How to use multipule join in update stmt

Similar Questions

• How to use the utility to update (uefi) BIOS HP

  Notebook: G62 a10em

  I downloaded the BIOS update tool from http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063 & lc = on & cc = us & dlc = in & sw_lang = & product = 4226...

  and it is installed on my USB key.

  Now, how can I update my bios?

  The USB key contains now:

  BIOS

  | - Current (empty folder)

  | - New (empty folder)

  | - Previous (empty folder)

  BIOSUpdate

  -CryptRSA.efi

  -CryptRSA32.efi

  -HpBiosUpdate.efi

  -HpBiosUpdate.s09

  -HpBiosUpdate.sig

  -HpBiosUpdate32.efi

  -HpBiosUpdate32.s09

  -HpBiosUpdate32.sig

  my current version of bios is f. 08

  I did a cut above.

  After looking at the appropriate file you downloaded, it says this:

  "Prerequisites .
  -Microsoft .NET 2.0 is required. UEFI and Custom Imaging - the HP BIOS update must be run from a FAT or FAT32, partition with a volume of the "HP_TOOLS" name This Installer gives you the option to install on the hard disk (HDD) or USB. If you install on the HARD disk and the HP_TOOLS partition is not present, Setup prompts to create the HP_TOOLS partition. If you install on a USB key, Setup renames the partition on the USB in HP_TOOLS. If you use a custom image, you can create the HP_TOOLS partition manually with the type FAT32 and that the volume HP_TOOLS name. ATTENTION:-the UEFI system partition is not protected and can be removed. -Backup of the computer by using the complete PC Backup feature of Microsoft Windows Vista does not save the UEFI system partition. For these reasons, HP recommends that you place no additional data on the UEFI system partition. Because the partition is not backed up, corruption or failure of the partition will result in the loss of all data on the partition, as well as the loss of UEFI functionality. "For more information, visit: www.hp.com/go/techcenter/startup"

  There is little documentation on how to use it, but a Member here figured it out.

  http://h30434.www3.HP.com/T5/operating-systems-and-software/envy-14-system-recovery-doesn-t-work-with-latest-BIOS/m-p/328684/highlight/false#M45165

  using Windows 7:

  Just plug in the USB key and then run the SPnnnnn.exe BIOS file downloaded from the Web site drivers HP.

  Assuming that the USB is configured correctly (see below), Setup the BIOS sees the HP_TOOLS partition on the USB, copy of the BIOS and its file signature on the USB key, then run Setup winflash. The system BIOS detects the USB and the partition HP_TOOLS and the BIOS is magically updated.

  I put in place a new USB key as follows:

  1 rename the partition HP_TOOLS from the hard drive to something different like HP_TOOLSbak

  2. Plug the USB

  3. Download and run the utility to update the BIOS (not the BIOS, still) drivers HP support page.

  4. Select the option to install to a USB

  5. Select the option to create the partition HP_TOOLS

  6. The reader should now be formatted as HP_TOOLS with a record of Hewlett-Packard containing BIOS and BIOSUpdate records. The BIOS folder contains empty current, news and previous records.

  7 download and run the HP System Diagnostics (UEFI) MS drivers HP support page

  8. Select the option to install on a USB key. This will create a SystemDiags folder under the Hewlett-Packard folder

  9. Download and run the HP Notebook System BIOS update for the HP support page drivers, given that the USB is correctly tagged it will install the update of the bios on the USB drive

  10, we have to end up with a HP_TOOLS partition on the USB drive identical to the one that you removed from the hard drive.

  Once you have configured the USB drive, you can upgrade to other versions of BIOS (most recent or oldest) using this drive, as I mentioned above: just plug in the USB and then download and run the BIOS Setup program.

  Having said that I'm not sure of what you do, once you boot the USB drive.

  .

• How to use the checkbox to update several lines

  Hi all

  I'm new to apex and I have a problem now. I find this code somewhere:

  BEGIN

  FOR I IN 1... APEX_APPLICATION. G_F01. COUNTING LOOP

  REMOVE FROM THE ASER

  WHERE ID = TO_NUMBER (APEX_APPLICATION. G_F01 (I));

  END LOOP;

  END;

  It can remove selected items, now I want to make some modifications to it.

