I am unable to get ios mobile to connect to the Office Server, what can I do?

Similar Questions

• I have Adobe Reader DC, but have just started to give a message that Adobe is unable to connect to the DDE server, what can I do?

  I have Adobe Reader DC, but have just started to give a message that Adobe is unable to connect to the DDE server, what can I do?

  Hi johnf49911817,

  * Try the solutions below: -.

  Solution 1) (this error occurs when you have more than 1 process of Acrobat running)

  (1) go to the task by pressing Ctrl + Alt + Del Manager

  (2) go to the process in the Task Manager

  (3) terminate all processes associated with Acrobat

  (4) start Acrobat again.

  Solution 2) open Acrobat access to menu help & repair installation.

  Solution 3) control the association of file on your system.

  Solution 4) course for HKEY_CLASSES_ROOT\acrobat\shell\open\ddeexec\application and replace the key 'AcroviewA11' 'AcroviewR11.

  Kind regards

  Christian

• Client DHCP is unable to get a valid IP address from the DHCP server.

  Client DHCP is unable to get a valid IP address from the DHCP server. I have a home edition of Windows XP attempts to connect to my router wirelessly with wireless or wired connection but I get an error in Event Viewer with the discription DHCP 1007 error message. From what I researched, I discovered that the DHCP service depends on the AFD, TCP/IP and NetBT services. All these services are correctly place and worked very well (even the DHCP service is running without error) but every time I try to release/renew my IP address I receive than DHCP warning in the case where the viewer and I just cannot get a valid IP address of the server (router) I also have one of these verizon wireless G3 usb adapters and it works fine. I also have a good ping back when I try to do a ping localhost (for the closure) I also tried the preinstallation of uninstalled drivers from the adapter/s and nothing works. The only entrees in the registry for DHCP error are also AFD, NetBT and TCP/IP nothing else there, also all the files in the/system32/drivers afd.sys netbt.sys and tcpip.sys in addition to solve the problem, I'll mention that I installed and reinstalled Northon earlier, I do not remember if the problem appears before or after that. I receive also any error or warning in the security log or at least I don't know how to read: P

  Thanks in advance

  Thanks for the information.

  I hope you know that it is risky to connect the laptop to the Internet with no firewall and no antivirus... If this laptop is already connected to the Internet in this State, he is perhaps already infected.

  You said you know the router works because the other computers can connect successfully to it.  You should check the configuration of the router to make sure that it is not configured to limit the number of IP address it supplies, and (b) it is not configured to filter users by MAC address.

  When this laptop is connected by Ethernet, even if he gets the IP address of 169.254.x.y, can you ping the router?  Find the IP address of the router on any computer connected to it by running the ipconfig command in a command prompt window.  The "default gateway" is the IP address of the router.  Run the ping command in the command prompt window as well.

  If the ping is successful, it is possible that you might be able to use an IP address in the correct range for an Ethernet cable (but I doubt that it works for the wireless).

  It is very difficult to cite anything in this forum.  If you click on the link "Reply citing", all of the message to which you are replying is quoted.  You can copy the citation and delete parts of it, but it is not very user friendly.

• I have a printer HP photosmart premium c309gm - I'm unable to scan documents on my computer to the printer. What can I do to implement that?

  I have a HP Photosart/c309gm premium wireless printer.  I'm unable to scan a document to the printer on my computer.  What can I do to implement that?  It's not a problem with printing from my computer, I just can't access the scanning functions.

  Nothing to do with the office or to win

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02251801&CC=UK&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=#N6409

• I'm trying to update my phone.  The only list update is iOS 9.2.1.  When I try to update, it tells me that I can't because I am not connected to the internet.  How can get the update on my phone.

  I'm trying to update my phone.  The only available update is iOS 9.2.1.  When I try to upgrade, it tells me that I can't upgrade because I am is no longer connected to the internet.  How can I upgrade my phone?

  Connect to the internet.

• I can't connect to internet, I get a message "can not connect to the proxy server. My firefox does not connect, I can connect through aol.

  Unable to connect to the internet through firefox, can connect through aol, firefox was conneting before, now I get "cannot connect to the proxy setting.

  • Press F10, or press the Alt key to bring up the 'Menu Bar' temporarily if the menu bar is hidden.
  • Use "Firefox > Options" instead of "tools > Options" If the menu bar is hidden.

• I can not get the automatic updates on my samsung jack sgh-i616. _ "connection to the update server is not available. Check your data connection settings and make sure that the device date and time are correct "___RESULT CODE: 80072ee7__ _"

  I can't get the automatic updates on my samsung jack sgh-i616.

   

  "Connection to the update server is not available. "Check your data connection settings and make sure that the device date and time are correct.

   

  RESULT CODE: 80072ee7

   

  -It is a windows mobile 6.1
  
  
  Thank you very much! = D

  As a guide.

  This error code translates ERROR_INTERNET_CANNOT_CONNECT.

