Information about TelNet and SSH

Similar Questions

• WAP561 To Telnet and SSH

  Hello

  We have two WAP561 devices and they delivered with firmware 1.0.3.4. In this firmware release notes, there is open opposition with reference number CSCty22825, declaring that telnet and ssh is disabled in the interface chart and SNMP. In the notes of the other releases, as 1.1.0.4, this caveat is no longer present. We have improved our 1.1.0.4 devices, over telnet and ssh section is still not present in the GUI.

  Is there a way to enable ssh on these devices? In the administration guide, there should be a section called 'Telnet and SSH', but it is not present in the GUI. We also checked with the emulators with different firmwares. Still no telnet and ssh, section.

  Your help is very appreciated.

  Thank you

  Hello

  These options were available in a very old firmware (the first version) which is no longer present on the cisco.com site and unfortunately I do not have. For security reasons, these options have been removed the new firmwares available.

  I hope that the information provided was useful.

  If you have any other questions do not hesitate to contact me.

  Best regards

• Telnet and SSH

  Is it possible to have a different public IP (i.e. 66.102.7.000) address to telnet and SSH for the ASA 5510 remotely?  If it is possible, how you would install the telnet and SSH?  The config is attached.  Thank you.

  Laura

  laurabolda wrote:
  Thanks for your prompt response, Jon.
  For clarification, if my computer IP address is 66.102.7.10, can I SSH to the ASA (outside interface 109.66.25.80)? If I can, how would you set it up on the ASA?  Is it the same command as your previous response?
  Thanks.
  Laura
  

  Yes Laura he would be-

  SSH outside 66.102.7.10 255.255.255.255

  Jon

• Telnet and SSH on PIX515E does not

  I have two PIX515E (primary and Fail-over) and I can't access it via telnet or SSH.

  I can access only once they have restarted and then they react to me and close the connection.

  the version of the show from the primary is as below:

  Cisco PIX Security Appliance Software Version 8.0 (3)

  Version 6.1 Device Manager (1)

  Updated Wednesday 6 November 07 19:50 by manufacturers

  System image file is "flash: / pix803.bin.

  The configuration file to the startup was "startup-config '.

  Primary up to 3 days 19 hours

  up to 13 hours and 18 minutes failover cluster

  Material: PIX-515E, 128 MB RAM, Pentium II 433 MHz processor

  Flash E28F128J3 @ 0xfff00000, 16 MB

  BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

  Hardware encryption device: VAC + (Crypto5823 revision 0 x 1)

  0: Ext: Ethernet0: the address is 0019.e762.f577, irq 10

  1: Ext: Ethernet1: the address is 0019.e762.f578, irq 11

  The devices allowed for this platform:

  The maximum physical Interfaces: 6

  VLAN maximum: 25

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  VPN peers: unlimited

  This platform includes an unrestricted license (UR).

  Serial number: 810417710

  Activation key running: 0x7785a916 0x349cafef 0x49afea88 0x8bbd3f92

  Modified configuration of enable_15 to 12:49:25.499 EEDT Sunday, July 26, 2009

  can someone help me solve this problem please.

  I would upgrade to 8.2. I don't have the bug number, but you should be able to find it in the Bug Toolkit.

• Issue of Telnet and SSH on Cisco 3750.

  I turn on Cisco 3750 and everything so I wasn't able to connect in the area. I even changed the source interface and update transport under the VTY lines input method, no luck.

  Can I choose to disable SSH by removing the corresponding lines of configs and RSA keys. And I changed the entry to transport back to Telnet. After the reboot of the switch, I'm still not able to connect despite the fact that the box is accessible.

  Any help?

  Thank you

  Jean-Marie

  Hello

  This should help to confirm the configuration and troubleshooting SSH on your device: -.

  http://www.Cisco.com/c/en/us/support/docs/security-VPN/Secure-Shell-SSH/4145-SSH.html

  I hope this helps.
  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Information about Shockwave and Adobe Acrobat subscription wanted

  Separated from this thread.

  What is Shockwave for?  Is Adobe Acrobat subscription at $89 or $90 worth having to convert files to PDF format?  What is the only software that does this?  There must be an Open Source software which can do this, isn't there?

  Uhm - shockwave and PDF - related only by the parent company, really.

  https://www.Google.com/#q=what+is+Adobe+Shockwave+Player

  "Shockwave Player is the web standard for powerful multimedia playback. The Shockwave Player allows you to view interactive web content like games, presentations to business, entertainment, and advertisements from your web browser. The Shockwave Playerdisplays web content created with Adobe Director. »

  Read your other post for more information on the stuff PDF (why this post has divided?) ...

• Information about HP and HP EventHandler Planner

  Hello

  I use a Mac with the Lion of the mountains (10.8.4) and I see that my connection Scheduler HP and HP EventHandler objects.

  I did some research but couldn't know exactly what they are doing.

  If anyone has any information, I would really appreciate it.

  I try to stimulate the process of starting my mac and I wonder if these two elements are indeed essential our could be deleted.

  Thank you.

  PS: I use a HP OfficeJet all in a J3680.

  I couldn't find everything related to specific files, but as of last version of the software had similare process designed to determine the priorities and the order of queue. This means that when you send several jobs or have several requests sent to the machine it is able to treat them appropriately. They shouldn't take up much of your processing power and I wouldn't recommend disabling.

  I would like to know if this is the information you are looking for and I will get back to you as soon as I can!

  -Spencer

  PS have a wonderful day and a fantastic weekend!

• Is - this "you must buy one at a time or all requests to get those I want?" Impossible to find any information about it and can't contact Adobe. No more hotline number.

  Sorry but I need help I can't find anywhere, I keep asking on the Adobe web site.

  What I have to, but all iCloud applications just to get what I had in CS6?

