How to set up WOL in a routed environment

Similar Questions

• How to set up VPN on the router via ASA5505 2811

  Hello everyone

  I apologize for the possible triviality of my question. The current configuration of our society considers appropriate for the edge, two ASA5505 below that are installed two routers configured with the CCME 2811 Express. When the two AS5505 is configured a VPN connection for the transmission of data in our network traffic. Given the presence of several public addresses available on our two sites, I was wondering if you could (and if so, how) to set up a VPN between two routers 2811, except that when existing data traffic, dedicated exclusively to the voice traffic. It give me a document that teach me how can I solve my problem?

  Thank you very much

  Damiano,

  If you want an IPsec VPN for only separate voice and termination traffic on routers, there are several possibilities. Especially if you have a spare IP addresses:

  IPsec VPN endpoints on the routers.

  GRE over IPsec routers ending (gives you that soften what and where can be routed, in particular, identify voice traffic)

  Termination of free WILL on the routers and unloading IPsec to ASAs. (Benefit of the foregoing + ASAs making encryption).

  There is no problem to close the tunnels through the ASA, the only warning is that even in the case of static NAT you should probably use NAT-Traversal.

  Marcin

• How to set a password for the router in mn 700?

  I have a MN-700 router and want to set a password so that other people can not access my connection. Can u please provide an astep step-by-step, instructions how to do it. Thank you.

  This is not a forum for the MN-700 router. You have to go to the manufacturer's Web site and look for the instructions or ask their support desk.

• How to set up EA6500 so another router can be used as access point?

  I have an EA6500 but successor getting wireless for individual room in my house.   I have an old DIR655 router that I want to connect wired to switch in this room, I want to use to extend the signal wirelessly to the same SSID.

  How to configure EA6500 and DIR655 for this?

  Help, please.  Thank you.

  Yes, you must reset your router Dlink as sabretooth suggested. If the Dlink IP address is 192.168.0.1, which differs from your EA6500 IP of 192.168.1.1, you can do a Lan to Wan set up.
  Moreover, you would be to see name/SSID wireless router since it still broadcasts a Wi - Fi signal.

• How to set up Time Machine via a HARD drive connected to the USB port on the router?

  Hi all

  I have an Arris Touchstone Data Gateway DG1670A/TW for my internet / wireless which was provided by my ISP.  There is a USB port at the back of the router and I was wondering if I could connect an external HARD drive to save the two Macbook Pro that I have in my house through Time Machine wireless?  If Yes, could someone provide me the details regarding how to set this up properly?

  I too, was thinking about making a 4 TB HARD drive - 2 and wanted to partition so that half of it would work for Time Machine and the other half I would be able to store photos that I take on my digital SLR and are in Lightroom.  Could this be a problem at all? I partition? or Time Machine just to use the available space and delete older backups to make room for additional photos?

  Thanks in advance for any help.

  A device third-party network attached storage (NAS) or a router is unsuitable for use with Time Machine.

  Apple has published a specification for network devices that works with Time Machine. No third party provider, AFAIK, does meet this specification.

  Apple does not endorse any device third-party network for use with Time Machine. See this support article.

  Network backup, use as destination an Apple Time Capsule or an external storage device connected to another Mac or a 802.11ac AirPort base station. Only 802.11ac base stations support time Machine, not older model.

• MN - 700 router worked for a while (over 3 years) without password. How to set a password? __

  MN - 700 router worked for a while (over 3 years) without password. How to set a password?

  MN - 700 router worked for a while (over 3 years) without password. How to set a password?

  This is a pretty old router, but documentation is still available from Microsoft:http://support.microsoft.com/kb/902461 the 'Guide' is more complete, but the "Base Station Configuration Guide" will explain how to configure the router.

