IDM and PCI compliance
Hello, I have a 5510 ASA with and AIP - SSM installed. The question is, IDM will store the logs from the IPS module even when it is closed, or does it stay open? In addition, if either one loses power, are newspapers lost and they'll start back automatically? If this is not the case, how can I make this happen for purposes of PCI compliance?
Hello
The IDm will not store dressing room are events. You must enable external syslog are you can use Cisco IPS Manager Express (IME).
Feisal.
Tags: Cisco Security
Similar Questions
-
I install a new 5520 with IPS for a client, and they ask on the SSL (WebVPN) being self-signed PCI compliance. I don't know what document to find this information under the PCI DSS. There was also mention on double authentication required, but without seeing the actual needs, I guess just to her.
If anyone can point me in the right direction or explain the low down on what is needed to make SSL compatible PCI, I would be very grateful.
I am not aware of a pure and simple ban against self-signed certificates, but personally would prefer those to a root of trust CA - PKI company or third party. For me, it shows a greater awareness to safety.
PCI DSS 8.3 requirements requires two-factor authentication:
8.3 incorporate two-factor authentication for remote access (access level network from outside the network) to the network by employees, administrators, and third parties. (For example, remote authentication and remote service (RADIUS) with tokens, access controller access control system terminal access (GANYMEDE) with chips; or other technologies that facilitate two-factor authentication.)
Note: Two-factor authentication requires two of the three authentication methods (see 8.2 requirement for a description of the authentication methods) be used for authentication. Using a factor twice (for example, using two separate passwords) is not two-factor authentication.
You can configure an ASA with two factors schemens (RSA SecureID and LDAP etc.).
-
Anyone know where I can find something to confirm the PCi compliance at level 1 or 2 in British Colombia. It is assumimnung he. Cannot intergrate WorldPay without it.
Thank you
Hello
Please log a ticket case for more details on PCI with BC level for us details can help you with your query.
Admin-> help & support (to connect a ticket)
Kind regards
-Sidney
-
PCI Compliance Server 2012 IIS 6.2
I have a client that is running Server 2012 with IIS 6.2 and so far I've supported all the questions except two to make them compatible PCI.
Here are the two imminent failures.
Server is sensitive to the BEAST attack 443/tcp
STATE OF PCI COMPLIANCE
PCI severity: MEDIUM
IN CASE OF FAILURE
DETAILS OF THE VULNERABILITY
CVSSv2 Base Score: 4.3 (AV:N / AC:M / to the: N / reports / i: s/o: N)
Gravity: potential
Category: Browser Exploit against SSL TLS
CVE ID: CVE 2011-3389
Bugtraq ID: 49388 49778
OSVDB: 74829
References Microsoft: MS12-006
References of providers: CERT: TA12-010 has CERT - VN:VU #864643 HP: HPSBMU02900
UBUNTU:USN - 1263-1 SECTRACK:1026103 SECTRACK:1025997
SECTRACK:1029190 APPLICATION: 49778 SUBMISSION: 49388 REDHAT:RHSA - 2012:0006
REDHAT:RHSA - 2011:1384 MS: MS12 - 006-201406-32 GENTOO:GLSA------------------------------------------------------
osCommerce allows cross-site scripting 443/tcp
STATE OF PCI COMPLIANCE
PCI severity: MEDIUM
FAILURE of the XSS/SQL/SSL vulnerabilities are not compatible PCI
DETAILS OF THE VULNERABILITY
CVSSv2 Base Score: 4.3 (AV:N / AC:M / to the: N / c: n / I: P / A:N)
Severity: concern
Category: Cross site scripting
CVE ID: CVE-2003-1219
Bugtraq ID: 9238
OSVDB: -.
Microsoft references: -.
