ie11 fails to load the flash

Similar Questions

• Flash 22.0 failed to load the Flash games.

  Hi, I have questions that there is no progress in the process of loading in Flash games. Examples of this game are: bad eggs online, everyone publishes, traumatic psychosis Live, etc.

  I just fixed my problem. I refreshed Firefox. Thank you very much for your help!

• 2811 - problem with the «failed to load the flash» start

  Hello community,

  I have some problems to use my router from cisco c2811. After accidentley delete flash: / .bin file, my IOS is no longer available. That is why, after a reboot, the router is in a continuous loop with boot: cannot fload 'flash'

  Y at - it any possibiliy to set up the device with the new IOS, which could be installed from usbflash1: for example

  I can't enter break (CTRL + BREAK to the secure CRT) sequence.

  Error code:

  Upgrade ROMMON initialized
  PASSWORD RECOVERY FEATURE IS DISABLED
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  loadprog: incorrect file magic number: 0x0
  startup: unable to load "flash:
  C2811 platform of 262144 KB of main memory
  Main memory is configured for 64-bit with ECC active

  Upgrade ROMMON initialized
  PASSWORD RECOVERY FEATURE IS DISABLED
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  loadprog: incorrect file magic number: 0x0
  startup: unable to load "flash:
  C2811 platform of 262144 KB of main memory
  Main memory is configured for 64-bit with ECC active

  Upgrade ROMMON initialized
  PASSWORD RECOVERY FEATURE IS DISABLED
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  loadprog: incorrect file magic number: 0x0
  startup: unable to load "flash:
  C2811 platform of 262144 KB of main memory
  Main memory is configured for 64-bit with ECC active

  Upgrade ROMMON initialized
  PASSWORD RECOVERY FEATURE IS DISABLED
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  loadprog: incorrect file magic number: 0x0
  startup: unable to load "flash:
  C2811 platform of 262144 KB of main memory
  Main memory is configured for 64-bit with ECC active

  Y at - it any possibiliy to set up the device with the new IOS, which could be installed from usbflash1: for example

  To get the G1 SERP to start an IOS (from ROMmon) using the USB, the ROMmon himself must firstly upgraded.

  Then, is there a compact flash currently in the slot?  If so, eject the CF and copy the IOS in CF using a multicard reader.

• Failed to load the Flash 10.1

  Run the installation program, and he said he completed 100%. Then a window appears and says "can not install because an existing version can stil '.

  l in use. Close all applications using Flas Player and try again." I don't have any applications open, so do not know what it takes to close. I uninstalled previous versions of Flash Player, set the security settings of IE8 in the middle and done all the other things suggested. Any ideas?

  It seems that Shockwave Flash Object has loaded. It is activated and the version number is 10.1.102.64

  As an aside, it should not be this hard load a piece of free software!

  Hey, good for you. I think you just need a better procedure to use. That's what I use, if I have to manually install.

  I'd appreciate if you mark your thread as answered.

  Thanks for posting back :-)

  eidnolb

• Firefox does not load the flash of the Firefox home page

  Firefox does not load the flash of the Firefox home page

  It's not Flash, but a film WebM.

  <video xmlns="http://www.w3.org/1999/xhtml" poster="data:image/png;base64,<base64 data>" src="https://snippets.cdn.mozilla.net/media/files/e29ada39-11f4-4157-ae1c-1340d9455692.webm"></video>

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem.

  • Put yourself in the DEFAULT theme: Firefox/tools > Modules > appearance
  • Do NOT click on the reset button on the startup window Mode safe
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• problem in loading the flash through activex container files

  I'm trying to access flash files using activex container.i chose property shockwave flash movie to load the flash file.but when filw path is specified for this property it has extension "FLA".

  After the execution of the VI, I am unable to see the animation.

  I also changed the extension ".swf" but still do not get the image animated after the execution of the vi...

  There is no error as vi can be in operation

  can someone help me to find out why the flash file is not load...

  Hi shruti G,.

  To stop the animation at the end of the use of the program STOP PLAYING call of node. Try this and tell me. Always try to search options.

  Good luck

• What should I do when I receive the message 'unable to load the flash shockwave.

