HP DM4T - 1100 Win 7 clean installation

Similar Questions

• Satellite Pro P100-327 (PSPA4E) - none follows her Win 7 clean installation

  Hello

  I just clean installed Win 7 Home Premium (64 bit) on a Satellite Pro P100 - 327 (PSPA4E) which was bought in November 2006. He was previously under XP. I never installed Vista, even if the laptop is Vista Capable badge.

  I followed the recommended order of installation of the bios/driver/software Win 7 but I have now no sound at all. Everything I've tried so far has failed to fix.

  The laptop has a Conexant based with harman kardon speakers audio solution. Win 7 installed the following driver, which brings the info.

  High definition Audio Device (Microsoft Driver version 6.1.7601.17514 as of 11/19/2010) and status of the device: this device cannot start. (Code 10)

  Hardware ID:
  HDAUDIO\FUNC_01 & VEN_14F1 & DEV_5047 & SUBSYS_1179FF31 & REV_1000 HDAUDIO\FUNC_01 & VEN_14F1 & DEV_5047 & SUBSYS_1179FF31

  There is a second exclamation mark in device for a more Manager unknown device / uninstalled the device driver with an ID of ACPI\SMCB000 material (display code 28) but I don't know what is this device!

  Anyone have any suggestions on a fix for my sound problem?

  Thank you!

  Martyn

  ACPI\SMCB000 could be the infrared device.
  Perhaps his need in order to use the remote control.

  I also looked for VEN_14F1 and DEV_5047
  It seems to be the HDAUDIO Soft Data Fax Modm SmartCP of Conexant
  http://www.PCIDatabase.com/search.php?device_search_str=5047

  I checked the page of the Toshiba driver for Win 7 drivers for similar laptops Sat P105-xxxx and found the driver here:

  [Drivers of Toshiba U.S. page | http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/modelContent.jsp?ct=DL&os=&category=&moid=1598605& rpn = PSPADU & modelFilter = P105-S6227 & SelCategorie = 2756709 & selFamily = # 1073768663]

• Qosmio F60 Win 7 clean installation and drivers

  Hello
  I would like to clean install win 7 64 bit on my F60. I've worked on how to change my boot sequence, [with the help of this forum], so I'm ready to format & reinstall. However my concerns relate to reinstall specific drivers for the F60... Any advice on this process would be appreciated. Is it a matter of just download from [http://www.mytoshiba.com.au/support/notebooks/qosmio/f60/pqf65a-00y002/download?os=25] & installation that I need. If this can be difficult?
  Any thoughts & guidance appreciated
  Lantana cordially

  Here also to update bios... is there a process step by step for that too?

  Hello

  If your Qosmio F60 is an Australian model, you can download all the drivers and tools of the Australian page. So that s in the right place for this.

  Otherwise, follow the installation order posted by Akuma. Also check the content of the forum, you will find enough discussions about the order of installation. Personnel chipset driver must be installed in the first place.
  Don t forget the LAN/WLAN and Bluetooth driver

  Before you begin to install another OS, make sure that you have created the successfully recovery disk.

• HDD with Win 7 clean installation problem

  Hello everyone,

  I have a new FreeDos Y560 and impossible to install Win7. It shows all partitions in the menu Setup, but for everyone, says that windows cannot be installed. He tells me that they cannot be formatted ntfs (which is false) and also check the controller in the bios. I switched from ahci to ide mode and have the same problem.

  Windows xp starts installation (only in ide mode), but stops at 7% during the installation the data.cab, I think maybe that's the same problem and it can not just write data to the hard drive.

  the freedos, which has been pre-installed no longer works (worked the first time). When I boot without the cd boot, I get a PXE - E61: Media test failure, check cable.

  do you think that the hard drive is just damaged?

  I can run ubuntu on cd, and did a small check it seems to be ok. but when I install ubuntu, after the restart, he went and I have to install it again (and again and again?)

  PXE - e61: possible hard drive error or a connector.

  Contact lenovo helpline for replacement free of charge if you have the warranty.

