HP2000-2D11SX: I WANT TO LOAD WINDOWS XP ON MY HP 2000-2D11SX

Similar Questions

• I was struck with a person supported my mail to send spam messages! your also filled my 233 c/GB HDD if I can get things working I want to load windows vista

  I was struck with a person supported my mail to send spam messages! your also filled my c/hard drive 233 GB! If I can get this thing works and cleaned I want to load windows vista thank you, Pat

  I was struck with a person supported my mail to send spam messages! your also filled my c/hard drive 233 GB! If I can get this thing works and cleaned I want to load windows vista thank you, Pat

  Hi Pat. You need to change your password of e-mail of course but not in front of you, either remove malware from your computer or format and install Vista. Exactly what the problems are, other than your email, you encounter? What do you mean also 'filled my c/hard disk 233 GB'? Please give as much detail as possible.

• Compaq Presario CQ40 - 100 CTO Notebook (you want to load Windows Xp... Bluw error screen)

  I want to load windows Xp on my notebook Compaq Presario CQ40-100 CTO Notebook PC
  I already have vista on it
  When I try to install windows xp using boot able cd I get an error each time blue screen

  PLS help me... .i want to load windows xp on my laptop

  No. F2736PA #ACJ

  Serial number. CND84502BQ

  Compaq Presario CQ40-100 CTO Notebook PC

  Make your Vista recovery cd/DVDs if you have not yet discovered it here

  Your model should ICH9 sata driver sliptreamed in the installer CD of XP. If you did it right, you'll BSOD error.

  Use Nlite to sliptream ICH9 sata driver.
  A good guide for driver sata sliptream, here

  Note: do NOT use this guide sata driver, your sata driver is below ICH9.

  ICH9 sata driver,

  The pilot lies in iaAHCI.inf and is called ICH9M-E/M SATA AHCI Controller, here

  Download nLite, here

  Some suggestions to avoid problems when installing XP:

  1 try NOT all wake sata drivers, use only ICH9--> ICH9M-E/M SATA AHCI Controller

  2. use of XP - SP2, much easier to use since many XP drivers were built based on XP - SP2.

  3 burn the installer of XP slowly and do not use the maximum speed, sometimes it create errors

  4. choose a reputable support CD, not the one at little cost.

• When I run mozilla or open a link in a new window but I get the page you want to load an additional page of the new tab opens with it, the difficulty?

  When I launch mozilla or open a link in a new window I get the page you want to load but an additional page of the new tab opens with her. I tried to change my homepage to different things (new tab, firefox home, see the blank page) but I always get a new additional tab to open. How can I get only one page to open it?

  Hello

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  
  Note: This will make you lose all the Extensions and preferences.

  • Sites Web open is not recorded in less than 25 versions of Firefox.

  To reset Firefox, perform the following steps:

  For Firefox versions prior to 29,0:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the "Reset Firefox" line

     

     button.

  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  For Firefox 29,0 and above:

  1. Click the menu button

     

     click Help

     

     and select troubleshooting information.

  Now, should open a new tab containing your troubleshooting information.

  1. At the top right of the page, you should see a button that says "Reset Firefox"

     

     . Click on it.

  2. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  3. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

  Thank you.

• My wife down loaded window 8. But I want to reinstall vista 32. No cd. but I have the product key.

  My wife down in 8 loaded window, but I want to reinstall Vista 32. (not), but I have my product key.  I need help!  Thank you

  Hello

  There are several methods to reinstall Vista.

  There is no Windows Vista downloads available from Microsoft.

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall Vista from how you bought your computer, IF the 8 Windows Installer do not wipe it.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• How can I get a new serial number for my 11 elements that I want to load on my new Hp envy touchsmart pc running Windows 10?

  How can I get a new serial number for my 11 elements that I want to load on my new Hp envy touchsmart pc running Windows 10?

  Hello

  «If you have purchased a license for Photoshop/Premiere elements 11 and saved in (http://adobe.com), that you can sign in here and get the license key of series under "" manage account > Products and Plans > my products "»

  If you purchased a volume for Photoshop/Premiere elements 11 license, then you can connect to Volume Licensing Adobe website (http://licensing.adobe.com/) to access the series to activate license key product. You can access the link as follows to download the installer of Photoshop or Premiere elements 11.

  Download Photoshop Elements | 10, 12, 14, 11, 13

  Download Adobe Premiere Elements 14, 10, 11, 12, 13

  You can also access the link as follows for details how to access the serial key.

  Find the serial number of your Adobe product quickly

  Thank you.

• I need to display a corporate tutorial site which is only supported by Microsoft Windows.  Is it possible to load windows on an external hard drive and a MacBook to view the Web site?

  I need to post a tutorial for some training company corporate site only supports Microsoft Windows.  I'll buy a MacBook in the coming weeks when I go to training and I wonder if there is a way to load windows on an external drive and launch it on my MacBook?  I know you can use bootcamp, but I don't want to burn up that much of my Flash memory by placing it on the MacBook itself.  I have a 1 to Seagate that I use on my iMac at home for Time Machine.  Could just operate with Windows on it to visit the society tutorial with my MacBook?

