install problems in time real 8.6

Similar Questions

• Lance Muse problems, every time I launch Muse, it crashes, I have re-installed twice with without success.

  Lance Muse problems, every time I launch Muse, it crashes, I have re-installed twice with without success.

  Hello

  It might be because of permissions. If you are on a MAC, you can give permissions ' read & write ' to everyone on the following folders: -.

  (1) ~/Library/Application support/Adobe

  (2) / Library/Application Support/Adobe

  ~/Library/preferences/Adobe 3)

  On a windows machine, please give all permissions for all on: -.

  (1) C:/Program Files(x86) /Adobe

  Files(x86) /Common 2) C:/Program Files/Adobe

  Kind regards

  Neha

• Time real 8.6 and PDM

  Hi all

  Using a CRIO-9012 with time real Labview 8.6 and labview 8.6 and now that TDMS is supported and I am wanting to use it on my cRIO. Be a problem if... in addition to open or close tdms files still do not work on my CRIO even if time real 8.6 is installed. Attached is a simple vi which works on my PC but not on my cRIO, tried still more simple screw with on the CRIO tdms and it does not work. When I try to run the program on the cRIO I just lose the connection to the controller and have it reboot. It is likely to what I may have missed?

  Thank you

  Jevon

  I came across a question like this and found that the path of the file to open it TDMS must have a tiny 'c' as in "c:\". "instead of"C:\ ". »

  You will always get an error on the end, but the IO files works.

  Kurt

• Get information about the physical location (serial) Visa (slot) in PXI time real (Pharlab)

  Hello

  I PXI system with controller time real (OS Pharlab) and many maps series (about 6 cards).

  The maps in the series are two different models, which each contain several (8431/8 and 8421/8) serial ports.

  And the COM Port enumeration mix and I would like to know the link between COM numbering where it is linked.

  I have already dealt with a few methods:

  1. I've tried using the node property of Visa but he cannot know which card port COM belong

  2. I tried to use the Configuration Library system and don't manage to get general information of the card and not what ports have this card.

  3 try to fill you with the VisaConf.ini, but discovers that ASRL and COM Auto-enumeration is the same.

  4. I tried to look in NISerial.ini, NISerial.dbs and NOR - RT.ini and did not find any help here.

  Application engineer or support suggest to look in the registry of the operating system Pharlab because it is windows based and material information must be stored in the registry

  Further explanation on the problem of PXI enumeration:

  PXI produce enumeration auto for the ports series (COM3, COM4, COM5...) according to the card slot, but when there is a mix of the two models of the system would then list a model (8431) from 3 to 50 (6 cards and 8 ports) and the other model (8421) 51 to 98. so if I have 8421 in 2 and 8431 slot number in the slot number 3 it would list 2nd slot COM59 to COM68 and 3rd slot COM11 to COM19.

  Why not just use NOR-MAX to manually configure the ports?

  The system is essential and can not be stopped for a long time and he operated by people who are not very technical, so the customer who wishes to be able to exchange business cards without futher configuration.

  Thank you

  Or Hirschfeld

  Application engineer

  SK-Electronika, Israel

  www.LinkedIn.com/in/orhirshfeld

  Solved and download the example of solution of community

  Get the location COM (Serial Port) and Port physical location in the chassis

• Lack of time real plug-in

  I have a project in real time using a 9074 cRIO chassis. The project opens fine on my desktop but when I try to open it on my laptop, a yellow triangle with an exclamation mark inside appears at the level of the chassis and don't see anything below the level of the chassis. If I right click on it, it just says: "the plug-in for the selected item is not installed on your system or the plug-in has a license has expired. I have installed all these elements on this machine:

  NIRIO1310f1

  LV 2013 SP1

  SP1 FPGA development

  SP1 of development in real time

  NIDAQ1400f1

  Don't know what else I could possibly be missing, don't remember installing something more on my desk? No matter what project I try to open, any project won't let me in time real access below the chassis level. If anyone knows what I could miss I would appreciate the help. Or if you need more information.

  Thank you.

  I installed NIRIO14f1 and my phone seems to work again.

• Average displacement Subvi does not refresh the data in time real host VI

  Hello!

  I time real host VI that has evaluate the NI 9215 cRIO block data 9073. He takes analog data and calculates the phase shift. It works well with the connected equipment and displays the results. I need to get the moving average value of phase shift, so I add moving average Subvi, where main VI entries - new value (phase shift measured) and ms and output - average value of travel time. When I run real time host VI it gives me a single data and stop get new data from Subvi. It refreshes not even values measured in real time. So the problem somewhere in the accommodation, with sub - VI. How it can be solved? How can I get real host VI with the moving average value of Subvi update running time?

  Thank you.

  Your problem is that you have a loop that runs until you press the Stop button inside your Subvi.  If you try to use a Global Variable that is functional, you have a few things wrong.

  1. the loop should run only once.  A TRUE to the conditional stay Terminal wire.

  2. the shift register cannot be initialized.  That is how he can keep the old elements in a story.  Use a first call? with a case structure so that you only initialize the table of history inside the loop on the first time the VI is called.

  But if you really want to make your life easier, just use the PtByPt.vi mean.  NOR did all the work for you.

• My SSD with a version of Dreamweaver CS6 running crashed. Now a new SSD is installed and every time I try to reinstall DW CS6 error "inconsistency in the database Setup" (in German terms) occurs. I tried to delete everything about t

  My SSD with a version of Dreamweaver CS6 running crashed. Now a new SSD is installed and every time I try to reinstall DW CS6 error "inconsistency in the database Setup" (in German terms) occurs. I tried to delete everything about CS6, rebootet and so forth--nothing worked. Two hours later, I tried to install DW 5.5 - that worked. Then I tried again to install 6.0 - without success. Can anyone help?

  Thank you for your response. I could not find caps.db.

  Meanwhile, I solved the problem as follows: I searched "dreamweaver" everywhere one deleted all that I could find. Then I googled "CS6" and did the same. I guess that there are around 20 or more places where I deleted files or directories. Suddenly, installation has not prevented, to 2%, what he has always done before and the installation was a success :-) It cost me more than 4 hours to understand this, and I have found a trick somewhere really help. Adobe itself I could not contact because I couldn't find an email address or a phone number - poor support for such expensive software. For luck, I didn't deliver something just in time. Missing a useful support, it's an attitude really poor, poor Adobe... I think that I do not buy not more products Adobe - it could cost too much of my time... :-(

• Create a subfolder of bookmark in time real bookmarking a page in a folder that I created for a registered earlier does not work

  Create a subfolder of bookmark in time real bookmarking a page in a folder of bookmarks, I created a saved bookmark previously does not work.

  Previously on a Windows XP computer, I could choose the "select" option and create a new folder under the folder I chose to put my new bookmark. "." On this computer, the 'new folder' option is not clickable.

  I thought about it. Thanks anyway.

• The recovery W530 instalation problem

  I am trying to install the factory system on Lenovo laptop, W530, since the recovery discs original dedicated to the Lenovo W530 (Windows 7 64-bit), and the instalation stops some time after that I chose that there is no additional disks (I mean there is no statament, just the bass progress stops with no message). I tried the recovery disc for X 1 carbon too with the same effect. What could be?

  I found another recovery - T440 and he helped

  Don't understand, buy it functioned (instead of the one dedicated).

• using the module time real Labview in RTAI

  Hi all

  I want to use the module time Labview in RTAI real for real time due to its open source applications and very good performance. is it possible to make this work?

  If this is the case, can anyone introduce a single study of case or something similar to this?

  Cecile says:

  Hi all

  I want to use the module time Labview in RTAI real for real time due to its open source applications and very good performance. is it possible to make this work?

  If this is the case, can anyone introduce a single study of case or something similar to this?

  I don't think it's possible for anyone outside of OR. LabVIEW Real-time supports this time only Windows as host and as a target only material of National Instruments with specifically targeted OSes or the Pharlap ETS system on x 86 systems with hardware specific enough. Using RTAI as target OS for LabVIEW Real-time applications requires first a few changes on the time plugin real LabVIEW to support this new platform.

  None of the files in time real LabVIEW also created for either platforms OR running VxWorks or OS Pharlap, Pharlap ETS system woud be able to be deployed to a system RTAI, because they are not compatible. In the first place, you'd have to port the bunch of shared libraries that make up the time target real system running LabVIEW on one of these goals to your RTAI system which is in fact a whole new platform of LabVIEW you can create with a little effort from the LabVIEW source code. It's not really impossible for OR as most of the code LabVIEW is written platform completely independently, but it would be a combination of the parameters compilation for course LabVIEW Real-time, with the settings to produce time targets real LabVIEW VxWorks with some additional settings of Linux. Yet, it would be by far not trivial and some parts are actually hardware specific drivers that must be worn too and limit the possibilities of what RTAI material could serve even further. In short not something that would make any commercial sense NC because they invest a lot of resources with no opportunity to sell additional hardware.

  And hell freezes over up front release of NI LabVIEW source code in any form which gives access not - OR used to it!

• Time real ADC/DAC for SMPS by using Labview and USB

  Hi all

  I asked the Sales Department of this same question, so here's a two-pronged approach:

  I am reserching a control algorithm for power switching, and so far, its performance simulations seem to be good.  Now, the goal is to implement the circuit from the experimental data.

  I've seen several NI USB DAQ boxes that seem to have the performance, I'm looking for (for example, the box USB-6211 a sampling rate and resolution I need).

  The control algorithm uses the following mathematical functions: add/sub/mult/div/exhibitor and derivative/integral.

  My question is this: is "strong enough" Labview take four-channel data 250Ksps, crunches the numbers in an equation and spits out the answer to an analogue on the channel, while time REAL?  I'm looking for a rate of analog output of ~ 100 kHz.

  Thank you for any suggestions you have!

  -Rick

  Hey,.

  So if you were trying just to perform an input or output, then the box USB-6211 would certainly be able to treat it as the machine clock could manage the inputs/outputs, no software. However, what you are wanting to do, basically a feedback system, he will have to avoid (at least to a USB device) because you need to be able to specify Active which is the output. So, for this reason alone and the fact that you want out of 100 kHz, this device and the USB devices in general will be not an option any what software you use, LabVIEW or otherwise. On another note, you want to make sounds more like live update, not in real time, which is more on the jitter. Bottom line, for these kinds of requirements, you might need to move to an FPGA card, something like the NI PCIe-7841R would work. It's more expensive, but for your needs, FPGA will be the only option and it comes down to the latency of the bus, but also the response time of software. With FPGA, as shown in the first scheme of the following document, you basically close your software through hardware loop.

  Basics of FPGA

  http://www.NI.com/white-paper/6983/en

  -Ryan S.

• In time real CRIO - writing a file on a PC hard drive

  Hi all

  I am developing and application with the following hardware features:

  Time real cRIO 9004 target device

  HAVE cRIO 9205

  AO cRIO-9263

  and the following programming features:

  I run an FPGA VI to establish PID control where the reference signal generated in the FPGA and the real is an acquired signal through the cRIO 9205.  I also find target FPGA FIFOs host in order to pass the data from the FPGA to the application of the RT.  The time real VI will run in the 9004 cRIO processor.  Now, with the data from the FIFO I would write a file (regardless of the extension), in order to do more tests.  I did it but I don't want to use the local memory of the RT, instead, there will be a PC (hard drive) where I can place the file in order to write it (with data).  I'm not able to do so, as 1) I don't know how to call the PC hard drive and 2) I don't know what communication protocol fits better I want to develop a device to Windows Welcome.

  Nobody helps me?

  Thank you very much

  Enrique

  The cRIO-9004 unfortunately has USB, so you can not write on a USB Flash drive (which would be my first suggestion).  If you want to store the data on the host PC, you will need to write a simple TCP/IP client/server to send data to the host through TCP so that the host can receive and save to disk.  Façade of the VI may seem as it is running on the PC, but it's actually just show you data be listened to the target (you are not allowed to piggy-back on this same Creek).

  There are several examples of TCP/IP client/server integrated into LabVIEW.

  -Danny

• Problem of time synchronization in the HP b2600 workstation.

  We have three Hp b2600 named rop11, rop12, rop13.

  rop11 is active and rop12 is passive and rop13 is autonomous.

  ROP's time synchronized with the GPS clock. But we face a problem of time synchronization.

  As we sychnisied a day after we saw a drift of about 10 seconds in rop11 and 1-2 second in rop12 & rop13.

  ntpq shows according to the attached file.

  TW file attached, one is Parallet1 where the existence of the problem and another is PArrallel2 where its not working OK.

  PL. suggest the cause and cure.

  Thank you

  Rajiv Garg

  Mr President.

  All the vause zero in Parallel1.doc comapring and PAralle2.doc, which indicates how to initialize the same.

  Rajiv gelin

• remove the pop up message "Waiting for in time real (target CompactRIO RT) to answer.

  Is there a way to remove the pop-up message "Waiting for in time real (target CompactRIO RT) to answer" what power is removed the cRIO or when the network cable is disconnected?

  Hey Danny,

  How did send you the commands to the Windows PC the cRIO? You use the remote FPGA host Interface?

  I've seen the pop-up dialog box when the LabVIEW project is not present.

  If you create a Windows VI that sends orders via shared variables or other network mechanism to a VI RT, which in turn controls your FPGA VI, then you should not ever see the popup you speak.

  This tutorial walks through creating an example of monitoring on cRIO with three screws as indicated:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/11199#toc4

  This tutorial is an example of the use of a shared variable to implement a heartbeat, to determine if the cRIO is connected:

  http://decibel.NI.com/content/docs/doc-11046

  I hope this helps.

• Execution of several executables in time real (.rtexe)...

  For PXI (or any embedded controller OR) several executables in time real developed in LabVIEW (.rtexe files) can work simultaneously?

  I'm almost certain that the answer is 'No', because the whole point of a RTOS is the code to be "as deterministic as possible", with the Jig and schedule reduced by removing items (such as "interference of the BONE") out of control or understanding of the developer.

  Pouvez, however, write a single RT executable that loads into two routines that work "in parallel".  If you have a multi core processor, you could book separate processors for two routines that should improve their independence from each other.

  We met a slightly different variant of this issue during the migration of code LabVIEW 7 to a LabVIEW Project "oriented" development (introduced in LabVIEW 8.x).  We used to have several different programs of LabVIEW RT who has used a code different on the PXI - when we ran the host executable, it loaded and run the appropriate code of RT (recorded in a .llb).  This works well with executable RT.

  What we developed was a system where we have recorded each RT executable as a routine named separately ( not Startup.rtexe) and set them (initially) to run as a startup.  When the host code runs, it queries the PXI for the name of the startup routine, and if it is not 'just', change us it on the PXI and make the PXI to restart.

  [In fact, don't really do us this way, that 99% of the time, we always run the same executable RT.  What we did do was to write a separate "define RT Startup" routine that we almost never executed, unless we "know" we run an earlier version or something like that.  This, in turn, tells us that the PXI is configured to run and what executable RT can be defined as startup, then makes the changes, restarts the PXI and exit.  The 'rule' is that if you change the executable RT, don't forget to change the back when you're done.]

  Bob Schor