I installed ESX and vCenter.  Now what...

Similar Questions

• How to configure ESX and vCenter with two areas virtualized?

  Hi all

  I'm quite new to VMware please bare with me, I'll try to get to the point.

  I am building a new infrastructure for a customer which will look something like the image below...

  My questions concern vCenter and the best way to install it and configure it, taking into account the environment below.

  (a) is it possible for vCenter to manage these two areas, even if they are completely separate?

  (b) how to configure the physical server Win 2008 in what concerns an area? If both virtual areas have their own domain controllers is to say 'Live-domain' and 'Test-domain' box Win 2008 won't belong to one, so what do I do with it? I can't join the party to another area because it is not a. And I can't let a working group.

  Any advice would be much appreciated

  

  That sounds right. Yes, the ESX host will meet your virtual domain controller's DNS information. DNS is very important in an active VMware with HA cluster.

  Virtual domain controllers (and, as a result, DNS) are fairly mundane, no worries, I designed / management of environments that were 100% virtual (incudling vCenter).

  Make sure that you do not enable the option "synchronize time with host" on the virtual domain controller VMware tools. Otherwise, you will have a loop (with VM, VM host synchronization synchronizes with host). The option is disabled by default.

• Using VMotion with 2 ESX and VCenter

  Hi all

  I just installed with ESX 2 VSphere and & VCenter. I can't use VMotion to migrate a virtual machine running one ESX towards each other.

  My setup is as follows:

  the iSCSI Software initiator.

  data store even shared by 2 facilitators.

  same conf network on the 2 hosts, none vlan used (set to 0):

  • vSwitch0 for the Service console, connected to the network of the company (vmnik0)

  • vSwitch1 for virtual machine network (connected to the company network vmnic1) and VMkernel (for vmotion, connected to the production network: san, vmnic2).

  Error displayed (at 10%): a general error occurred: the VMotion failed because the ESX host failed to connect to the VMotion network, please check your physical network configuration and settings network VMotion.

  vmnic2 on ESX1 is configured with 255.255.0.0 192.168.130.X mask and connected to eth0 on iSCSI SAN

  vmnic2 on ESX2 is configured with 255.255.0.0 192.168.131.X mask and connected to eth1 on iSCSI SAN

  Thanks for help

  alelievre wrote:

  vmnic2 on ESX1 is configured with 255.255.0.0 192.168.130.X mask and connected to eth0 on iSCSI SAN

  vmnic2 on ESX2 is configured with 255.255.0.0 192.168.131.X mask and connected to eth1 on iSCSI SAN

  Two VLAN different connection to the iSCSI SAN. You should have the same subnet, but a different IP addresses (if any) connecting to the San from each host (depends on the SAN)... For example 192.168.130.25 for ESX1 and 192.168.130.30 for ESX2. Unless your SAN network covers actually two subnets on your local network, you create a question where you don't need to. I would also use separate NETWORK card for vMotion traffic and another for iSCSI. Separate them VM traffic too (makes everything cleaner and less chance of collisions and too load performance causing one issues for each other. This is why it is a good idea to have at least four, if not six, physical NIC (or ports) within an ESX/ESXi server.

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• Firewall between ESX and vCenter vLAN & Production vLAN

  Hello

  Scenario:

  2 ESX hosts with Teddy bear 6. 2 to vLAN S.C. & VMotion, 2 to vLAN DMZ and 2 for the Production of vLAN.

  There are 2 pSwitches to battery-Mode Cluster, having 4 VLANS.

  1. Production of vLAN1

  2. vLAN2 DMZ

  3. Service vLAN3 console

  4. vLAN4 VMotion

  Connectivity is fine no problem. All VLAN works them very well. Service console and VMotion they fold each other so pSwitch failure failure or Teddy bear.

  Requirements:

  Service console is connected in vLAN3 which is 172.16.20.0/24 network under vSwitch0 contains 2pNICs & 3 exchanges.  Service Console PortGroup, VMotion PortGroup & vCenter PortGroup. vCenter PortGroup I want to place the VirtualCenter VM & I'll put the virtual computer's firewall.

