I have not installed the Acrobat XI because I was not sure of its authenticity and security. Now, I know I should have clicked on the button install. How to resume the installation process. I presume, without installation, I won't be able to use
Have need of instructions to resume the process of inastallation Acrobt XI failed.
What is the reaction of my answered "so-called" (but not really answered) question?
Tags: Acrobat
Similar Questions
-
I've updated my macbookpro (2010) snow leopard at elcapitan but when I restart it does not complete the installation then is no longer able to use it.
I tried the following:
1 start with the R command and using disk utility that did say he had problems but then appear all ok after completing.
2 tried the Verbose mode and did not work
3. I tried command mode S did not.
4. tried to zap the pram was not working.
5 a couple other things that I had read, but nothing helped.
It starts up and the line begins to show the computer made his 'thing', but gets stuck about 3/4 quarters of and goes no further. Would appreciate any suggestions.
PS: also tried boot from the original disks as well, but no luck.
You said "PS: also starting from the original disks tried both but no luck."
Exactly what happened when you tried?
Have you tried formatting the HD?
Have you started the installation of SL?
-
Hello
During the installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT partition.
I have 64 bit install discs for Win 7 and Win 8.1. These two install on my desktop in duel boot. I made a Flash DRIVE of each disk so I can install it more quickly.
Problem: I get the cannot install because it is a GPT partition.
Y at - there no way to make these 2 USB sticks work?
Thank you, Brad
Make sure you create your media recovery HP or USB Flash Recovery discs before you edit or change anything.
Your computer does not have Microsoft's Downgrade rights and you must buy a copy of Windows 7 with a valid Microsoft COA and product key.
The screenshots below is from a laptop HP 15 t-j100... options and the configuration on your computer screens may differ.
You will need to DISABLE "Secure Boot" and ENABLE "Legacy Support" in the "Configuration of the BIOS start-up secure" on the settings page similar to what is shown below, until you try to install Windows 7.
After you save the changes, the computer will ask you to confirm the changes... Accept the changes by typing the four digit code and press the ENTER"" key.
If you install Windows 7 from a USB and see a message of "load a driver - a required CD/DVD drive device is missing", it's because as 'System Configuration' > 'Config USB3.0 in pre-start' is set to 'Enabled '. This should be set to 'Auto '.
In addition, as the factory hard drive is partitioned as TPG, you must start using the internal CD/DVD UEFI or UEFI-Key/key USB to install Windows on a GPT-partitioned disk. Turn on or restart the computer and press "F9" or "ESC", then "F9" when prompted. Select the source of boot UEFI you use and you press "ENTER".
I suggest using Windows 7 SP1 for the best installation experience. If the DVD does not start as UEFI, you may need to use a USB Flash drive (can ask "Quick start" DISABLING in BIOS) as the installation media. Please note that some computers may not recognize a valid active UEFI USB Flash drive if it is formatted in NTFS and may require only a FAT32 formatted USB Flash drive. You should be able to make a FAT32 formatted Windows 7 installation USB Flash drive using Rufus, UNetbootin, Universal USB Installeror WiNToBootic. I like Rufus, because it contains options for 'Plan of GPT partition for UEFI computer' and 'FAT32'.
If you have any other questions, feel free to ask.
Please click the 'Thumbs Up' white LAURELS to show your appreciation
-
Hi I just bought a copy of Microsoft Flight Simulator gold edition. and after installing and playing on the deluxe edition, I decided to add the extension of acceleration. and after installing the extension, the game no longer works it comes up with an error message saying "Flight Simulator could not load some program files and will now stop. Please reinstall Flight Simulator to restore or repair the installation of the program. ».
Now, after a few days looking for a response, I decided to ask the guy who made the game.
The error message also appears when I download just 2 service packs of Microsoft also.
I have a laptop HP 630 with a processor intel core i3 - 2350 m cpu @2. 30 ghz, 2 GB ram, windows 8 pro 64-bitOriginal title: fsx gold edition...
Try this, it worked for me:
(1) uninstall normally from the control panel.
Reinstall 2) in the Windows directory (C: here)
(3) install SP1, SP2
-
My messages send and receive txt messages not iMessage on my iPhone and I don't know how to solve the problem to send and receive messages as iMessage
Settings > messages > iMessage turn off then turn it back on...
If it does not sign of your apple under messages ID. Settings > General > reset > reset all settings (will not erase data).
Then log in messages
-
had this message for the 1st time on windows, not sure if its real? performancewreckcontrol.in
had this message for the 1st time on windows, not sure if its real?
Hi Netbook,
This isn't enough information. What is the exact message and any word to Word with all the codes? How it was received (a pop-up, aredirect, an e-mail (if so, what he want/say - leaving out personal information about you)?) What were you doing when it was received? Do you know what program sent you him? What operating system? What browser and version? What security programs (names and versions of all of them? The message say? When it seemed (start-up or during work)?