  What do you have in CS6?

  Clouds plans come in two main flavors: full or simple App.

  If you need only 1 or 2 apps and 2 x plans unique App are the cheapest.

  If you need 3 or more apps Complete is the way to go.

• Microsoft Silverlight will / can send information about the people and the info on their computer. What are the plans for Firefox to protect its community of users of this?

  After reading the privacy statement from Microsoft regarding their Silverlight 5, it has troubling information about the loss of his privacy, under the "collection and use of information...". "the personal information and the information on my computer! In addition, information may be stored outside of the United States! (paragraph 4 under "collection and use of information... »). As part of the FireFox community, what other options do we have?

  P. S.
  I clicked on "Shared Data" on my Firefox browser, that means all average data? All good or bad I should know about?

  Hello 010matrix010, firefox will not run on the default Web sites, but only silverlight content when a user activates explicitly the plug-in through the icon in the address bar or click on the embedded content.
  also the support for plugins like silverlight in the browser will be dismantled at the end of next year: https://blog.mozilla.org/futurereleases/2015/10/08/npapi-plugins-in-firefox/

• Since an incompetent technician clear my settings from mozilla, I get up to a page of useless information about the sender and want to know how to avoid this

  Since an incompetent technician clear my settings from mozilla, I get up to a page of useless information about the sender and want to know how to prevent it. I can't copy / paste an example, but there are things like x-vipre scanned. x-uidl, x-account key. These things print when I make a copy paper, waste of paper and ink.

  The menu bar, select View-Headers-Normal

  No menu bar? Press the ALT key.

• Information about syncing between a mac and another mac?

  I use notes on my MacBook, my iPhone and iPad. They all have the sync very well in all directions.

  I also share my notes with my wife. She also has a MacBook Air, an iPhone and an iPad. To do this, I added my iCloud account to its devices and use it to share my calendars iCloud and notes.

  Calendars all sync very well.

  Notes were synchronization too - until some time last year, something like mid-October. Since that time, notes don't sync. She sees always points out the way they were at this time. Notes, I've added since then do not appear. Note that I have updated has always been to see the place with old content.  For example, I see a note on my Mac (iPhone and iPad) with a release date of November 11, 2015. But the other Mac, iPhone and iPad, this same note comes with an update October 8, 2015 (and the content is different - not the same as what I have).

  I checked the notes in iCloud. They are all OK: which means that synchronization works very well for my own devices.

  But somehow features my wife appeared to be an old version? I tried disconnecting my account iCloud of its devices. The notes then obviously disappear. I then reconnect my account iCloud on its devices. Notes reappear. But always with their older versions.

  Does anyone have an idea what could cause this?

  Thank you

  What version of OS and IOS uses your wife? If you run El Capitan and IOS 9.X in Notes, you choose the upgrade to iCloud, then they will no longer be synchronized with a computer not using El Capitan and IOS 9.X, which does not have the option Update information about iCloud.

• Enumerate devices OR and get information about the device C / C++

  Hello

  I use using NI_DAQmx.  How to find and enumerate devices OR and obtain information about each device listed in C / C++?

  I am implementing a dynamic configuration allowing to access hardware OR on our system.

  I need to get logical device names, for example "Dev1", and then find what device OR, for example NI 6008, is associated with each device name.

  Thank you.

  -Neil shore

  If you just read the device information while you use DAQmx properties to achieve what you need:

  To get the names of all the devices in your system:

  DAQmxGetSysDevNames

  To get the product to a given device number (each product has a number of unique product in accordance with the reference C DAQmx help, for example, the USB-6008 case is 0x717A):

  DAQmxGetDevProductNum

  If you need to actually define the names of devices or whatnot, you would then focus on the System Configuration API.  I've never really used this outside of LabVIEW, but the Readme indicates he has CVI supports so you might be able to make it work.

  Best regards

• The discs to a hard drive with an IO error can be removed and placed in a good hard drive to try to recover the information about the bad drive?

  The discs to a hard drive with an IO error can be removed and placed in a good hard drive to try to recover the information about the bad drive?  Both units are of the same type and speed.  both are records hard internal seagate w double disc in the drives

  On Thu, 20 Sep 2012 14:41:30 + 0000, Stephen_403 wrote:

  The discs to a hard drive with an IO error can be removed and placed in a good hard drive to try to recover the information about the bad drive?  Both units are of the same type and speed.  both are records hard internal seagate w double disc in the drives

  No, at least not by us.

  Open a hard drive for some reason any at all can be done in special
  laboratory as parameters. Something else will destroy the disk.

  There are companies trying to recover data from broken disks,
  and they are sometimes successful. And who knows, maybe they
  sometimes use methods such as what you describe.

  But if you plan to use such a company, know what they
  are all very expensive. It does not for most people.

  For the future, if you have files you want to be sure are not
  lost, make sure to have in place a backup procedure on a regular basis the
  external media player.

  Ken Blake, Microsoft MVP

• I get threatening and abusive emails to a windows live user, how can I get more information about this user to report.

  e-mails in danger

  I get threatening and abusive emails to a windows live user, how can I get more information about this user to report.

  The information is provided in the source of the message. In OE, Windows Mail and WLMail, Ctrl + F3 reveals this.

• Something going wrong on a server that contains information about your user account and the mailbox can not be found.

  Cannot open the e-mail.  I can connect on the MSN home page and when I right-click the outlook icon it shows the e-mail Inbox, but cannot access e-mail.  I just get this error

  "Something going wrong on a server that contains information about your user account and the mailbox is not found."

  This error is on the MS and they are aware and working on a fix.  Have you tried connecting mail.live.com directly using your e-mail address and the password?

  For later use, you would get more (and larger) response if you posted this in the Outlook.com (e-mail) section, where are the experts.