I/o device error, unable to write to my DVD player, reusable discs are not recognized

Similar Questions

• Unable to write to the dvd player

  Windows fixit says not able to burn. Have had this problem since reinstalling windows as it comes up with please insert a writable disc

  I have two recorders readers of dvd with the same two errors are displayed as recorders readers. Followed the instructions for this problem which are proved for this problem in the forum. "" clean boot "checked the registry, but in vain. This problem is operational since 2008, according to the answers in the forum.

  Hope someone can help please Gordon

  Hi Gordon,.

  ·         What fixit did you run?

  ·         What is the full error message?

  Follow the steps in the article.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://support.Microsoft.com/kb/322756

• USB devices connected through a USB 2.0 Hub Stop Responding and are not recognized after Hub reconnects

  Recently, I have this strange problem where if I connect an additional USB device to one of my USB hubs, some of my devices stop working (especially my keyboard and mouse).

  I have two hubs Generic USB connected to my motherboard. My motherboard is an ASUS Rampage II Extreme X 58 who and chips ICH10. It has 4 USB ports in the front and 6 ports on the rear panel (all USB 2.0). I also have a USB 3 controller card that is connected to one of the PCI-E card to the Board of Directors.  I have the following problems:

  1. Connect a USB device to one of my USB hubs (or one of the USB ports on the front panel) causes some of my devices to stop working (especially my keyboard and mouse that are connected via a USB hub). It seems that crashes of USB controller.  If disconnect and reconnect my HUB, windows does not recognize devices connected to this hub.
  2. Now, after the crash, if unplugging the devices connected to the hub and connect it directly to one of the ports on the front or the back of the computer, Windows instantly recognizes!

  Now I'm confused what is the cause of this problem. I had the same computer since the release of the i7 and X 58 and never had this problem (although I don't remember if I used USB hubs right there).

  Why Windows to recognise the devices connected to the hub at the beginning, but not after the crash?

  Why USB devices stop working when I connect to another USB device on my computer?

  And how do I solve this problem?

  AK

  Just a thought by the way.  If the hubs are not powered you can cause the + 5V due to the excessive number of devices not powered up to a point where it causes accidents and able to resume.

  Reduce the number of UN powered can solve this problem,

• Fatal error: unable to write to the transaction log

  Hi people,
  
  We get below error when I try to run my project in Jdev.
  
  
  HTTP port conflict detected. The HTTP port is reassigned to port 9041.
  
  JMS port conflict detected. JMS port is reassigned to port 9277.
  
  [Departure OC4J uses the following ports: HTTP = 9041, RMI = 23896, JMS = 9277]
  
  C:\JDEV\jdevbin\jdk\bin\javaw.exe-client - classpath C:\JDEV\jdevbin\j2ee\home\oc4j.jar; C:\JDEV\jdevbin\jdev\lib\jdev-oc4j.jar-Xbootclasspath/p:C:\JDEV\jdevbin\jdev\appslibrt\ojdbc14.jar; C:\JDEV\jdevbin\jdev\appslibrt\nls_charset12.zip-DFND_JDBC_STMT_CACHE_SIZE = 200 - DCACHENODBINIT = false - DRUN_FROM_JDEV = false - mx256m - Xverify: none - Doracle.j2ee.dont.use.memory.archive = true - Doracle.j2ee.http.socket.timeout = 500 com.evermind.server.OC4JServer - config C:\JDEV\jdevhome\jdev\system9.0.3.5.1437\oc4j-config\server.xml
  [waiting for the server to complete its initialization...]
  
  Fatal error: unable to write to the transaction log (/ C:/JDEV/jdevhome/jdev/system9.0.3.5.1437/oc4j-config/log/transaction.state), possible reasons are that Orion does not have permission to write to the file, or that another instance of the server is already running with this (more common) configuration: cannot modify the transaction log
  
  Process has finished with exit code 1.
  [Departure OC4J uses the following ports: HTTP = 9041, RMI = 23896, JMS = 9277]
  
  C:\JDEV\jdevbin\jdk\bin\javaw.exe-client - classpath C:\JDEV\jdevbin\j2ee\home\oc4j.jar; C:\JDEV\jdevbin\jdev\lib\jdev-oc4j.jar-Xbootclasspath/p:C:\JDEV\jdevbin\jdev\appslibrt\ojdbc14.jar; C:\JDEV\jdevbin\jdev\appslibrt\nls_charset12.zip-DFND_JDBC_STMT_CACHE_SIZE = 200 - DCACHENODBINIT = false - DRUN_FROM_JDEV = false - mx256m - Xverify: none - Doracle.j2ee.dont.use.memory.archive = true - Doracle.j2ee.http.socket.timeout = 500 com.evermind.server.OC4JServer - config C:\JDEV\jdevhome\jdev\system9.0.3.5.1437\oc4j-config\server.xml
  [waiting for the server to complete its initialization...]
  