References of providers: QUOTE: 9238
Details: Cross-site scripting (XSS) vulnerability in the function tep_href_link in
for osCommerce before 2.2 - MS3 html_output.php allows remoteHello
Question about Windows Server 2012 are best addressed in the TechNet forums. Ask your questions here: https://social.technet.microsoft.com/Forums/windowsserver/en-US/home
-
HP Pavilion g4: HP has no Audion and PCI device driver
My phone has no audio. Need a driver for the device in PCI and PCI Simple Communications Controller. Can someone help me? Thank you very much...
My laptop is HP Pavilion g4 and Im using OS 64-bit of Windows 8.
You are the very welcome.
Here are links to the drivers you need...
Audio. Install and reboot the PC.
This package contains the driver that allows Audio IDT high definition (HD) in the notebook models that are running a supported operating system.
File name: sp59649.exe
PCI device:
This package contains the driver that allows the Realtek card reader in laptop models running a supported operating system. The card reader allows users to read or write to removable storage cards supported, which are typically used in digital cameras, digital music players and cell phones.
File name: sp58518.exe
PCI Simple Communications controller:
This package provides the driver Intel Management Engine Interface (MEI) for the notebook models and operating systems. The Intel Management Engine Interface allows communication between the host operating system and the Intel Management Engine firmware.
File name: sp58516.exe
-
HP15-ac042tu: Ethernet controller and PCI Simple controller drivers required
Installed the Ethernet and PCI Simple Communications Controller controller a certain number of times, but the error message in the device rest Manager again. Could someone please help me with the correct links for drivers for my laptop HP15-ac042tu.
Hello:
I'm glad you have the ethernet driver.
You need the driver for the wireless card that your laptop is.
You will also need this bluetooth driver...
http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_149898_1
-
HP DC7700p PCI SIMPLE COMMUNICATIONS CONTROLLER AND PCI SERIAL PORT
Hello
I have a HP DC7700p Office for work that is missing, PCI SIMPLE COMMUNICATIONS CONTROLLER AND PCI SERIAL PORT DRIVERS for WINDOWS XP PRO MISSING. CAN SOMEONE HELP ME TO DOWNLOAD THE DRIVERS. I ' M RUNNING WINDOWS XP PRO ON THIS MACHINE.
THANKS IN ADVANCE
SERIAL PORT PCI: PCI VEN_8086 & DEV_2997 & SUBSYS_2801103C & REV_02\3 & B1BFB68 & 0 & 1 B
PCI SIMPLE COMMUNICATIONS CONTROLLER: PCI VEN_8086 & DEV_2994 & SUBSYS_2801103C & REV_02\3 & B1BFB68 & 0 & 18
Hello:
Need the driver of the amt for devices...
-
Wireless, lan usb and pci is not installed
Hi, I just bought a new g001sx 15 HP and installed Windows 7 Professional 64 bit. After you install the operating system of my lan wireless, LAN, USB and PCI devices is not installed, I don't know what to do. installing drivers atheros already tried and it didn't work. I have already inserted an image that shows that some of my drivers are not detected. Thanks in advance.
Hello:
Here are links to the drivers you need...
First install the amd chipset drivers and reboot. You want the first file on the Web page.
This will install the smbus and usb 3 controllers.
http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064
Then, install the beta amd radeon catalyst graphics driver.
http://support.AMD.com/en-us/KB-articles/pages/latest-catalyst-Windows-Beta.aspx
If the amd chipset driver does not install the usb controllers as advertised 3 that he would, and then download and install these two...
Ethernet controller: DL and install the 2nd driver on the list.
PCI device: DL and install driver 1st on the list.
In order to provide me with the wireless driver which you are interested, please do the following...
Go to Device Manager and click on the network controller needing drivers.
Then click on the Details tab at the top of the control of the network window.
Now, you see a drop-down list of property and it is set by default to the Description of the unit.
Drop down on it and select the second item in the list (Hardware ID).
After the first string of characters that start with PCI\VEN.
-
Problems with the Ethernet controller and PCI Satellite L30-10 X device driver
HelloW!
