How to skip a step programmatically?

Similar Questions

• skip the steps programmatically

  Hello
  I want a pop up dialog box in my sequence and have the user select what they want to run, a labview graphical interface.  Is there an available teststand property to set to set programmatically a step to 'jump' once the race started?  I could do this differently by a prior or such a condition, but that gets a little hairy and I want to do as clean as possible.

  Thank you

  David J.

  You can use interactive executions instead of normal operations. See using the API for InteractiveArgs for more details. Another possibility is dynamically defining the runmode on the steps by using Step.SetRunModeEx () (you can pass an execution in this case to make the runmode change apply only to execution, rather than being a step editing tool).

  Hope this helps,

  -Doug

• Skip the step in the package?

  Hi guys!
  
  I have another question theoreticla... Suppose we have a set with a number of steps... and we want to skip the step and do together to run more of the steps... How to do?
  
  I tried with a simple package that was waiting for 10 rows in a table and then was supposed to run scenario... In operator, I've changed the status of the "wainting" step in, but the package did not run yet...
  
  Help, please...
  
  With respect,
  
  PsmakR

  Reestart in the main package, it will be launched from the first stage of "wainting '...

  Cezar Santos
  http://odiexperts.com

• I want to downgrade from 4.0 to 3.6 on my mac. How do I do step by step?

  I have this add on that I like that does not work with the latest Mozilla and I want to downgrade from 4.0 to 3.6. How to do this step by step on my macbook?

  1. Trash Firefox 4
  2. Download and install Firefox 3.6 at http://www.mozilla.com/en-US/firefox/all-older.html

  If you need assistance with installing Firefox on Mac, see https://support.mozilla.com/kb/Installing+Firefox+on+Mac

• How to undo a step and go again StepIndex

  Hello

  I'm evaluating NI TestStand to determine if it meets the needs of a custom application.  The application must include a basic repeating sequence of activation outputs and verification of the response of the system (inputs).  This part seems to be a good target for NI TestStand.  However, so are the execution of these basic IO operations, the system must be capable of monitoring asynchronous.  These asynchronous monitors should occur in several fundamental stages of IO and must also be handled immediately in case of failure.  For example, to control the power supply for 10 steps and immediately stop the test if the supply voltage is insufficient.

  I'll use the supply voltage in the example for the rest of this discussion, but the final solution will have to implement several "monitors".  The condition of 'failure' of the supply voltage is when it falls below a certain limit, and the results of the tests are no longer valid.

  I was able to manage the execution of the MainSequence endpoint using a sous-suite that reads power and calls the Execution.TerminateAll () method when the supply voltage is lower than the limits (monitor).

  I'm now trying to cancel the current step and move on to a new StepIndex (in the MainSequence) after a failure of power supply (detected by a subsequence in a run in parallel).  The new StepIndex can contain the code defined by the user that will manage the error or reach a place that needs more power supply IT.  I hit a roadblock with the implementation.

  I can't find any information on how to cancel a step and proceed to the next step or step defined by the user.

  The only thread I found was here, but does not provide information on how to do what the Application engineer chosen to have a private conversation

  Someone at - it advice?

  There are probably a few different ways that you can implement the behaviour sought. I think with the information that you have provided, continuing to use Execution.Terminate () and take it one step further to implement a monitor in your termination process may be the most appropriate option.

  The monitor of termination is generally used in a code module that performs multiple iterations in a loop. It checks to see if the user has launched a cancellation outside the code module. If your code module is correctly designed, when he learned of the termination monitor that a dismissal has been hired, the loop will be terminated and the remaining unnecessary code will be ignored (I say useless because there might be some cleanup code in your code module that you want to run before leaving the code module). In your case, if you're not perform loops, you can check for a cancellation at several points in your code module. (Note that by default the TestStand waiting step type implements a monitor of termination and will honor a termination of employment)

  Once the code module ends, you can check whether or not a termination was launched at a step after the engine callback and set the desired behavior occurs is it a. (for example, you can cancel the termination and specify what you want to go, be it a call sequence or perform some test steps).

  If you decide to follow this approach, you must ensure that a monitor of termination is implemented in your code modules to appropriate, strategic places. You will also need to be aware that by substituting the engine post-etape callback, there is some added overhead and you will encounter a slightly stricken performance as it will sound at each stage that runs.

  This sounds like a viable solution? I hope this helps.

• How to insert a step to give the position?

  Hello

  I have the sequence with the Select Case structure and to insert steps within the business end. How to do this? I found the index step can be readable by the TS_SequenceGetStepIndex (SequenceHandle, & errorInfo, szTestType, TS_StepGroup_Main, & val), but how to insert new step after, for example the case? For the function TS_SequenceInsertStep (SequenceHandle, & errorInfo, view, iNumofSteps, TS_StepGroup_Main) is not available index (iNumofSteps sucks and does not work as an index of the step and cannot be applied to the order of insertion of the steps (first step on start or end)).

  Currently, I create all (Select, case, end and the steps that need to be in the end case), but if the basic structure can be a default (including case select this option, etc.), only content must be updated, not all construction.

  (LabWindows/CVI coding)

  Best regards

  branar

  Hi all

  Yes, it was the right solution. Only thing, it's that need to take iNumofSteps for the front step and if you want to insert the new stage (or stages), this index should be increased by 1.

  error = TS_SequenceGetStepIndex (SequenceHandle, &errorInfo, "TuningTimeAfterLNA", TS_StepGroup_Main, &val);
                  iNumofSteps=val+1;
                      //add
                      tsErrChkMsgPopup( TS_EngineNewStep (EngineHandle, &errorInfo, "", "Label", &actionStep));
                      tsErrChkMsgPopup( TS_StepSetName ( actionStep, NULL, szTestType));
                      tsErrChkMsgPopup( TS_SequenceInsertStep ( SequenceHandle, &errorInfo, actionStep, iNumofSteps, TS_StepGroup_Main ));
  

  Best regards

  branar

• How can I monitor util programmatically

  Hello.