  Boot Camp will not allow that.

  It is possible that one of the many emulators Windows for Mac can allow you to run with such a disk configuration.

• Help, please! computer HP laptop g72 does not load windows

  I can't get my laptop to initialize. I was it clean and running virus/spyware scans when it overheated and judgment (something he seems to do more in more often lately), I came back to the room to check on it and he stopped. He gave me the usual message about how he had disappeared in hibernation because the internal temperature exceeded blah blah blah (don't remember exactly what he said, but it wasn't the basics of it) now normally at this stage it will restart and be well and I can continue with what I was doing before. However this time it will not go beyond the second screen. It's what he does... (I will include the information in the end system)

  I press the power button then screen shows the following

  1 HP screen of the logo with the message "Press ESC for Boot Menu" at the bottom left then flashes to the next screen.

  2. starting Acronis Loader...
  Press F11 for Acronis Startup Recovery Manager... (horizontal cursor flashing after...) then flashes to view the first screen again

  and this process is repeated again and again until I got disabling or press ESC to #1 screen or F11 to the screen #2 how it will load either the menu start screen where I can access info sys diagnotics, BIOS or system recovery system.  or Acronis where I can make backup dics or start the Recovery Manager (who I'm trying to deal with the system if that is possible at this time because there are pictures and things on the hard drive that I want not deleted if it can be avoided)

  the process is normal to start but after #2 it should be blank with blinking cursor and then begin loading windows... I cannot at this point. He repeates just the first two times, I let it run for about 10 minutes at a time to see if she would do anything else, and it won't.

  System info-

  portable mode: HP G72 notebook PC (not sure what particular model because I don't know where to find this info)

  System ID: 1425

  Product number: LE846UA #ABA

  Warranty start date: 27/03/2013

  BIOS date: 08/11/2010

  BIOS version: F.26

  Processor type: Intel Pentium CPU [email protected]

  Processor speed: 1866 MHz

  Operating system: Windows 7 premium 64-bit

  I bought this computer used. The battery has never held a charge, I've always had it up to use it, but I don't know if I had to buy a new battery it would probably work. I never had the money to make and never really needed it so never bought.

  I tried to access the BIOS and it requires system administrator password. I tried to enter my password that I used to connect to windows, but that did not work. After 3 tries I have a message to disable the system with [6207076] below.

  Is there someone who can help me to fix it?

  I really don't want System recover unless there is a way to access the LIBRARY (documents, music, pictures) if I can help it. I don't have the ability to transfer all of my photos from my other computer before that happened.

  Please help me!

  Hello

  The code below should allow you access the bios menu:

  76165078

  Once, I would like to delete the password entirely - use the arrow keys to select the Security tab and press ENTER.  Use the arrow keys again to select the admin password option and press ENTER.  Enter the current password (use the above code), and then for the new password, just leave this blank and press on enter – do the same for the confirmation field.  Press f10, select this option to save the new settings and press to enter.

  Once completed, boot into the bios menu and reset the default settings - it may also be useful running a quick diagnostic on the HARD disk and the memory that is to be found under the Advanced or the diagnosis tab.

  Kind regards

  DP - K

• Windows 7. But the name of the account user each time before fully loading windows. How can I stop this and simply load in thank you Windows.

  I have just upgraded to Windows 7. But whenever I turn on my computer, he wants to support me on my user account name before completely loading windows. How can I stop this and simply load in thank you Windows.

  Hi UKuser7,

  Welcome to Microsoft Answers Forum.

  Automatic logon is disabled in Windows 7 by default for security reasons. If it is enabled, anyone who can physically access the computer can also gain access to everything on the computer, including the networks that it is connected.

  This setting is only recommended for cases where the computer is physically secure.

  To set up Windows 7 to connect to the desktop automatically, follow the steps below.

  1) click Start , and then enter the following command in the start search box:

  Netplwiz

  2) press ENTER.

  This opens the Advanced user accounts Control Panel window.

  (3) in the users tab, uncheck the box next to users must enter a user name and password to use this computer.

  4) click apply at the bottom of the user accounts window.

  (5) when the newspaper automatically on the dialog box appears, enter the user name for which you want to automatically connect to Windows 7. Then enter your password in the two areas where it is requested.

  6) click on the OK button.

  7) click OK in the window user accounts to complete the process.

  Thereafter, your PC at startup, Windows 7 will be automatically connect.

  Ticket back for your comments and concerns.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think

• I want to install Windows XP on my iMac, but I can't find the installation CD. Is it possible to get another disc, since I already have the product key?