Here's help on how to respond to that and other information necessary to understand: http://support.microsoft.com/kb/555375.
In the meantime, I would do anything he asked and guess that it's a scam, spam, malware and/or until we prove otherwise based on your comments.
Thank you!
Kosh
-
I get this error "Flight Simulator could not load some program files and will now close" - does anyone know how to solve?
Hello
I suggest you to please follow the steps described in the following articles and check if it helps.
"Invalid product key" error in Microsoft Games, MapPoint, or Streets & Trips
http://support.Microsoft.com/kb/812467
How to get a new product key for Microsoft Games for Windows, Streets & Trips, or MapPoint
http://support.Microsoft.com/kb/973457
Let us know if it helps!
-
I am looking to buy the version of creative photography of cloud. Will I be able to use it on multiple computers or just one that I buy and download it?
An allowed activation through registration in your AdobeID CC license on up to two computers at the same time. You can install it and more, but you can allow only on two at a time.
-
I am traveling to the United States to Australia next spring. I'll be able to use my iPhone AT & T 6 + for calls, texts and maps here?
Yes, but it will be expensive as you will be traveling. Contact ATT to see what offers they offer when traveling.
-
I'm running Windows 7 Ultimate on my Toshiba Tecra A4-S211 and provided that the installation went, it seemed that took place without incident; except that when I try to start windows I see: "Starting windows" followed by "Setup prepares your computer for first use" that is displayed for about 3-5 seconds and then it restarts and displays abruptly: "cannot start Windows. A recent hardware or software change might be the cause. "I tried the safe mode, but also"last known good configuration"and I get the same results. Finally, I tried the repair function on the installation disc and says am Startup Repair is unable to repair the computer automatically, where then I click to send information to Microsoft to be told that if I had all the devices attached like a camera or portable music player to remove them and restart. I have nothing set, no flash player or anything.
I tried to do all the steps above a dozen times each, and the results are consistent, except that the start of repair is sometimes said that there is nothing wrong with windows. Here also to point out that I had XP running on it before without problem and I tested the DVD on another computer and it worked.Hi Austin,.
You can try some of them in Mode safe - tap F8 repeatedly that you start.
If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
protected. The manufacturer of your system will also sell the physical DVD cheap since you already
Clean Windows. You can also do an ERD on another computer.Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
return and then try to startup repair.)How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlWhat are the system recovery options in Windows 7?
http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7Try the disk Options recovery or Windows 7 startup repair.
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlAlso from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlThen run checkdisk (chkdsk).
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.htmlRetry After Chkdsk startup repair.
If after those you can try the system restore to fashion without failure or the valuation or Windows 7
disc.How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html--------------------------------------------------------------------
If you need to repair disks - these help repair Windows not re-install.
How to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html======================================
If necessary:
What to do if Windows does not start correctly
http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctlyHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlWhat are the system recovery options in Windows 7?
http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7How to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlFollow the steps in this link as well.
-
I spent the day writing a driver for my new general i/o board for LabView using the creator of project pilot such Instrument indicated on the latest LabView tutorials. It works fine on my computer, even incorporated in the Panel 'Instrument i/o' on the toolbar. Really great.
But! This must obviously be something that I can publish on a Web site or email to people for them to install on * their * computers! I tried to use the configuration settings as described in another tutorial in order to produce a zip file, a source folder and a Setup program. However, none of these export options seems to produce a labview library that can be opened without nasty error message on the files being found. Of course, the files are present in the directory, but it is looking for them in the * original * folder instead of either the file installation or a folder in a directory from the file to the library. It's really quite absurd, so I guess I'm doing something wrong... but I can't find information on how to do this right. When I followed the instructions I can find, it does not at all.
What I * should * was that, if I created an installer, when an end user with LabView installed ran the installer it would integrate the new Instrument of e/s vi in their panel of LabView. But this does not happen. In addition, when you look in the installation directory (by default not the LabView directory), but a directory in Program Files/driver-name all the files are there. But if you open the library in the directory of the Volume, he complains about the vi being in the wrong place, then load them in the wrong place.
It seems clear that the behavior of the installer must be to put the appropriate files in the location where LabView research instrument drivers. That is not that this disturbs the bajeezus out of me. Can someone explain me or give me a link to the instructions how to accomplish this feat apparently obviously necessary? I can possibly download my driver to the network NOR, but I want to at least test it out first!
I've attached a zip file of the installation directory, which I do not understand in the runtime environment for reasons of size. I've also attached a zip file of the original directory. It won't work unless that place in the correct location in the folder of LabView. He probably has an older version of I've been using the build options.
I think I got this figured out, maybe, others may use the solution.
On the "Source Files" category in the specifications of construction for an installer, [LVDIR] represents the LabView installation directory. So, if you create the directory instr.lib under [LVDIR], you are installing in the root directory of the instr.lib. Then, create another folder named identically in your project source directory (so that it can find the files) and mark in the installation directory. On the side of the project view, open 'My computer', choose your lvlib on the left and your installation on the right directory and click on the right arrow between the two panes. This will create an installation directory structure in the correct location on the target.