Sorry for my bad English, I'm from the Russia.
A few days ago, I bought Satellite L30 - 10 X with W Vista on board. In my opinion, that this OS does ' t very good on this computer, so I install W XP.I have some problems with drivers. At first, I don't know which model I have: PSL30 or PSL33? I have download all the drivers for the two models. But after installation, computer doen't find the drivers for the Ethernet controller and PCI device...
Hello
Satellite L30-10 X belongs to the series of PSL33E. This number located on the label on the bottom of the device!
You must choose this number in the form of driver download for XP compatible drivers.
I put t know why you are not able to install the LAN driver. I have the same laptop with Vista and I've install the XP and all the drivers will work perfectly.I assume that you have installed the drivers in the wrong order. Please take look in the Toshiba installation instructions txt file. In this order, install the driver! This is important.
I think that you should install XP again to ensure that the registry clean, then download and install the XP drivers compatible as mentioned in the installation instructions file.
Good luck
-
dc7800mt: dc7800 10 Windows 64 b PCI Simple Communications and PCI Serial Port drivers missing
Can't seem to find the drivers for a dc7800 upgraded to Windows 10 64 b for PCI Simple Communications Controller and PCI Serial Port devices. Any help would be greatly appreciated. Paul_Tikkanen, are you still there?
Hello:
Yes, I'm still here, and Yes, I know what drivers you need...
You need this for the PCI of Simple Communications controller:
This package contains the device driver Intel Active Client Manager Host Embedded Controller Interface (HECI) for desktop models and operating systems supported.
FTP://ftp.HP.com/pub/SoftPaq/sp46001-46500/sp46137.exe
PCI serial port:
This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.
FTP://ftp.HP.com/pub/SoftPaq/sp46001-46500/sp46134.exe
And let me give you a bonus tip... Install the audio driver Soundmax ADI W7.
I found that works much better than W10 installed.
You install it, then select multistreaming in adi Control Panel, restart again and go to manage audio devices in the Control Panel, and then select the PC speakers, but of course install the W7 audio driver is optional, and it is up to you...
-
Photon counting using Photon unique cash Module and PCI-6602
Hi all
I am currently working on program couting of photons using a single (Excelitas) and PCI-6602 photon counting module connected to the BNC-2121.
I took a glance at other positions, but I still couldn't solve my problem (or, again, I'm not sure if yes or no, the problem is the specification of the material).
In the program, I'm generates a trigger to 1 MHz pulse using a trigger in a separate loop.
Other than that, I have loops of the producer-consumer model to get data and do a simple subtraction to calculate the number of photons in 1 microsecond.
According to the values connected to 'Input.BufSize' of buffer DAQmx and "Samples per channel" DAQmx calendar, I could change the loop number that the program has done its job correctly.
With the values, the program acquires photon 1 MHz with signls for 139 times.
After that, the program stops and the loopback number increases very quickly.
When I forcifully took stop the program, while the loop number increases very quickly, the program appears "error-200141".»
The error that says "data has been replaced before it can be read by the system." Mechanism of data transfer is interrupted, try to use DMA or USB in bulk. Otherwise, divide the input signal before taking the action. "even if the meter explicitly works in DMA mode by using the sample clock.
I wonder there is nothing that can solve my problem or even the only solution will buy a better Board of counters/timers.
Thank you all for reading this.
I will be very happy with any index
Kind regards
Myeongsu
Yes, the same thing happens on my system.
It does not happen with PCIe-6612.
I found more strange things:
When I start to reduce the frequency at a time given (800kHz) can fill the buffer, it will not start since the beginning of the buffer. He can go to the beginning of the buffer only at 100 kHz for my PC.
Options to fix:
(1) PCIe-6612. Seems to work. I tried streaming at 10 MHz, 5 min - fine.
(2) reduce the frequency of the pulse. If your laser supports 100 kHz, you're fine.