  I just bought an iMac and want to install windows xp on it with bootcamp. I want to load all my old files, photos, etc. on the Mac. I have the product key but cannot find the installation cd. Is it possible to get a cd without having to buy the whole program, or the upgrade again?

  original title: iMac pc

  How to replace hardware or lost, broken, or missing Microsoft software:
  http://support.Microsoft.com/kb/326246/en-GB

• Accidentally, I installed a trial version 30 days of Windows and I want to uninstall it. How to uninstall a trial version? So, I want to install Windows 7 in its place.

  I tried to install a previous version of XP and it would not be installed, then a trial 30 days Windows version came.  Now I want to uninstall it so I can load Windows 7 hard disk.

  Hello, Steve Rath

  You don't need to uninstall the copy of XP

  Just install Windows 7 and do not forget to format the drive during installation.

  You will lose also all the other data on this drive.

  .

• Unable to load Windows XP? Help!

  I am trying to load Windows XP on my laptop Compaq A900.  On the screen that list partitioned and existing space on this computer, it says 'Unknown disc ' there is no nothing if I say I want to create a partition and if I hit enter says a problem has been detected and windows has shut down to prevent damage to your computer.  Is the error code comes up with is 0x0000008E.  I tried several times and it keeps coming back.  Help, please! Thank you

  I don't know where you see it. Most laptops come with a picture of factory restore on a special partition on the hard drive. The factory restore process is normally called by pressing a key of function (such as F11) to start the computer. There will be a message as to what function key press the screen when you start your computer. You can also consult the manual of your computer or the computer mftr.'s site, or contact technical support to learn how to restore your computer if you plant from each computer mftr. He does it differently - sometimes even between models.

  These machines also generally have a utility to create physical recovery disks in case the hard drive needs to be replaced or the factory restore image is somewhat damaged. If you have not created the recovery image recovery physical and/or damaged disks, contact technical support of computer mftr. to order a set of recovery disks. It is normally very expensive, around $20-25.

  Looks like you are trying to do the recovery or the Windows installation and that won't work.
  MS - MVP - Elephant Boy computers - don't panic!

• Cannot load Windows Live Photo Gallery

  Original title: Windows Live Photo Gallery

  I am only able to load Windows Photo Gallery, not the Windows LIVE Photo Gallery I want. I have Windows Vista.

  Hi hobiesailor,

  1. have you installed Windows Live Photo Gallery?

  If you have installed Windows Live Photo Gallery, and then you get any error when you start?

  If you have not installed Windows Live Photo Gallery, then we recommend that you download and install Windows Live Photo Gallery to access, or provide us with more details on the issue, so that we can help you better.

  See looking for Windows Photo Gallery?

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Desktop Pavilion p6-2011 pc: want to remove windows 7 install xp pro. How can I do this?

  Just picked up the machine above for my wife and want to remove Windows 7 install XP pro.  The machine does not allow me to do.  All the options in addition to removing the disc?

  Thank you

  Hello:

  You can install XP on your PC. You will need to install the drivers from the website of the manufacturer of each material.

  Lighter is right in the fact that HP will not support your PC under XP, so if you have problems operating system, don't bother calling HP support.  I guess that the material would still be under warranty.

  That being said... I guess that when you install the XP disc that it loads up, and when he says 'Setup starts Windows', he goes kerflooey, right?

  Well, it's because you need to load the SATA ACHI drivers for your machine when you receive this message at the bottom of the XP installation (press F6 if you need to load a SATA/RAID controller).

  So what you need to do, is go to your security & system menu in the Control Panel, click on Device Manager in Windows 7. Click on the small arrow next to the line of IDE ATA/ATAPI controllers.  Post back with the name of your listed drive controller.

  We will need to charge the correct SATA driver at the F6 prompt. You also need a USB floppy drive or a USB flash drive using the DCIS drivers copied on it, I will provide you with once you offer this info.

  You will also need to go into your BIOS and look in your storage options menu. See if there are parameters for the emulation of SATA mode. There should be 3 settings, ACHI, RAID and IDE.

  If there is an IDE framework, you can change your settings to that and load XP without going through all the stuff of F6, but you will then need to load this driver after installing XP for optimum performance of the road.

  Then I will provide you with the instructions to load the SATA ACHI driver if you can change your settings for the IDE BIOS.

  I'll give you also with the links (I hope) for many other drivers you will miss.

  I agree with also lighter it is imperative that you create these recovery disks before continuing with the installation of Windows XP.

  I'm pretty confident that you can get everything to work on XP.

  Paul

• Loading Windows 7 on new hard drive

  Hi everyone, I have a Toshiba laptop comes with windows 8.  I had to put a new hard drive in it and want to install windows 7 on it.  I have a new installation for windows 7 ult oem that has never been used.  It starts to load windows files and past on the screen "Starting Windows" and after about 3 seconds freezes and stops.  Anyone has an idea about what is up... do I have a bad drive oem?

  Please help, thanks

  John

  If it came with Windows 8, there probably secure boot enabled in the BIOS. Try disabling Secure Boot first, and then try reinstalling.

  https://APS2.toshiba-tro.de/KB0/TSB2B03F30002R01.htm