HPT930: Questions of conspiracy with print landscape

Similar Questions

• Problem with printing of pdf documents: landscape instead of portrait

  When I try to print a pdf file or a map of bing, my all-in-one HP officejet (J6480) started printing landscape although the portrait is selected.  I use Adobe Reader X, Office 2010 and IE 2012 (64-bit), Windows 7 (64-bit).

  Hello

  What application you use to set the properties?

  Perform the steps suggested by Danielle_a of the binding and the audit.

  http://forums.Adobe.com/thread/303014

  Hope this information helps.

• OfficeJet 6500 printer ONLY print landscape

  Hi, I have an Officejet 6500 (E709n).  I also have Windows 7 64 bit.

  I did nothing yet suddenly the printer started printing in landscape, even though my settings call for the portrait.  It has a new pop of the print window. (First default window appears select print, then it coils, then jumps to the top of the final window which is the new.) The following image is what I'm talking about.  All my settings are correctly defined and yet it still prints as shown in the picture.

  Thanks in advance for any help!

  

  Hello MomToMVS
  
  After looking into your problem, a bit I found a thread on another forum with what appears to be exactly the same problem. Below I will include a link the the wire and instructions on what has been done to solve the problem. I would like to know if it works or not.
  Firefox default print landscape
  
  1. in the web in Firefox address bar type about: config and press ENTER. (it can warn you about changing settings here just click OK to continue)
  2. Locate the print.printer_NAME OF PRINTER.print_orientation (where the PRINTER NAME is the name of your printer) and right click on it and click Reset.
  3. conclusion of the tab, and try again (it may be a good idea to restart Firefox first).

• Connected HP OfficeJet Pro 8600 Plus status reads "problem with printer."

  I could just ePrint on an OfficeJet Pro 8600 Plus replacement and them have not used for printing yet. I was in the devices page to manage the settings and change an address for one of my devices. The newly added column 8600 State reads 'Online', but also 'problem with printer '. Instructions I was referring to the display panel of the unit for Outlook2003 on the given problem. A check of the display surface showed no information, just a typical home screen. I checked through the display print and found no problems-all functionality is enabled and fully functioning. I checked then the functions of printer in the window 'Printers and devices' of all computers (all running Windows 7 Professional) on the office network. The 8600 are active and full functionality works correctly between the printer and all the computers.

  I then close the printer 8600, left for several minutes, and then lit it back and reconnected. The State says 'Problem with printer' remains in the device window HP.

  I am at a loss as to what this supposed problem can be and don't know what should be a next step. Does anyone have any advice or information that could help in this situation? It would be appreciated. Thanks in advance to those who could help

  HP support responded to my question by e-mail. I was told that the message 'Problem with the printer' is due to a bug in their system. Also said that as long as the status column indicates the printer is "Online" and everything else is fnctioning correctly, don't worry about this.

  I consider that a resolution of the post!

• CP 2025dn: need help with printing double-sided 2025dn

  Got a new computer NUC and installed Win7.  Printer not duplex plus.  Downloaded last UPD. (May 2016).  Printer connected to the network.  Hooray, equivalent to the FX Toolbox but still no duplex obtained.  The printer configuration page ON Duplex.  When I try to print from an application (Quicken, TextPad, etc.) the only option duplex I get is manual.

  The Advanced section in the properties of the printer in different applications gives me the option to print on my butt (which might amuse the guys in the locker room) but does not allow duplex printing.

  Any ideas on how I can get double-sided printing back?  Move to Win8 or higher version is not an option.

  F_O

  On Windows systems, the function "automatic detection" used by some printer drivers on the install (or update) does not always; make sure the driver knows that a duplex unit is present on the printer (assuming that a single is present):

  • For the instance of the printer in question, bring up the printer properties dialogue.
  • Select the device settings tab.
  • Make sure the duplex unit is set to installed and not installed.

  You will probably need to be logged in with administrator credentials in order to change the settings of the device.

  If your model does not have a duplex unit equipped, so you can't do automatic duplexing; You can do manual duplex printing (assuming that the printer driver supports this).

• What is the number of spare parts of the neck strap that comes with ILCA - 77M 2 (with printed logo a77II)?

  What is the number of spare parts of the neck strap that comes with ILCA - 77M 2 (with printed logo a77II)?

  Kind regards

  Michael

  Hi cmosse,

  Welcome to the community of Sony!
  Good day and thanks for the comment. The part number for the neck strap is 4 - 535-925-01.