  Currently, the Center Virtual under vCenter PortGroup, which is 172.16.20.55. Communication to ESX all very well.

  How I connect to VirtualCenter & ESX host while I am putting in the Production vLAN? I added a static Route in my P.C. 172.16.20.0 to go via 128.104.145.149 "this is the IP address pSwitch" I connect very well without any problems. Of course that does not protect the farm ESX and virtual Center.

  I want to secure the connection between the Production vLAN & Console of service of VMotion vLAN & get rid of the Static Route in the computers in the Admin.

  Bypass the Options:

  1. Physics MS ISA Server with 2 natachasery one be connected in the vCenter PortGroup & to be connected in the Production vLAN & open ports to demand it.

  2. Physical firewall of Teddy 2 a be connected in the vCenter PortGroup & to be connected in the Production vLAN and open ports require.

  3. Virtual Firewall 'SmoothWall or ISA Server' with 2 teddy bears that are connected in the vCenter PortGroup & to be connected in the Production vLAN and open ports require.

  Please take a look at the diagram attached & tips.

  Best regards

  Hussain Al Sayed

  Hello

  On your diagram, I would change your colors. Orange traditionally involves a DMZ not green, but it is up to you. I use Smoothwall for exactly the same behavior.

  Network <-> pNIC1 <-> vSwitch1 <-> vFW (smoothwall) <-> DMZ Network
  ....................................................<-> Green Network
  

  If your front firewall controls access to everything. You can use 'two' firewalls so if you just want to have a set of Red<->Green Networks. On the first, the Red network is outside, green is the demilitarized zone, in the second, red is the demilitarized zone and the ESX hosts are green.

  To grant access to your ESX hosts from a system outside the firewall, you must enable and redirect port 443 to the appropriate location. In fact, I wouldn't do that, create a virtual machine or physical box that is inside the firewall, use the VPN and OpenVPN Tarek Smoothwall addon in the internal location or create a pinhole that allows RDP access to this host/VM and then use the VIC of in the "green network". You must put the kingpins holes in your firewall to grant access you need, so a VPN works much better. You want to limit the number of holes of PIN you use.

  What you describe is quite feasible, but without the holes of the kingpins and proper routing through the firewall is not possible.

  Best regards

  Edward L. Haletky

  VMware communities user moderator

  ====

  Author of the book "VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.»

  Blue gears and SearchVMware Pro Articles: http://www.astroarch.com/wiki/index.php/Blog_Roll

  Security Virtualization top of page links: http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links

• Conflicting build # reported by ESX and VCenter

  I've recently updated some hosts to the 2011 Rollup pack v3.5.0 (using "esx - 3.5.0_June2011Rollup - 391406.iso").

  They point to build 317866 in VCenter and build 391406 when I use 'vmware - v' of the shell.

  Before this update, they reported build 153875 (not me remember not for sure if I got this VCenter or ESX, based on my history of shell commands, I think it was the first).

  This could be the cause?  I have attached the result of "esxupdate query" to one of the servers.

  My apologies if this is the wrong forum; as I don't really know if there is a problem of VCenter or ESX, but as VCenter is that which appears in the account of the 'bad' thing, I think I would start here.

  That is what I see in VCenter.  How do I change this?

  N ° there is no need to update the version pass. There is no problem with him.  You can continue your work. Once vmware releases the latest patches, you can go ahead and install it: as he has a difficulty and RPM is included. Who should replace the old version with the most recent.

  I hope this helps.

• HP Pavilion 23-g013w: recovery of operating system, replace hard drive and memory now what?

  My hard drive stop working on my HP Pavilion 23-g013w all in one computer. I replaced it with a new 1 TB hard drive. I also installed new memory Crucial upgrade to 16 GB.   All new "hardware" is installed on the computer. When he came she said "Please install operating system on your pc" I ran to the verification of memory and the hard disk check and they both passed.

  I had this all in one at Wal-Mart 2 years ago and it did not come with the recovery disk or they were lost.

  Is there a way to connect with ethernet and download the software, I need?

  Otherwise, what is my next best option... .or not?

  Thank you.

  Thank you very much for the help.  I will continue to "hold" on the line...  Good day.

