HP Envy Win 8.1

Similar Questions

• HP ENVY m6: boot image selected is not authenticated

  I need advice. "" When I turn on my laptop (HP ENVY, WINNING 8) computer I get the following message: "boot device could not authenticate press enter to ' when I have c: it stops. I can't boot into recovery mode either. What the hell went wrong?

  Well, I decided to bring it to the store from my friend, he is a technician and then of course he actually decided that he would start the operating system. He wasn't healthy but, we tried a refresh, but it stopped in the middle of it due to a disk hard w / the question. After that some of diagnotics hard drive was the culprit, so after a permutation we run once again. I'm fine w / start again as it works now. And I called HP ordered my backup disks. Thanks for the help, I would have had the discs that we would have come to the same conclusion I'm sure.

• Where to find the details of the Bios Update

  Hello

  I just updated my HP Envy/Win Bios 4.3 8.1.

  I would like to find a wepage where can I find details about the changes in each version of the Bios, a Web page that I can also use later for details of future Bios.

  Thank you.

  Hello

  I found the details of updating the current BIOS (F.43) under the software & drivers section for the TouchSmart from HP Envy m7-J010DX. There is no record of previous changes to the BIOS version.

  The information of the laptop is fn + esc and the label under the battery.

  Product name: HP Envy TouchSmart (TS) (fn + esc)

  Product name: m7-J010DX (label under the battery)

  Product model: E0K83UAR #ABA (fn + esc and the label under the battery)

  Product E0K83UA number accepts without the R #ABA part and form most suitable for this model number, however the E0K83UA lists a 1600 x 900 HD display, and the E0K83UAR #ABA has a full HD (FHD) 1900 x 1080 screen.

  Speculation: it is a refurbished model we HP, and it may be that the R indicates that it in the model number. The #ABA can be a qualifier of renovation indicating the State of the appearance of the machine after renovation, #AAA being the best.

  Thank you.

• HP envy 14-u009tx: help! need driver for wifi for win 7 64 bit

  Please help me,

  I was buy laptop, HP envy 14-u009tx

  original is using win8, but I am familiar with this os, so I'm going down for win 7 64 bit.

  Please someone help get this wifi driver. using braodcom.

  hardware ID here:

  pci\ven_14e4 & dev_4365 & subsys_2230103c & rev_01

  THX before.

  Hello:

  You need this driver:

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_133353_1#tab1

  You will also need this driver bluetooth:

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5405106 & swItemId = ob_132205_1 & swEnvOid = 4058

• HP ENVY x 360: HP ENVY x 360 Win 8.1 battery plugged not removable, does not support

  HP dear supporters,

  I have a HP ENVY x 360 laptop with Win 8.1 operating system. He writes that plugged in, not charging. This laptop has a non-removable battery. I read the forums and advice but neither solved my problem.

  I tried to close, plug off, wait, plug in, turn on, without result.

  I also tried to uninstal in Device Manager the baterries, then restart the laptop, without result.

  I also tried the fix for the problem with HP Support Assistant, digitization of the battery and he writes that my battery is ok, but then "unknown".

  I tried to download updates, no results due to "unknown".

  I'm not able to solve the problem of my laptop and I wouldl ike to ask for your help.

  I await your response.

  Kind regards

  @zsofiaanna

  Thanks for posting,

  If none of the latest articles helped.

  The best thing you can do is to try with another adapter with the same power supply.

  If the problem persists with the other cable

  To confirm if it is the battery or adapter that is faulty,

  The information, handy - contact the HP support by phone for a repair or dispatch part service (as applicable).

  If the information I provided was useful, give us some reinforcements by clicking on the solution and laurels, buttons that help and others see that we have the answers!
  Good luck.

  HP technical support are available by clicking on the following link:
  
  http://h22207.www2.HP.com/us-en/?openCLC=true
  
  (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.
  
  (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.
  
  (3) Once finished, click the "Show Options" at the bottom right.
  
