How to configure ESX and vCenter with two areas virtualized?

Similar Questions

• How can I associate a button with two slices?

  Hello
  I need help please. How can I associate a button with two slices? or combine the two slices to make one cut or make a form of true polygon on the edges, it will make to the polygon, but it leaves the red lines and I cannot work under this installment... If you understand. Someone help please. Thank you very much.

  Two points.

  First of all, I see that you have forms stars in your image, but that does not mean that you need a star-shaped slice. You can use a little square that is centered on your star. That could make it easier to create your slices. All you have to do is drag lines of leaders in the left seat and superior, two pairs around each star and then drag a slice from one end to the other.

  Noting that brings me to my second point: images must be rectangular. If you want to change the L-shaped area, then you need to swap two images, not one only. This is perhaps why you cannot have the buttons under the threshold of upper sliding of your L shaped section. Because Fireworks needs to make a rectangular image, it is by default in an area that encompasses the range - area you can not the buttons in. It is the lock area non cut which still need to be part of the image, since the part will swap, too.

• Satellite Pro L40 - how to make a dual boot with two recovery disks

  A small question;
  How to dual boot with two recovery disks ive got with my laptop (Satellite Pro L40)

  discs 1 & 2 are windows vista buisness
  discs 3 & 4 are windows xp profesional
  Disc 5 is updated the bios

  The guy where I bougt garage computer (a metal regular store named expert) says that it is posible with discs tose.
  I have
  I already have a partition, but when I boot from disks, is not has the option to select a partition

  Thanks already

  > Satellite Pro L40 - how to make a dual boot with two recovery disks?
  Short answer: you can't do that. Maybe if you have two hard disks (I tried didn't) but as much as I know your SP L40 has only one.
  Ask this smart guy, how to do this. Maybe it's a useful tip.

• How do monitors vecteurscopes and waveform with the new update in first Pro CC?

  How do monitors vecteurscopes and waveform with the new update in first Pro CC?

  Press the COLOR at the top of the interface or go to the window workspace and select Lumetri Scopes.

  If you are a reverence for the old spans: there have been removed in favor of the Lumetri Scopes.

• 810-492nd Phoenix ENVY: how many unused power and sata connectors connectors are there?

  How many unused power and sata connectors connectors are there? I intend to add 2 internal hdd and 1 ssd to the PC.

  Twosix, welcome to the forum.

  HP does not provide this information in the specifications.  However, there are the following drive bays:

  Size of the Bay

• Using VMotion with 2 ESX and VCenter

  Hi all

  I just installed with ESX 2 VSphere and & VCenter. I can't use VMotion to migrate a virtual machine running one ESX towards each other.

  My setup is as follows:

  the iSCSI Software initiator.

  data store even shared by 2 facilitators.

  same conf network on the 2 hosts, none vlan used (set to 0):

  • vSwitch0 for the Service console, connected to the network of the company (vmnik0)

  • vSwitch1 for virtual machine network (connected to the company network vmnic1) and VMkernel (for vmotion, connected to the production network: san, vmnic2).

  Error displayed (at 10%): a general error occurred: the VMotion failed because the ESX host failed to connect to the VMotion network, please check your physical network configuration and settings network VMotion.

  vmnic2 on ESX1 is configured with 255.255.0.0 192.168.130.X mask and connected to eth0 on iSCSI SAN

  vmnic2 on ESX2 is configured with 255.255.0.0 192.168.131.X mask and connected to eth1 on iSCSI SAN

  Thanks for help

  alelievre wrote:

  vmnic2 on ESX1 is configured with 255.255.0.0 192.168.130.X mask and connected to eth0 on iSCSI SAN

  vmnic2 on ESX2 is configured with 255.255.0.0 192.168.131.X mask and connected to eth1 on iSCSI SAN

  Two VLAN different connection to the iSCSI SAN. You should have the same subnet, but a different IP addresses (if any) connecting to the San from each host (depends on the SAN)... For example 192.168.130.25 for ESX1 and 192.168.130.30 for ESX2. Unless your SAN network covers actually two subnets on your local network, you create a question where you don't need to. I would also use separate NETWORK card for vMotion traffic and another for iSCSI. Separate them VM traffic too (makes everything cleaner and less chance of collisions and too load performance causing one issues for each other. This is why it is a good idea to have at least four, if not six, physical NIC (or ports) within an ESX/ESXi server.

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• How to configure vMotion and storage?

