How to use LabView for Primera Bravo II CD burner control?

Similar Questions

• How to use labview for controlling the HP Network Analyzer

  Hello

  I have a HP network analyzer 8720D connect with my laptop by a USB-Gbspecifications FOR cable. I want to use LABVIEW for control to parser do measurement and data collection. What should I start? Where can I get the labview program to control the parser?

  Thank you.

  Help > find instrument Drivers. Then go to the Instrument Driver Network and read all the links on the use of pilots.

• How to use Labview for measuring the reflectance at different wavelengths automatically

  Hello!

  I'm using labview to communicate with MS257 (a monochromator). If I do not use Labview, I have to use the hand controller (set a wavelength from 300 to 1100 under a grating (a total of four grids).) It takes a lot of time. So I want to use labview to realize the automation. But I don't know how to do, I still can put only a wavelength as a command for MS257, not making any difference.

  Does anyone know how to deal with this?

  Thank you for your time.

  So where are you stuck? It is a fairly common task. Inside of a loop, you can increment the "xxx" and build a table of responses. Look at the Format function in the chain and a knot of shift register/feedback.

• How to use LabView for Pyros fire (devices)

  I searched NI Forums and google on this subject, but can't find much.

  Can someone help me understand what modules I need to shoot a few different pyros (aka, Squibs devices) such as cable cutters, bottle openers, etc.?  We use a 9172 chassis.  I can monitor and record data from a pressure sensor with voltage module and production of 9205 with a module 9263 without any problem.  I can not just current output enough with the material that I have now.  Pyros should I use require anywhere from 1 to 5 Amps and so far up to 6.15 volts to activate.

  I have not seen any module that can much more output current.  However, 9481 relay module could be promising if it can give me another amp or two at a lower voltage.  The range says 4 amps at 30 VDC.  My future plan must have the VI the first pyro when the pressure reaches a specified point and then fire the second pyro at a specified after the first time.

  Someone out there has have done something like this before.

  I'll worry about programming after I find the material.

  Thanks to all those who can help you

  I would not recommend to use the outputs digital Parallels. They can't really spend exactly synchronously. So by setting on and outside we can overload and destroy the circuits of switching first and last respectively.

  I recommend you add a simple electromechanical or solid state relays.

• How to use pthread_create for multithreading in C/C++?

  Goal: Create two threads at the same time to collect and process the data.

  Error: Buffer problem. A [i] when I is increased, the accident will be held later.

  Question: How to use pthread_create for multithreading in C/C++?

  or you know any related document, I can read?

  Mini code:

  pthread_t A, B;

  void * rawacceleration(void*);
  void * featureacceleration(void*);

  pthread_create (& A, NULL, & rawacceleration, NULL);
  pthread_create (& B, NULL, & featureacceleration, NULL);

  Thank you for your attention.

  Sorry guys.

  It is a buffer problem.

  Try i = 0 to [i]. The problem is resolved.

• How to use a FOR LOOP to create multiple forms?

  I use Adobe animate CC (formerly Flash Professional CC) and I am trying to adjust the following snippet so that it creates several rectangles:

  var form = createjs new. Form (new createjs. Graphics ().beginFill("#FF0000").drawRect (5,5,100,100));

  this.addChild (shape);

  I then set it and put it in a loop I thought work in the reproduction of the form. The following code creates only a rectangle well?

  for (i = 0; i < 10; i ++) {}

  var i is new createjs. Form (new createjs. Graphics ().beginFill("#FF0000").drawRect (5,5,30,30));

  this.addChild (i);

  Move so that they do not lie on the other

  This.x += 50;

  }

  I think that the problem is how you use your iterator variable. In your loop, at the first start, i is equal to 0, then you immediately replace 0 with an instance of the Shape class, which means when he tries to loop again, I is not less than 10. They can't, because it is now a shape, not a whole number.

  Try this inside the loop:

  newshape var = new createjs. Form (new createjs. Graphics ().beginFill("#FF0000").drawRect (5,5,30,30));

  newshape.x += 50;

  this.addChild (newshape);

• How to use profiles for the metadata tab in window of Contribution

  Hi Experts,
  
  Is it possible to use profiles in metadata tab Contribution. ??
  
  I want each payable region must have its own profile. For, for example, if the user will pay company information, then the metadata tab should show only metadata related company, not other meta data that are not relevant here.
  
  
  
  Help, please

  I thought you said you knew how to use/create profiles in your previous post...

  It's the quick rundown: like the regular profiles, you will first need to make sure your content has the metadata field to trigger profile assigned when it is created. This is done in designer under the definition of "Changing the content of the region" in your area of contribution. Assign the "value of trigger to profile" under "Default metadata" and then as idoc to the activation of your profile content rule condition.

• How to use % symbol for parameters in conditions in Discoverer

  Hi all
  
  In fact, I have to add four settings in that
  two param should be % (average for select all) as a default.
  