• How can I perform a clean installation of Mac OS x for my iMAC, retina 5K late 2014 with drive of Fusion with the intact Recovery HD partition?

  How can I perform a clean installation of Mac OS x for my iMAC, retina 5K late 2014 with drive of Fusion with the intact Recovery HD partition?

  Pure how to install OSX on a Fusion drive and keep the recovery disc function

  These instructions assume that your iMAC partitions or file systems has been damaged and you want to restore to the way most efficiency with fusion drive and the recovery partition, similar to what was built in the factory.

  These instructions work for the iMAC, retina 5K end 2014 version comes with OSX Yosemite. The scores of major drive of the 128 G SSD and 3 TB of HARD drive has been configured as a logical drive (merger by car).

  WARNING: These instructions here are shared for interest only. Readers to take their own risk by following these instructions. The author is not responsible for any damage caused by following these instructions.

  This is the target disk partitions, and the configuration that we want to achieve.

  Disk0 is the 128 GB SSD - solid state drive and holds the start of the partition (disk0s3)

  Disk1 is the 3.0 to HDD - mechanical transmission and holds the Recovery HD partition.

  There are two EFI partitions to partition table GUID on both hard drives (disk0s1, disk1s1).

  Disk space remaining (partition disk0s2 and disk1s2) are used to create the disc of Fusion 3.1 to named "Macintosh HD".

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage GB LVG 121.0 disk0s2

  3: disk0s3 Apple_Boot Boot OS X 134,2 MB

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk1

  1: EFI EFI 209.7 MB disk1s1

  2: disk1s2 Apple_CoreStorage TB 3.0 LVG

  3: disk1s3 Apple_Boot Recovery 650.0 MB HD

  / dev/disk2 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD + 3.1 TB disk2

  Logical volume on disk0s2, disk1s2

  0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

  Fusion unencrypted drive

  Here's how we do it.