  I guess what you mean by a "password" is the password for the wireless encryption (there is also a password that controls access to the router configuration utility). The following are the basic steps to configure wireless encryption (see the documentation for more details and screenshots):

  1. utility access to the router configuration, preferably with a computer connected to the router with an Ethernet cable (if you change your wireless security, the parameters using a computer connected to the router by wireless, the connection will be abandoned as soon as you click APPLY).  Open a web browser and type 192.168.2.1 in the browser address box.  If you have not changed the logon password, enter 'admin' (without the quotes, all lowercase).

  2. click on the "Security" link on the home page of the configuration tool, then "Wireless Security".

  3. Select the "niveau_chiffrement" in the combo box to "256-bit WPA - PSK (louder)" - unless all of your wireless devices are so old they don't support WEP (unusual for a wifi device years less than 5 or 6).

  4. in the box, type a password (between 8 and 63 characters), and then click 'apply '. at this point, you will be disconnected from the router (and the Internet) If you did the above changes using a computer connected to the router WiFi.   Write the password in a place where you don't forget.

  5. close router configuration utility.

  To set up your wireless computers:

  6. open network connections (start > run > ncpa.cpl > OK)

  7. right click on your wireless adapter icon and select Properties.

  8. click on the wireless networks tab

  9. make sure the box at the top next to "use Windows to configure my wireless."

  10. in the list of "Preferred networks", select the entry to your router (your network name), click on 'delete '.  [This deletes the entry from your wireless network WITHOUT a password, so that you will be able to add an entry for a network with the same name WITH a password.]

  11. click on the view wireless networks"" button.

  12. the name of your network should appear in the list of wireless networks.  Select it and click "connect". When you are prompted for the password, enter the WPA password set in the router configuration.

  13. open a web browser and confirm that you can access the Internet.

• How to set the printer wireless ad Hoc mode to CP1025nw with automatic stop is off? IE never automatic.

  How to set the printer wireless ad Hoc mode to CP1025nw with automatic stop is off? IE never automatic.

  Thank you very much for your help, if necessary.

  Quite a few questions, send, but I will do what I can to answer them.

  I recommend first to buy a router, even if it's one you won't connect to internet and it network with others your PC and printer. This will give you the best features and the results of what you're trying to do.

  In addition, the automatic stop of the printer function can be disabled and is not affected by the type of connection. Usually, you can go through the configuration Menu and select tools to change the options there on the energy saving features.

  Finally, the auto off function on your computer is a Windows question, but one easy answer. If you're on a laptop, you can right click on the battery in the tray (lower right corner) and change the settings for energy conservation.

  You might be better off installing the printer via the USB cord and alternately inspiring when you use it, but which is not optimal if you are printing only a few documents on an irregular basis. A network connection is the easiest to manage across multiple computers, honesty, but you have certain requirements for this connection and limits as well.

  I hope this information is useful!
  

• When I try to connect to my wireless network, that it asks a security key how do I find the key my router is a comtrend CT-5363

  When I try to connect to my wireless network, that it asks a security key how do I find the key my router is a comtrend CT-5363

  Hello

  1. what operating system do you use?

  2 did you change on your computer?

  3. who is your internet service provider?

  If you use windows7, I suggest you to follow the steps from the links and check out.

  Set up a wireless router

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a security key for a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-security-key-for-a-wireless-network

• How to reconnect using wired through my router?

  Network wireless adapter NIC Ethernet network device

  How to reconnect using wired through my router?

  Hello

  ·        Are you facing any problem to reconnect to the router?

  ·        What operating system is installed on your computer?

  ·        What exactly is the problem you are having?

  Method 1: Follow the step of the link troubleshooting problem with network connection:

  Wired and in the Windows wireless network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:  If you use Windows 7, then follow the steps for the link to how to configure a router:

  Configure a router

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Method 3: To troubleshoot the problem network connection follow the link:

  http://support.Microsoft.com/kb/313242

• How to set up the internet conection with Windows XP?

