ' ' || b."NAME" "Agent."
  	a."DATE_ACTIVITE" 'day. '

  a."FICHE_ID".

  Of	PLUG a, b AGENT
  WHERE	a.AGENT_ID = b.AGENT_ID

  AND one. "' EQUIPE_ID ' like NVL (REPLACE (: P60_EQUIPE_ID,-, 1, NULL), '%')

  AND one. "" AGENT_ID "like NVL (REPLACE (: P60_AGENT_ID,-, 1, NULL), '%')

  ORDER OF "Agent".

  I would like the calendar to start at a date contained in an element: P61_DATE_ACTIVITE

  I tried to play with the element of apex: APEX$ NEW_START_DATE, by setting its value to the value of the element, but it has not given results.

  Do you have any suggestions?

  Thank you.

  Hi Chipniz

  I would update your code to be like this

  $(document).ready(function() {
  // Get Year and Month
  var year = 2015; /*year = 2015*/
  var month = 0;  /*month = 1 --> put it 1-1*/
  // Goto the date
  var d = new Date();
  d.setFullYear(year);
  d.setMonth(month);
      $('#CALENDAR_ID').fullCalendar('gotoDate', d);
  });
  

  Reference

  Re: Link column to the right calendar page

  I hope that solves your problem

  Concerning

  Mahmoud