How to test if the pc is connected to the TCP/IP protocol?

Similar Questions

• My computer does not connect to the Internet. Event ID 7003, "the TCP/IP protocol driver service depends on the non-existent service below: IPSec."

  Hello!
  I am working on a Dell Inspiron 1300 laptop for a friend. She has Windows HP Home Edition, SP3 installed.
  He said that Saturday night he started to act funny and wouldn't connect to the Internet. There were a few popups then begins, and he did not know if they were connected to not go on the Internet.
  He had the rootkit.zeroaccess infection. I used Combofix to remove it. It won't always get on the Internet, either via a wi - fi or ethernet connection.
  Looking at the event viewer, I see event ID 7003, "the TCP/IP protocol driver service depends on the non-existent service below: IPSec."
  Then, event 7001, "(NLA) network location awareness service depends on the service protocol driver TCP/IP which could not start due to the following error: the dependency service does not exist or has been marked for deletion.".

  I copied ipsec.sys from another XP Home machine which worked and stuck in the Windows\System32\drivers directory and it still does not work.

  Any ideas are greatly appreciated!

  Dave

  Hello

  See this link:

  http://TechNet.Microsoft.com/en-us/library/cc958861.aspx

  http://www.Microsoft.com/technet/support/ee/transform.aspx?ProdName=Windows+operating+system&ProdVer=5.2&EvtID=7003&EvtSrc=Service+Control+Manager&lcid=1033

  Let us know the results.

• VISA: (Hex 0xBFFF001) timeout expired before the operation is complete. I get this error when you run a VI (instrument is set up to be controlled remotely using the TCP/IP Protocol)

  VISA: (Hex 0xBFFF001) timeout expired before the operation is complete. I get this error when you run a VI (instrument is set up to be controlled remotely using the TCP/IP Protocol)

  Please suggest a solution.

  Thank you very much, it worked!

• How can I activate the TCP/IPv4 properties button?

  Hello everyone, I am trying to solve a problem on my Windows 7 netbook. When I run ipconfig he returned only this line "IP Configuration of Windows" with later data. When I go to the wireless adapter and select Protocol Internet Version 4 (TCP/IPv4), the properties button is disabled. I unchecked the IPv6 checkbox. The wireless adapter is connected to the WiFi hotspot, but the status is not 'connected' for IPv4 and IPv6 connectivity connectivity. I already used the netsh command to reset the interfaces by this link ( http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/tcpipv4-properties-button-disabled/347899fa-b60a-40a3-ad2c-78ef5e0dca37 ). I also have the same problem with my Wired NETWORK card. Please can someone configure me this adapter to get a static IPv4 address or via DHCP?

  -Also reset the TCP/IP stack via (http://support.microsoft.com/kb/299357?wa=wsignin1.0#letmefixit )

  -Also tried re-installing the drivers (http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/the-tcp-ip-v4-protocol-for-the-built-in-wireless/a28c5096-d1c4-4cc4-ab56-236a163e3a96 )

  I had the same problem.

  I noticed that the button of properties available on the network security mode. So I started to disable suspicious services then I found the problem: his "Service to safety nut.

  Doing some research, I discovered that it comes with adware 'Movies Toolbar'. Even if you uninstall the "Toolbar Movies", "The safety nut" always running.

  To uninstall it just open services.msc, double click on 'Service of safety nut' and change the Startup Type to disable, and then restart Windows. When Windows are online again, the button of properties will be available and the safety nut will no longer appear on the services.

  It will be useful.

• How to access a server based on the TCP/IP protocol port?

  Hi all

  Is it possible to access a server through a specific port via TCP/IP?

  We have a step of database server in our network that supports the TCP/IP access. My boss asks if it is possible to get some simple data via blackberry?

  The thing is that blackberry device is not in the network, how can we put a bb device in our intranet? Via enterprise server?

  Alternatively, if we can put the server on the internet, can the blackberry device access via TCP/IP?

  Thank you

  Jerry

  If you use wifi BB can access local servers. using direct tcp: nope.

  You can use a bes express (which is free) If you're afraid of costs, still takes time to install/configure etc of course, otherwise you can only use your product if your BB is in the local WiFi network.

• How to test if the thermocouple is attached.

  Hello, I use the cRIO-9023 and the module NI9213 to read the temperature of the thermocouple. I give to the user up to 16 thermometers already programmed in labview to display the temperature. The question I have, is I want to disable the thermomiters if no thermocouple is connected. I called NOR and they said there is no function integrated to test it, so I have to check by comparing the value. for example, if the units are set to fahrenheit, so if a thermocouple is not plugged it reads to the as 2500 degrees, so what I want to do is to check if the type is fahrenheit and if this is the case, then my temperature max value 2000 degrees. Then I can test IF temp? 2000, disable thermomiter.