  Fatal error: unable to write to the transaction log (/ C:/JDEV/jdevhome/jdev/system9.0.3.5.1437/oc4j-config/log/transaction.state), possible reasons are that Orion does not have permission to write to the file, or that another instance of the server is already running with this (more common) configuration: cannot modify the transaction log
  
  Process has finished with exit code 1.
  
  
  
  Any solution would be greatly appreciated.
  
  Rambeau

  When you find a solution
  Please indicate your question as answered.
  You should also recognize replies to your thread is useful or appropriate using the buttons where appropriate

  Please read more about the announcement: Please read this before posting
  http://forums.Oracle.com/forums/Ann.jspa?annID=56

  There is no need to explicitly mention who responded to your question. You can score just as helpful or Correct answer.

  Thank you
  AJ

• Vista - usb ports are not recognized unknown device

  Vista - usb ports are not recognized unknown device. any usb device it appears unknown. all worked a few days hardly, but after that I connected my Kodak camera - which does not, now, nothing works. Any help would be appreciated.

  Hello

  Thank you for using the Microsoft Windows Vista Forums.

  Follow the instructions below that may help you resolve the issue.

  Method 1:

  Try to connect USB devices to a different USB port and check if you are able to access.

  Method 2:

  Click on the link below to run Fix it which will help you to solve the problem.

  Tips for solving problems of USB devices

  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx

  Click on the link below and install the update.

  Rollup cumulative update for USB in Windows Vista Basic components

  http://support.Microsoft.com/kb/941600

  Try to connect the camcorder to the other USB port and on the other computer and see if the problem is resolved.

  Method 3:

  Let us try to disable the Antivirus security software and check the number.

  Re-enable the security software after checking the issue.

  You can also try disabling the firewall and check the issue.

  Re-enable the firewall after checking the issue.

  Method 4:

  A clean boot helps eliminate software conflicts.  Let us check if software is causing the problem by following the clean boot procedure.

  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot

  Step 2: Enable half the services

  Step 3: Determine whether the problem returns

  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns

  Step 6: Resolve the problem

  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista

  http://support.Microsoft.com/kb/929135

  After checking the problem, turn the computer back to the Normal mode.

  Uninstall or update the program that is causing the problem.

  Check whether the problem is resolved.

  You can also check out the link below.

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/6be4581d-8fbd-407F-815E-b475c35ca586

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP

• My USB devices are not recognized, but they have a power

  My USB devices are not recognized, the only ones to be recognized are my mouse and keyboard. Each device is powered (motherboard works fine), but Windows 7 isn't their read (although sometimes I'll get a code 43). I have the latest chipset.

  I tried right click and uninstall each device and rebooted the computer. Nothing has fixed this.

  My external hard drive, ipod and other devices that involve the transfer of data seem to ONLY get power and nothing else.

  It is not material because all my devices work on my laptop. Also my motherboard works fine (it's the 2nd RMA) and it has been tested at the factory to make sure of him.

  I would really appreciate help with this

  Hello

  Please follow the methods.

  Method 1:

  Run the troubleshooter from the link.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

   

  Method 2:

  Try to uninstall and reinstall the USB controllers

  a. click the Start button.

  b in the start search box, type devmgmt.msc and press enter

  c. expand Bus USB controllers

  d. right-click on the first USB controllerr under Bus USB controllers and then click Uninstall to remove it. Repeat these steps for the entire USB under Controllers USB Bus controller.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  I would also ask you to contact the manufacturer of the computer to help.

• Error ERR - 10768 current Application ID and security group ID are not the measures

  Dear all,
  
  I had the default below code in my login page and it was running fine.
  