  • A. clean reinstallation of Mac OS x.
  • 1. make sure that you back up all your data on the hard drive using Time Machine or other means. The following procedure will delete all data.
  • 2. create the OSX install USB, insert it to the MAC workstation.
  • 3. given that us will be operated on the internal trunk of the reader of the Mac, it must start on OSX install USB (see Y.).
  • 4. in the menu at the top of the screen, select disk utilities.
  • 5. turn highlighted the volume of disk Fusion called "Macintosh HD." Click clear to clean.
  • 6. If his success, then go ahead to install OSX new to that partition, as usual.
  • 7. otherwise, if it does not, that means fusion drive has been damaged.
  • 8 follow the instructions below to fix it.
  • . B. Split disc Fusion in the physical hard disks
  • 1. Since us will be operated on the internal drive of the Mac trunk, assumes that we already have boot up OSX install USB drive (see Y.).
  • 2. in the menu at the top of the screen, select utilities and Terminal.
  • 3. on the screen of the terminal type:
  • Cs diskutil list.
  • You will see something similar to the screen below.
  • 4 copy the long string after Logical Volume and replace the UUID with it in the following command to delete the logical volume of the disc fusion (aka coreStorage of logical volume):
  • diskutil deletevolume cs UUID
  • For example:
  • diskutil deletevolume E59B5A99-F8C1-461A-AE54-6EC11B095161 cs
  • 5 copy the long string after the logical volume group and replace the UUID with it in the following command to remove the drive (aka coreStorage) fusion:
  • diskutil cs remove UUID
  • p. ex. diskutil cs remove E03B3F30-6A1B-4DCD-9E14-5E927BC3F5DC
  • 6. at this stage, the fusion drive has been deleted, and hardsisk SSD and mechanical hard drive will be reappear in diskutil or separate records.
  • 7. If step 5 or 6 takes more than 30 minutes to complete, this means that the fusion drive has been corrupted. You can follow the commands below to clear the table to partition the hard way. First command clears the SSD drive, second command erases the HARD drive.
  • The command does not return a response, after 1 minute, press Ctrl + Z to complete orders. 1 minute is enough data to code and erase the partition table on the disk.
  • cat/etc/random >/dev/disk0
  • cat/etc/random >/dev/disk1
  • . C install a new copy of Mac OS x for the hard drive HDD and tested this disk partition hard recovery work.
  • 1. go on diskutil to create a partition called Macintosh HD HDD hard drive using all the space there.
  • 2 do the same with the mechanical hard drive.
  • 3. follow the usual procedure to boot from the installation of OSX USB and install a new copy of Mac OS x hard disk SSD.
  • 4. This will create the correct priming of the partitions, recovery hard drive partitions and PSX partitions hard disk HDD.
  • 5. once the installation is complete, test if OSX may start successfully, but no need to go through the initial MAC OS x didn't put in place that we're going to waste this and do the installation again later.
  • 6. we must now test if the recovery hard drive partition works.
  • 7. reboot for hard drive recovery (see X - by pressing command and R at the same time during boot right after that you hear sound start and release only a few seconds after you see the apple logo and the progress bar for loading...)
  • 8. it is important to test and make sure that the partition of hard drive recovery.
  • D. recreate the fusion drive
  • 1 since us will be operated on the internal trunk of the reader of the Mac, it must start on OSX install USB (see Y.).
  • 2. in the menu at the top of the screen, select utilities and Terminal.
  • 3
  . on the screen of the terminal type:
• diskutil list.
• You should find that we have a list of disk group hard physical volume only, no logic here still.
• 4. you will see something similar to the screen below.
• 5. search for the largest partition on the SSD hard drive, which should be close to the maximum size of HDD to the SSD (121 G, for example) and mark the name of the device, this will usually be something like/dev/disk0s2
• 6. search the largest disk partition mechanical forming fusion with the SSD hard drive. This should be close to the maximum size of the mechanical hard drive (for example 3 TB) hard disk and mark the name of the device, this will usually be something like/dev/disk1s2
• 7
. Now let's create the merger in car (group alias logical volume) in the Terminal, type: diskutil cs create nom_lecteur driveIDs
• The number of the driveIDs is unlimited, it may be a number of discs, or a number of disk partitions. Always put the faster discs first, for example for our SSD disk0s2
• For example:
• diskutil cs create fusiondrive disk0s2 disk1s2
• diskutil - the version of disk utility command line.
  cs - This calls for Core Storage, which is necessary for the merger.
  create - creates a basic storage group.
  nom_lecteur - is the name of the drive and how you want that he
• appear in the disk utility (not the Finder - that comes later). You can call it what you like; in our example, we named our Fusion table "Fusion".