  You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• Outlook Express: Unable to connect to the mail server! (error 0x800CCC90)

  original title: Outlook Express: unable to connect to the mail server!

  Im trying to get my outlook express to receive and send messages from my live.com account but it comes back with: the server responded with an error. Account: "Live.com', Protocol: POP3, server response:'-ERR AVG POP3 Proxy Server: cannot connect to the mail server!', Port: 110, secure (SSL): no, Server error: 0x800CCC90, error number: 0x800CCC90."

  Someone knows how to fix this? I tried to remove and add the account again using IMAP instead of POP3, but still get an error message, the e-mail address and the password are all correct and I think that ive got the right to Server (live.com?) Im not exactly computer so any help would be greatly appreciated.

  You will find the right settings for an account on this page live.com: send and receive Hotmail from an e-mail application. To change your settings, select Tools > accounts > {account} > properties and make right onto the tabs of servers and Advanced entries.

  [I moved your question on the forum just for Outlook Express issues.] You should not notice a difference].

  Noel

• Error code: 800ccc0e and the message "Unable to connect to the host server", when you set up Windows Mail to receive discussion group messages.

  I recently signed up for Windows Mail, Windows Vista Help. I have configured my Gmail OK account, but when I click TOOLS then Newsgroups I get the following error: unable to connect to the host server. When I click on show details, he said: Microsoft Community Server: msnews.microsoft.com Protocol: NNTP Port: 119 secure (SSL): 0 Code: 800ccc0e

  msnews. Microsoft.com has not existed for about three years now. MS close their news servers. You can still access newsgroups, but you will have to do with one another as eternal September or AIOE news server.
   
   

• SPA-3102: unable to connect to the SIP server

  Hello

  We have a SPA-3102 installed and work properly in our US Office. We are trying to install another one in our office in India, but we cannot get this device to register with the SIP server.

  This device works perfectly when try us two different residences here in India with two different providers. But when we try to our office with a third party service provider, it is impossible to save.

  The internet connection at the office from the East through an ADSL router which is mode bridged with two IP static coming out of it. We are able to have access to the internet for our PC through this SPA-3102, but the SPA itself is unable to register with our SIP server. We use a Gizmo5 SIP server.

  The same parameters were working in our offices in the United States and two different residences in India but does not work in our office. I don't think that the ISP here has nothing to do with this problem. Would be - this works the ADSL router in bridge mode? Can I make changes in the settings of the SPA to work around this problem?

  Any help is appreciated.

  The problem could be the firewall or the router, but it is also possible that your Indian ISP is blocking voip connections.  It was reported that is not unknown in India.  Sometimes this type of blocking is done by throwing packages for voip standard sip signalling port 5060. You can easily change the SIP port in the SPA3102 to traffic returning to the SPA packages and in fact routers often changes the port without your knowledge, but packets destined for voip provider must use the port specified by the provider number.  Since you can access the internet with your pc, I would try to run tests to see if this is the case.

  I ran a few ping tests and tests to see if I could save with other providers or services that use replacing or other sip signaling ports.

• My Sprint HTC Android mobile phone connects with the supplied USB cable, but the computer says 'No HTC Device Connected'

  My Sprint HTC Android mobile phone connects with the USB cable, but the computer says 'No. HTC Device Connected' so I can't sync...

  Hello

  1. do you have HTC Manager installed on the computer?

  2. have you tried it with different USB ports?

  You need the HTC Sync HTC phone Manager software.

  Method 1: Try again with different USB ports and see if that helps.

   

  Method 2: If HTC Sync is installed, if you get the message "no device connected" in HTC Sync, ensure that your phone USB setting is changed to "Charge Only" to "HTC Sync".

  If the methods above do not help, you can contact HTC for additional help.

  Here is the link: http://www.htc.com/us/support/

• I have a Dell Windows 7 after downloading updates crucial sercurity, I get a message saying "Connection to the internet." The display then returns to the logo screen. What can I do?

  I have a Dell Windows 7 after downloading the critical updates, I get a message saying "Unable to connect to the internet."  What should I do?

  Hello

  1. Once you get this error message?
  2. are you able to browse the internet using your internet browser?

  Step A.
  Please check if you are facing the same question when working in mode safe mode with networking.
  a. restart your computer.
  b. when the computer starts, you will see your computer hardware are listed. When you see this information tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows 7 Advanced Startup Options.
  c. using the arrow keys, select the desired option of Mode without failure.
  d. press the Enter key on your keyboard to boot mode safe mode of Windows 7 with networking.
  e. when Windows starts, use check and Internet explore if the problem persists.
  For more information, refer to the article below.
  Troubleshooting in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshooting-problems-while-in-safe-mode

  Step B.
  If the problem exists not in Mode safe run mode startup minimum troubleshooting to find the root cause of the problem.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

  I hope this helps.

• Unable to connect to the game server

  whenever I try to play canasta lately I get up error message "Unable to connect to the game server" whas?

  Could be a problem with the security software, try to turn it off and check if that helps and if not contact the game provider

• Windows Media Center - not the initial download put in place data for guide "unable to connect to the remote server.