  I'm trying to set up with vMotion HA. I can see how the virtual appliance can be moved to another physical server. How to configure storage, so that data are available on the new server?

  Thank you.

  You cannot share your local storage space. That is unless you use a third-party application that turns your local storage space in your storage SAN Lefthands VSA. Think of it like this, you have two servers ESX (ESX1 and ESX2) you have a virtual machine with the disk it's on ESX2. If ESX2 fails, off, etc. it is impossible for the drive be accessible. HA is still based on a shared storage access to the virtual computer files.

• Firewall between ESX and vCenter vLAN & Production vLAN

  Hello

  Scenario:

  2 ESX hosts with Teddy bear 6. 2 to vLAN S.C. & VMotion, 2 to vLAN DMZ and 2 for the Production of vLAN.

  There are 2 pSwitches to battery-Mode Cluster, having 4 VLANS.

  1. Production of vLAN1

  2. vLAN2 DMZ

  3. Service vLAN3 console

  4. vLAN4 VMotion

  Connectivity is fine no problem. All VLAN works them very well. Service console and VMotion they fold each other so pSwitch failure failure or Teddy bear.

  Requirements:

  Service console is connected in vLAN3 which is 172.16.20.0/24 network under vSwitch0 contains 2pNICs & 3 exchanges.  Service Console PortGroup, VMotion PortGroup & vCenter PortGroup. vCenter PortGroup I want to place the VirtualCenter VM & I'll put the virtual computer's firewall.

  Currently, the Center Virtual under vCenter PortGroup, which is 172.16.20.55. Communication to ESX all very well.

  How I connect to VirtualCenter & ESX host while I am putting in the Production vLAN? I added a static Route in my P.C. 172.16.20.0 to go via 128.104.145.149 "this is the IP address pSwitch" I connect very well without any problems. Of course that does not protect the farm ESX and virtual Center.

  I want to secure the connection between the Production vLAN & Console of service of VMotion vLAN & get rid of the Static Route in the computers in the Admin.

  Bypass the Options:

  1. Physics MS ISA Server with 2 natachasery one be connected in the vCenter PortGroup & to be connected in the Production vLAN & open ports to demand it.

  2. Physical firewall of Teddy 2 a be connected in the vCenter PortGroup & to be connected in the Production vLAN and open ports require.

  3. Virtual Firewall 'SmoothWall or ISA Server' with 2 teddy bears that are connected in the vCenter PortGroup & to be connected in the Production vLAN and open ports require.

  Please take a look at the diagram attached & tips.

  Best regards

  Hussain Al Sayed

  Hello

  On your diagram, I would change your colors. Orange traditionally involves a DMZ not green, but it is up to you. I use Smoothwall for exactly the same behavior.

  Network <-> pNIC1 <-> vSwitch1 <-> vFW (smoothwall) <-> DMZ Network
  ....................................................<-> Green Network
  

  If your front firewall controls access to everything. You can use 'two' firewalls so if you just want to have a set of Red<->Green Networks. On the first, the Red network is outside, green is the demilitarized zone, in the second, red is the demilitarized zone and the ESX hosts are green.

  To grant access to your ESX hosts from a system outside the firewall, you must enable and redirect port 443 to the appropriate location. In fact, I wouldn't do that, create a virtual machine or physical box that is inside the firewall, use the VPN and OpenVPN Tarek Smoothwall addon in the internal location or create a pinhole that allows RDP access to this host/VM and then use the VIC of in the "green network". You must put the kingpins holes in your firewall to grant access you need, so a VPN works much better. You want to limit the number of holes of PIN you use.

  What you describe is quite feasible, but without the holes of the kingpins and proper routing through the firewall is not possible.

  Best regards

  Edward L. Haletky

  VMware communities user moderator

  ====

  Author of the book "VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.»

  Blue gears and SearchVMware Pro Articles: http://www.astroarch.com/wiki/index.php/Blog_Roll

  Security Virtualization top of page links: http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links

• How to configure HA when vCenter is running as a virtual machine in one of the army?

  To install HA with VMware EVC, guests must be first maintenance mode before moving into the HA cluster. The problem is, vCenter runs as a virtual machine inside one of these hosts. If I stop vCenter downwards so that the host in maintenance mode, how do I setup with VMware EVC HA without using vCenter?

