Inspiron 3737 does not start?

Similar Questions

• (Redirected) Dell Inspiron N5110 does not start

  Hi, my laptop Dell Inspiron N5110 is now 3 years old. I recently had a hard drive fail, then replaced by a new. Now the machine does not start. I have a boot disk in the DVD player that swirls, but gets no further. I get also is no longer the screen Dell displays (before the windows one). In fact, everything is empty. I tried to remove the power supply by battery pack and power holding down the button for 1 minute then re - again no difference. Is there anything else I can do or is the death machine?

  Thank you

  Daniel.

  Please repost this in the laptop computer forum for faster assistance.

  http://en.community.Dell.com/support-forums/laptop/

• Inspiron 560 does not start after the new mobo

  just relpaced mobo with nine years of old stock that it does not start in windows 7, just goes into repair options, but will not repair.

  He's trying to start windows, it happens from windows, you see the glance just color logo on the screen, then it restarts.

  Yes, it's the same model mobo.

  TIA.

  Check the operating mode SATA for disks - it must be about the same as it was before the jury was replaced (AHCI, RAID, etc.).

  F2 at startup to check.

• Inspiron 1564 does not start

  Hi, yesterday an I tried to start this laptop and he has not started. Because it wasn't me the last who used, I don't know if it was too hot or if she switch off suddenly... my dad doesn't remember... xD

  Symptoms:

  The laptop turns on by AC or battery and: screen stays black. Fan starts to run as normally. HARD drive starts to spin at the first time but then it stop (so it doesn't load the operating system). Power led, hard drive and battery works as it should. DVD and usb also have the power.

  Remove one stick of RAM keeps the system as described above. When two slots are free the mobo make 2 beeps, so that it matches the RAM beep code not detected...

  Beeing, push the power button turns the phone off immediately.

  The problem would be that the two RAM sticks was bad? I thought to try with the stick of an another laptop but Im afraid to break a new too...

  Thanks for your response

  Hi Sunnytours, it seems that your motherboard is fine, the problem is that with the screen, maybe you should try pluggin a tv with a vga or hdmi cable.

  If so you see everything fine on the TV or monitor... just buy another screen and replace it yourself if you can, it's easier than you may think.

  Best regards

• Dell Inspiron N5110 does not start

  Hello!

  I went to dell [F12] startup options and ran the diags.

  It throws following error message upward:

  Error code: 2000-0145

  Validation: 45371

  MSG: Hard drive 0 s/N 5VEKQY27, self test has not completed.

  [HD bios is detected correctly].

  What should I do now?

  You will need to replace the hard drive - which, while a bit expensive component to replace, is not easy to access on this model.  You can watch the video below before you decide to replace it yourself - or do a workshop work for you.

  You will need a new 2.5 "7-9.5 mm laptop SATA hard drive (hybrid or or drive solid state drive).

  www.YouTube.com/watch

• Dell Inspiron Laptop with Vista installed at the factory does not start.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: Dell Inspiron Laptop with Vista installed at the factory does not start. The display shows

  Indicator of treatment MM061 series white 80% in all of the BIOS revision A13 treatment indicator always goes to the same place and stops. I tried to tap the F8 key, but nothing happens.

  If you used Dell or the recovery Partition recovery disks to restore the system, you must talk about Dell problem because it's their software - not Microsoft.  We don't know what's on it or its operation.  We have no information to help us help you.  You need to deal with them.

  Sorry we can't be more helpful.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Inspiron 620-7750 Radeon with 450W power supply installed does not start

  Hello!

  I have looked EVERYWHERE online and on the forum and have seen several posts on this topic and still not found a solution that works.  I have a Dell Inspiron 620

  • I5Intel Processor2nd Gen Core i5-2310 / 2.9 GHz
  • Memory8 GB / 8 GB (max)
  • Windows 7 Home Premium 64 - bit Edition operating mode
  • Optical DriveDVD±RW
  • Graphics technology ProcesseurIntel HD Graphics 2000 dynamic video memory 5.0
  • Integrated graphics controller

  Recently, I buy a Powercolor Radeon 7750 graphics card I have installed the drivers, uninstalled the current Intel Graphics driver from Device Manager and then install the new card.  I of course unplugged the PSU got rid of and left in power has failed to myself and plugged into the PCI-E.  After I tired to turn on but it does not start.  Fans begin to turn, including on the graphics card, but nothing comes up on the monitor and it won't start.  When I unplugged the 7750 card it starts very well?