  How can I monitor util programmatically? in the Windows taskbar, in the Performance section Manager, I can read the util and the use of the CPU, but I want to read directly in Labview, it is posible? is it exists any vi that does this?

  Thank you

  There is an example .net @ C:\Program NIUninstaller Instruments\LabVIEW 8.5\examples\comm\dotnet\SimpleTaskMonitor.llb\SimpleTaskMonitor.vi.

  You can find it by searching examples of labview .net 'Find the examples' [: help find examples]

• How to skip the Startup Repair...

  How to skip the Startup Repair... I started from the install disc and want to "restore full backup for PC. I selected the partition with the corrupt windows installation. The process is suspended, check disk for errors. This check can be ignored. I know it is corrupted and you want to restore completely. No need for this control.

  Hello

  What happens if you leave the disk check to run its course without interfering with it?

  And it is not a good idea to have a backup on the same hard drive, due to the possible failure of the Hard Drive altogether.

  I'm sorry, but nobody here knows why, your system is damaged. There may be problems with bad sectors on the hard disk.

  I suggest download you Diagnostic tools for your hard drive manufacturer, make a Bootable disc and run a diagnostic test to see what the problems are, if any, there is with this hard drive.

  http://pcsupport.about.com/od/toolsofthetrade/TP/tophddiag.htm

  See you soon.

• How to remove a step with the polygon Lasso tool

  How to remove a step with the polygon Lasso tool

  In PS, all you have to do is to hit the DELETE key and you can go back a little with the polygon Lasso tool. How to accomplish this in Fireworks?

  Another option that gives you a lot of control is to use the tool pen instead of the polygon lasso. Because it's a vector path, you can refine the outline very easily using the tools of feather and Subselects and when you are satisfied with the result, click on modify > convert a path to the top. You can even choose to keep or delete the vector path in the preferences panel.

  HTH

• How to change the Description of the c# step programmatically

  Based on user selections in my DLL I want to change the Description of step TestStand.  I use c# 2008 and TestStand 4.1.  I am able to read the Description by using Step.GetDescriptionEx, but I can't find a matching 'Set' command.

  It is a step in editing.  With the help of PropertyObjectFile.IncChangeCount () works fine.

• Change the limit step programmatically in TestStand 3.1

  Hello guys and girls.

  I got a small task for TestStand 3.1 and I don't know how to do this.

  I want to programmatically change the limit of step (multiple numerical limit test) for a step before it is executed. How can I do this? I read that someone suggested to use a step ActiveX to access limits:

  http://forums.NI.com/T5/NI-TestStand/equivalent-to-step-limits-low-NumericFormat-in-TestStand-3-1/TD...

  «TestStand 3.1 can't API calls in expressions (I think that this feature has been added in 4.0 TestStand).» You must instead use a step ActiveX. You can use an ActiveX not configured to call into PropertyObject.NumericLimit and call him on Limits.Low of the step you want to set the property. »

  I am, however, not sure how exactly to proceed since I've never used the ActiveX components in TS before.

  If anyone has the code examples (or write), I would be very grateful.

  -Kim

  As mentioned in this thread, you can certainly change the limits in your version. Read it back.

  p.s. in the future, please post to the Board TestStand and LabVIEW.

• How to stop authentication step 2?

  Right then I made mini niveauZones iPad update. Accidentally say yes to authentication step 2 and now my iPhone always wonder, and it's a pain in the ass cause I have never my iPad with me mini to get this code I need. How can I stop this feature? Help!

  See the last part of this support document to disable two factor authentication.

  For Apple ID - Apple Support two-factor authentication

• How to return a step towards the column in mac when you save the file

  Often when I save files to the web, I want to go back just one step of a subfolder for the column instead of going all the way back to the folder root in the sidebar. How can I return just one step?

  Order arrow up.

  In a file dialog box, you can also click on the drop-down control that lists the current directory. This will show you the hierarchical path. In the Finder, control-click on the title of the window.

  https://support.Apple.com/en-GB/HT201236

• How to disable checks step 2 Apple

  Hello

  I just enabled Apple 2 verification step and I need to know how to turn it off. Can someone tell me how?

  Thank you

  gammyfromms

  Hey! Below are the instructions:

  How can I disable two-step verification?

  1. Sign in to your Apple ID account page.
  2. In the Security section, click on change.
  3. Click on disable two-step verification.
  4. Create new security questions and check your date of birth.

  You will receive an e-mail confirming that the two-step verification of your identifier Apple is turned off.

  Frequently asked questions about the audit in two steps for Apple ID - Apple Support

• How to skip to the previous song, without using the iPod Nano touchscreen (7th generation)

  I want to understand, how can I go back and forth between songs in iPod nano 7th generation.  I thought that all iPods have this easy navigation through buttons system, but I don't think it's available in iPod Nano. After I search the Internet, I found that I can go directly through a double pressure on the middle part of the volume button band. But, is it possible to skip to the previous song?

  On the 7th gen iPod nano, there are three buttons on the side.  Increase volume / Play/Pause : turn down the Volume.  Next song press Play/Pausetwice.  Previous song is triple - Play/Pause-press.

  NOTE: If you have headphones with control buttons on the cord, same three buttons are there, and they work the same way for the read command.