  How can I editor a programming like this statement:

  If Type = Fahrenheit THEN maxTemp = 2000

  ELSE IF Type = Celsius THEN maxTemp = 1500

  Basically I want a boolian to trigger an action to establish an indicator.

  Also, if I put an indicator of value of the dome, how can I read it by another controll?

  I would like a way to do it without globial/local variables as my cRIO dislikes the.

  Thank you!

  Use an appropriate comparison function. Most important in this case.

  

• How to test if the rest is a decimal number or an integer?

  Hi guys!

  I want to check whether or not my rest of two integers is a decimal number. Also, if it is a decimal number, I wana it allows to do a thing and if its an integer, I want her to do something else. How can I do?

  Help, please!

  Thanks in advance.

  Craster.D wrote:

  The task is to divide two numbers X and Y and a LED lights up if the result/rest is a decimal number. It can be higher or lower than 1, is not serious. If it is not a whole number, the LED should light.

  Great looks that you know exactly what you want to do, which seems to be the problem?  You will find the functions you need in the digital, boolean and comparison scheme.

• How to test for the node XML empty?

  If (selectedImage.detail! = "")
  
  works with
  < picture detail = "" >
  < / image >
  
  but not
  
  < image >
  < detail > < / details >
  < / image >
  
  
  Hope that makes sense for a person, can't think really how to explain it better, I'm sure it's a fairly simple thing
  
  

  Quote:
  Posted by: ntsiii
  I did not understand. You try to search the nodes in detail where the text node is empty?
  Tracy

  Yes - for that I can't ignore explicitly their.

  Seems that all I had to do was if(!selectedImage.detail)

  Thanks for the reply - despite my not knowing how to phrase the question.

• How can we change the TCP/IP ports used by LabView?

  I'm under LabView 8.2 on a computer running windows XP sp2.  This computer is connected to a compact RIO via Ethernet.  The system works very well, but now I am trying to add an IP intercom function (acoustic digital ii3) this intercom uses a program called talkMaster to communicate with the host computer.  I can't communicate with the intercom because this program needs of ports 3000,3002,5000 and 5006.   I used a program called Currports to see what ports are used, and a program called lkcitdl.exe (National Instruments Logos product name) uses port 5000.  Is there a way to change this? I contacted digital sound technical support and they said there is no way to change it at their end.

  Any help would be greatly appreciated!

  Thank you

  Jason

  I believe that we have an article on this somewhere, but I don't have a link at the moment. Under Windows, you can set the port range used by the protocols of Logos in the registry. Reach

  HKLM\Software\National Instruments\Logos\Ports

  You will find two values DWORD here, FirstClientPort, and FirstServerPort, which defaults to 5000 and 6000 respectively. Logos will search for the first available port in the range [FirstClientPort, FirstClientPort + 1000] or [FirstServerPort, FirstServerPort + 1000] when starts a server or a client. By adjusting the registry, you should be able to find a port range that does not conflict with your software. You need to restart all programs OR after you make this change (probably easier to simply restart the computer).

  -J.D. Robertson

  National Instruments

• How to send files TDMS using the TCP/IP protocol

  Hello

  I work with the cRIO-9025, cRIO-9118 chassis and module NI 9239.

  I did an acquisition (voltage) where data are in 1 d Wfm SGL. I saved these data using a PDM file, but now I want to send this file to another computer (in this case mine) because the file is stored in the target. I have implemented this example:

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/2842#0requirements

  The problem is that the tdms file is created but it has all the data. I have attached the image of the program. The program is in the other (not that I use to make Acq) to make it easy and then works when it works.

  

  * The file name of the client is not used because I had a conflict with the path.

  What I'm looking for, is to make an acquisition of 10 minutes every 30 minutes and then send this data to another computer (or other). I don't know if it's the best way, is perhaps better to send data at the same time as the acquisition is made, but my teacher told me that are easier if I send the file when acquiring ended. Acq, I use FPGA and RT.

   

  I would appreciate your help. Thank you!!

  
  

• How can I disable the Windows XP Pro wifi connection?

  is there a port can I close? I am a novice so it. and I had annother LAN connection.in the last hour. by itself. My firewall has already a lam configuration for microsoft then why my comp need another for microsoft tv on the TCP/IP Protocol on a second lan conn. I did not what has done it? How can I turn off the wireless? on Windows XP Pro. This tenth time im asking this question! Tell me there is at least someone other than my abuser! who knows the answer I needTHANKS * address email is removed from the privacy *

  Hello

  There are a number of ways...

