I can't connect to the internet on this laptop wireless

Similar Questions

• I use windows XP service pack 3 and I can't connect to the internet on your laptop even if I can connect using my other devices.

  I have tried everything I can think of nothing doesn't. The strange thing is that it connects as usual and I can even use Skype and download updates, but I can't surf the net. I can't understand. I have tried ipconfig release and then renew, repairs of stack TCP/IP, Winsock reset and the use of different browsers. I ran the XP connection troubleshooting tool and received the following message, that this is probably caused by your firewall settings

  "check the settings of the firewall for the HTTP port (80), HTTPS (443) AND ftp PORT (21) port.

  The problem is that I can't change my firewall settings that I can not start the firewall and get this error message every time I try

  Cannot start the service Windows Firewall/Internet Connection Sharing (ICS) on the Local computer.
  Error 0 x 80004015: the class is configured to run as a different caller's security id

  I downloaded the hotfix from microsoft, but it made no difference unfortunately.

  I use AVG 2011 antivirus protection. I tried connecting via the wireless and wired. I did ipconfig and tried to rattle of my other devices and my router and everything seems normal because they can communicate with each other. See below.

  Microsoft Windows XP [Version 5.1.2600]

  Copyright (C) 1985-2001 Microsoft Corp.

  C:\Documents and Settings\Administrateur > ipconfig

  Windows IP configuration

  Ethernet wireless network connection card:

  The connection-specific DNS suffix. : gateway.2wire.net

  IP address...: 192.168.1.72

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. : 192.168.1.254

  C:\Documents and Settings\Administrateur > ping 127.0.0.1

  Ping 127.0.0.1 with 32 bytes of data:

  Reply from 127.0.0.1: bytes = 32 time<1ms ttl="">

  Reply from 127.0.0.1: bytes = 32 time<1ms ttl="">

  Reply from 127.0.0.1: bytes = 32 time<1ms ttl="">

  Reply from 127.0.0.1: bytes = 32 time<1ms ttl="">

  Ping statistics for 127.0.0.1:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 0ms, Maximum = 0ms, average = 0ms

  C:\Documents and Settings\Administrateur > ping 192.168.1.72

  Ping 192.168.1.72 with 32 bytes of data:

  Response to 192.168.1.72: bytes = 32 time<1ms ttl="">

  Response to 192.168.1.72: bytes = 32 time<1ms ttl="">

  Response to 192.168.1.72: bytes = 32 time<1ms ttl="">

  Response to 192.168.1.72: bytes = 32 time<1ms ttl="">

  Ping statistics for 192.168.1.72:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 0ms, Maximum = 0ms, average = 0ms

  C:\Documents and Settings\Administrateur > ping 192.168.1.254

  Ping 192.168.1.254 with 32 bytes of data:

  Request timed out.

  Response from 192.168.1.254: bytes = 32 time = 2ms TTL = 255

  Response from 192.168.1.254: bytes = 32 time = 4 ms TTL = 255

  Response from 192.168.1.254: bytes = 32 time = 1ms TTL = 255

  Ping statistics for 192.168.1.254:

  Packets: Sent = 4, received = 3, Lost = 1 (25% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 1ms, Maximum = 4ms, average = 2ms

  C:\Documents and Settings\Administrateur > ping 192.168.1.70

  192.168.1.70 ping with 32 bytes of data:

  Response of 192.168.1.70: bytes = 32 time = 2ms TTL = 128

  Response of 192.168.1.70: bytes = 32 time = 94ms TTL = 128

  Response of 192.168.1.70: bytes = 32 time = 8ms TTL = 128

  Response of 192.168.1.70: bytes = 32 time = 13th month TTL = 128

  Ping statistics for 192.168.1.70:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 2ms, Maximum = 94ms, average = 29ms

  C:\Documents and Settings\Administrateur > ping 192.168.1.254

  Ping 192.168.1.254 with 32 bytes of data:

  Response from 192.168.1.254: bytes = 32 time = 1ms TTL = 255

  Response from 192.168.1.254: bytes = 32 time = 2ms TTL = 255

  Response from 192.168.1.254: bytes = 32 time = 3ms TTL = 255

  Response from 192.168.1.254: bytes = 32 time = 3ms TTL = 255

  Ping statistics for 192.168.1.254:

  Packets: Sent = 4, received = 4, lost = 0 (0% loss),

  Time approximate round trip in milli-seconds:

  Minimum = 1ms, Maximum = 3ms, average = 2ms

  C:\Documents and Settings\Administrateur >

  I worked on it for 2 days straight trying to find a solution and this is my last resort. I really hope that someone can help me because I even tried technicians internet ATT who couldn't help me. There must be a solution out there. I must be missing something. It must be a software problem or something simple. Help!