  (wwv_flow_custom_auth_std). Login
  P_UNAME = >: P101_USERNAME,.
  P_PASSWORD = >: P101_PASSWORD,.
  P_SESSION_ID = > v ('APP_SESSION').
  P_FLOW_PAGE = >: APP_ID | » : 1'
  );
  
  Then I replaced the code above with the code below, and now he's in error "error ERR - 10768 Application ID and current security group ID are not constant".
  I can't understand what is wrong with the code. Please correct me where I am wrong.
  
  declare
  vpage_no number 4;
  Start
  
  If: P101_USERNAME = "DEMO" then
  vpage_no: = 2;
  on the other
  vpage_no: = 1;
  end if;
  
  (wwv_flow_custom_auth_std). Login
  P_UNAME = >: P101_USERNAME,.
  P_PASSWORD = >: P101_PASSWORD,.
  P_SESSION_ID = > v ('APP_SESSION').
  P_FLOW_PAGE = >: APP_ID | vpage_no
  );
  end;

  Yousuf,

  You did not follow the convention used in the original, try:

  P_FLOW_PAGE =>: APP_ID |': ' | vpage_no
  );

  Scott

• Error message: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete" and DVD disc is not recognized.

  Original title: My DVD drive is not recognized, it works physicaly works fine, but the pc does not even detect it exists.

  The error that says: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete."

  I did a backup and restored my system to the factory settings. After doing this still dvd was not recognized. I don't know what to do, my computer is new and Security told me that they will restore the pc and try to fix it, I can't risk my documents of the University are the same that has not worked for me before.
  Could someone help me?
  -The pilot is the last in line.
  -The works of reader dvd but the computer is not reading it, it does not even appear on the section 'computer '.
  -J' tried to use a "fix - it" on Microsoft online, but it doesn't work anymore.
  -My OS is Windows 7.
  -A restore factory settings did not work at all.
  Thank you.
  Claudio Nahmad
  Mexico City

  Hi, Claudio Nahmad,.

  This error can occur if the data in the registry for the device and its driver has been corrupted.

  Since you have already done a factory restore, leave, try to uninstall and reinstall the driver CD\DVD and check if it helps.
  Code 19: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged

  We can also refer to article and check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Important: The above links contains steps to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information, you can view the article:

  Back up the registry

  You can also try to install Windows updates, including optional updates driver and check if that helps.

  Install Windows updates in Windows 7

  Hope the helps of information.

• Error code 19 registry on any DVD player.

  I get the following message when I install a DVD drive on my laptop CQ60 Compaq Vista home edition 32 bit running.

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I tried to uninstall and install this unit several times.  I tried to install a USB DVD drive as well (and uninstall) and get the same error.

  Seeking solutions sends data to Microsoft (apparently) but I have no feedback.

  I don't see an option "UNINSTALL - REBOOT.  I uninstalled the devices (Optiarc AD-7561 and the DVD ROM Targus USB drive) and restarted the computer.  When both are installed, I get the same error from registry

  Hello

  UNINSTALL you then RESTART when back in Device Manager - which means rebooting the system.

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• USB 2.0 devices are not recognized on Satellite L

  Hello

  All of the usb 2.0 device is not recognized on my laptop.
  I got a message stating that the driver are not installed. I'm looking for the driver on the support site, but could not find them...
  I've updated the bios and chip set utility, but still nothing.

  Any idea?

  Hello

  What model of laptop do you have?
  What operating system do you use?
  Since when you noticed this problem?
  Did you test all USB ports?

  Have you tested with different devices USB ports?

  Please post a little more information.

• ArraytoChannels error 'cannot be added because the channels of the target are not all the same length.

  Hello!

  After the end of my second day of test error, I put this question on the table:

  I use ArraytoChannels function to store ADO recordsets as strings. What is strange, is that for the first Recordset, it works; but for the next time through the loop, it always fails with the error message 'cannot be added because the channels of the target are not all the same length.

  I confirmed that:

  the RowData sizes and the ChannelNames are equal,

  both spend the isarray = true test,

  I change the order of the ChannelNames,.

  I have reconnected/disconnected from the oConnexion every time, nothing has changed.