  (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

• HP ENVY 750-055XT: HP download win 10 for win 7

  I bought a refurb unit. He came "upgraded to win 10 64.  But there is no win 7 files to restore.  I have a new win 7 64 pro license. On the CD.   How can I install and lose 10 WIN.  I want to have anything to with win 10 in the computer.

  I have the same computer with win 7 pro 64 installed. I have raid 1 disks.  If I removed the drive in the new computer and installed one of my raid drives which would solve the problem?

  I'll have one connected to the internet and the other will have my critical files and will not have internet capability.

  @HEMI7309

  http://support.HP.com/us-en/mediaorder/HP-envy-750-desktop-PC-series/7779687/model/7805186/softwareitem/M2H64AV/STEP1

  REO

• Envy 14 CTO will not shut, forces hard stop, after the upgrade to win 10 anniversary

  After a long wait in Win 10 the Envy 14 finally began to sleep and shut down properly. As soon as the update of the anniversary has been installed, we went back to the questions of the soul. System not completely stops and freezes to force a hard reboot, after that the restart that he stop or sleep is selected manually. If the system can accommodate on its own, then it is more closed or sleep without rebooting.

  Course on all drivers and troubleshooting power back shortly to all default values.

  Hello

  Try the following.

  Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

  In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, and then close the open windows and restart the laptop.

  When windows has reloaded, download the driver directly from Intel IMEI on the following link, unzip the and run the installer.

  https://Downloadcenter.Intel.com/download/26127/Intel-management-engine-consumer-driver-for-Intel-nu...

  Once the installation is complete, restart the laptop.

  When the machine rebooted, re - activate the quick start and restart the computer once more - let Windows take over completely for a few minutes before checking.

  Kind regards

  DP - K

• HP Envy M6: My HARD drive is not bad on my computer? I have reloaded Win 8 and upgraded to Win 8.1 but he keeps crashing

  Hi need help and answers from an expert!

  My HP Envy M6 Recenly has stopped working correctly, so I decided to recover as soon as possible.  She still had the same problems, so I decided to restore factory with recovery USB flash drive I did.  Always had the same problem happens after I rebooted 8 Win and improved to 8.1.  It would work for a few minutes and stop working I used chkdsk and it says it fixed a few problems with the drive.

  I went through the same steps another 3 times!  After each time that once I had that he would be running again after a clean reinstall.  I would like to run chkdsk and it looks like he fixed some error, but last time, it wouldn't or couldn't find some files to run and crashed.  I tried loading Acronis and tried to reinstall the backup from there but that also failed to correct the problem.  I came to the conclusion that my HD is physically wrong?

  I guess the recovery process would reformat the partitions before you reinstall so it's not a logic error (software)?  From the recovery partition, the recovery Flash disk media and recovery software acronis can fix this, I can only assume, there is a problem with the drive itself?

  Is there a way to check this?  I don't mind replacing the drive to a SSD, so this isn't a problem, but I can't seem to find a product key.  Nothing printed on the bottom.  I read somewhere that it is now integrated with the motherboard bios so can I just use the recovery media that I did on a flash drive?

  Also, I have my backup file but I could never find the location of the image my wife loaded as the photo of "lock" screen which I do not have a copy of.  I have the backup files for windows 8.1 by Acronis and according to me, a Windows backup file on a backup drive, but I was wondering if these "locked screen hidden image" would be held somewhere in these data?  It is not under the images and I have never been able to find or understand where windows keeps this image.  I used the search without success.

  Of course, this is not critical, but I hate losing this particular image.  I hope it's keep somewhere in my back upward and when restoring with a new drive hard I can reload the backup and restore.

  So I really ned knowledge step by step: my HD is bad?  How can I check without having to spend hours to reload only to fail?

  Why chkdisk does not?  Or should I simply replace HD and if so what can I use the new disk recovery media and product ID will be accessible through the motherboard?

  I intend to upgrade to win 10, but I need Win 8 loading first, then move to 8.1 then move to Win 10?  Also in the future if it crashes how can I recover to win 10? Since it is free now but will not be later.  The upgrade will allow me to make a copy (a copy) to win 10?

  A lot of questions, but please provide the fastest solution to my problems and concerns.

  Thank you in advance!