  What should I do when I receive the message 'unable to load the flash shockwave.

  Hello

   
  1. how many times you get this error message? This problem is limited to specific Web pages?

  2. Once you get this error message? What is your default browser?

  
  Find out what version of Internet Explorer you are using
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-out-which-version-of-Internet-Explorer-youre-using
  
  3. have you installed new hardware or software before the show?

  4. What is the operating system installed on the computer?

   
  5. are you logged in as administrator?
   
  
  Method 1:
  If you are facing problems with Internet Explorer 9, I suggest you read the article and try to run theFix it:
  Troubleshoot Internet Explorer to IE quick, safe and stable
  http://support.Microsoft.com/GP/pc_ie_start
  Note: Note that the reset Internet Explorer (IE) resets all settings defined by the user, including those established by the installed extensions, toolbars and other add-ons for IE by default. This includes all the security, privacy and settings area. Also this will erase browsing history, delete all temporary Internet, cookies, form data files and especially all the passwords.
   
  Method 2:
   
  a. search for Internet Explorer in the start menu.
   
  b. right click and select "Run as Administrator".
   
  Check if the problem occurs.
   
   
  Method 3: Uninstall and reinstall Adobe Shockwave
   
  To uninstall a program
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program
   
  
  I also suggest you to download and install the latest version of Adobe Shockwave player and check if that helps:
  
  http://get.Adobe.com/Shockwave/
  Provide more information about the issue so that we can better help you.
   
  I hope this helps.

• Half-life 2 says failed to load the Launcher DLL specified module could not be found

  Failed to load the Launcher DLL:

  the specified module could not be found

  Hi Madoo17,

  Welcome to the community of Microsoft and thanks for posting the question. I've surely you will help find a solution on the issue.

  1. Once you get this error message?

  2. it worked before?

  3 did you changes to the computer before the show?

  Perform the steps:

  Method 1:

  Put the computer in a State of boot is a way to know which application is causing this problem.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Step 1:

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  Follow the steps in the link below to do the same thing:

  How to configure Windows XP to start in a "clean boot" State

  Note: After troubleshooting, be sure to set the computer to start as usual as shown here:

  Step 2: To configure Windows to use a Normal startup state

  After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  a. Click Start and then click Run.

  b. type msconfig and click OK. The System Configuration Utility dialog box appears.

  c. click on the general tab, click Normal Startup - load all services and device drivers and then click OK.

  d. When you are prompted, click on restart to restart the computer.

  Method 2: Use the (SFC) System File Checker tool.

  SFC system gives an administrator the ability to scan the files all protected to check their versions. If the System File Checker detects that a protected file has been replaced, it retrieves the correct version of the file in the folder cache (% Systemroot%\System32\Dllcache) or the Windows installation source files and then replaces the incorrect file. System File Checker verifies and repopulates the cache folder also. You must be logged in as an administrator or as a member of the Administrators group to run the System File Checker.

  Check out this link to do the same thing:

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  Hope this information helps. Please reply back with the State so that we can help you.

• Failed to load the local profile. IO error. All files in My Documents have disappeared. How to restore

  did a normal turn on the computer.  Message came back failed to load the local profile.  IO error.  When he signed me, all my documents in My Documents had disappeared.

  A corrupt profile is fairly easy to recover with minimal losses.  Refer to the following procedure:

  "How to recover damaged Windows XP user profile"
    <>http://support.Microsoft.com/kb/555473 >

  Corrupt profiles are almost always accompanied by hard drive corruption.  After recovery, scan your hard disk for errors using chkdsk with the /f or/r option

  "How to perform disk error in Windows XP check"
    <>http://support.Microsoft.com/kb/315265 >

  The disk check procedure can take hours depending on the size of your hard drive and the amount of corruption and cannot be interrupted, then run it when you won't need your computer for awhile.

  HTH,
  JW

• start the computer to start but stops at "failed to load the core file?

  Original title: how to get Windows XP to boot my computer from starting when starts but stops at "failed to load the core file?

  When I try to start my computer, it stops at "cannot load the kernel."  It will go no further. What is the solution?