  That is to say that we use LIKE '%' in the query.
  
  the problem is when I enter a value for a parameter, it should train for this value,
  and if I need anything, I should enter the "%" symbol,
  
  so, for what Iam confused how to use this,
  
  Although I tried with a few options, it receives satisfactory results.
  
  someone will help me please to achieve this.
  
  Thank you in advance
  
  Published by: user10271105 on Sep 17, 2008 03:37

  Hello

  You can create a parameter and give % as default. If you set the condition to use AS and when the default is used for the parameter, then the query contains LIKE '%' and everything is selected.

  If you are using a list of values with your parameter, then you must add the '%' to your list of values so that the user can select this value.

  However, this method will not work if some values in your database contains characters of percentage, because the condition LIKE 'ABC DEF %' will return as well as ABC % DEF ABCXYZDEF.

  Unfortunately like escape syntax is not available in discoverer, so you have to invent a value that the user can enter for all, for example ALL the default value for the parameter.

  Then use a similar State to:

  question LIKE: param OR item = DECODE (: param,'* ALL *', item)

  Rod West

• How to use iCloud for PC without an iOS device?

  I received an invitation to join a place to share photos of iCloud.  I'm not an Apple user, do not have an iOS device (or plan in the near future).

  I've created an Apple ID iCloud and have iCloud account.  I downloaded and installed iCloud for Windows on my PC.  However when I try to run the program and enter my Apple ID and password to connect, I get the following message:

  Unable to connect

  Your identifier Apple must serve to iCloud on an OS X device or an iOS to install before you can use iCloud for Windows.

  Is this to say that I can't access the iCloud photo sharing subscription since I did not have an iOS device to set up my account?  ICloud photos can be shared with users who have an iOS device to that?

  Thanks in advance.

  You can create an Apple on a Windows PC ID, but you cannot create an iCloud account - it is a separate additional process and unless you've been able to create one on a Mac or iOS device you don't have an iCloud account, only an Apple ID. This is why the error message you see.

  iCloud accounts are essentially positioned as a way for Mac/iOS users synchronize data from their devices and are a free service at the Starter level; the control panel is intended for users of Mac/iOS, which also happens to have a Windows PC. They are not intended for Windows users only. Unless you can find a way to set up a device to iCloud on a Mac or an iOS device, you will not be able to move forward.

  iCloud sharing photos can be configured as a public or private - the first are directly accessible in any web browser, but private sharing requires you to have iCloud account. If your source is not willing to set up a public share (that would be accessible to the world in general) you will not be able to access it without an iCloud account.

• Can I use Labview for my Samsung S3C2410?

  Hey guys,.

  I have a dev based on Samsung S3C2410 CPU board

  I bought at developmentboard.net. See the specs HERE .

  My question is:

  I want to use LabView on this forum, can I?

  Any information will be appreciated, thanks in advance ~

  Hi Leon,

  Hope you are doing very well. You can use the NI LabVIEW Microprocessor SDK (Software Development Kit) with a string of third-party tools and an embedded operating system to target any 32-bit platform of your choice. Samsung S3C2410 uses ARM based 32-bit RISC microcontroller, so you should be able to use LabVIEW. Please click here to learn more. I hope this helps.

  Best regards

• How to use findByPrimaryKey for concatenated PK

  Hello
  
  How to use EntityDefImpl.findByPrimaryKey (transaction, key) when the primary key is composed of two or more attributes?
  
  Thank you
  
  Anatoliy

  Anatoly,

  Object[] supplierKey = {value1,value2};//Put as many as u need
   EntityDefImpl supplierDefinition = SupplierEOImpl.getDefinitionObject();
  SupplierEOImpl supplier =  (SupplierEOImpl)supplierDefinition.findByPrimaryKey(transaction, new Key(supplierKey));
  

  Kind regards
  GYAN

• How to use partitioning for large table

  Hello
  
  ******************
  Oracle 10 g 2/Redhat4
  RAC database
  ASM
  *******************
  
  I have a TRACE table that will also grow very fast, in fact, I 15,000,000 lines.
  
  TRACES (IDENTIFICATION NUMBER,
  NUMBER OF COUNTRY_NUM
  Timestampe NUMBER,
  MESSAGE VARCHAR2 (300),
  type_of_action varchar (20),
  CREATED_TIME DATE,
  DATE OF UPDATE_DATE)
  
  Querys who asked for this table are and make a lot of discs!
  
  --------------------------------------------------------
  Select count (*) as y0_
  TRACES this_
  where this_. COUNTRY_NUM =: 1
  and this_. TIMESTAMP between: 2 and: 3
  and lower (this_. This MESSAGE) as: 4;
  ---------------------------------------------------------
  SELECT *.
  FROM (SELECT this_.id,
  this_. TIMESTAMP
  Traces this_
  WHERE this_. COUNTRY_NUM =: 1
  AND this_. TIMESTAMP BETWEEN: 2 AND: 3
  AND this_.type_of_action =: 4
  AND LOWER (this_. MESSAGE) AS: 5
  ORDER BY this_. TIMESTAMP DESC)
  WHERE ROWNUM < =: 6;
  -----------------------------------------------------------
  
  I have 16 distinct COUNTRY_NUM in the table and the TIMESTAMPE is a number that the application is inserted into the table.
  
