HP2311X LED monitor - no signal message

Similar Questions

• Apple Watch heart rate monitor, the signal can be shared with other devices such as the Garmin Edge 520?

  Apple Watch heart rate monitor, the signal can be shared with other devices such as the Garmin Edge 520?

  Hello

  No, that it is not currently possible.

• New HP 2011 x 20 '' LED monitor for old Dell Dimension 2400. necessary graphics card?

  My in-laws have an old Dell Dimension 2400 and the monitor exploded. I bought a new HP 2011 x 20 '' LED monitor. My WIRE went to set up, and he tells her that a HMDI graphics card is required.

  This is a pretty old computer. I think he might have as... 512 MB of RAM. Is there an inexpensive graphics card that will meet their needs?

  And besides, when they buy the graphics card, are there all the cables that they must reach a new monitor to an old computer?

  Thank you very much!

  Nice description of Dell:
  Video connector to 15 holes :-)
  
  Seems to be a VGA connector.
  
  From the description of the monitor:
  http://support.HP.com/us-en/document/c02643130
  There is an also vga connector, so you will have no problem to connect the two.
  
  No additional card is necessary, no other cable - just use the old vga cable.
  
  Your only problem might be the resolution:
  resolution 1600 x 900 set at the factory for the monitor.
  
  I don't know if you can set the resolution to Dell, you should test.
  
  Otherwise a 4:3 normal/old monitor would be better than this 'big screen' new.
  
  HTH
  C.
  
  P.S. the Dell printer documentation:
  http://support.Dell.com/support/eDOCS/systems/dim2400/

• How to connect two Dell UltraSharp U2414H 24 inch screen LED monitors daisy chain?

  I just bought two Dell UltraSharp U2414H 24 inch screen LED monitors, but it is unclear how two monitors must be linked together. Cable does not seem to be provided? Can anyone help?

  You have the L412Z XPS 14Z. It has the following video ports back =.
  CDM (Mini DisplayPort)
  HDMI

  XPS 14Z L412Z CDM on--> Dell mDP to DP cable--> #1 U2414H DP in
  XPS 14Z L412Z out HDMI--> HDMI to HDMI Cable--> HDMI U2414H #2 in

• SONY BRAVIA 50 "no signal message for find analog channels

  I bougth a BRAVIA 50 "and everything has worked perfectly, but suddenly the TV sent no signal message can not find the signal of channel or something like that. I bougth TV on December 2012 and this 4 last January that happened. What?, because I could see 7 channels before that. I tried to reset the original settings and I read, but nothing seems to work for some tips. The other features work well. It's just the analog channels. I hope someone knows the solution. Thank you

  I bougth a BRAVIA 50 "and everything has worked perfectly, but suddenly the TV sent no signal message can not find the signal of channel or something like that. I bougth TV on December 2012 and this February 4 this year that happened. What?, because I could see 7 channels before that. I tried to reset the original settings and I read, but nothing seems to work for some tips. The other features work well. It's just the analog channels. I hope someone knows the solution. Thank you

• The speakers affect LED monitors?

  I came across this question recently and experts views on this one. Pregnant really affect LED monitors in any way?

  No they are not. CRT monitors classic shot of the beams of electrons on points of phosphorus on the back of the glass which makes them shine to produce light that you see. The intensity of the beam defined the brightness and the chemicals in the phosphorus set the color.

  However, the beam is just a fine tip and on its own would just produce a single point on the screen. The beam sweeps across of the rotation of the screen in and out as needed because of two magnetic coils on each side of the screen and the scan moves vertically because of another pair of magnetic coils up and down.

  A magnet not shielded near a CRT would add its domain to the screen scanning coils and distort the beams leading to the beam lack his target and corrupt display. If left in the position the field eventually magnetize the chassis and leave a permanent deformation. All the speakers voice coil work essentially the same way and that's why the speakers sold for the use of the computer were always described as "blind".