  Hello

  You can check this link:

  http://support.Microsoft.com/kb/920074

  Note:

  It implies also on Windows XP SP3

• Vista PC is offline, unable to connect to the Internet by LAN or wireless.

  Original title: Vista (Japanese OS)

  My Vista pc is offline (unable to connect to the internet), how install and run the Fixit tool?

  I have read that the English, however, my pc is in Japanese. I can't connect to the Internet by LAN or wireless.
  How can I get the Fixit tool to work on the said pc?
  Help, please!

  Hello

  1. what Fixit tool you try to run?

  2. what exactly happens when you try to connect to the Internet? You receive messages or error codes?

  You can read the following article and check if it helps:

  Windows wireless and wired network connection problems

  You can also read the following article to change the display language:

  Change the display language

  You can use another computer to download the Fix from Microsoft, then use portable storage such as a USB drive, CD, DVD, etc., to carry the Microsoft fix it on your computer.

• I have the wireless option, but if I use it not I can't connect to the internet.

  I have the wireless option, but if I use it not I can't connect to the internet.

  original title: difficulty borrowed from internet

  If it's the Acer utility, it is best to visit Acer support:

  http://support.Acer.com/us/en/default.aspx

• I can't connect to the Internet wirelessly

  I just replaced my wireless device and now I can't connect to the Internet wirelessly

  Hi JimMahoney,

  You have installed the necessary drivers for your new wireless device?

  You receive an error message when you try to connect to the internet using your router?

  What virus protection software is installed on your computer?

  I suggest you try the steps mentioned below.

  Method 1: Run the network troubleshooter utility in Windows 7.

  Please follow the steps below mentioned link to run the network troubleshooter utility

  http://Windows.Microsoft.com/en-us/Windows/help/network-connection-problems-in-Windows?T1=Tab03

  Method 2: You can also check the configuration of your new wireless device.

  Contact your Internet Service Provider (ISP) or wireless device manufacturer to check the configuration of your wireless device.

  I hope this helps.

• I deleted a virus from my computer this morning with Security Essentials, now I can't connect to the internet.

  I deleted a virus from my computer this morning with security essentials, now I can't connect to the internet. The connection icon in the lower right corner of the screen says I am connected and the signal strength is 'very good', but I can't go online. The error message I receive when I right click and 'fix' the connection says: "failed to query TCP/IP connection parameters. Cannot continue. " For assistance, contact the person who manages your network. How can I fix it? The computer is a HP Pavilion dv2000.

  original title: can't get online

  Hello BurnBurn,

  I suggest you to re-installing the driver for your network card. This may involve completely un-installing it and re - install:
  http://support.Microsoft.com/kb/283658

• I can't connect to the internet via my host after uninstalled antivirus software and restart

  I can't connect to the internet via my host after uninstalled antivirus software and restart it.

  I use windows xp on my host computer and all computers in my client. After that I uninstalled the free trial NIS version and restart my host, I lost the internet connection. Tried to restore with the restoration of the system, but when I restarted it, it said the system restore could not be made. I changed it then with my laptop and I can connect to the internet as the host.

  Hello

  This can happen if the uninstall process fails and leaves behind a Symantec registry value. See the following Symantec article.

  Unable to connect to the Internet after uninstalling Norton AntiVirus.

  http://Service1.Symantec.com/support/NAV.nsf/8d071816eedd7cac88256c0e005a96e5/751c3298ab99cf7188256d34006702e2?OpenDocument

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows?

  322756 (http://support.microsoft.com/kb/322756/ )

• After the removal of a virus, I can't connect to the internet, is looking for an IP address, and the RPC server is unavailable, said

  My netbook has a virus so I did a scan and remove infected files and a program which the virus attached itself to.  Now, I can not connect to the internet.  He is looking for an IP address, and he also says that the RPC server is unavailable.  Any ideas?  Help

  Hello

  Step 1: Start your computer in safe mode, and then try to start the Remote Procedure Call (RPC) services and start the computer in a clean boot
  a. Click Start, type services.msc and press to enter.
  b. in the list of services, double-click Remote Procedure Call services.
  c. change the startup type to automatic, and then click Start.
  d. click ok to apply the changes.

  Reference: http://windows.microsoft.com/en-US/windows7/what-is-safe-mode

• My wireless on my laptop will read the files on my desktop but I can't connect to the internet, my lapto electrician iI unless other computers work well

  My wireless on my laptop will read the files on my desktop but I can't connect to the internet, hard wire my laptop iI unless other computers work fine

  The following diagnostic information:

  1. Connect your laptop wireless so that you can "read the files on your desktop."
  2. Open a command prompt window (start > run > cmd > OK)
  3. Type the following command in the black command prompt window and press enter

     ipconfig/all > "% userprofile%\Desktop\testdata.txt".