  At first I thought that it was not powered ridiculously horrible 300w PSU they put so that I have upgraded to an a 450w.  Everything works with the new power supply installed without the card, but as soon as I plug the new map, he continues to not start as before installing the card.  I have searched and tried things for 2 days now and CAN NOT find a solution.  I know that the 620 does not access the menu of the BIOS under settings in advance who does not help (don't know why Dell would never think it was a good idea!) so I can't change anything in there.

  Please, any help would be fantastic!

  Thanks in advance!

  The card is a bad card.  There should be ZERO problems with the supply of the stock 305 w and a 7750.

• Wireless zero configuration does not start automatically. I need to run it whenever I restart the computer

  Wireless zero configuration does not start automatically.i have to start whenever I restart the computer. I have a laptop dell inspiron

  Moved from feedback

  Original title: WiFi

  Hello

  1. what version of Windows is installed on the computer?

  2. is it works much earlier?

  3 have there been recent changes made on the computer before the show?

  To activate the Configuration service automatic wireless so it starts automatically, click the Start button. Select settings , then select Control Panel.

  If you use Windows XP display, select the performance and Maintenance category, and then select Administrative Tools.

  If you use Classic view, and then select Administrative Tools. In the left pane, click the Services icon. Click the automatic Wireless Configuration icon in the right pane, and change the box Startup Type to Automatic.

  This parameter will be defined the service starts automatically at boot time. Then click on the Start button to start the Wireless Auto Configuration service zero wireless and click on the OK button.

  The automatic Wireless Configuration can also be started and stopped from a command prompt.

  To start the automatic Wireless Configuration, run the following command:

  net start wzcsvc

  To stop the automatic Wireless Configuration, run the following command:

  net stop wzcsvc

  For more information, see the link.

  Wireless Zero Configuration Reference

  Please post back with the results and we will be happy to help you further.

• StarTech ec1pecps parallel adapter does not start, error 10

  I'm having trouble installing a parallel adapter from Startech ec1pecps on my laptop Dell inspiron 9400 running XP. I tried new drivers and the advice of the other forums, but the device driver says: "device cannot start error 10.» I received no response from Startech on it. Can anyone help?

  Hi GregSwinburne,

  ·         Have you tried to connect the unit to a different computer and check?

  The Code 10 error code is generated when the Device Manager has not enough information or the error that is upward by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  For more information, see the article:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  You can also run the troubleshooter and check if it works.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Let us know if that helps.

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Windows Vista does not start at startup

  I have a Dell Inspiron 1525. My wife uses mainly the laptop for access online, certain professional activities (Word documents, spreadsheets) - nothing major.

  Today, after starting the Dell system, the laptop would not boot correctly. It would have wrapped after the Windows flag and never completely boot. What I have done so far to try (unsuccessfully) the question of setting:

  (1) launch Startup Repair (recommended) - no resolution

  (2) Ran Dell Diagnostics - received error code: 2000-0333

  (2) selectable repair your computer from the Advanced Boot Options and attempted a system restore - it has failed because of an i/o device error (0x8007045D)

  Not sure which is precisely the problem. Please help to troubleshoot and resolve this problem.

  Thank you

  D

  Hello

  Follow these steps using the Dell diagnostic process, especially by pressing F12 at startup.

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=266787

  "The computer does not start in Microsoft Windows Vista"

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=DSN_343119&isLegacy=true

  If Dell information does not resolve the problem, you may need to reinstall the operating system.

  See you soon.

• Vista does not start after power failure

  It is a Dell Inspiron 1525 with Vista 32 - bit, recently replaced hard drive

  My daughter has been using the computer and the power failed due to low battery.  Now, the computer does not start normally and not all programs will run.

  If I choose "safe mode", it hangs on crcdisk
  If I choose 'window start normally' it crashes to the screen of Microsoft Corporation
  If I choose "last known good configuration" then it seems to start normally, but does not all programs run.

  I tried to boot from the OS disk, but it ignores the entire disk
  I tried to run the installation disk once the computer is running, but it freezes.

  Need solutions.  Thank you.