  Hello, I just got a windows XP computer, and I'm trying to configure internet for this. I have an ethernet cable that connects to it, but when I plug it in, nothing happens. I open internet Explorer, but I put a dial widget pass. I tried to configure the interent in Control Panel Network, but it did not work. I have a modem that connects to a D-Link router and from there, to your computer and the computer XP. Please help me to set up.

  Hi Brainiac107,

  You get the error message?

  Method 1:  You can see the steps outlined in the article below

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  http://support.Microsoft.com/kb/314095

  Method 2:  You can follow the steps mentioned in the link below to make an Internet connection

  To establish an Internet connection

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/howto_i_client.mspx?mfr=true

  Also check out the article below

  How to set up a connection to the Internet in Windows XP Professional

  http://support.Microsoft.com/kb/305549

• How to set up a network password?

  I have a linksys router and I want to know how to set up a network password. The purpose of this is that I don't want other users to have access to my wireless internet. Either way, I'm using windows xp pro. Thank you so much in advance!

  what you are looking for is a "wireless encryption key.

  I recommend using dartybox.com as a resource for this. Depending on your router, you will find the installation wizards to help you with the configureing wireless security.

  Here are some main parameters that you will want to choose (if you are prompted to set in the Wizard):

  • WPA (not WEP) - maybe isn't able to use WPA2 with XP
  • 128-bit (not 64)
  • password or key: do not use a Word from the dictionary.

  and don't forget there are two 'passwords' on your router. One is the router admin password that gives you access to the configuration of the router. The second is the wireless key or password.

• I need help to set up the linksys adsl router

  Hello world!

  I have LINKSYS WIRELESS - N HOME ADSL2 + MODEM ROUTER (wag120n) and I connect to the internet via the cable that I took my friend who already SPEEDTOCH ADSL ROUTER, I bought the d-link wireless card and I install it in one of my PC
  what I need is to set up my linksys wireless router for my two PCs, on via the wireless and another an ethernet cable, how can I do?

  thanks4all

  Follow this link to configure the router.

• How to set the allocation of network by default in Vista?

  allocation network Deault in Vista

  How to set the allocation of network by default in Vista? I have two routers in wireless network, and it has stopped working. I want to get all default computers to the router to start.  Thank you

  Hello

  Are you connected to the server or if you are on a domain network?

  I suggest you follow the instructions in the link to the configuration of a default gateway on a network:

  Configuring multiple gateways on a network

  http://Windows.Microsoft.com/en-us/Windows-Vista/configuring-multiple-gateways-on-a-network

• How to install an extension for my router

  original title; HOW to SET UP NET GEAR for MY ROUTER to ALLOW MY EXTENSION greater DISTANCE for RECEPTION OF SIGNAL from main router

  I have a netgear router and I want to install an Extender (netgear), so I get enough power from further away in my house.  My main router doesn't have a button of annual work plans.

  Hello

  1. What is the model of the extender?

  Please see the link.

  http://www.NETGEAR.com/images/WN3000RP_DS_22Mar1118-17219.PDF

  I suggest also please contact Netgear support team for assistance.

  http://forum1.NETGEAR.com/

• How to set up WRT120N

  Hello. I have the following problem. I use a static IP address and I use router wrt120n, but to connect to the internet, I plugged the internet cable in the 1,2,3,4 (any) slot. So now I use the part wireless router without "shaping" if I can afford. When I put the internet cable into the slot in the Internet from the router, the laptop can simply connect to the internet - it shows an unidentified without access to the Internet network. I don't know what kind of changes I need to make in the WEB interface of the router. I think I set the type of the connection - now is DHCP and may be putting my IP address, DNS, SubnetMask in the router configuration, but do not know exactly how. I tried to configure the router with the CD interface but it's same - network not identified when the cable is plugged into the port (yellow) Internet. How to configure the router to a router, and not only a wireless switch?

  Looks like the question is weird. If you connect directly to the modem, you can access the internet?

  On the Device Manager, click view on the top. Select to see the hidden device. That should show you something, here.