  FM Hawaii

  Hello fmhawaii ;
  
  I read your post on your PC crashing and wanted to help.

  It certainly seems that your hard drive has failed.  Some PC allows the drive to check in the BIOS: test a hard drive in the BIOS. HP® customer support

  If that confirms that the disc is bad, then you will need to replace it.

  As for activation, you are right in that, with Win8x machines, the product key is embedded in the motherboard UEFI firmware, however, the instructions in this link, show you how to recover: find product - key for Windows 8

  When you restore from recovery media, which is supposed to automatically read product key, so you will not have to enter something to activate reinstall it.  My guess is that the drive problems that prevented from happening.

  Acronis allows you to mount an image file by using a drive letter, and once you do this, you should then be able to browse through the content to find the file you want.  However, depending on what part of the logon icon changed, it might be embedded image in a Windows system file, and unless there is a separate copy of this image, it will be very difficult to recover.  IF you Google it, you might be able to find downloadable tools for disassembly of this file and subseuent extraction of this file.

  I wouldn't hurry to Win10, but if you choose to follow this path, don't forget to make a new advance Acronis backup, then you can return to a system of Win8x of work if something is wrong - as the Win10 GoBack function is known to be unreliable.
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• HP ENVY M6 1254eo help me to find the correct drivers (lowered the victory note 8 for win 7)

  I bougth an HP ENVY M6 mobile 1254eo today, but I strongly dislike win 8 so I immediately spent to win 7.

  The problem is that I find that no driver for win 7 is associated with this model, at least not on any other technical support site of HP that I searched.

  Are there drivers available at all, and if so could someone direct me to them?

  Hello:

  Use these drivers for the Ethernet controller.  3rd file down on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1 & PNid = 13 & PFid = 5 & Level = 5 & Conn = 4 & DownTypeID = 3 & getdown = false

  Network controller:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 321957 & prodSeriesId = 5379211 & prodNameId = 5379212 & swEnvOID = 4058 & swLang = 13 & mode = 2 & taskId = 135 & swItem = ob-122653-1

  Bluetooth:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 321957 & prodSeriesId = 5379211 & prodNameId = 5379212 & swEnvOID = 4058 & swLang = 13 & mode = 2 & taskId = 135 & swItem = ob-119299-1

• Wireless network adapter for HP envy ultraboook 6, 1011TU - Win 7 32 bit

  Hi Please help share the network drivers for the HP envy ultraboook 6, 1011TU - Win 7 32 bit as well as my brightness key does not support after I changed my system to Windiws 7 and removed from Windows 8.

  Please help.

  Hello:

  You need this driver...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-107849-1&cc=us&DLC=en&LC=en

  You will also need this bluetooth driver...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131427-1&cc=us&DLC=en&LC=en&OS=4063&product=5273547&sw_lang=

• HP ENVY at Quad Win 7 bluetooth adapter

  Hello

  I have problems to activate BlueTooth on my new HP ENVY 15 t Quad with Win 7 Pro 64 installed OS.

  The laptop is equipped with a card 802.11b/g/n WLAN [1 x 1], Device Manager indicates this device as a 8188EE Realtek RTL 802.11bgn Wi - Fi adapter. Apparently (Internet sources) this map is compatible Bluetooth.

  However - Device Manager tilts not Bluetooth and I can't find how to activate Bluetooth on this laptop, Wi - Fi, very good - but not Bluetooth functions.

  So:

  8188EE Realtek RTL supports BlueTooth?

  If so, how can I activate it?

  Thanks, if I wouldn't contact the support to do this.

  Yep, that is...

  Here is the link to the service manual for your HP ENVY 15 t-j100 Quad Edition CTO Notebook PC.

  http://h10032.www1.HP.com/CTG/manual/c03943414.PDF

  Chapter 3, page 23 lists the supported cards wireless and wireless/bluetooth combo with their HP part numbers.

  Chapter 5, pp 44-46 rprovides the WLAN card R & R procedures.

• HP dv6 Envy: how to stop the automatic installation of 8.1 to win on HP Envy laptop?

