IKEv1 and IKEv2 session in ASDM monitor?

Similar Questions

• IKEv1 and IKEv2

  I have a router 2821 with multiple IPSec Tunnels on it.  I would like to replace it with an ASA 5510.  My hope is to share these stars with a minimal impact on the active Tunnels.  I have the details of each well-documented Tunnel.  My question or concern is in the configuration of Tunnels on the SAA.  I have to configure IKE proposals in IKEv1 right?  If I use IKEv2, my concern is that there will be compatibility problems with the remote end of the tunnel, or is functional IKEv2 with IKEv1?  If no, then, can I just all set up in IKEv1 and ignore IKEv2?

  Thank you in advance for any idea offered.

  Dear Eric,

  Both ends must be configured for the same version of IKE.

  So you can ignore the IKEv2 parameters, even to uncheck the option 'Enable' IKEv2 in the connection profile.

  HTH.

  Portu.

  Please note all useful posts

• AnyConnect + possible PSK (pre-shared key) as under with cisco vpn client ikev1 and ikev2

  Is it possible to create a VPN Anyconnect of RA with just the name of user and password + pre-shared key (Group) for the connection, as could do for ikev1 with cisco VPN client? I am running 8.4.X ASA code and looks like tunnel-group commands have 8.2.X somewhat change. If you change the group type of the tunnel for remote access, now there is no option for IKEv2 PSK. This is only available when you choose the type

  Type of TG_TEST FW1 (config) # tunnel - group?

  set up the mode commands/options:
  Site IPSec IPSec-l2l group
  Remote access using IPSec-IPSec-ra (DEPRECATED) group
  remote access remote access (IPSec and WebVPN) group
  WebVPN WebVPN Group (DEPRECATED)

  FW1(config-tunnel-General) # tunnel - group TG_TEST ipsec-attributes
  FW1(config-tunnel-IPSec) #?

  configuration of the tunnel-group commands:
  any required authorization request users to allow successfully in order to
  Connect (DEPRECATED)
  Allow chain issuing of the certificate
  output attribute tunnel-group IPSec configuration
  mode
  help help for group orders of tunnel configuration
  IKEv1 configure IKEv1
  ISAKMP policy configure ISAKMP
  not to remove a pair of attribute value
  by the peer-id-validate Validate identity of the peer using the peer
  certificate
  negotiation to Enable password update in RADIUS RADIUS with expiry
  authentication (DEPRECATED)

  FW1(config-tunnel-IPSec) # ikev1?

  the tunnel-group-ipsec mode commands/options:
  pre-shared key associate a key shared in advance with the connection policy

  I'm getting old so I hope that it is not in another complaint curmudgeonly on the loss of functionality. :)

  Many small businesses do not want to invest in the PKI. It is usually a pain to deploy, backup, make redundant, etc..

  But it would be nice to have a bit more security on VPN other than just the connections of username and password.

  If this is not possible, it is possible to configure the Anyconnect customer to IKEv1 with PSK and name at the level of the Group client?

  If this is not possible, WTH did cisco end customer VPN cisco as a choice of VPN connection (other than to get more fresh mail of license)?

  I really hope that something like this exists still!

  THX,

  WR

  You are welcome

  In addition to two factors, you can also do double authentication (ie the two using the user name and password). Each set of credentials can come from a Bank of different identities.

  With this scheme, you can can configure a local user name (common) with password on the SAA (think of it as your analog PSK) and the other be the AD user identification information.

• CSCux42019 - Cisco ASA IKEv1 and IKEv2 buffer overrun vulnerability

  Hello

  WE have a CISCO ASA 5520 with firmware 8.4.7 - 15 and let me know if this device/firmware is affected by this new vulnerability ' ASA IKEv1/IKEv2 - Buffer Overflow Vulnerability '.

  Thank you very much

  Hi Jesus,

  Yes, it is affected.

  Please upgrade the recommended patches.

  Since it is set at 8.4.7.30 you can try upgrading to this image.

  Kind regards

  Aditya

• CSCux29978 - Cisco ASA IKEv1 and IKEv2 buffer overrun vulnerability - 1

  Hello

  im confused. In the Advisory secruity on this bug https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/ci...