  Aaron

• No cluster after esx and vcenter 4.0 to 4.1 upgrade

  Hello

  I installed my vcenter (4.0) server to a new server (4.1) with the new ip address and the new host name. I used the datamigration tool and there is no error in the log of the backup and the restore.

  Start all services, but when I connect with the new client, I see only the server vcenter and nothing under

  You have an idea?

  see if the item is useful

  http://KB.VMware.com/kb/1024380

• Cmdlet to find ESX and vCenter

  Hi all

  I use the following cmdlet to connect to ESX/vCenter.

  $vcServer = Connect-VIServer-server: $global: ipAddress-user: $global: vcUser-password: $global: vcPass

  I want to know if I connected to vCenter or ESX after login. Please help me.

  Kind regards

  Bharath

  The ProductLine property will tell you if it's a (vpx) vCenter or ESX (i) (esx) Server

  $vcServer | Select ProductLine

• Calibrated and profiled: now what?

  Now that I have calibrated and profiled my new screen NEC P221W w / puck/software SpectraView II (using a MacBook Pro w / OS 10.6), is there something else I should do to PSE8 to use the new profile?
  
  Thank you for your help.

  You are welcome. Please mark this as good response so that others can also benefit from this.

  Thank you

  Garry

• 4.1 and vCenter ESX only allows to use 1 Fibre Channel LUNS

  Hello

  I have 8 blades ESX 4.1 (build 348481) in a Cisco UCS 5108 chassis. Each blade has 2 x HBAs available. I also have a fiber channel storage array that is configured to provide 2 1.8 to LUN (for now and in the future).

  When I go in vCenter and select one of the ESX servers under "Configuration"-> "Storage adapters"-> "Rescan all...» "each server detects the table (and several paths towards it) but only shows a single available LUNS (LUN 0) when 2 LUNS should be available (LUNS 0 and 1 logical unit number). See the image below.

  

  Now, the thing that confuses me is that when I get on the command-line of the ESX via SSH server and run "esxcfg-mpath - b", I see a list of all the paths including the paths to the LUNS 0 and 1 logical unit number (see output below). Any ideas on why ESX and vCenter authorizes me to LUN 1?

  esxcfg-mpath - b:

  NAA.600508e0000000001e10a036bc3f5601: FREE Serial Attached SCSI Disk (naa.600508e0000000001e10a036bc3f5601)
  vmhba0:C1:t0:l0 LUN:0 Status: active sas adapter: 5c84c75ed0910000 target: 1563fbc36a0101e

  MPX.vmhba32:C0:t0:l0: Local USB CD-ROM (mpx.vmhba32:C0:T0:L0)
  vmhba32:C0:t0:l0 LUN:0 Status: Active Local HBA vmhba32 channel target 0 0

  EUI.706f636c6162766f: disc SCST_FIO Fibre Channel (eui.706f636c6162766f)
  vmhba2:C0:T1:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f2 WWPN: 21:00:00:24: ff: 32:10:f2
  vmhba2:C0:T1:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f2 WWPN: 21:00:00:24: ff: 32:10:f2
  vmhba1:C0:t0:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c2 WWPN: 21:00:00:24: ff: 32:45:c2
  vmhba1:C0:t0:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c2 WWPN: 21:00:00:24: ff: 32:45:c2
  vmhba1:C0:T1:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c3 WWPN: 21:00:00:24: ff: 32:45:c3
  vmhba1:C0:T1:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00: target: WWNN: 20:00:00:24: ff: 32:45:c3 WWPN: 21:00:00:24: ff: 32:45:c3
  vmhba2:C0:t0:L1 LUN:1 status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f3 WWPN: 21:00:00:24: ff: 32:10:f3
  vmhba2:C0:t0:l0 LUN:0 Status: active CF adapter: WWNN: 20:00:00:25:b5:00:00:ae WWPN: 20:00:00:25:b5:00:00:1e target: WWNN: 20:00:00:24: ff: 32:10:f3 WWPN: 21:00:00:24: ff: 32:10:f3

  MPX.vmhba32:C0:t0:L1: USB Direct-access locally (mpx.vmhba32:C0:T0:L1)
  vmhba32:C0:t0:L1 LUN:1 status: Active Local HBA vmhba32 channel target 0 0

  MPX.vmhba32:C0:t0:L2: USB Direct-access locally (mpx.vmhba32:C0:T0:L2)
  vmhba32:C0:t0:L2 LUN:2 status: Active Local HBA vmhba32 channel target 0 0

  Its because the table shows two LUNS have the same value of ID of Page 83, ESX both think you have 2 paths to the same LUN.  Paths multiple ESX driver uses the value of the ID of Page 83 to determine if 2 LUNS are the same device.