(3) put in place additional synchronous counter at 100 kHz. Basically, it's material average number of photons by 10 pulses.
(4) read 2 adjacent pulses each 1/50 kHz - then your data transfer will be 100 kHz and you will get the number of photons of this impulse of the 20 - th.
Programming issues:
(1) remove the display of the received picture, make only the processing of data and show results if you really need it.
(2) clock.vi sample sets the buffer size, if you specify the size of the buffer, do this after this vi.
(3) I deleted unnecessary "loop generation." He is running on the hardware and stops when you stop it - after reading the loop ends.
-
Serial port PCI and PCI Simple Communications Controller
Hello!
My computer OS is Windows 8.1.
I just shearch something and I found that... I don't have serial Port PCI and PCI Simple Communications Controller. (Unintalled)
Serial port PCI-> VEN_8086 & DEV_29B7 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 1 b
Controller PCI Simple Communications-> VEN_8086 & DEV_29B4 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 18
Sorry for my English. But can anyone help me?, where I can download these files.
Hello:
Here are links to the drivers you need...
Install PCI Simple controller Comms
Install PCI Serial Port:
-
Looking for a driver for a HP 250 G3 laptop
Device PCI and PCI Simple Communications controller drivers
OS: Windows 7 Home Premium (64-bit)
Impossible IM find thank you for giving the link.
Thanks in advance
Hello:
When the G3 250 support site returns to the top...
You need these drivers for devices...
Realtek card reader driver (under the section storage drivers)
Driver Intel Management Engine Interface (under section chipset)
-
lack of pci bus 2 and PCI/VEN_10EC & DEV_5209 & SUBSYS_3577 103C & REV. Can someone please help me and tell me how to find these drivers downloaded to my pc. ID enjoy really enjoy it and thanks in advance...
Hello
It's the card reader. Please try first for Windows:
Kind regards.
-
Drivers wireless and PCI Simple Communications HP 2000-2d00SM controller
Hello, I need drivers for Hp 2000-2d00SM laptop for the wireless and PCI of Simple Communications controller.
Network controller
PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C & REV_01
PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C
PCI\VEN_168C & DEV_0036 & CC_028000
PCI\VEN_168C & DEV_0036 & CC_0280Simple PCI communications controller
PCI\VEN_8086 & DEV_1E3A & SUBSYS_1854103C & REV_04
PCI\VEN_8086 & DEV_1E3A & SUBSYS_1854103C
PCI\VEN_8086 & DEV_1E3A & CC_078000
PCI\VEN_8086 & DEV_1E3A & CC_0780Tnanks in advance
Hello:
You need these drivers if you have installed W7...
Wireless:
Comms Simple PCI:
I see that you posted earlier and for anything else you need, you can use all the W7 drivers and the software of the model I posted the driver Intel Management Engine Interface, with the exception of the BIOS and firmware files.
Maybe you are looking for
-
How can I go forward/backward more than 1 page at a time
Previously, I was able to go backward/forward several windows at a time using the icons and next to the back and forward arrows. There was very very useful... too many clicks cause carpal.
-
change my mp3 music does, nt come out as I thought and I so do CD fashion old way and burn.when I have made a set of mp3 music library, they were all dated 06/01/16. now I want to know if there is an easier way to get rid of all the mp3 songs to the
-
Next version of the iPhone can put the Nepali language
Next version of the iPhone can put the language Nepali kybo
-
How can I get the Smart Print button to appear in IE9?
I run the 32-bit version of IE9 in Windows7 Ultimate 64-bit. I have version 1.0.9.0 HP Smart printing (I appears in "Programs and features".) I went to the website of seb and ran the activation and he succeeded. The HP bing toolbar appears, but none
-
WRE54G is dead...
It worked well until last Saturday when the Red of Nonconnectivity light flickered. Not much, it's happened before, so I just unplugged it, plugged in again and everything was happy. Sunday Nonconnectivity red light was back on the SOLID. I was in