  I want to update some columns when I ticked the box. How to make this change? I mean, like this:

  UPDATE ASER SET STATUS = '1' when I selected items

  Can you help me? Thank you!

  Hello

  I don't know exactly what you want to do, but if I am guessing right then of course you want updated also based on the elements of the selected check box.

  
  BEGIN
   FOR I IN 1 .. APEX_APPLICATION.G_F01.COUNT LOOP
  
     DELETE FROM ASER
    WHERE ID=TO_NUMBER(APEX_APPLICATION.G_F01(I)) ;
  UPDATE APSER
  SET STATUS = 1
  WHERE ID=TO_NUMBER(APEX_APPLICATION.G_F01(I)) ;
     END LOOP;
  
    END;
  

  But if not and you try rather to use these values to update another table after Session State is the way to go.

  Kind regards

  Benjamin.

• Help! How to use a join internal?

  I like to use Coldfusion, but my coding knowledge is Basic. I do not understand to coding of inner join. By using the code below, I can get (bar code) Column1 and Column2 (quantity). How can I use inner join to get columns with product_name, and the price of another table (inventory - based on the same number of barcodes in both tables) so that I can insert ALL four fields in a new table (cart1)

  <!-FIND DUPLICATES AND SUM AMOUNT->

  < cfquery name = "CountBarcodesTemp" datasource = "inventory" >

  SELECT the barcode, Sum (Quantity) as the quantitysum

  TEMP

  GROUP BY barcode

  < / cfquery >

  -Thank you.

  Okay, one thing to consider here is that this is a forum for CF, and ask yourself a question of SQL.  Is not really to be best place to be direct SQL questions (which is not to say you won't get a response, but it is not really appropriate for these forums).

  There is not much use of INNER JOIN.  It is simply this:

  SELECT [your columns here]

  FROM table1 INNER JOIN table2

  ON table1.someCol = table2.someOtherCol

  Where someCol and someOtherCol represent a relationship between two tables; in your case, it seems that the barcode ID is the column that links the two tables, the join statement so along the lines of

  THE INNER JOIN inventory temp

  ON temp.barcode = inventory.barcode

  That said, it does for SQL more readable if you alias your tables too, for example:

  SELECT t.somerCol, i.someOtherCol

  I have TEMP t INNER JOIN stock

  ON i.barcode = i.barcode

  Whenever you want to reference the tables later, you use the alias, not the name of the table.

  I think you should probably search the docs online for any DB that you use and give them a reading.  Or buy a SQL Tutorial book and through, or something, too much work.

  --

  Adam

• How to use "full join" in ODI interface

  I need to join two tables using full join. Then, when I do drag table columns (join build) and mark the left and right join (get full join):
  + (All lines of OSS_NCELLREL (OSS_NCELLREL), including the lines not matched with lines of OSS_NECELASS (OSS_NECELASS) and all lines of OSS_NECELASS (OSS_NECELASS) including the lines not matched with OSS_NCELLREL (OSS_NCELLREL) +)
  I get the following error:
  The source of the diagram Panel: Clause set to join full on a technology that does not support full joins
  
  I use Oracle DB tables in the same PB.
  
  Help! What I've done wrong?

  Hello

  You need work in the topology Manager.

  Please follow the steps below

  1. change the 'Oracle' in the tree of the physical Architecture technology.
  2 If ' technology Defintion tab select button radio "Ordered (Sql ISO).
  3. in the "SQL Tab" technology do the following settings:
  -Clause location: of
  -Media supported clauses: check
  -Inside: check, type INNER JOIN
  -Cross: check, type CROSS JOIN
  -Left outside: check, type LEFT OUTER JOIN
  -Right outside: check, type RIGHT OUTER JOIN
  -External more info: check, type FULL OUTER JOIN

  PS: Please take a techno Oracle backup before editing. ;)

  Thank you
  G

  Published by: Gurusank on November 27, 2008 21:05

• Satellite A210 - 16G (PSAELE) - how to use 4 GB and update the BIOS?

  Hello! I hope someone can answer a few questions for me.

  First of all is: How can I turn on my laptop to use all the 4 GB of RAM? OS is Win Vista Ultimate 32-bit with Service Pack 2. Now Vista all show the 4 GB of RAM, but don't use it. I activated the EAP in Vista, but still nothing. As I saw, I need to turn it on too memory remapping in BIOS but there is no option (my BIOS is ver.1.70).