  1. assuming that it is a laptop, there will be a physical to turn off wireless switch, or a depression function key. I can't say what function key, it will be, it varies from laptop to laptop, but the image on the key must be a gift, if the image is not obvious to you then check your manual. Use it with the "Fn" key as a "toggle switch" to turn on wireless power.

  2. go in network connections configuration panel. Right click on your wireless network connection, and then click on disable.

  Your PC is not necessarily to be attacked. It could just be set to automatically connect to networks unsecured wireless. There are a lot of unsecured wireless networks on, leastways in my neighborhood there. If your PC takes up and connects to one, it is not an attack in itself, but it could make your PC open to attack.

  Please mark this as useful or response if applicable.

  Tricky

• How to test the backlight of the Simulator

  Hello Guyz

  Im kind again in the development of blackberry so its more than a new hobby as I recently an interest in java.  So my first app is an attempt to make an application which the camera back given the fon. so I would like to know how to test, without the need to put it on my son, how do I know if d backlight is turned on or off, is the way to display the interface back to the Simulator or something. I'm using eclipse and the blackberry 9800 torch Simulator. How to test the light from my pc?

  Thanks for your time, im hoping a response. Take advantage of the UL

  You can't test the flash of the camera in the BlackBerry smartphone Simulator.  You will need to test this on a real Smartphone BlackBerry.

• How to check if the lid switch is broken on Lenovo Thinkpad X230i?

  I have problems with my new Lenovo Thinkpad X230i lid switch and I would ask you how to test if the lid switch is physically broken. Since I bought the laptop a few weeks ago the laptop suspended when I closed the laptop, but still I had to press gently with my finger on the lid so that the laptop has recognized that the cover is actually closed. Now, this trick no longer works.

  Now, I would like to find a way to better test if the lid switch is physically not works. I found this article in the forum: http://forums.lenovo.com/t5/X-Series-ThinkPad-Laptops/X220-does-not-detect-lid-open-close/td-p/49626... and I followed the steps. I entered the BIOS and closed the cover, but on my laptop, the screen goes out, even if the cover is completely closed and even after pressing gently with your finger.

  I cannot conclude now that the switch of cover material is actually broken and I need the service of Lenovo?

  switch cover on the X 220 and X 230 is triggered by a magnet. The laptop enter the BIOS menu, then use a magnet and see if that turns off the display. IF this is your lid switch is working properly and the problem you are experiencing is most likely software. If it isn't then it is broken, and you need to replace.

• How to test my application of ADF mobile browser on Android emulator?

  Hello
  
  I created a Mobile browser app. Could someone tell me please how to test on the Android emulator?
  
  I read the information on downloading and configuring (Blackberry) simulators and emulators (Microsoft Windows) to browser Mobile ADF in 'Running Mobile Device simulators with JDeveloper and ADF Mobile'. However they mention no details on downloading and configuring "* Android emulators." Could someone help me please in the present.
  
  Concerning
  Raja

  If you want to test the browser applications Mobile ADF (those built with components of the Trinity) - then you run your application in the JDev, copy the URL and open in the browser, which is part of the Android emulator.

  If you want to test ADF Mobile apps - you deploy to the emulator, and then start the application like this:
  http://docs.Oracle.com/CD/E18941_01/tutorials/MobileTutorial/jdtut_11r2_54_2.html

• The ip address of my router cannot be obtained by my cell phone, but he can get other computers. How can I solve the problem?

  Here is the ipconfig/all command information.

  C:\Windows\System32>ipconfig/all

  Windows IP configuration

  Name of the host...: owner-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  WirelessLAN adapter Wireless Network Connection:

  The connection-specific DNS suffix. :
  ... Description: Intel(r) WiFi Link 5100 AGN
  Physical address.... : 00-1E-65-05-FA-DC
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::e582:a22f:fef5:c1af % 11 (Preferred)
  Autoconfiguration IPv4 address. . : 169.254.193.175 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  DNS servers: fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
  NetBIOS over TCP/IP...: enabled

  Local of EthernetAdapter network connection:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: Realtek RTL8102/8103 PCI-E FE Family NETWORK map
  Physical address.... : 00-23-5A-0D-E6-2A
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {D57EF487-9E9D-4432-A3F6-09941DBAC
  B 9, 7}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 12:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 13:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {82CD5F3A-4FE2 - 41 D 2 - 9313-09635 C 287
  3A 1}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  

  0

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET