A single / Multi channel divergence in VI for unit piloted by GPIB

Similar Questions

• Cannot create the multi channels Tx two USRP-2943Rs Session with driver

  I have problems of implementation of several USRP-2943R devices in tranmist both of their channels at once.  Right now my configuration is a configuration of four chains composed of two devices of RIO.  I am only able to transmit at the same time successfully CH0 and CH1.  I'm creating a session using two devices and my aim is to perform Tx on CH0 via CH3.  In addition, my goal is to use the LabVIEW driver without any synchronization, because I test fix synchronization through post-processing and you want the VI be as simple as possible without the hassle of FPGA programming. I realize has the Simple models OR - USRP Streaming Sync in LabVIEW, but additional synchronization and FPGA programming is too much for such a simple project like mine which would require no synchronization USRP.

  My VI and some screenshots of the error messages resulting is attached.  I am able to succesfully implement multi-channel Rx deals and attached is my multichannel Rx VI.  My question is why I can open and operate a session of Rx mult-channel without problem, while a multi-channel Tx session will give me errors?

  My final goal is to merge my multichannel work Rx VI with a mult-channel Tx VI work for measurements in order to test some synchronization post-processing routines that are performed in Matlab.

  I think that I found a solution to my problem.  I thought to post it here to help others.  It is important to use some sort of device to synchronize several USRPs.  However. I found that you must reset the device by setting the node of reset function blocks that open and session Rx or Tx.  "" If it is not defined, then the ' niUSRP Signal.vi configurethe ID of the specified attribute is not valid for the scope specified (or channel)." error occurs, any circuits that you define.  After the node Reset true and place an empty string for my channels Enabled, all was fine.  Also, a full duplex system you will be only to first log of Rx with a reset of the device, followed by the opening of a session of Tx without a reset of the device.

  One more thing, it is that there seems to be a bug if you feed a Tx process a table whose number of lines does not match the number of channels Tx.  This will result in weird errors funny will disappear only after doing a hard reset of the units.  So, just something to take note of.

  I hope this information will help others and this message can be marked as resolved.

• Multi-channel acquisition - simultaneous Acquisition of sampling 1 & 2-channel single sample in a task

  I am able to get a multichannel simultaneous sampling on my acquisition of data (USB-6363) without problem. But what I want to do is make multi-channel acquisition in a single task where sampling requirements are different for each channel. For example, I want I want to acquire a total of 1000 samples on 3 channels in a single task with DAQmx as follows the characteristics of sample:

  • AI0: Analog Wfm 1Chan NSamp (998 samples)
  • AI1 + ai2: 1 d analog NChan DBL 1Samp (1 + 1 sample/channel)

  I know I could do just a regular multiple sampling multi-channel acquisition through all three channels then average down from channels 1 + 2, but I don't have that several samples to spare. AI0 is a bandwidth hog in my application and consumes all the samples of data acquisition (2. MECH / s), but I can save a few samples to make analog measurements further (for example, temperature, pressure).

  Ai0 takes place also permanently so additional analog measures on ai1 + ai2 need to be included in the same task.

  I don't know how to go on this matter or if it is still possible. Any ideas or thoughts would be greatly appreciated.

  Currently I use a second DAQ to read these additional channels at a lower rate but I need to pass a single data acquisition.

  How should continuous ai0 really be?  You of course can enjoy on ai0, and one of the other entries at the same time, then there would be some gap in your data.  In addition, if you want to go to the full 2 MHz, you may sample ai1 ai2 twice in order to allow entry to set (the maximum specified multi-channel rate is only 1 MHz due to compaction of the constraints on the MUX I believe).

  DAQmx sort of you lets set something up like that, if you "cheat" it by configuring each sample as a single channel in your task (see an example similar here).  If your 998 + 1 + 1 (or 996 + 2 + 2) becomes a task of channel 1000 (takes a bit more memory, but should still be feasible).

  I would consider a 2nd DAQ card a better option if ai0 really needs to be continuous.  You can go with a (9174 or 9178) cDAQ chassis a 9223 (only 1 MHz if) for quick entry and your choice of module for the slower entries.  On the cDAQ chassis a module can run a separate task of AI from other modules (up to 3 tasks HAVE by chassis) at different speeds.

  Best regards

• Generation of weather in TDMS for measures of multi channels channel

  Hello world

  I have to write an application with five measures will at the same time... then it must be saved in TDMS each channel being its own channel of time just after she... IE sequence of the canal as below

  Channel group

  Measurement1

  (EDT) 1

  GCA2

  TIME2

  Measurement3

  Time3

  Measurement4

  Years.4

  Approvisionnement5

  Neuve5

  Each time channel should have "dt" for its number of measure...

  So far, I m succesfull in the measuring channel recording only all the... But I have no idea how design for each measurement time line...

  I tried to get the time I receive the data using functions as below

  GetSystemDate (month & day, &year);)
  GetSystemTime (& hours, minutes & seconds);
  sprintf (timeStr, ' %d/%d/%d % 02d: % 02d: % 02d ", day, month, year)
  hours, minutes, seconds);

  This will generate the channels of chain of time... but my requirement is of data type ' Date/Time' used on larger scale of the axis in tiara...

  Any help

  Thank you

  HS

  HS,

  There are two ways to store calendar for a channel information in a PDM file.

  You can only use the first method if timing information is regular (spaced), which means that it can be described with the only values t0 and dt.  This method translates a single channel in tiara which contains data values and stores the calendar as properties on the channel information.  Note that in this case DIAdem will treat time as relative values with no basis of absolute time values. The properties you must set on the channel are:

  (1) wf_start_offset (mandatory), the type is TDMS_Double, contains the time value t0 of the first data point of some units that you use and can just be 0 if your t0 value has no meaning other than as a reference for all other values of time in this channel point

  (2) wf_increment (required), type is TDMS_Double, contains the dt in whatever units you use

  (3) wf_samples (mandatory), the type is TDMS_Int32, contains the number of samples in the waveform

  (4) wf_xname (Optional), type is TDMS_String, contains the name associated with the x-axis of time and will be used by the tiara to label the x-axis in tracing this waveform

  (5) wf_xunit_string (optional), type is TDMS_String, contains a string that describes the x-axis of time units and will be used by the tiara to label the x-axis when tracing of this waveform

  You can set the properties above using the TDMS_SetChannelProperty function.

  You can use the second method for regular or irregular (not also spaced) timing information.  This method translates a channel with your data values and a separate second channel which contains the absolute timestamp values. From your original post, more like what you want.  In addition to your data channel, you must create a channel of timestamp.  Call TDMS_AddChannel with a data type of TDMS_Timestamp to create your channel of timestamp.  Call TDMS_AppendDataValues with the values of type CVIAbsoluteTime to write the Timestamp values in this channel.  You can create individual type timestamp values CVIAbsoluteTime by calling the functions of absolute time in the ICB Utility Library, such as GetCurrentCVIAbsoluteTime and CVIAbsoluteTimeFromLocalCalendar.

  I hope this helps.

  -Jeff

  NEITHER

• Imaging multi channels using the acquisition card OR

  We have a 1408 IMAQ being controlled by LabVIEW 8.0.

  We want to install multi-channel of imagery. All the channels work individually. However, when I was trying to show two channels simultaneously, single channel works and I got the following error message:

  Error 1074397150 has occurred to IMAQ enter Setup.vi

  Possible reasons:

  NOR-IMAQ: A timeout error occurred while you wait for the specified event. If you expect a picture, make sure all the video data is acquired during the period. If you wait for a signal, check that the assertion of signal occurs within the period.

  Sometimes I get a different error message asking me to assign different buffers to both channels. I understand that IMAQ 1408 has only analog digital (ADC) converter to digitize the incoming video. It may acquire up to four different cameras, but only of a camera at a time.

  I don't mind do frame rate in half. I think to show only one channel at a time and do the two channels alternantly. But I need to know how config routes to get there.

  I've attached an example that should work.  I could not test it because I don't have the equipment, so it might need some settings.  I would test it with one channel by setting the channel # 1.  Once it works, define channels # 2.  I set the display to use snapshot mode so the same image can be used for all screens.

  The only reason that I can think of that would make multi-channel acquisition fail when single channel works is the lack of synchronization between signals.  The start of frame signal must be the same for all channels.

  Bruce

• How can I get multi channel audio via the HDMI port on an early 2015 MacBook Pro?

  I try to get the 7.1 audio channels to flow from my MacBook Pro to a cinema set up. The display works fine now I plug the HDMI in however the sound still Mac speakers. I checked the settings and no HDMI output is available. An airtime option is available, but that returns only two channels as a maximum to the receiver. When I go to the configuration of the source on the receiver it receives video at 1080 p 60herts however it is specifically stated No Audio from the Source.

  Also, I have connected my iPhone 6 s more using an Apple through the same HDMI cable adapter and it works perfectly. We also use HDMI with our PS4 occasionally and it works perfectly, even with the 3D.

  Thus, the MacBook Pro is early 2015 with an i5, the receiver is a Harmon Kardon AVR 2700 (we run 7.1 channels of this) and we are connecting via the HDMI port through a 50 ft HDMI before. The receiver sends the audio to a projector with 1080 p 60 hertz if it changes anything...

  Also if it helps the receiver supports dts - hd master audio decoding, Dolby True HD/Digital Plus decoding, HDMI 1.4 (HDMI is compatible 2.0), as well as multi-channel input and PCM and linear PCM.

  I use a "Behringer UCA202' audio device I bought on amazon.com for only $29.

  It works very well for the audio 5.1 or 7.2. Works connect optical toslink. Just plug it into a usb port on your Mac and a cable optical toslink to your AV receiver.

  My Yahmaha 7.2 audio/video receiver is measuring process the digital signal in THX, DTS, Dolby digital Pro logic, a cinema, etc.

  

• Question: BDP-S570 or BX57 internet multi-channel flow?

  Hi all, I noticed recently that when I listen to the audio or video content on the network as my BDP-S570 diffuse now as a multichannel surround sound instead of the 2 stereo channels.
  I don't know if this is caused by the latest firmware I installed or changed content providers (or the Sony Server site) in a recent past a few days to send their audio in 5.1 multichannel, now. Or finally if my BDP-S570 went buggy and it's stuck in the PCM multi-channel streaming mode.
  It broadcasts my network all music and video internet connections in multichannel sound, even if I put the BDP-S570 "Downmix" mode setting of stereo 2 channels. I swear before I made this latest firmware update, I always had that 2-channel stereo audio from the internet network connections.
  So I need to know and ask if someone else becomes sound mode of 5.1 channels of their Internet stream?

  Update: too bad people, I found my answer. The cause of constantly multichannel PCM streaming of all my network connections was because I had the BDP-S570 DTS parameter defined on ' Neo: 6 Music ' instead of 'Off' in the settings menu. I set this to "off" and all the music from the internet is now back to regular 2-channel flows. for info. case solved.

  I'm glad that you managed to fix the problem yourself. If you have additional questions, please let us know and we will be happy to help you.

• Simultaneous multi-channel Imaging NI PCI-1422 or 1424?

  We have an IMAQ 1408. We want to make simultaneous multi-channel imagery. However, 1408 has only 1 A/D converter, it cannot acquire multiple channels simultaneously. We are looking for possible upgrade.

  The NI PCI-1422 or 1424 seem to upgrade products of 1408. Can someone tell us if they can do simultaneous multi-channel Imaging?

  Sorry if this isn't the right forum for me to post this question. But I called the customer service OR. The guy doesn't really know acquisition cards. I think that there are more experts here.

  If you have analog signals, it is a little more difficult.  NEITHER ensures more hardware to read signals from analog cameras.  I don't remember all of their equipment, be capable of more of an analog input signal simultaneously.  They always alternate between the signals, a reading at the same time frame.

  Your best bet would be to get an analogue to digital converter which converts the formats I've mentioned.  You must make sure it is compatible (uncompressed, industry standard, etc.).

  Bruce

• Cannot get DTS/multi channel audio via HDMI

  Hello
  I'm trying to connect my VAIO SVT15112CXS to my Bravia HDTV via HDMI to get multi-channel audio (DTS/DD) from my Bravia HT (connected to the TV via optical) with no luck at all.

  I have the same setup for PS3 works well, is it cable or equipment.

  I have already updated all the drivers.

  When the TV is not connected I don't get an Audio HDMI option in the playback devices (I checked to show disconnected devices / disabled) and when it is connected I do not get an option to change the configuration of stereo speaker.

  This way I get only Stereo sound.

  I tried passthough HDMI via ffdshow config (installed K-Lite codec pack) and there is no sound in this way.

  Is there a solution? something escapes me?

  Thanks to all in advance,

  Thanks for your time and your response.

  I got it actually work! updated drivers audio and video (not Sony ones sugested, but later of Intel and Realtek) and now I have everything works as it should.

  The only minor problem is that Vaio Care now wants me to go back to the previous version of the driver, but I'll just ignore it.

  Everyone, try this if you experience this problem.

• play several stereo channels on a single mono channel tia sal22

  Hello all

  I have a vi that creates multiple stereo audio signals
  in labview 8.6.1 and I would play all stereo channels on a single Mono channel
  is this possible?  I tried setting all the device ID's for the same thing, but a lot of clicks and POPs has occurred.  Basically, I'm playing and mix all the signals on a single mono channel at the same time.

  Please note that I would have each created signal played on
  the mono channel at the same time.

  TIA sal22

  sal22 wrote:

  Thanks, but what options allows me to do this

  TIA sal22

  Just add the berries if they have the same length. Use the standard add function (as in 2 + 2 = 4). The tables are then added to each index is added

• AI trigger and measure multi channels

  Hi all

  I have a simple problem (using USB-6259).

  can repeat the measurement trigger of AI and measure multi channels, but not both at the same time.

  -DAQmxCreateAIVoltageChan(hd, "DEV1/ai0",...)                    define the ai0 as the trigger channel

  -DAQmxCfgSampClkTiming

  -DAQmxCfgAnlgEdgeRefTrig

  -DAQmxStartTask

  -DAQmxReadAnalogF64 (hd, "DEV / ai0:3 ', / / I want to measure more channels"ai0:3"not just"ai0")

  Thank you

  Hassan

  Hi Hassan,.

  If you use an analog trigger with several analog channels, you will need to use the APFI0 input as source of relaxation. See this KB: Why do I get error-200264 when running analog reference trigger? All you need to do is to connect your analog signal online 0 to APFI0 (Paperback 20 in your case) and set the source of relaxation at APFI0.

  The reason is that you don't have that an NOC on Board (series E or M) and she's going to have to switch between the different lines (see this KB: modes of sampling). This parameter collides with the idea of a trigger analog reference on a specific line (constant sampling of data in a ring buffer up to what a condition is met). The APFI0 line, however, has its own CDA. Therefore, it can run simultaneously.

  However, please note that the ADC is fast but has lower resolution to HAVE it sampling ADC. See these KBs: series E and M series Analog Input Trigger resolution, be aware of a possible error between the analog trigger threshold and the value of the first sample

  Hope this clarified the issue.

  Best regards

  Peter

• I'm trying to export multi-channel audio as apple pro res 422 HQ, but the tracks are all coming full joint rather than separately. I've implemented the multi Channel sequence already. What I am doing wrong?

  I'm trying to export multi-channel audio as apple pro res 422 HQ, but the tracks are all coming full joint rather than separately. I've implemented the multi Channel sequence already. What I am doing wrong?

  All 4 titles are coming as complete blends not divisions. I guess that's a problem with the entrenchment of the channels, but can't see how to fix. Andy

  Is what would you say to my quick thought without following through all the processes after the fact, the sequence settings? My thought is that the sequence settings must be multichannel as you show, but each Adaptive track, so this channel map is routed at your leisure. If this is not the case, already, it would create a new sequence with these settings.

  I try to upload the photo

  

• What software do I need to divide a wilting of the multi-page pdf file. For example 10 pages in a document and I only need to have page 8

  What software do I need to divide a wilting of the multi-page pdf file. For example 10 pages in a document and I only need to have page 8

  Adobe Acrobat (not Adobe Acrobat Reader).

• search engine for a single click is blocked on "search for firefox search engine ' all the time, whenever I changed it and it will not remain as google, it will return

  search engine for a single click is blocked on "search for firefox search engine ' all the time, whenever I changed it and it will not remain as google, it will return

  I want it to be as if it were before, google as my main search engine

  now its still stuck on "search for firefox search engine" which is the yahoo search engine that is really garbage

  In addition, your Firefox is identified at the forum as version 38. An update is available: this article describes how to get 49 Firefox using the "About Firefox" dialog in the menu help: Firefox update to the latest version.

  If something is holding you upgrade to Firefox 49 (or if you use the ESR, Firefox 45esr series), please let us know if we can offer you solutions or workarounds. Version 38 is not safe; Mozilla reveals security flaws after each new version.

  Sometimes Firefox reports the wrong version, because this information was frozen in a preferences file. If the troubleshooting information page shows Firefox 49.0.2, you may need to clear this incorrect information. See:

  • Use the troubleshooting information to help solve the problems of Firefox (first table should indicate your current version number)
  • How to reset the default on Firefox user agent

• How to become a dealer for creative cloud for United Arab Emirates

  How to become a dealer for creative cloud for United Arab Emirates

  Hello

  Please see:

  Adobe - Adobe Partners

  I hope this information is useful!