-
Problem the installation / setup an ESXi 3.5 for use with rccmd
Hello everyone!
As I mentioned in the topic, I tried to install / configure rccmd on an ESXi 3.5 software.
We have 2 different methods to implement the required functionality.
1. install a virtual machine to launch the stop on because.
2 live rccmd with the service console install.
We decided to implement the 2nd method and everything works except for signal did not go through the process of rccmd listening.
There is a command to configure the software firewall on an ESX 3.5.x.
I guess, it's esxcfg-firewall < parameters >
The Question is:
Is there an equivalent for the command mentioned in the version of ESXi 3.5?
Alternatively, if not, how to implement a pass through to close?
Thanks in advance!
MGruel
There are no firewall in ESXi. You will not be able to use the rccmd either. Take a look at http://communities.vmware.com/docs/DOC-9531
Unless you're on U3 or earlier, you will not be able to use the script but maybe he can give you advice. Have a search in the forums of ESXi 3.5 for the shutdown of the UPS. There are other references.
-
The so-called Ralink APS does not appear on my network and I don't know who or what he is.
RALINK APS appears on my network. I'm the only person on my network. I've been hacked so many times it's RIDICULOUS. It comes and goes... I can't remove it. The manufacturer is Ralink Technology, model: Ralink model of Access Point, model number RT2860's serial number: 12345678, MAC address is: said 00.26.f3.64.b2.98, IP address: unavailable.
I have a router, a stand-alone modem, I use avast and security systems prev. This router should not be on my network. When it appears, it is as if someone else has control of my computer. Have I been hacked again? Can someone please help?
original title: network Hacking
I have Windows 7 64 bit. It seems not to be in the file you mentioned above. The properties of said TeamViewer amended 10/17/11. I guess I'll just try to remove it from my office. FYI: I just checked and RalinkAPS is on my network as we speak.
Thanks for your help. Any other suggestions?
Yes - I don't know why the other person told you to uninstall TeamViewer in fact (it was not installed - once again you had on your desktop * was * installer - not a shortcut to run it.) - but I think that this will address the initial question:
He could have you some of the same symptoms as you have described - but could so many other things.
As for being pirate - not so sure you have visited.
My suggestion for you...
Make sure that your firewall of Windows 7 is activated without exceptions (No. Exceptions selected.)
Change your password for router something which is less than 15 characters and contains at least three of those four things: letter uppercase, tiny, number and symbol.
Buy these two products:
- eSet NOD32 AntiVirus (just the Antivirus, not the sequel) (~ 59 USD/2 years)
- MalwareBytes AntiMalware (25 USD)
Uninstall/remove any antivirus/antimalware you use and install these two things, register / activate them and let it automatically update and scan at least once a week (you can schedule scans with both of them.)
Change all of your passwords online (at least the ones you can) so that they also follow the same rule set (but not the same password) I gave above on your password for the router.
Keep your Windows operating system and all installed applications UPDATED.
Backup copy.
-
Original title: error loading the c:\ProgramFiles\CommonFiles\parentoLogic\UUS2\UUS.dll module could not be found
I'm cluelss and generally ignore this message. Should I try hard or leave?
Thank you
This link may be a little more useful:
http://www.utilitysoftwarereviews.com/how-to-remove-ParetoLogic-uusdll-error-message/
-
Internet does not peak 1102w after change and security password reset? do not see?
Why do usually see the 1102w after a change in internet security settings and a password reset?
Hi shakepoundsoff,
If you have made changes for your safety, you must re-run the installation program for the printer to detect the network. The printer is always looking for the network on the old security settings.
Maybe you are looking for
-
I do not see that the email has been sent to sent folder
I would like to see to whom I sent emails to my sent folder and cannot find a way to docan someone help me?
-
How can I remove an application at the bottom of my screen to open applications?
When I double click the home button to bring up the screen to open apps, there is always a bar Amazon Video below that says something like "Hello, Lucy." The app is certainly not open, so I see no reason to make it on the screen of the open applicati
-
Hello At one point in the upgrades of the Mavericks with El Capitan, broken rules in Apple Mail. I used to have a rule: If the [email protected] message arrives, copy it into an IMAP folder - so I can see it on my devices - and move it to my local folder f
-
HP Officejet Pro 8610: HP 8610 - check printing order
HE CAN NOT FIND 'SWITCHES' TO CHANGE THE PRINTING ORDER. Control Panel ... Devices and printers ... right click on the printer icon ......... Printer preferences NO option to change the order of printing on any tab QuickBooks Pro ... File ...... Prin
-
Where can I get the latest Firmware UJ - 822S for Portege S100?
I'm looking for the latest firmware for this drive. The drive came with the Portege, and I know that they are specific OEM. There are later versions of the firmware available on other sites of manufacturers, but these will be simply screwed to the dr