  LCD screens do not use any magnetic principle to create the image so don't suffer not the effect of an external field. Older LCD use the cold cathode lamps to provide the backlight and in theory a very powerful magnetic field can distort the plasma in the tube so could cause some shading while the field is present but the residual magnetism is very small in comparison, so there is no permanent effects. Backlight LED don't even have this problem. A strong field that oscillates very fast can cause a problem, but it would not apply to a magnet.

  A mistake often made is the assumption that flat screens do not suffer "burn in" often seen on CRT screens. This is not the case, if the same image is displayed for a long period he set crystals partially at all times and produce a shadow on the screen. This happens so fast on LCD screens, but it can happen. (Big flat screen TVs) plasma screens have a sensitivity to burn in somewhere between the two.

• I mess with the display option (win + p), monitor losing signal, cannot bring him back.

  At first, I have a monitor, I tried something and end by pressing win + p and change the mode of display for projector only, losing the signal on my screen and can't put back T_T.

  Try win + P several times, it does not work. (A DVI connect to display the map - work).

  Then I stop, reboot, no signal is returned.

  Then I have connected 2 monitors and signal is back, I can change all fashion perfectly. (1 DVI + 1 D - sub - work)

  But, when I remove another monitor signal back to the first step. No signal to monitor. (1 DVI works again - not)

  So now I have to connect Monitor 2 (even if I don't use it) and there is signal monitor, if I remove one, I lose everything.

  Do you have any idea how to fix this annoying problem?

  Fixed it, by removing the cable, put the cable, remove the other insert this one delete and in about 50 times and windows blend and fix it for me * _ *;

• Black glitter and LED monitor S2440L screen

  I have a new LED monitor from Dell which flickers to a black screen during market for a few seconds and then turns back on. I can't understand why this happens. It happened when my monitor has been connected to the slot built in HDMI on my motherboard. And it always happens when I connect the monitor to the HDMI slot on my new NVIDIA GeForce GT 630 of ASUS graphics card that I bought recently. My motherboard is the ASUS P8Z68 - VLX running Windows 7 with an Intel i5 processor. DELL LED monitor is S2440L. Anyone experience this state of the black screen that comes at random on the time where to watch movies or even surf the net.

  Hello

  I have the same problem as you with my L-2440. The screen flickers and sometimes it's curtains blackout for a few seconds. I think this problem for this monitor is not an isolated case, because many people complained the same problem.

  I have noticed before I installed driver Dell and Dell monitors management program, this problem does not exist. Admittedly, I don't use 1 hour after the introduction if theres no way to be sure about that. Anyway I uninstalled both and use the driver default Windows (generic PnP monitor) and disable DDC/DCI under 'Other settings' in the configuration, monitor and now dancing lines are for the most part disappeared (sometimes but rarely sound still there), but black still happen.

  After experience, it turns out that it is related to electrical installation of the dwelling. Whenever someone support some switch in my house (On or Off), the screen will be black without fault. Im sure this model in particular have some bad Earth or something since I have never experience such problem in previous Dell monitor that I own or any other device. Try it yourself and make people put the switch in your home.

  I am awaiting response to Dell too because it is the time of 2md my monitor is replaced (totally busted S2320L and cannot be turned on) and Dell replaced by 2440L as the third replacement. Anyway Im afraid it will break the monitor sooner or later and I'm inclined to return it...

• I'm running a gateway DX4300 while running the monitor loses signal, etc...

  I'm running a gateway DX4300 while running the monitor loses signal, switch / stop out no computer and computer will not respond unless you unplug the wall.  When you plug the computer into the fans turn on automatically but the computer will not start.

  Hi shermanproffitt,

  Check if the physical connections are connected correctly.

  Try the steps from the following links:

  Frequently asked Questions
  http://support.gateway.com/s/monitor/7005481/7005481faq2.shtml

  Desktop computer - no POST / no video
  http://support.gateway.com/s/checklists/BPC/ck2007050376.shtml

• HP Pavilion 22xw 21.5 inch IPS: HP Pavilion 22xw 21.5 "IPS LED backlit monitor products: error message driver J7Y67AA #ABA

  I got a message from my assistant HP that there are two updates that need to be downloaded. The first was for AMD GFX Driver UMA Win10 64-bit YANICK
  
  I downloaded and installed, but now when I go into the settings, it is said "Screen backlight HP Pavilion driver error 22xw"

  However, my monitor seems to work very well? Don't know what to do with this message
  
  Thank you for any input!
  Susan untechie computer user

  Thank you very much for your answer, I'll put this link!
  However, that night that my computer has made an update of windows 10 and apparently solved the problem, this error message has disappeared... Now, that's service, lol.