  Hello Bakajanaidesu,

  Thank you for posting.  It seems that you have a hardware error or failure with your hard drive.  In this case, I recommend that you contact your Dell technical support for more information on how to correct this problem.

  Please let me know if I can be more useful. Zack
  Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Vostro 200 desktop computer does not start

  Hi all, our company has an old desk, Vostro 200, which works very well for a few years.  A day after the cleaning, the machine does not start with the amber light.  Fans stop, even the power supply fan stops.

  I tried:

  1. using a different power supply, it's the same thing.

  2. using another CPU, it's the same thing.

  After I unplug power 4 pin for the processor, fans start working and it seems normal but show nothing.

  I also tried out the case from the jury and put it back, in order to avoid any shortened with the case.  It does not work.

  What is the failure of the motherboard? I had a copper shortcut or circuit on the map?

  Although it is an old computer, but we do not produce a bin with other parts in good condition.

  Thank you.

  One last thing is the license Windows XP OEM's sucks it as well as the motherboard has failed because the license is listed in the BIOS?  Thank you.

  CECTT

  Thanks Bev

  1. After spending the Green and black cables, the situation is the same: the fans stop with power of CPU 4 pin; fans of work without power CPU 4 pin.

  2. after disconnecting devices PCI/video /, the situation is the same, still no beep.

  3. after remove the memory, the situation is the same.

  After checking the CPU socket, I put that there could be some not vertical pegs.  Is it possible that I folded a few pins so that it didn't?

  Thank you

  CECTT

  Yes, it is possible, the processor installed correctly, for more information, go to pages 152 to 155 of the owner's manual, if the LGA 775 is damaged, this may require a motherboard replacement.

  https://www.Amazon.com/Dell-motherboard-Inspiron-systems-compatible/DP/B003CO0WQS

  The Vostro 200 was built with two different systemboards.

  Motherboards should have engraved on it model number.

  If she says G33M02, then it only supports Core 2 Duo processors.

  If it says G33M03 then it supports Core 2 Duo and Core 2 quad cores processors.

  What are the OEM sSpec numbers and processor that was installed as a replacement?

  http://www.Intel.com/content/www/us/en/support/processors/000005554.html

  Have you tried to reinstall the original OEM processor?

  In addition, the procedure is usually to Flash the BIOS to the latest version, before the upgrade of the Vostro 200 processor.

  Bev.

• Windows 7 Home Premium does not start and an external monitor connected via DVI to HDMI Cable

  I have a Dell Inspiron 531 desktop computer with a NVIDEA GeForce 8400 GS video card.  This video card has the following outputs: DVI, VGA and S-video.  When I connect it to my computer via the VGA port to PC to my Sony Bravia KDL-40XBR4 monitor port, the machine starts perfectly.  If I connect via a HDMI cable to one of the HDMI monitor DVI ports, the screen displays the video BIOS, but turns black when the operating system begins to load.  If I connect another monitor to the VGA port, yet once the machine boots fine, but if I connect the monitor to the computer and the Sony Bravia, once again the machine does not start.  The strange thing is that if I boot with only the connected computer screen and then plug the DVI to HDMI cable, then Windows 7 sees the Sony Bravia monitor very well, and I can extend the desktop.  If the machine mode 'sleep', both monitors work very well to wake up the PC.  So, if the Sony Bravia is connected alone or with the computer screen, the machine does not start (the screen will display 'go black' when the OS starts to load.)  I tried to run Windows in Mode safe, but he won't either.  I have all the updates of Windows applied and have installed the latest drivers from nVidea so.

  Hey Chris,

  First of all, about climbing, is not a technical support; This is a community forum where MS moderator and contributors are involved.  Now to your question ~

  It's very strange that the PC does not start when this unit is connected, but works fine when connected after the fact.  I've seen several cases where a hardware configuration of uinsusal will prevent a PC to boot.  I think that the culprit may be DVI to HDMI Cable that you are using.  If I were you, I try to connect the PC to a DVI monitor and see if it boots normally.  Also, see if the monitor can prevent another PC to start when it is connected directly via the HDMI.

  Good luck! Let us know how it turns out.

• Inspiron 530 does not read CD

  PC: Inspiron 530

  My computer could not read some cd of I. Diablo 2 LOD and the installation of the Pinnacle studio disc CDs are displaced but the computer does not start or the installation on the desktop, it shows nor even i.e. a CD in the thing when I go in my computer.