  Please see: How to perform a Windows XP repair install

• the user profile Service service has no logon failed to load the user profile

  I received the following message when I try and log in my account to have:

  The user profile Service service has no logon failed to load the user profile

  What are my options?

  Hello

  1st thing to try is the system in safe mode restore to before the problem

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not solve it read more

  read the tutorial below

  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  When you log on a Windows Vista-based or a Windows 7 computer by using a temporary profile, you receive the following error message:

  The user profile Service has not logon. User profile cannot be loaded.

  http://support.Microsoft.com/kb/947215#letmefixit

  Your user profile was not loaded correctly! You have been logged on with a temporary profile.

  http://support.Microsoft.com/kb/947242

  If you tried to log on to Windows and received an error message telling you that your user profile is damaged, you can try to fix it. You will need to create a new profile and then copy the files from the existing to the new profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• "When I tried to sign on the computer, I get the following message: the user profile service service failed connection, failed to load the user profile.

  "Whenever I tried to sign up with my password to connect, do the following: the user profile service service failed connection, failed to load the user profile" when I click OK, it disconnects... Help, please

  Go to Safe Mode and do a system restore. See the link below:

  The user profile Service has not logon. User profile cannot be loaded
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/the-user-profile-service-failed-the-logon-user/995955f8-d9d4-4148-840D-c896c3be78b8

  Follow the links on the post.

• Failed to load the user profile on my laptop. Help

  I can't connect my laptop as his watch the above message, it is 2 years and a half old and isa an inspiron 1525, helps, I know I need to re boot, but as I am not too good with the system and was looking to find out where to download a disc and make sure that I get the right one can someone help me. in my library now wiyh a ubs if I need.

  Next time please post the error message in its entirety... verbatim.

  What is the real error message?...

  Failed to load the user profile and the user profile service does not log

  If Yes, read on...

  You haveanother admin account , you can connect?
  If so, please do and do a system restore, if no help, run the Microsoft Support tutorial below.

  If you don't have another admin account, go into safe mode.
  Here's how to get safe mode:
  Shut down your computer > turn it back on and immediately and repeatedly tab key F8 until you see a black and white screen. The top/down arrow and select Safe Mode with network.

  In the window of logon in safe mode...
  1 can connect to your account administrator in safe mode?
  If so, do a restore system first, if no help, run theMicrosoft tutorial support listed below.

  2. If you can't log into your own account, you see another admin next to your account in the logon screen?
  If you do, that one is the built-in Administrator account. By default, there is no password. Connect to it and newdo a first system restore, if not help, run the Microsoft tutorial support listed below.

  If you are able to log on in safe mode, do a system restore. Choose a date when you were able to log in NORMAL MODE as your restore point.
  How to restore the system:
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  Tutorial from Microsoft support :
  http://support.Microsoft.com/kb/947215
  There are several methods, go through one by one.
  Method 3 has a "fix it for me" application

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Log: error message: "the service user profile service has no logon failed to load the user profile.

  Error message: "the service user profile service has no logon failed to load the user profile.

  Unable to connect.

  ·                        Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  ·                        http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  See if the information in the above tutorial will help you.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/947215#letmefixit

  Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/947242

  A temporary profile is loaded after you connect to a Windows Vista-based system

  See you soon.

  Mick Murphy - Microsoft partner

• I also, I get the error "the service user profile Service has no connection, failed to load the user profile" but I have not been able to correct the problem by following the listed solutions.

  I got the error "the service user profile Service has no connection, failed to load the user profile" when you try to use my desktip.  It is on the login page.  My account icon loads and the guest account. I have enter my password as an administrator and get the error message listed above. I followed all the solutions I could find and it is not corrected.

  I have a slight hitch, after several failed here, I checked the domestic Group on my laptop and I have high listed as connected to the Group Home Office; with all the files.  How can I fix the desk top to coinside with his status of being online.  Yet once, my counter top will not recognize the password, but the desk top shows online in the home group.

  Home Group is Windows 7.

  Here is the Vista Forums.

  What operating system do you use?

  Vista info below:

  ·                        Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  ·                        http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  See if the information in the above tutorial will help you.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/947242

  A temporary profile is loaded after you connect to a Windows Vista-based system

  See you soon.

  Mick Murphy - Microsoft partner