• No Signal message when the monitor is connected to the graphics card.

  Thus, after posting this problem on different forums, I was told that my power (300w) was too low for my Radeon HD 7570 I tried to install. After you install a 585w power supply, the problem is still happening.

  Model: HP Pavilion h8 - 1240 t

  OS: Windows 7 64-bit

  Error: Monitor says "no signal" when connected in the PCI slot where is the graphics card.

  Changes: this always happened, did not get a single card to run this stupid computer!

   

  The DVI cable is completely plugged the monitor into the PCI slot and the graphics card is fully in. The fans on the graphics cards spin but it is not detected at all. It does not appear in Device Manager.

  Data sheet:

  I7-2600 3.4GHz

  8 GB RAM

  Orion 585w PSU

  Radeon HD 7570 (it didn't come with the computer, otherwise it would work...)

  PEGATRON CORPORATION 2AD5 1.03 (I guess that's the motherboard)

  No. I went to Dell and downloaded THE drivers that ACTUALLY work. Computer restarted and everything works fine.

• computer does not start until montor no video signal message

  Dvd player unpluging and pluging into computer slave dvd powered down, that I went back to the orignial dvb car, won't boot upward and montor reads no video signal.

  The computer feeds also on orange with led op. running xp SP3

  Hi rdb 1949,.

  • Are you facing the question after you have connected the DVD player to the computer?

  This error message occurs generally if the faulty monitor or video card in the computer driver is damaged.

  I suggest that you start the computer to activate the VGA Mode or mode safe mode and check if the computer starts very well.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Also, connect another monitor to the computer and check if it works.

• No Signal Message

  I have this type of screen, below, that I have linked to a Directv receiver with an HDMI cable.  I have the settings on HDMI.  I can't look at a pay-per-view HD movies, but I can see everything in HD.  Initially I thought that the problem was that I was trying to watch channels that I don't subscribe to the, but last night I tried to watch a HD PPV movie and received the message no Signal and the screen goes black.  I have to unplug the whole system from the wall and plug it in again to get the picture to come back.  I tried to change the resolution settings, mine goes to 1080i, and I can't understand what is wrong.  I have sent Directv, but have not yet heard anything.  Any suggestions?  Thank you.

  Model: HP2210
  S/N: CNT018F1TM
  Other numbers of the monitor: WB988A and HSTND-2571-T

  Through a few other questions, I discovered that I need to untick the box 1080 p on the receiver Setup menu.  I did it and it worked.  Thanks for your help!

• Recently, to make 'No Signal' message, after the new router

  I have a new Verizon Fios router, and since then my Apple TV does not work.  The TV keeps giving me the message "No Signal".  This could be a coincidence, and I really need a new HDMI cable?

  It is unlikely to be something to do with the router, but exactly the type of question that you get with a poor HDMI cable.

• his IPS LED backlit screen 27vc: could not find a way to mount 27vc 27 "IPS LED monitor

  I recently bought the 27 "and 22" HP vc IPS LED backlit monitors. My intention was to mount them on a mount for two monitors that clips to the back of my desk or on the wall. Every company in the world sells the same media/materials for double monitors, but all have the traditional media that has 4 screw holes. Vc monitors do not have the ability to accept this type of Mount. I tried to call HP customer service and am redirected more than 5 times to the representatives who had no idea how mount it and didn't have an adapter. It is impossible that it is impossible to mount these monitors. Anyone know of a replacement product or an adapter that I can use to ride together?

  Hello

  HP has monitors with standard VESA mounting holes. My suggestion: take it to the shop and swap for the one that supports standard VESA otherwise must a good skill and a good drill.

  Kind regards.