  Hello

  Looking for help on this one...

  I have a new install of windows 7 pro running, and I was not able to get the guide to download Windows Media Center.   I am up-to-date with all the updates and SP1 version running.   My video card drivers are also updated.

  I use HDHOMERUN PRIME equipment with cablecard and who receives a TV signal very well and I am able to view it in WMC.    I use Verizon FIOS and my zip code is 07452.    Before this computer, I ran the cablecard even with a ceton infinitv and had no problem Guide at all.

  It's just that I can't download the guide data.  Its just totally blank.   I receive the channels and view them, but there is NO data.      Whenever I run the TV setup the same question comes up.  Cannot download the initial configuration data due to the error of previous download.   As far as I know, there is NO error message when Windows installed... actually... I reinstalled windows completely and this has not solved the problem.    I tried to manually download the guide which did not help.   It... nothing happened when I turned 'on' and 'off' WMC in Control Panel to reinstall.  I even tried explore the ehome folder and remove the file db... but nothing is helping.

  I can't find a file mcupdate.exe light on my system - don't know if this is relevant.   When I looked in the event viewer here are some of the error messages that I see.

  Impossible to extract the EpgLineups (error: unable to connect to the remote server)
  Impossible to extract the MCEClientUX (error: unable to connect to the remote server)

  I'm starting to think it's a matter of windows.   Anyone have any ideas?

  Mark

  E-mail address is removed from the privacy *.

  On Tuesday, September 23, 2014 00:32:35 + 0000, Mark_Sap_70 wrote:
   
  > I'm starting to think it's a matter of windows.   Anyone have any ideas?
   
  See this thread
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/is-the-Media-Center-Guide-download-service-down/f0a5ae10-00ea-4635-9177-12074fa7ee81?msgId=87f3f3b5-A485-4c41-8f35-43a4e2a75d7c
   
   
   
  __________________________________________________________________________________________________
  Barb
  MVP Windows Entertainment and connected home
  My Blog - http://digitalmediaphile.com/
   
  Please mark as answer if that answers your question
   
   
   

• Uninitialized encryption algorithm (91); Unable to connect to the LDAP server

  Hello

  I configured a new 'provider' in Weblogic to LDAP server. And restarted the management server.

  When I tried to search for LDAP users in the tab "Users and groups", there was no displayed to users. I checked the logs and found the entrance of error below.

  < SNIP >

  Caused by: netscape.ldap.LDAPException: encryption not initialized (91); Unable to connect to the LDAP server

  to weblogic.security.providers.authentication.LDAPAtnDelegate$ AtnLDAPSSLSocketFactory.makeSocket (LDAPAtnDelegate.java:4647)

  at netscape.ldap.LDAPConnSetupMgr.connectServer (unknown Source)

  at netscape.ldap.LDAPConnSetupMgr.openSerial (unknown Source)

  at netscape.ldap.LDAPConnSetupMgr.connect (unknown Source)

  at netscape.ldap.LDAPConnSetupMgr.openConnection (unknown Source)

  at netscape.ldap.LDAPConnThread.connect (unknown Source)

  at netscape.ldap.LDAPConnection.connect (unknown Source)

  at netscape.ldap.LDAPConnection.connect (unknown Source)

  at netscape.ldap.LDAPConnection.connect (unknown Source)

  to weblogic.security.providers.authentication.LDAPAtnDelegate$ LDAPFactory.newInstance (LDAPAtnDelegate.java:4141)

  at weblogic.security.utils.Pool.newInstance(Pool.java:37)

  at weblogic.security.utils.Pool.getInstance(Pool.java:33)

  at weblogic.security.providers.authentication.LDAPAtnDelegate.getConnection(LDAPAtnDelegate.java:3487)

  at weblogic.security.providers.authentication.LDAPAtnDelegate.getConnection(LDAPAtnDelegate.java:3479)

  at weblogic.security.providers.authentication.LDAPAtnDelegate.listUsers(LDAPAtnDelegate.java:2267)

  at weblogic.security.providers.authentication.LDAPAuthenticatorImpl.listUsers(LDAPAuthenticatorImpl.java:178)

  at weblogic.security.providers.authentication.ActiveDirectoryAuthenticatorMBeanImpl.listUsers(ActiveDirectoryAuthenticatorMBeanImpl.java:227)

  at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)

  at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)

  at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)

  at java.lang.reflect.Method.invoke(Method.java:597)

  < / SNIP >

  Can someone tell me why I get this error.

  Thank you

  Shakeel

  Hello

  Please add - Dweblogic.security.SSL.nojce = true in your startWeblogic.sh script in the section "JAVA_OPTIONS.

  Example: JAVA_OPTIONS = "${JAVA_OPTIONS}-Djavax.net.ssl.trustStore=/u07/oracle/certstore/test_keystore.jks-Dweblogic.security.SSL.nojce=true."

  Please try this.

  Thank you