driveIDs - Here is the Player IDs of the readers you want as part of your Fusion table, separated by a space. In our example, they are 'disk0' and 'disk1', but it may be different in your configuration.
• It is important that the faster hard drive appears first in the command, which in our case the disk0s2 (a partition in the SSD). In this way, drive fusion will use this disk as primary and the cache. The second disc in the command, in this case disk1s2 (a partition on the HARD disk). The secondary disk (HARD drive) is used to store less frequently used files.  Otherwise, the fusion drive performance will be worse that it is designed for.
• 8. you will see something like below appear on the screen:
• Creation Volume logical storage of kernel
• Move isk0s2 storage of carrots
• Disk1s2 of switching for the storage of carrots
• Waiting for logical volume group appear
• Discovered the new group of logical volumes 'DBFEB690-107B-4EA6-905B-2971D10F5B53 '.
• Store LVG UUID: DBFEB690-107B-4EA6-905B-2971D10F5B53
• Finished CoreStorage operation
• 9 copy to the bottom of the string after "Discovering new Volume Logic Group" using the command + C
• 10. next, create the partition of the merger (alias logical volume) drive named "Macintosh HD".
• In the Terminal, type: diskutil createVolume groupString jhfs cs + size volumeName
• For example:
• Diskutil createVolume DBFEB690-107B-4EA6-905B-2971D10F5B53 jhfs cs + 'Macintosh HD' 100%
• diskutil - once again, this is the version of disk utility command line.
• cs - called the basic storage functions, which are necessary for this arrangement.
• createVolume - this is the command to create the storage area real for the reader who is represented by an icon on your desktop.
• groupstring - this is the long alphanumeric string you copied in the previous step. It identifies the table you created such as getting a volume placed on it.
• jhfs + -the format of the disc. It is Apple (journaled) extended Format, which is recommended for drives with an operating system installed on it.
• VolumeName - the actual name of the volume, how it should appear under the icon. If there is a space in the name, you must put the full name in quotes ("name") or put a slash before the (name Drive\) space. In our example, we made these, naming our volume "Macintosh HD".
• size : this is the size of the volume. In our example, we had a 1.1 TB drive. We used '1100g' to describe what 1100 GB (1.1 TB to base 10). Otherwise, we could have also used 1.1 T or even 100% as a size.
• 11. go to diskutil to verify that you can see this new partition on the list.
• 12. test by erasing all the data from it.
• 13. then you can go ahead to start on the USB drive to install OSX and install a new copy of Mac OS x on it.
• 14. This will allow you to keep the recovery disk feature.
• X. how Prime to recover partition
• Press and hold the command and button R set immediately after hearing the bells to boot.
• Only release it 2 seconds after you see the Apple logo on the screen and the progress bar for the start. This will start the partition of hard drive recovery.
• Y. how-to boot OSX install USB
• Press and hold the command and the optionkey together immediately after hearing the ringing of boot.
• Only release it 2 seconds after you see the Apple logo on the screen and it will give you a list of startup disk choice, choose the OSX install USB to boot from.

• Do not click then that would start in a player flash for a clean installation of El Capitan.

  Bootable media created on a flash drive to do a clean installation of El Capitan on my MBP to Mid 2009. Once I'm booted up in the newly created disk, I can't click on anything in the public services. Chaotic strikes me disk utility, but clicking on does not. I can arrow up to my HD, but unable to select erase. To be clear, I CAN click around in disk utility when I'm booted up 'normally' in my HD. But when I restart, press the alt/option key and select the flash drive, I created for the new facility, click on in order to continue this process is not an option.

  First aid post ever. Hope that plays by the rules. Thank you very much!

  It's very strange behavier. Have you tried to clean your trackpad? Have you tried a wired mouse?

  Before you click to install flash player, the mouse was sensitive to other options?

• Clean installation recommendations?

  I made a post about this before, but it has been marked as resolved when someone suggested other methods of disk cleanup. Unfortunately, since then, the problem has worsened and I feel now that a clean install is the best option.

  I got my Macintosh since 2013 without no cleaning installs. My storage is extremely comprehensive. I have a 250 GB drive, but the storage page says I have more than 100 GB of space being occupied by 'others' that doesn't seem unreasonable. Part of the problem is likely to somewhat due to the multi-user system disruption.

  How can I do a clean install?

  Is it recommended to do with a time Machine backup? Any other suggestions or advice?

  Thank you

  Hello

  Help here > http://pondini.org/OSX/DiskSpace.html

  And here > OS X tips Display storage

  Keep in mind, OS X requires a minimum of 8.8 GB of storage space.

• My 2 TB TC is full and will not back up. Yet, I have only 1 TB of data on my laptop. Note that I've reformatted the laptop since the last backup with a clean installation of El Capitan.

  My 2 TB Time Capsule is full and will not save. Yet, I have only 1 TB of data on my laptop. Note that I've reformatted the laptop since the last backup with a clean installation of El Capitan.

  I bought a 2 TB external hard and have used Time Machine to back up. But I also use my time Capsule, which I save wireless.

  Any suggestions on getting my TC back up?

  One suggestion would be to copy all existing backups that are now on the Time Capsule 2 TB hard disk. Then, clear the TC and start over again with new backups.

  A more expensive option... assuming you want to keep all old backups on the TC... would be to add a new TC and start backups goes in this direction.