  My laptop HP Envy has automatic update downloaded to Win 8.1. He saysit will install on the next reboot. How to stop this instsall?

  PSKROBACK wrote:
  

  I didn't upgrade because I read several reviews that said if you didn't have a touch screen that you would have difficulties to navigation in some applications. What apps not said.

  What you say makes no sense and I question the validity of these comments.  Update to Windows 8.1 will do more good than harm.  Very few people who have updated have experienced problems, so comments to keep your receipt no logic.

  Here's something you can do.  Download Macrium reflect free and create a hard disk image on an external hard drive, don't forget to create the rescue disk.  Once done, update your system to 8.1.  If you have any problems, then you will be OK.  If it doesn't work or you have problems you can restore the backup of the image on your system that will put the computer to Windows 8 with no ill effects.  An image backup of your system from time to time is the best thing you can do.  You will have no problems with the help of recovery disks, reinstalling programs and data.  Many people use this method and have no regrets.

  http://www.Macrium.com/reflectfree.aspx

  Don't be afraid of it, it is a very useful tool.

• HP Envy 17, Win 8.1 and Win7 dual boot

  Please direct me to a good installation step by step of win7 on a preinstallation 8.1 Win...

  partition are ready 500G each, but the problem is my misundertanding of the MBR and UEFi, GPT partition.

  I won't an expanation of terms, but a way to boot and install WIN7 and Win8.1 in the dual-boot.

  Thank you. im not computer dumb.

  Mitch

  Your laptop of HP ENVY 17-j150ca is basically the same as my computer laptop HP ENVY 15 t-j100 CTO, only bigger. You will need to provide the Intel AHCI / RAID drivers during the first part of the installation. Please download "f6flpy-x 64.zip" of Intel Download Center. Expand this and place the file/folder on a USB key. Then;

  (1) DISABLE "Secure starting" and ACTIVATE the standby mode 'legacy' in the BIOS. Save and EXIT

  (2) enter code as it is necessary to recognise the change

  (3) reboot and press 'ESC' and then 'F9' when prompted. Select "UEFI - CD/DVD" or "UEFI - USB key... and boot from the DVD of Windows 7 SP1 or a USB key.
  4) click install now
  (5) to accept the license agreement
  (6) when the option to select an installation type, click (custom)

  (7) there will be a link called it loads drivers, insert the USB stick with the Intel AHCI / RAID drivers, select the USB and it should load the appropriate driver.

  (8) continue the installation by following all the guests... BE SURE TO SELECT THE PARTITION NOT USED FOR INSTALLATION

  Good luck

  Most of the Windows 7 drivers for the TouchSmart from HP ENVY 17 t-j100 CTO Notebook PC drivers of Quad Edition page should work on your computer.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Envy 17 t N100 CTO: go win 10 to 1 TB of HARD drive to new SSD

  Hello

  I just bought a N100 Envy 17 t. CTO notebook I need to installed Windows 10 of 1 TB of newly installed SSD HARD drive.

  The SDS will be for OS and 1 TB of storage can I transfer or need to win 10 disc. The make or create recovery disk disk of 1 TB of HARD drive?

  I win 10 portable old upgradeon but the disk is full.

  Thanks John

  I would use minitool partition manager to clone the disk partition & 100 MB windows C if your installation.

  Works well in general & used for this task a lot. Use the partiton options rather than SSD clone will enable driving a complete copy of all of the source to the target SSD. Don't delete anything since! TB until what you tested SSD clone A1.

  I'm Manager of minitool partition on a usb drive boot as a practical tool great & free tools menu

  http://www.MiniTool.com/partition-Manager/partition-Wizard-home.html

  http://www.MiniTool.com/partition-Manager/partition-Wizard-bootable.html

• Driver Bluetooth for hp envy 17-j100 ee win 7 32-bit or 64-bit

  Dear Sir

  I'm looking for EA for hp envy 17-j100 bluetooth driver for win 7 32-bit or 64-bit, I don't find it on the site of hp adapter? can you please guide me where to download

  Here is the site of product drivers

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=6884...

  Try this driver...

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_130390_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken