HP psc 1210 aa in a printer

Similar Questions

• HP psc 1210 all-in-one printer: HP PC all-in-one printer

  Printing test page fine.  Prints the first page of the document very well.  After than that, each page becomes lighter and blurred until unreadable.  This "bad s.  Printer is several years old and has been the impression so far.

  Hello @bdr777,

  Welcome to the HP community!

  I hope you have a pleasant experience here.

  I would like to help with the discoloration print issue you have with your HP PSC 1210 all-in-one printer, when printing from your computer Windows 8.1.

  Could you try to make 3 copies of something on the printer for me? If the three pages of fine print, then we know that the problem is related to the software on your computer. If the pages are starting to fade and blur, then we know that the problem is probably with the printer cartridges.

  Are the cartridges you use genuine HP? Can you check the date of guarantee on them for me if they are? If they are relatively old cartridges, the nozzles down can be a bit clogged and start getting muddy upward while you print. (This is particularly likely if you use the printer very rarely).

  If copies are still faded and blurred, try these steps to clean the cartridges:

  1. Open the all-in-one with the power on and then remove the ink cartridges by slightly pressing the cartridge while pulling gently toward you.
  2. Inspect the ink cartridge ink nozzles and contacts for the accumulation of debris and ink.
  3. To clean build-up, dip a q-tip in distilled water (or water if distilled water is not available) and press the remaining water from the swab.
  4. While now the cartridge by the sides, as shown in Figure 3 below, gently wipe off any buildup of debris.
  5. Reinsert the ink cartridges and perform the alignment of ink cartridges.
  6. Print a test page to check the ink cartridges and rinse any remaining accumulation of the nozzles of the cartridges.

  

  -Source

  If the copies to print without any problem, try to download the HP printer installation wizard to make sure you have the latest drivers for your product.

  I hope this helps!

  Please reply to let me know if we have solved the problem.

  

• Jam paper error message hp psc 1210

  I got a paper jam on my printer hp psc 1210, but, unfortunately, the printer will not be shared the error state and will not be printed.  When I run the troubleshooter, it indicates that this is no problem.  I turned the power on, I unplugged then replugged the printer, but nothing works.

  Thanks, Shane!  I had seen this article and tried several of his suggestions to solve my problem without success.  So when I started my laptop and the printer running this morning, he is animated and printed the document that should have been 'stuck' in the queue.  It would seem that I have a "gremlin" printer that will taunt me regularly until I have give up and replace this printer 8 years!  I appreciate your quick response!

• HP psc 1210

  I get lines destorted when printing sheets XL spread.  I use windows 7 and HP psc 1210 all-in-one printer.

  Especially the verticle lines and a few horiz. printing width lines HTS.

  Thanks for all your replies.

  It seems that I have Office 97, which is not compatible with Windows 7

  so I think that I just bought a version of the layer.

  Jack

• Printing problems HP PSC 1210 since upgrading to Windows 7

  Hello

  Unfortunately, I have major problems since upgrading my PSC 1210 previously hassle to Windows 7 Professional (32 bit) on a Dell Latitude laptop.

  1. connect the USB cable from the system causes to restart almost 100% of the time. (Start with her already plugged the same result.) If it restarts not who does not necessarily mean that it will print. Although the USB connection is identified, the document does not print and gets stuck in the queue; by selecting either restart or cancel in the print queue does not delete it. Or turn off and unplug the printer. I have to restart my computer for him to clear, but it still doesn't work. Also, it gets stuck when I choose to print directly to the printer. More recently, I've only managed to print after closing of all the HP of the process in the Task Manager. (The same problem with restarting forced to plug in the USB cable happens sometimes when the analysis rather than printing).

  2. on the occasions I manage to do print documents, does not print black cartridge, despite having just replaced the cartridge and the perflecty black print on the test page.

  I hope you can help because it's incredibly frustrating and tedious, and I really prefer is not to have to replace what was until what Windows 7 a perfectly good printer!

  Thank you

  Olivia

  Welcome to the Forums of HP savemysanity,

  I see by your post that when the connection of the USB cable, the computer restarts, the print jobs stuck in the queue since the upgrade to Windows 7, the black is not printing from applications, but prints black on the self-test page. I can help you with this.

  Run all the updates of Windows on the computer. Updates Windows Installer in Windows 7

  I have provided a document through the steps to see if this will solve the problem.

  Print jobs are stuck in the print queue.

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically.

  Run the System File Checker. This utility allows users to analyze and restore corrupted Windows system files.

  System File Checker: run sfc/scannow & analyze its logs in Windows 7 | 8.

  The chkdsk command or "Check Disk" utility is used in Windows to browse your entire hard drive and find problems.

  Run the Chkdsk utility.

  Try another port on the computer and another USB cable just to exclude.

  If the problem persists, would completely uninstall and reinstall the printer software.

  Uninstalling the printer software.

  Installation of the software of the printer in Windows 7 for a USB cable connection.

  There is no driver to download, drivers are drivers from Windows Update.

  What operating system go you to?

  If you need help, let me know.

  Good day!
  Thank you.

• PSC 1210 not printing anything

  According to the title - no problem, put on the market, no led error, tried to print, sheet produced but empty.

  I replaced both cartridges - still nothing, no alignment sheet (not even a void) does not produce but now "Check print cartridge" flashes.

  When checking the properties of the printer, I learned "the device is functioning properly.

  All I can think is perhaps the need for cleaning nozzles, but I can't find the tab "maintenance".

  Properties of the printer to try it. Please let me know where this can be found most any other suggestions

  as to what might be wrong.

  What about John

  Hey @Johnandberny ,

  Thank you for taking the time to post on the HP Forums today! Hope you enjoy the experience.

  I understand that you are getting the "Check print cartridge" light on your HP PSC 1210.

  Here is a document that addresses all the light on these series of printers. Please take some time, click on the links of correlation in the body and follow the steps in the solution.

  Flashing lights on the printer series all-in-one HP PSC 1200, 1310, 1340 and 1350

  Have a great day! Hear from you soon.

• My HP PSC 1210 Al lin One xi does not print the small print on a soup Plantation coupon

  My HP PSC 1210 xi all in one printer does not print the small print on a soup Plantation coupon. I was able to print very clearly a letter that I had written and recorded in the notebook. Printing in Notepad is quite small, but it is still much more that the small print in the coupon which wouldn't not print... I printed these coupons several times before without a problem. Also, the small print very clearly appeared on-screen.

  Ron Nimmo

  Hello

  1. do you get an error message? If Yes, what is the exact full error message?

  2. are you trying to print online or that you have the coupons saved on your computer?

  3 If printing online, what web browser do you use?

  4. is the specific question about the site?

  Follow the article:

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  If still the problem continues contact HP support for help.

  http://h10025.www1.HP.com/ewfrf/wc/product?cc=us&LC=en&DLC=en&product=90767

  Hope the above information is helpful.

• PSC 1210 all-in-one: hp psc 1210 order copy but scan and print

  Until recently the copied PSC 1210, scanned and printed.  It copies is no longer in black & white, or rather when I press the copy button, the scanning starts and the printer prints a blank page.  Without moving anything, I can scan the document (Windows Fax and Scan) and print it using the same PSC 1210 and it prints perfectly.  A color copy prints a few characters in blue/green.  No recent change in hardware or software (other than the Microsoft updates).

  Hi @will-not-copy,.

  Maybe the problem is related to the ink, especially the black ink. If I understand your description that you can scan and print again, but you are unable to copy. Copying and scanning use the same hardware components so ideally if we work so should the other. Copy and print using the same ink system so if you can print, you should be able to copy; However, the impression of the computer may produce a composite black, which means that the colors combine to make black, when copying the printer can pull out the black cartridge to produce black. That's what I mean when I say that the problem might have something to do with the he black cartridge.

  I would like to print a self-test report to see if the printer hardware can produce black ink in stand-alone mode. To print a report, use the following steps:

  1. Load the plain, white paper into the paper tray.

• PSC 1210: PSC 1210 print very slowly

  Printer prints very, very slowly.
  Self-test page took 96 seconds.
  Test printing to HP PS RD took 05:34.
  I've tried everything recommended on the support site.

  In addition, with the regular docs (Word or PDF) it will print 1st page very well,

  then slow down waaaaay.

  The next page will take more than 10 minutes and out very light.

  I am convinced that it is not a problem of ink that I just replaced both cartridges.

  Thanks for any advice you have.

  The printer made a tape from the printhead, then pause for about 15 seconds before the next swath?  This is probably caused by the failure of one of your cartridges. I don't remember if the PSC 1210 supports printing with a single cartrdige, but try the following: remove the black print cartridge and print a test page.  The printer prints at a normal speed?  Is therefore the black cartridge was the issue and needs to be replaced.  If it isn't then, put the black back cartridge in and remove the color cartridge and the test page printed.  If the printer now prints speed the color cartridge is responsible and must be replaced.

• HP psc 1210 printer v all-in-one

  I'm missing a driver for my hp psc 1210 printer v all-in-one.

  I can't print from my desktop pc to Windows 7 on my printer.

  Printer works very well to plug into the wall for printer - will make copies just fine.

  Computer added my default printer - that part is fine.

  When I try to print from the computer to the printer, I get a message saying the printer is waiting for 1 document waiting to print, but it will not be printed.