  He said not "affected" in the line of the main version of ASA 9.1. 9.1 is so affected by this bug and we need to upgrade to 9.1. (7) or not?

  regarding

  Christian

  Hi Christian,

  According to the chart, the only version not affected is code 8.5 9.1 code, you must update to 9.1.7 to be safe from this vulnerability.

  Cisco ASA Major Release	First version fixed
  7.21	Affected; migrate to 9.1 (7) or later version
  8.21	Affected; migrate to 9.1 (7) or later version
  8.31	Affected; migrate to 9.1 (7) or later version
  8.4	8.4 (7.30)
  8.51	Not affected
  8.61	Affected; migrate to 9.1 (7) or later version
  8.7	8.7 (1.18)
  9.0	9.0 (4.38)
  9.1	9.1 (7)
  9.2	9.2 (4.5)
  9.3	9.3 (3.7)
  9.4	9.4 (2.4)
  9.5	9.5 (2.2)

  It may be useful

  -Randy-

• Help his Mac Mini? Connected to monitor w / sound coming from monitor. I tried speaker external buffering in the back of the unit and still get only his monitor speakers.

  Help his Mac Mini? Connected to monitor w / sound coming from monitor. I tried speaker external buffering in the back of the unit and still get only his monitor speakers.

  How is the monitor connected?

  Are to connect the speakers to the headphone 3.5 mm? And not the line-in jack 3.5?

  If you go to System Preferences > sound > you can select the speakers/headphones output?

• I connected a VGA cable and clicked on the option monitor, he did not come on my t v

  VGA?

  I connected a VGA cable and clicked on the option monitor, he did not come on my t, v and the screen is black when I plug cable in the future. How can I get the possibility to save change?

  Perhaps the following links will propose a few ideas:

  How to connect my computer to a TV
  http://hookpctotv.com/

  How to connect your PC to your TV
  http://en.kioskea.NET/FAQ/Sujet-228-how-to-connect-your-PC-to-your-TV-set

  PC to TV cables and adapters
  http://www.SVIDEO.com/PC2TV.html

  Windows Vista-
  Connect your computer to a TV
  http://Windows.Microsoft.com/en-us/Windows-Vista/connect-your-computer-to-a-TV

  Windows Vista-
  HDTV: Frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/HDTV-frequently-asked-questions

  Windows Vista-
  From PC to TV, part 1
  Digital media stream to any room with Windows Media Center and Xbox 360
  http://Windows.Microsoft.com/en-us/Windows-Vista/from-PC-to-TV-part-1-stream-digital-media-to-any-room-with-Windows-Media-Center-and-an-Xbox-360

• Two monitors can be connected and function as a double monitors?

  Original title:

  Two monitors

  I have a Dell E2211Hb monitor and a Dell E176FPc monitor. Can they somehow be connected and work as a double monitor?

  If you have a videocard head double, Yes. Look at the back of your PC. Most new computers have a video port VGA and DMI.

  Connect each monitor using the appropriate wiring. Restart Windows, right click on a clear part of the desktop display and select Properties.

  Setting up dual monitors...

  http://www.Dummies.com/how-to/content/how-to-set-up-multiple-monitors-with-Windows-7.html

• How to find the lock and kill session in order to release it?

  Hi all

  EBS R12.2

  "I met ' could not book record" in our case. How to release the session locked?

  I usually do this by bouncing the apps & db level. Is their subtle way?

  
  

  
  

  

  
  

  
  

  Kind regards

  JC
  

  
  

  
  

  Ideally, you should check for locks on the table in question where records are trying to access.

  AFAIK, you must check the v$ locked_object and find sessions.

  Hope this helps!

  Kind regards

  Hugues

• How can I keep the laptop and find only the external monitor when I close the lid?

  Original title: external monitor

  I want to use an external monitor with my laptop Vaio Windows 8, but when I close the lid, both screens will disappear.  How to keep your computer on and display only the extgernal monitor when I close the lid?

  I want to use an external monitor with my laptop Vaio Windows 8, but when I close the lid, both screens will disappear.  How to keep your computer on and display only the extgernal monitor when I close the lid?

  Hello

  Perform the following steps.

  1. press the Windows key + X to display the System menu.