  My question is the best solution to resolve this table is to use partitioninig for a smal parts?
  I have need of a partitioning using a list by date (YEAR/month) and COUNTRY_NUM, is there a better way for her?
  
  NB: for an example of TRACES in my test database
  
  1 Select COUNTR_NUM, count (*) traces
  Group 2 by COUNTR_NUM
  3 * order by COUNTR_NUM
  SQL > /.
  
  COUNTR_NUM COUNT (*)
  
  194716 1
  3 1796581
  4 1429393
  5 1536092
  6 151820
  7 148431
  8 76452
  9 91456
  10 91044
  11 186370
  13 76
  15 29317
  16 33470

  Hello

  Yes and part is that you can remove the whole score once you don't need "of them. I think you should be good to go. Let me know if you have any other questions.

  Concerning

• How to use kinect for gesture recognition in labview? is that a library can be used?

  I want to use kinect recognize the gesture to control some device (like lamp). use of labview to program, is there any library that I can use to make it easy to achieve?

  Yes, there is.

  Kinesthesia Toolkit for Microsoft Kinect - University of Leeds

  Christian

• How to use Labview to control the motorized turntable?

  Hello

  I am new to Labview and do a project that requires the use of labview to control the motorized turntable (XYZ axes). I need to use the Labview programming and have no idea at all. Need help, thank you very much!

  Lei,

  Everything said by others is correct and to do because they describe, at a given time. But I always approached these projects of motion control first by looking at the 'motion controller' (I hope you have a) and 'drivers' (what you need) between the computer/LabVIEW and engines decide what communications will be required for these devices and get an idea of the syntax of command and the language to use with them.  In some cases, the controller and the motor driver are integrated in a single unit. Heck, in some cases, they are even integrated with each engine.

  The motors can be the stepper motors or perhaps servomotors.

  In the case of drivers stepper (devices that provide power electronics to run the engines), many of them are run using only two control signals for digital called 'step' (a pulse train) and 'direction' (high-low level) and if it is possible to generate directly with the PC, it's an order of magnitude easier (if you have not already a library of available motion control to manage the generation of these signals and) the execution of the stepper motors) of having a "Motion Controller" between the PC and the "motor".  Engine drivers step by step usually can be configured that current engine and the size of the stage and sometimes for the other plus-moteur/driver-parameter setting. The configuration of these can be made with jumpers, switches or, for some drivers, with orders ASCII on some sort of port of communication, but in general these are values you download the installer once at the beginning and then never touch again if you do not need generally to have a full time available on their change communication path.

  In the case of the actuator drivers (once again the devices that provide power electronics to run the engines), many use a +/-10V control input analog signal, and, again, while it is possible to generate the signal directly with the PC hardware, a separate axes controller is usually much simpler and more robust.  In the case of a servo system, there is also a signal back to an encoder or resolver attached to the engine to be used by any device will exercise the motion controller in the system.  There are once again associated with the driver configuration parameters (and controller in this case, since it is part of the servo feedback loop) which must be configured at the start but once set up properly, they rarely need to be changed again.

  A movement controller which is separated from the PC often manage several drivers, and can often coordinate a movement between them. It will load the rise up/down of the engine speed as that changes. It will be followed by position of each motor. The servo system, but it will take the feedback signal and use it to adjust the speed/position/torque of the engine. The motion controller also deal with race and home or index of signals is usually on most lines of movement and provide information of the State of the switch to the PC.   To run the motor controller is then just a matter of chaining a set commands of (usually ASCII) to indicate how fast to run and how far to go (and direction) and by sending a command "do it." Then, ask you to keep track of the status of the process and the States of the switches.

  In many cases the builders of controllers of movement are a primitive way to communicate with the controllers of a PC with no additional software other than what they offer. With this you can at least have an idea of how different the controller commands and responses they produce. That you can start to build sequences of commands to perform the actions you want.

  You can then add LabVIEW to the mix and to understand how you can get it to send sequences of similar orders on the paths of communication that are available and respond intelligently to the information it receives in return for motion control.

• How to use wireless for my TECRA S1

  I have a TECRA S1 and you want to use the wireless function to get on Internet, I already have two pc is connected to my wireless network how can I get my laptop on the network now.

  Thank you

  Hello

  -check if your laptop has a WIRELESS card with onboard (Manager of devices under network adapters or WiFi label on the low side)
  -If yes turn it on using wireless switch antenna ON / OFF in the front near the headphone jack
  -When the control led is CHECK if the WIFI is enabled by using the FN + F8 key combination
  -Depending on your local settings WLAN connectivity must be configured properly (TCP/IP)
  -You can use the Windows settings for WLAN configuration (you can find it under the "networks" tab a wireless WLAN properties)
  -refresh the available networks and if your LAN is displayed there you can add it as a favorite and configure (encryption)

  All that s!