  The second question relates to the BIOS. Because my version is 1.70 and there are more recent version 2.00; I get benefits if I update to BIOS? Someone has updated to version 2.00? And there are more options in the BIOS after update to version 2.00 (for example the memory remapping or a similar option)?
  I'm a little afraid to update BIOS, because sometimes my Toshiba freezes, and I would not hang during the update of the BIOS.

  And the final question is there any changelog to the BIOS? So I can see what is added and changed, and what's new in the new version of the BIOS. Because I could not find anywhere.

  Thanks for the responses to come.

  Hello!

  (1) you can use the entire 4 GB of RAM on a 32 bit OS. It is a due limitation of 32-bit technology. Windows Vista with Service Pack 2 may recognize the full 4 GB of RAM but not use it, more than 3.2 g.
  Here you can find more information about this limitation:
  http://APS2.toshiba-tro.de/KB0/TSB82022E0000R01.htm

  (2) about BIOS updated I can tell only must be made only if you have problems with the laptop. A BIOS update should never be done just for fun, because it of still a little risky. In the worst case, you can destroy the ROM module or complete motherboard.
  Update the BIOS doesn't normally contain new features or options. It s bug just setting. In addition it can t solve the problem with 4 GB of RAM and Vista 32 bit if you think that ;)
  If your laptop does not have 100% stable you shouldn't t update because it s too risky. Before the update, you should try to solve the problem of gel.

  (3) If a change log is available you can find it on the Toshiba site. If you can t find, there isn t available.
  That s all about this.

  I hope I could help a bit.

  Good bye

• How to use bind variable to update the DB 11 GR 2 access data

  Hello Experts,

  By DB version 11 GR 2

  Operating system Windows Server 2012 - 64 bit

  I want to update some data base record Access to oracle with database link. Here is my SQL, which works.

  UPDATE Transaction@DB_LINK
  SET "WorkCode"=1
  WHERE "WorkCode"=0; 
  

  But, I need to change that to

  UPDATE Transaction@DB_LINK
  SET "WorkCode"=1
  WHERE "DateTime"=:VARIABLE_DATE_TIME; 
  

  and a 2nd does not.

  Any code help or example?

  Ask2Learn

  Hello

  Use DBMS_HS_PASSTHROUGH

  try something of

  DECLARE
    c       BINARY_INTEGER;
    nr      NUMBER;
  BEGIN
  
    c := DBMS_HS_PASSTHROUGH.OPEN_CURSOR@DB_LINK;
  
    DBMS_HS_PASSTHROUGH.PARSE@ATTD_ENVOYF(c,'UPDATE Transaction@ATTD_ENVOYF SET "WorkCode"=1
    where "DateTime" = '||''||VARIABLE_DATE_TIME||'');
    nr:=DBMS_HS_PASSTHROUGH.EXECUTE_NON_QUERY@DB_LINK(c);
    DBMS_HS_PASSTHROUGH.CLOSE_CURSOR@DB_LINK(c);
  
  END;
  

  Hope this helps

  Hamid

• I bought the plan for photography and still pay each month. but I can't use photoshop only after update. and they need to join a plan. How can I do? I can only use for the trial version even I never tell months.

  I bought the plan for photography 6 months ago and still pay every month.

  but I can't use photoshop only after update. and they need to join a plan.

  How can I do?

  I can only use for the same test version that I pay every month.

  Hi yejik42305752,

  Please see the following article: https://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  Kind regards

  Tanuj

• How to update when the defined condition is to find using the join

  Hello everyone
  I want to update a column of the table, and the value can be found using another table
  then, how should I update using the join in the set condition
  Suppose there are 2 tables and 5 column are frequent at home
  Now, I want to update a column by using join conditions
  
  Suppose that

  select a.column5
  from table_1 a, table b
  Where a.col1=b.col1
  and a.col2=b.col2
      .
      .
      .
  and a.col8=1000000002

  It's the Party join now I want to use guess a.column5 in the fixed part of the update
  

  update b
  set b.col5= a.col5

  You must use your pk in the query.

  update table b
  set b.col5= (select a.column5
                            from table_1 a
                        Where b. = a.whatever
  

  This problem is with your query logic... read it again.

• How to use the same software on 4 update 1

  I just upgraded my esxi 4.0 to 4.0 Update 1.  What I read this update should come with the same software that will help me join this host to my MS Active Directory.  But I can't find where it is or if it is installed.  Where is it and how to use it?  In case you're wondering, I'm joining the ad without the use of vCenter.  Thanks for your help.

  The Web site suggests that it might be a future version of ESXi not version 4.0 - U1. Supported in ESX at the present time.

• Given that I have updated to IOS 9.2 my Ipad 2 Air is discharge the battery in 12 to 14 hours, even without any use. Before the update, after a day of average use of the battery was still 70-75%. How can I reinstall the IO 9.1?

  Given that I have updated to IOS 9.2 my Ipad 2 Air is discharge the battery in 12 to 14 hours, even without any use. Before the update, after a day of average use of the battery was still 70-75%. How can I reinstall the IO 9.1?

  Hello

  The best way to save battery life is to go into the settings and turn off Apps Refresh

  I now get 3 / 4 hours of battery life more.

  You cannot return to a previous ios 9.1

  See you soon

  Brian

  PS

  If you still have a problem iCloud backup now

  Then restore settings to get rid of any bugs.

• How to use windows update with browser firefox4

  How to use windows update with browser firefox4

  You MUST use Internet Explorer to access http://windowsupdate.microsoft.com.

• I get request to update my Flash Player from Adobe. What is c? Where to find info on how to use it?

  I don't really know how to use this thing, I'm seriously "physically challenged and a slow-learner." and my computer repair man keeps changing computers about me.  (In this I am not sure that it helps me.  Once I have to get used to some programs, there are 'new '.   His "real confusion.  For example, I got a real easy to use-address book that had all my personal and business addresses and telephone #s in there.  The computer got a 'blue screen' several times, so he came and changed my "Dell XPS" computer professional with a 'new' (a ' Dell 7 Ultimate' it was 'better'.    If I could afford it, I buy a new one and start over) so I rarely know 'where' I am, or what to do when I'm 'where I am.  With a full-time job and a serious hobby of computer repair, it doesn't have the time to help me with "operational" issues This put an unfair burden on anyone trying to help me, but I HAD TO GET HELP - SOMEWHERE, so if I'm not a gene with what will be long-term issues (because I don't know much about the computer operations), can I impose to ask what might be the basic questions?  Of course, they cannot be "basic", but what I know.     I read "... for Dummies" books, but they did not answer my questions.  I'll try to be brief, but it's not my nature.          So, let's go...

  Sometimes I get request to "update my Adobe Flash Player."  I have looked under Start programs and everything I find is "Adobe Flash Player";  I do not use reader because I do not know how, or its purpose.  But I feel like I'm missing out on thing, why would he says in the 1st place?  (I don't want to watch videos, and somewhere, I think I remember it may have something to do with it.  If so, I peut have a NEED for him.  And if so, where can I find information on how to use it.  Once again, if so, I also NEED the Flash Player?

  Original title: * e-mail address is removed from the privacy *.

  Flash Player is used by some web sites to improve how their web page or pages are displayed. If you go on a site that uses Adobe Flash and Flash Player is not installed on your computer, you will see a request to install Flash Player. When Flash Player is installed, then you can never know its duration as its transparent you when loading a web page.

  In your case and on my computer I installed Flash Player, and for this purpose, I see the same update request that you see. It is best to install the update to the latest version of bugs or security risks that may currently exist in the old version install on your PC.

  J W Stuart: http://www.pagestart.com

• How do I know which account was used to join vCenter

  Hello

  I was wondering if anyone knows how you can know which account was used to join the hosts to vCenter.  We try to hunt down to an older installation, but can't seem to find it anywhere?

  Any help would be greatly appricated.

  You have to be Root - adding a host to vcenter requires root-level privileges and I know anyway to SUDO and add the host that it should have been done as root.

• How to use adobe 5.0 on windows 7 to install 2 updates.

  How to use adobe 5.0 on windows 7 to install 2 updates.

  Keith you may be faced with an issue trying to install Photoshop CS2 on Windows 7 in general.  If you have two serial numbers enrolled, and one of them is a full version, you can request that your software be unlocked to allow installation.  Our support team will be better able to determine your eligibility for this.  You can contact them via chat at http://adobe.ly/yxj0t6.