  Apparently I'm missing something - but crazy to know what! -If anyone can share his opinion I'll so much appriciate. Here is my code:

  oTables = Array ("WellStates", "ChokeData", "WellParameters", "FlowData", "PumpData", "SensorsData", "ModelCalculatedData")

  Call OpenSQLConnection
  Set oRecordset = CreateObject ("ADODB. Recordset')
  Call SelectWell
  Call GetWellStateIDs

  Data.Root.Clear
  for j = 0 to ubound(oTables,1)

  sSQLSting = "select * []" & oTables (j) & "] where [WellStateID] between" & WellStateIDFirst & "and" & WellStateIDLast ".
  oRecordset.Open sSQLSting, oConnexion
  Protected oFieldNames: table: ReDim oFieldNames (orecordset. Fields.Count - 1).
  for i = 0 to orecordset. Fields.Count - 1
  oFieldNames (i) = orecordset. Fields.Item (i) .name
  next
  oArray = oRecordset.GetRows (-1, 0, oFieldNames)
  Set oGroup = Data .root .ChannelGroups .Add (oTables (j))

  oArray, oFieldNames arraytochannels
  oRecordset.close
  oConnection.Close
  next

  Sub GetWellStateIDs
  sSQLSting = "select * from [WellStates] where [wellid] =" & WellID
  oRecordset.Open sSQLSting, oConnexion
  oArray = oRecordset.GetRows)
  WellStateIDFirst = oArray (0,0)
  WellStateIDLast = oArray (0, ubound(oArray,2))
  oRecordset.close
  EndSub

  Sub OpenSQLConnection
  Set WshNetwork = CreateObject
  oComputerName = WshNetwork.ComputerName
  oDB = "MX2. Player.DB ".
  Set oConnexion = CreateObject ("ADODB. Connection")
  oProvider = "Provider = SQLOLEDB.1; Integrated Security = SSPI; PeoExecuteist Security Info = True; Data Source ='
  oProvider = oProvider & oComputerName & "\MX; Use procedure for prepare = 1; Machine translation = True; The packet size = 4096; Workstation ID ="
  oProvider = oProvider & oComputerName & " Use encryption for data = False; Tag with column collation when possible = False; Initial Catalog ='
  oProvider = oProvider & oDB
  oConnection.ConnectionString = oProvider
  oConnection.Open
  EndSub

  Another clue. If you check using DIAdem

  Microsoft Windows Script Debugger

  you are able to install the debugger in DIAdem.

  It would potentially have shown that the command does not work as expected.

  Sorry for the inconveniance

  Andreas

• I have a code 39 error on my TSST corp CD / DVD, TS-H652D (ATA) can not reload driver. best options please

  The player runs, but can't do anything. Thought on the use of the third party site was updated, but didn't know if it was legitimate. She noted 19 updates for my computer, but no mention of CD driver.

  craigdavis,

  Try...

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  or

  How trouble error Code 39 with CD-ROM or DVD drive in Windows XP/Vista

  Rick

• error 'Unable to write' 1x10001c30 address error message at shutdown began after you download Explorer 8 and then remove Explorer 8.

  "Write failed" error message during shutdown began after you download Explorer 8 and then remove Explorer 8. How can I get rid of him?

  Thank you, Matthew. I have eliminated the error message by reinstalling Explorer 8. I'll leave on my computer and the problem is solved.

• My DVD Player reads but does not write/copy (Satellite A60)

  I need help, I use a laptop Satellite A60 - 106 series
  and my dvd burner stop a write only copies 3% and stops. I use nero and roxio.
  Please help me.
  You can reply to [email protected]

  Hello

  Sorry, but I don't understand what you mean with adaptation? If you want to burn files to DVD media, it stops after about 3%. Am I wrong?

  Try to remove the drive from Device Manager, and then restart the device. After that the drive will be recognized and installed correctly. You can also try reinstalling the burning software.

• Error message when you use the DVD player

  I have a Satellite P200D and whenever I put a disc any in the drive I get an error NON-DISQUE when I eject the disc. I always make sure I close all programs relating to the use of the disc before you try to take out the drive. It is a new problem that I used the laptop for a few months with no problems at all. The text of the error message is below. Pointers would be appreciated. I can live with that, but it would be nice not to have to.

  Exception Processing Message 0xc0000013 0x764C023C 0x8E4A1B6C 0x764C023C 0x764C023C settings

  OK, if you try to exit the disc using the eject button on the side of the laptop, why not try ejection through windows software.

  To do this right-click on the dvd drive in my computer, then click "eject". This could mean windows that its ok to let the player go now.

  Another solution would be to save all the important data to another drive, and then put the laptop "out of area State" by using the recovery disk. I would say that the problem will disappear.

  However, if problems persist, please consult your place of purchase for a check up.

  Good luck.