  4. Let the window open orders and "hard wire" your laptop to connect to Internet
  5. Type the following commands in the black command prompt window and press ENTER after each one

     ipconfig/all > "% userprofile%\Desktop\testdata.txt".
     Notepad '% userprofile%\Desktop\testdata.txt '.

  6. Copy and paste the contents of the testdata.txt file into your answer here

  Please note that there are 2 for the second command ipconfig > characters.

  You can close and remove testdata.txt (which is located on your desktop) and close the command prompt window.

• I have a WAN Miniport PPPOE problem. Can't connect to the internet.

  I have a WAN Miniport PPPOE problem. Can't connect to the internet.

  Hello

  If you have a Modem and a wireless router or a Modem/Router combination. Read its manual and configure the WAN for PPPOE port.

  http://www.ezlan.NET/PPPoE.html

• I can't connect to the internet after the elimination of the virus and new restore point.

  I use IE8. I can only connect to the internet in safe mode with network.  What can I do to connect to the internet in the normal windows?

  Hello

  When parasites get installed on your computer, they might create hooks in the system computer activities related to the program "Junk" files  When you get rid of the 'Junk' hooks could remain in the system, in the absence of target files (they cleaned) problems are created in the network and Internet related activities.

  If after uninstalling the "Junk", the Internet connection does not work as it should, you will need to restart the operating system parts which get trashed by the process.

  WinSock and TCP/IP update.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  The same processes to refresh the TCP/IP replaces the command typed with.

  netsh int ip reset press enter

  ipconfig/flushdns, press enter

  Restart your computer.

• I recently changed internet service providers and now my Wired desktop can't connect to the internet.

  I recently changed internet service providers and now my Wired desktop can't connect to the internet.  I noticed that the connection is showing 'Automatic private address' can I connect all my fine wireless devices.  I did extensive troubleshooting with my service provider, but they suggest that my master's degree network adapter must be replaced.  I updated the driver, and the device manager says it's working properly. If I connect the same wire for my laptop, it works fine.  This is just my office.  Any ideas how can I fix?

  Hello

  Follow the steps in the KB article below and see if that fixes the problem.

  How to troubleshoot possible causes of Internet connection problems in Windows XP
  http://support.Microsoft.com/kb/314095

• I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.

  I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.  I have Ping www.microsoft.com and the answer is "ping request could not find host www.microsoft.com.  I am connected to the network wireless through my iPad and can connect via my smartphone. This leads me to believe there is only something configured properly on my laptop. Can anyone provide assistance?

  Hello

  You can try a system restore...

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  .. .choose time, until this problem (you may tick to show more older restore points).

  Tricky

• I can't connect to the internet (without thread or cord)

  I bought a new hard drive and had to reinstall the operating system. Everything works fine except that I can't connect to the internet. Everything is connected and all. It has worked before. What can I do?

  Contact your manufacturer for computer/laptop can and ask them how to download the drivers...

  Cheers.

  Mick Murphy - Microsoft partner

• After cleanind my registry with Wise Registry Cleaner, I can not connect to the internet.

  Network connection problem

  Hi all

  After cleanind my registry with Wise Registry Cleaner, I can not connect to the internet. Network LAN and wireless do not work. Windows 7 has diagnosed the problem and says the following:

  There might be a problem with the driver for the wireless network connection card

  Windows could not automatically bind the pile of IP protocol for the network card.

  There might be a problem with the driver for the connection to the Local network map

  Windows could not automatically bind the Protocol IP on the network card stack.

  Details of detection

  Diagnostic information (network card)

  Network card diagnostics information:

  Network adapter driver to connect to the Local network information:

  Description... Broadcom NetLink (TM) Gigabit Ethernet

  Reference the manufacturer... Broadcom

  Provider of... Broadcom

  Version... 14.0.1.0

  The name of the INF file... C:\Windows\INF\oem5.inf

  Date of the INF file... 14.05.2010 21:21:56

  Name of the section... DEV_KEY2. NTamd64.6.1

  Hardware ID... pci\ven_14e4 & dev_1692

  Instance status indicators... 0x180200a

  Status code from device Menager... 0

  IfType......................... 6

  Physical media type... 14

  Similar to Wireless adapt. The problem is probably not the antivirus program, since I have only deinstaled and the problem persists. I've also uninstalled and reinstalled the drivers, but no solution again. I can't do a system restore point before cleaning the registry, because Windows could not find a file that is needed for the restore. I restored again since before saved registry cleaning but no help.

  Any other ideas please. This really seems teribble :(

  Thank you

  Nikola

  Hello

  You can try all reset them TCP/IP and WINSOCK by this order from the high command prompt:

  netsh winsock reset
  netsh int ip reset log.txt

  How to run the command prompt as administrator (high) is here:

  http://Windows.Microsoft.com/en-us/Windows7/command-prompt-frequently-asked-questions

  part:

  How to run a command with elevated privileges?

  LC