  2. Select Control Panel.

  3. Select the Power Options.

  4. in the left menu, select Choose closing the cover .

  5. look in the section of power and sleep buttons and lid settings .

  6. use the drop-down menus of the section when I close the lid , and then select do nothing for both options.

  I hope this helps.

  Concerning

• How to configure the agent to monitor performance only the vcenter vmware and esx, not need to monitor virtual machines

  How to configure the agent to monitor performance only the vcenter vmware and esx, not need to monitor virtual machines

  This is not possible with the way in which we collect information.

• What are the differences between pga memory max session and pga session in memory?

  Hi all

  What are the differences between pga memory max session and pga session in memory?

  SELECT s.sid, n.name, s.value FROM v$ sesstat s, v$ statname n

  WHERE s.statistic # = n.statistic #.

  AND n.name = 'pga session in memory. "

  SELECT s.sid, n.name, s.value FROM v$ sesstat s, v$ statname n

  WHERE s.statistic # = n.statistic #.

  AND n.name = 'pga memory max session ";

  
  

  
  

  Note that I have read the documentation. However, it is not clearly explained.

  
  

  Thank you
  

  John Stegeman wrote:

  I agree with the comments of the Ed, NightWing.

  You do not have a story to ask questions that are clearly answered in the documentation.

  Mind your own business. If you answer the question, so answer! Otherwise, please stop the thread engrossing.

• Develop Module and the wide range of monitors

  Is the develop module drive different display of the other modules (library, Print, etc.)?

  I ask because I see different, richer and more saturated colors to develop, and a Google search turns up any complaints about this problem, which dates back to 2007.

  I have a Dell UP2516D monitor calibrated with an i1DisplayPro software and i1Profiler XRite.  This monitor is capable of 99% AdobeRGB.

  Having read the other threads on this topic, I checked the following:

  • The monitor is correctly calibrated
  • I have disabled the option of processor use chart
  • The ICC profile is version 2, not version 4

  It's worrying because during the export, the JPEG format resulting looks desaturated images, I see in the library, not the end result of my editing module in the develop module.  Here is a pair of screenshots.  In both cases, the small window is the exported image (JPEG) displayed in the Windows Photo Viewer. The largest window is a partial screenshot of Lightroom.  The screenshot was made by opening the JPEG and then exported by moving the Windows Photo Viewer on the top of the window of Lightroom.

  The first image shows the difference between JPEG format and what is seen in developing

  

  The second image shows the fact that the exported JPEG resembles what we see in the library view.

  

  The develop module is fundamentally different in how it sends image data to the screen?  Might it interact with the features of a Monitor wide gamut of cause this problem?

  Even if the answer is Yes, it does not explain why the effect is present even in the screenshots.  Take a screen capture, encode in PNG and then display in the Viewer Windows photo or other non-Lightroom software should eliminate special effects due to LR. The difference is always present in the screenshots, even when displayed on screens less capable, so there must be a problem of mismatch of actual color here.

  Yes, there is a difference, read here: in Lightroom color management

  I don't know, is the windows photo viewer color managed?

  If you are using a large monitor range, you can display the correct colors with an application that is color management. Otherwise, you will still see a shift/colorshift.

• Difference between V$ SESSION and GV$ SESSION

  Hi all
  
  I have a few questions:
  
  1. What is the difference between V$ SESSION and GV$ SESSION?
  
  2. is there an Oracle function defined as USERENV('SESSIONID'). to get the AUDSID of GV$ SESSION?
  
  Thanks in advance

  Hmmm... I had no idea... so I did some digging.

  The short answer is that other than the SYSDBA and SYSOPER, connections that all get the same AUDSID, it is unique throughout the database. The AUDSID values are generated from the SYS. Sequence of $ AUDSES.

  See MetaLink doc. ID 123128.1 and 122230.1 for more information.

  -Mark

• How to display the user id and the session on the form?

  Hi all can someone guide me how to display the user id and the session on the form? Please guide me
  
  Sarah

  Hi Sarah,.

  You can use GET_APPLICATION_PROPERTY (CONNECT_STRING) for this.

  BTW, have you tried search in forms online help? It has good examples explaining all the built-ins.

  Arun-