  If you do not feature vMotion, right down your vCenter VM and you unsubscribe eg. ESX1 can record for example. ESX2 then turn back on. ESX1 maintenance mode and then back ESX1 on your cluster file and exit once done maintenance mode. It goes the same for ESX2 and the rest of the ESX host.

• How to configure TB to work with Filemaker 10?

  Hello

  Thanks for any help you can offer.

  I'm on a Macbookpro on 10.6.8. I want to send e-mails via Filemaker Pro 10.0v1. Thunderbird 31.0 is my default e-mail client. I think I must also configure mac Mail somewhere in this process. These e-mails will be turned off on 5wcw.featheredpipe.com located on the webmail via my Web site. This will complicate things?

  Please excuse me if I'm not using correct jargon here - it's new to me. Support FM advises to use Eudora - I hope it's just old info and Thunderbird will work.

  Thanks for any help,

  Linda

  Looks like the real question is how to configure the file creator to work with Thunderbird. Most of the applications like that just use the default mail client. If it does not, you should ask the people to lead Maker how their software works.

• How to configure SCC-Ci20 ISP with SCC-68

  I'm trying to measure a current analog signal using scc-ci20 scc-68 and pci-6221.

  I used the scc-68 for analog measurement signal voltage using analog terminals, so the scc - 68 and pci-6221 are well configured.

  What I did:

  I added the scc-ci20 "measure and explore automated" under the scc - 68, CSC - mod 1

  In the software labview in the DAQ assistant, I added a new channel for current measurement and physical channels appearing were "aio, ai1' which is the channel of the Terminal screw 1 Module and not of the scc-ci20 terminal block.

  Also, I connect to the meaning of the Al to Al GND.

  I don't know, if the DIF in how to configure the current module or how I connect the resistance to the Terminal Board and the scc-68 port.

  Hi Egptos,

  The SCC-CI20 channels are grouped in a differential measurement that is able to fill two separate loops, so the ai0 ai1 and. AI0 is the bundling of channels 1 and 2 on the module, who complete a circuit, and ai1 represents channels 3 and 4 that complement a second loop. The resistance of shunt used by the module to take the current measure is incorporated in the module.

• How to create a vector image with two color fill

  Hi everyone, is there anyone who knows how to make a rectangle to fill with two colors? for example a red pantone 032 C and black.

  What I've done, I've done two rectangles on each other to the same corders.

  The less one I filled out (Pantone red 032C 100% and 100% transparent) and the more with (black 50% and 50% transparency).

  Is it? Is this correct or there is another way?

  Someone help please.

  Œuvres for as many colors as you want. Try it. You should have no problem if you follow my steps.

• Adobe Muse and site with two languages only

  Hi I need help to create the site with only two languages, I translate site myself, had two buttons with indicator of language of site or letters and I need a language priority if the customer wants to choose different language it press the button. It is impossible

  There is probably no other way to do it. You need structures separated two singles. It could be in a field but with two trees of structure (first Te 'base site' index.html and second Te index_ru.html for the translated version) with one link to the other.

• How to select, copy and paste (with translation into English) a Spanish PDF document, for example, Google Translate?

  I have a 64-bit Windows 8.1 PC and use Internet Explorer 11 or Windows Chrome. Can someone talk to me through selection, copy and paste a PDF document in general? As well as my occasional to translate Spanish Pdf document need, I also like to know how to select, copy and paste into Notepad or WordPad, an e-mail or a document. I tried everything I can think but cannot make it work.

  Just FYI: If you have PDF documents online (which contain 'real text' of course), you can also use Google Translate to translate the entire document.  Click 'translate a document' under the entry field.

• Configure Manager node for the two areas in weblogic

  Hi friends,

  I'm kinda new to weblogic. I need help to configure nodemanager to two areas.

  I created two areas

  1 Classicdomain

  2 RPMdomain

  For classic field, I created the machine and all the server has added to this machine.

  MachineName: localmachine

  Port: 5556

  Plain

  For RPMdomain I created the machine with the same name and the port and all servers added to this machine.

  I registered both server using nmroll().

  First domain has been configured with nodemanager.

  In the second area, I am not able to start a stop managed server via the console.

  Could someone please let me know how to configure the nodemanager.

  Kind regards

  Prates

  Are able to launch those instances successfully from the command line using the command startManagedWeblogic.sh? Once you have started it, try stopping through the node Manager and then start it upward.

  Also, do you have JSSE enabled in your case and/or disabled hostname verification? These errors indicate fundamentally flawed SSL handshakes with the node Manager.