  I tried to unplug the USB cable and plug it into another USB port, but it does not work either.

  Tried the Printing Troubleshooter?
  http://Windows.Microsoft.com/en-in/Windows7/open-the-printer-Troubleshooter
  If this does not help, try this procedure by Arthur Li [MSFT]:
  Clear printer spooler files and activate the Spooler Service
  =================================
  1. click on start, type "Services.msc" (without the quotes) in the search box and press ENTER.
  2. double-click on "Printer Spooler" in the Services list.
  3. click on stop, and then click OK.
  4. click on start, type "% WINDIR%\system32\spool\printers" in the search box and press ENTER, remove all files in this folder.
  5. click on start, type "Services.msc" (without the quotes) in the search box and press ENTER.
  6 double click on "Printer Spooler" in the Services list.
  7. click on start. In the Startup Type list, make sure that "Automatic" is selected and click OK.

• Unable to print from the Internet using HP printer psc 1210

  Original title: hp psc 1210 printer xannot can be identified by my laptop Viao soni

  I'm unable to print from the internet. This problem has not occurred before.
  What should I do or change the setting to be able to print again.
  Thanks for your help.
  Darius
  

  Hi Nicolas,.

  This problem may occur if the printer driver is corrupted, outdated or incompatible.

  1. what web browser do you use?

  2. the problem occurs with all web browsers?

  3. deal with any problem while printing from the computer?

  4. do you receive any error messages? If Yes, what is the exact error message?

  Method 1:
  I suggest you try the procedure described in the article, if you are using Internet Explorer 9.

  You receive a script error and are unable to print from Internet Explorer 9
  http://support.Microsoft.com/kb/2652062

  Method 2:
  If the problem is not resolved, I suggest you try the procedure described in the article and see if it helps.

  I can't print or preview before printing a Web page in Internet Explorer
  http://support.Microsoft.com/kb/973479

  You can check the link for more information:

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• PSC1210: HP PSC 1210 erro

  'Paper jam' error in the status of the printer from the PC even if there is no interference on the printer paper.  I can send a print to the queue file, but it would not print.  Any help would be appreciated.

  Evening @shark3fins.

  I saw your post about the problems you are having with a paper jam error message on printer PSC 1210 and I am able to help.

  There are only a few documents left for this model of support, but I found this fixing of jams paper or workflow issues paper for printers from the HP PSC 1100, 1200, 1300, 1400 and 1500 series.

  Please note: the printing software will not send the print job on the printer if he thinks it's an error state. After checking the good printer, try to make a copy. If it copies, it may just be a software problem, you can always try Uninstall and reinstalling new software this download page.

  Please let me know if any of these steps has resolved your problem, or if there is anything else I can do to help.

  I look forward to hear from you!

  Thank you

• Scanning with PSC 1210

  Anyone know if I have all the installed ink cartridges in order to use the scan function?  Someone has just given me their old printer, but with no ink.  I tried to analyze something with a Brother MFC 420CN, but he would do nothing until all the ink cartridges have been installed.  I've never printed in color, so this is not a useful option for me.

  Also, the PSC 1210 is compatible with Windows 7?

  IIRC, this printer can print with only 1 cartridge. If you insert only the black cartridge, it prints ink backup mode.

  As for Windows 7, it has built-in drivers for PSC 1310. So he just plug the printer to the PC and run Windows Update, and it should install the drivers.

• Check the HP PSC 1210 ink levels

  I have a HP PSC 1210 with a HP Pavilion G6 running Windows 7.  How can I check my ink level? It used to be the HP Toolbox, but that has disappeared. Thank you

  Look at this link here on the frequently asked questions for the upgrade on this printer to the Windows 7 driver installation. Some advanced features are not available. The Toolbox of the printer has a workaround solution to check the estimated ink levels.  There are two listed. Under the frequently asked questions, click the sign of "HP Toolbox workarounds", it's towards the end of the page. There are also some great info in the FAQ for the solution also Center.

• 'Fit to Page' does not work with HP PSC 1210

  my printer is a HP psc 1210 all-in-one and the button to 'fit to Page' size rarely works to enlarge. Waste paper, she works more often correctly on photographs. Is there some MACRO instruction that will work properly. My computer has the Director of H - P program on it, then change it to late changes (like Google Chrome), the window does not work correctly.

  Moved from feedback

  Original title: impression of the printer

  My system is Windows 7, 64-bit

  You are running Internet Explorer 8 (IE8), IE9 or IE10?

  PS: I would be very surprised to hear that the all-in-one HP PSC 1210 has worked on a Vista computer running IE9, and still less a computer Win7, IE9, IE10, or (God forbid) IE11 Preview!