  It was a problem with that code, that it resembles yours-based Solaris beginning according to the tables and other tables that used code based on Solaris pre-COMSTAR, as well as tables that use SCWIST.

  There is really nothing you can do about it, because it is a bug in the software of the array (it shouldn't be exporting 2 LUNS different with the same ID value of Page 83 - it is a violation of the standard).

• Is there a "ESXi and vCenter Setup Guide" available?

  I downlaed 'ESX and vCenter Server Installation Guide 4.1 ESX' PDF, but I need an ESXi version as I want to know rather than ESX ESXi score structure.  Is there a same doc for ESXi avaiable?

  Thank you!

  You can find a great description of Rickard Nobel at http://rickardnobel.se/archives/776

  André

• vDS and vCenter

  Hello

  Is it true that if vCenter falls down for more than 24 hours we will lose all switches connections vDS?

  Kind regards

  Have you checked this blog?

  http://www.yellow-bricks.com/2012/02/08/distributed-vSwitches-and-vCenter-outage-whats-the-deal/

• Installed the server VCenter simple install, now what?

  I just finished installation install simple VCenter Server. I'm confused on what to do now. When I look in the VMWare folder in the start menu, I see VCenter client Orchestartor, but I don't know the connection. I'm reading on a device to VCenter Server but do not know if this is a separate installation or what. With respect to the VCenter Server for VSphere Client pluging, I am unable to install it. When I go to manag pluge-ins I installed plug-ins and plug-ins available, but nothing happens when I click on them. If I hit help that an error message appears that says "reference object not set to an instance of an object.

  Any help is appreciated. I suppose that here is my main questions.

  What is the next step after the Installation in VCenter Server?

  What is the main of the application to manage your VCenter Server?

  What is my plugin error?

  With simple installation, you have installed vCenter Single Sign On, the inventory Service and vCenter Server on the same host. Now, all you have to do is install the vSphere vSphere Client Web Client and make sure you can access the instance of vCenter server.

  Install the vSphere Client;

  http://pubs.VMware.com/vSphere-51/topic/com.VMware.vSphere.install.doc/GUID-1F4EB138-3301-4AC9-9B48-61166E0EBE24.html

  I recommend reading the post installation documentation, which contains all of this information;

  http://pubs.VMware.com/vSphere-51/topic/com.VMware.vSphere.install.doc/GUID-5C6223B4-3E9E-4DD1-82D2-DCC78DFD5C18.html

  Can you post a screenshot of the plugin error?

  See you soon,.

  Jon

• I want to install windows on my new macbook and I need to create a partition. I have not now what size to make my windows partition. Can someone give me some advice?

  I want to install windows on my new macbook and I need to create a partition. I have not now what size to make my windows partition. Can someone give me some advice?

  1. in what year is your Mac?

  2. What is the size of your storage internal?

  3. what version of Windows?

  4 as a general rule 60-100 GB for W8 + / W10 is recommended. You can also create a minimum Windows (30-50 GB) and use an external drive D: for documents applications for portability.

• I recently bought and downloaded Adobe elements 12 to my laptop. Now, I have another laptop and I would like to install on it instead. What do I have to uninstall on my old laptop first and then download it again and reinstall it on my end

  I recently bought and downloaded Adobe elements 12 to my laptop. Now, I have another laptop and I would like to install on it instead. What do I have to uninstall on my old laptop first and then download it again and reinstall it on my latest acquisition? Roy.

  Adobe license allows 2 activations... so install on 2nd computer in the same way as you did on the 1st computer, enter your serial number when asked