  Another option... If you do not need to keep all old backups now on the TC... would be to erase the TC and start over again with new backups. The benefit of doing this would be that no new material will be necessary, but the downside would be that you lose your old backup history.

• Re: Satellite U305-S7477 - problem with a clean installation of recovery disks

  I'm trying to do an OS clean installation of Vista on a new hard disk, the installation proceeds correctly, but in the end, instead of asking me to create a user id and password as the machine makes first start upward when it is new, it shows a login for the administrator with a message that the administrator account has been disabled , and enter another pre-existing user name and password, that I have not since this is a clean install.

  Toshiba wants to get only the recovery on top a pre-existing installation of OS? It would be quite a limitation and would prevent one to recover their machine after the death of a hard drive.
  Any thoughts? I look through the docs for a password by default, but if it's there I have not found it.

  Thanks in advance!

  Hello

  To be honest, your question is strange to me. The fact is, for the installation of an operating system you can use Microsoft DVD or DVD Toshiba recovery facilities. In both cases the installation is almost complete you must enter your user name and password (optional). There is no difference at all.

  I made repeated several times on WXP and Vista installation. No difference at all. Username must be entered always and I didn t notice such problem, as described in your ad.

  So please try to reinstall the OS and pay attention to every step of facilities. Images of recovery facilities are tested, and I can't imagine Toshiba s people can control something like that.

• came loaded with Windows Vista Home Premium. Recently, I reformatted the hard drive and did a clean installation of Windows 7 Professional. I have no games. No solitaire, Minesweeper, no nothing.

  original title: lack of games
  I have an Acer Aspire PC. It came loaded with Windows Vista Home Premium. Recently, I reformatted the hard drive and did a clean installation of Windows 7 Professional.

  I have no games. No solitaire, Minesweeper, no nothing.
  How can I, without seeking to erase and reinstall again?

  To activate the built-in Windows 7 games:

  1. click on Start (lower-left) and then on Control Panel.

  2. click on programs and features.

  3. on the left side of the screen, click on 'Windows turn features on or off".

  4. find the entry called games & check the box next to it.

  5. click on OK.

  6 reset.

  If the games box is already checked, uncheck the box , click OK, restart, then do steps 1-6 above.

• Upgrated dm4t-1100 with 256 GB ssd drive

  Hello

  I want to improve my storage unit with a 256 GB SSD:

  (a) 256Go crucial m4 2.5 inch Solid State Drive SATA 6 Gbps

  or

  (b) OCZ Technology 256 GB 4 Vertex Series SATA 6.0 GB/s 2.5 - Inch solid state drive

  1. number and product name

  Pavilion dm4t-1100

  2 operating system installed (if applicable)

  Windows 7 64 bit

   

   

  I updated the bios of my laptop via hp web page; and I don't know if there is a problem with high capacity ssd 256Go, could be a problem for this old laptop? I need to something another special update or a player?

  and that could be the best unit ssd ( Crucial 256 GB 2.5 m4 or OCZ Technology 256 GB Vertex 4 Series 2.5 inches)

  Thank you

  Hello

  Your laptop supports only the connection SATA II is a bit useless to buy any SATA III SSD that they will operate as SATA II disks. The service manual indicates that DM4 laptop support SSD 160GB drives, so all SSD should work as I do not think that the ability is a limit. OCZ, Intel, Corsair and a few others have good readers then choose one of the series SATA II of these manufacturers. I've seen some cases that a SATA III SSD did not work but a SATA II we did on older laptops. Maybe the newer controllers SATA and the old BIOS may cause some compatibility issues...

• After flashing my Bios on Pavilion DM4t-1100 CTO, I can no more enter the BIOS setup

  After flashing my Bios on Pavilion DM4t-1100 CTO, I can no more enter into the BIOS setup (via the ESC key).  I installed the BIOS twice and the computer always ignores the ESC key and launches Windows 7.  Any ideas?