  For further assistance about your concern, please contact us recommended to visit our Sony Global Web site for more information on contacting the Sony's Support centre in your area to http://www.sony.net/SonyInfo/Support/.

  If my post answered your question, please mark it as "accept as a Solution.

  Kind regards
  Zander

• compatibility with print shop deluxe version 21

  is Vista compatible with Print Shop Deluxe Version 21?

  Switch which autour...

  It should be "V21 PrintShop Deluxe' which is or is not compatible with"Windows Vista".  After all - "Windows Vista", probably has use beyond "PrintShop Deluxe v21" running and does not install other software (is the operating system.)

  You would ask those who make the software in question.  I remember having said something similar on this software very recently...  Something about v22 works on Vista but not Windows 7.
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_programs/why-wont-the-printshop-20-professional-load-in/d7ec4f68-84ff-41dB-895F-01c46482a37c

  If you already have and it will install/work - there is your answer.

  If you plan to buy - why not get the latest version you know works and are still supported?

• Impossible to combine printing without margins with print on both

  Using the HP 8100 x, I am unable to print on both sides (using Flip on long edge) and printing without margins.

  On the first page impression without margin does not work well. It covers the whole page. There is a white bar on the left to the bottem of the page.

  It is impossible to use printing without margins in combination with printing (automatically) on both sides?

  Hello

  To print duplex automatically the printer need the edges to put the papers autour is why we cannot print double-sided and without borders. In fact printer wll notifying/warning you: he can do and it resets automatically. If you want to print borderles for sides of bot, just printing one side (one page) and then put the paper in the tray to print, and then on the other side using TWO print jobs.

  Hope that answers your question.

• Who driver @PJL JOB printer NAME of HP with print data?

  Hello

  I need to extract the name of the job to print raw data received on port 9100 (document name).

  In PJL job name is transferred with the FIXED JOB NAME = "document" @PJL - command.

  My question is what HP printer driver generates these PJL data? I discovered that my Laserjet M1530 private pilot does, but I have found no other.

  Anyone know who the build of windows in the HP printer driver produces the JOBNAME-PJL output?

  Thx a lot

  Thomas

  Perhaps the built-in PCL6 (PCL XL) drivers do not understand what you want.

  My Windows 8.1 Professional 64-bit system has a PCL5 driver for LaserJet 1320 printers:

  

  You may need to click the Windows Update button in the Add Printer dialog, then wait (possibly several minutes) while additional drivers are downloaded, until the list is filled again.

• HP Envy 4504: Envy 4504 photo prints too red with print quality = better

  Hello

  I hope someone can help.

  On my HP Envy 4504 photos are printed OK print normal quality, but when the print quality is set to best photos are printed to the red. In addition, with DPI Maximum printing photos are much too red.

  This takes place two times printed on paper Normal and on Photo paper

  With the GIMP, I tried to make an example of how a photoprint looks like.

  I made the example by changing the color Balance: Red cyan - about + 40:

  (my GIMP is Dutch...)

  

  Here is the result:

  LEFT: Photo printed in normal quality; Photo on the RIGHT printed in better quality:

  

  I have already completely remove the software HP Envy and did a clean reinstall. No change.

  I have print-head - cleaning cycles (2 times); color of HP-testprint strips looks very good: all are strong in alignment is correct

  Unfortunately: No picture change in best quality still too red.

  The ink levels are okay.

  Any suggestions what is wrong and what can solve this problem?

  Thank you for your support

  Kees-Jan Timmer

  Hi @Kees-Jan,.

  Welcome to the HP Forums!

  I noticed that your HP Envy 4504 prints photo is too red with print quality = best on Windows 10 operating system. I'm happy to help you!

  Where a setting is disabled, with GIMP, have you tried to print photo quality with other programs? If so, what happened?

  You use genuine HP cartridges or refills?

  None of your ink cartridges are low or empty?

  In the meantime, please make sure that all the steps in this guide, fixing poor print quality are executed. And let me know what happens!

  Thanks for posting and hope to hear from you soon!

  If this, or one of the posts on this thread, helped you to solve the problem, please click 'Accept as Solution' said post. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

• My lexmark wireless printer seems to not work whenever I run paper he says not comm.with printer

  I have a lexmark wireless printer that seems not to work whenever I run paper, its says not comm with printer

  Hi chinny111,

  ·         If it works well before?