  Well you're response made me experiment more and I discovered that the ESC key works if I type repeatedly instead pressed constantly.  Thank you for taking the time to answer!

• Renovated in car, Clean installation of Xp to 7 update does not.

  I bought a copy of Windows 7 upgrade to install on my machine. However, before that I had the chance to install it, my HD crashed. I've been blocked from buying a new drive. I was trying to run Ubuntu on it, I decided that I needed the Windows interface to my design work. (I use Adobe Indesign that does work very well with Linux) After formatting the drive, I went to reinstall XP to update 7 (due to the fact that my license will not allow for a clean installation). When I go to install Xp, it will not accept my license key that worked for her, until the previous drive crashed. Is there anyway that I can get XP to install so that I can update to 7 and with it, without having to buy another license for 7 or xp?

  You don't have a full version of Windows 7 from Windows XP to Windows 7.  You can use a Windows 7 upgrade version to perform a custom (clean) installation.  But you must have Windows XP installed and running first.  Details here:

  Windows 7 upgrade considerations
  Upgrade Windows XP to Windows 7

  Boulder computer Maven
  Most Microsoft Valuable Professional

• I will back up everything that I want to keep and do a custom (clean) installation for windows 7 Edition home premium.

  Amount of external hard disk space is required for installation files?   I have a 10 gig and a ceiling of 5 gig on my wireless devices, or am I better off buying the staples or office depot installation disc?

  Hello

  "do a custom (clean) installation for windows 7 home premium.

  You say you want to install Windows 7, NOT Vista.

  It is a better idea if you buy you the Windows 7 DVD and then install it from the media.

  You then save model the work of making a Bootable DVD from the download and you also then have a reliable way to reinstall Windows 7 and repair work on this, if you have the need to.

  Before purchasing Windows 7, make sure that your hardware and software will work properly with him.

  Take some time and these checks:

  Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

  If this is not available, Windows 7 will not properly work for you.

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Windows 7 upgrade paths:

  http://TechNet.Microsoft.com/en-us/library/dd772579 (v = ws.10) .aspx

  And the Microsoft Store where you can get an idea of the price of Windows 7:

  http://www.microsoftstore.com/store/msstore/en_US/list/CategoryID.50726100

  See you soon.

• Network card wireless upgrade dm4t-1100?

  HI -.

  I read a few threads asking if a specific card will work in this model, but I'm going to be less accurate. I have a computer dm4t-1100 HP laptop running Windows 7, it is the only Windows machine I have left and one of the reasons why I always use it to resolve WiFi issues with inSSIDer. The problem is the stock WiFi does that 2.4 GHz, and I would like to have a portable device that can run inSSIDer and do 5 GHz.

  Y at - it a replacement of WLAN card that will make A/B/G/N 2.4 & 5 GHz? (I'm sure that it's too ask

  If there is, can I replace it myself or is there a 'white list' or another problem, I will also have (read some of the threads that indicate this is a problem?).

  Are there "generic" cards, can I buy it from Amazon for it, or even only a 'white list' feature I need HP?

  Thanks for any help you can offer, I would prefer not to conduct just a USB that I tend to break or lose things like that.

  -Bruce

  Hi, Bruce:

  Here is the link to the service manual for your laptop.

  Chapter 3 lists the cards wlan supported with HP part numbers.

  http://h10032.www1.HP.com/CTG/manual/c03106715.PDF

  I do not believe that the adapter WiFi Atheros AR9285 802.11 a/b/g/n 2 x 2 is a dual card band even though it is listed as such.

  The parts store shows as a card bgn.

  So, as I see your choice is if you live in the United States...

  Broadcom 43224AGN 802.11a/b/g/draft-n WiFi adapter HP Part # 582564-001

  Intel® Centrino® Advanced-N + WiMAX 6250 HP part # 619997-001

  The only cards that work are those indicated in the maintenance manual and they must have the part number HP on them or won't work, because of the white list of the BIOS.

  I recommend buying a used but tested and working one on eBay by questioning by the part number.

  They can be had at bargain prices.