  ·         Did you change?

  ·         What is the operating system installed on the computer?

  You can see the following Lexmark article and check if it helps.

  "Communication not available" or "Document Failed to Print" Error Message and the print job hangs in the print queue

  Respond with more information so we can help you best.

• After the installation of Vista update, receive the error code 21 with printer software

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas

  Download update for 32-bit Vista because brother MFC3220C box to restart the printer says cannot start error box App Installer says error code ['C:\USA\Install\3220C\Inst32.exe'] 21. I added Vista Ultimate 32 bit. I went to the brother site and talked to technicians and as usual runaround says I need to update with the new printer (Yes, well, well, if I do it will of course not brother!)

  * original title - printing with printer Brother MFC3220C problem. When I install the update to run 32-bit Vista; I get to the part of the installation where I plug the USB cable and the printer software will block upward. I get a code on the reboot error code ['C:\USA\Install\3220C\Inst32.exe'] 21 *.

  John Walker

  You must get your drivers for your Brother printer if possible from the manufacturer.

  Anything here useful?

  http://welcome.solutions.brother.com/BSC/public/as/au/en/DLF/download_index.html?reg=as&c=au&lang=en&prod=mfc3220c_as&dlid=&flang=English&OS=74&type2=-1

  There is also a uninstall tool mentioned that you can use to reinstall through Windows plug-and-play.

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• How, please, directory of files to print, or doing screen print or transfer to Excel so I can leave with print?

  How, please, directory of files to print, or doing screen print or transfer to Excel so I can leave with print? Windows XP

  There are various ways to accomplish this, but the easier no doubt is to use the (free) Karen's directory printer .

• HP Color LaserJet MFP M277 Pro: Problem in black with print on the right side of the paper on a HP Color LaserJet Pro M277dw MFP

  When I print a page of text or an image to be in color or black and white about 1.5 inches on the right side of the page, the black part is dimmed.  I tried to shake the black toner, but nothing has changed...  Should I replace the black toner?

  Hey @candreas,

  Welcome to the Forums of HP Support!

  I see that you have some problems with printing faded on the side of your impressions of your printer Laserjet M277dw range. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once completed, this document describes How to solve print quality problems with your printer.

  If after following the above, are you always see fainted to prints, either the cartridge or the printer needs to be replaced. You can contact the HP Support by clicking here and filling out the form below.

  Please let me know the results after following the above. If you are able to improve the print quality or to reach a resolution with the support, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• LaserJet P1102: do not print landscape

  It is surely not normal... I just said my new P1102 cannot print landscape.

  I have not heard this kind of thing being said since about 1987 Symphony finally worked out how to print spreadsheets in format landscape.

  Surely this is not right?

  Can peope really even printers that can't print landscape?

  My problem is this, my old HP printer died recently, so I bought this new, the P1102. Worked great until I tried to print the Excel calendar in the landscape. Just wouldn't do, just do print portrait regardless of what I tried to change the settings.

  Try printing landscape in other software too, but only ever printed portrait.

  Can someone either help me solve this oooooor (gulp...) confirm that this new printer can not print landscape.

  I am astounded that there are always done printers that can't print landscape... say it isn't so... Please...

  Incredible... I answer to my own problem of forum here as Support HP were unable to help me.

  My original problem was that I couldn't print any form on my new Laserjet P1102 landscape software.

  I called and they told me that P1102 'n' print landscape.

  I was stunned.

  Then the guy said that he was jumping on my computer to see if there was anything he could do, he did, and then confirmed my printer CANNOT print landscape.

  Confused I checked then a colleague who also has a P1102 (where my purchase) who say that he has no problem printing landscape at all.

  What the...

  I then noticed something... in my list of printers and devices, the new P1102 was referenced as follows:-

  XPS HP Professional Laserjet P1102...

  What is XPS......? ! My colleagues didn't say that.

  So I uninstalled the printer and re-installed. Now works fine and prints landscape most certainly!

  No idea what is XPS or why he was there, I do not, my printer now works fine, but HOW ON EARTH, a HP technical support guys can say this printer does not print landscape is beyond me. Easy to miss the XPS thing perhaps, but I can't imagine there was a printer cannot print landscape for 30 years so why he said that I have no idea.

  Thus, no faith in the team of support here, I'm afraid. Google has more help.

  E - less for HP, see the teacher!