installation and restallation

Similar Questions

• On 10 Windows, Firefox installs and loads, but crashes at about 15 seconds later, even if I do nothing. This can be corrected?

  This was happening on Windows 8.1, just until I upgraded. There are so many updates happening that I don't know what could have triggered this. I think I had just updated Flash and I see some comments on this. I tried the beta version of Firefox with the same results. It of just crazy that it installs and actually loads, but only for a few seconds and then it freezes and comes from the box with the message to send to Mozilla. So far, no help from them. A few times he asked me to synchronize my Firefox and this process has started, but then it crashed before it finished.

  Sorry, you're not on a Mac. This is a correct version of the above for Windows:

  Thanks for incident reports. Unfortunately, I think you need to temporarily disable or remove the iCloud bookmarks extension until the source of the problem or conflict is determined.

  Start Firefox in Safe Mode by holding down the SHIFT key when you start Firefox. A small dialog box should appear. Click on 'Start mode safe' (not update).

  Then, you can delete favorite iCloud of page modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then you can find it on the right side.

  After leaving Firefox and run it again (not holding SHIFT), runs from Firefox?

• Installation and first run of the FF, I get a box that obviously requires a response, but it contains no words, and does not occur when you click it.

  Installation and first run of the FF, I get a collection box that is displayed for about 5 seconds after the program loads and displays the first screen. It obviously requires a response, but it contains no words. The box doesn't cause any Word show either. the screen takes over and no other button cannot be clicked: I have a hardware failure on FF.

  Empty the gray bar, box, box white, question mark?

  This irritating box was related to an add-on for AOL. In order to remove the extension of the problem, you will probably need to start Firefox in Safe Mode so that it does not work.

  You need to close Firefox anyway, you can, for example:

  • ALT + F4
  • Right click of its mosaic on the taskbar > close all windows
  • (Ctrl + Shift + Esc) Task Manager

  To start Firefox in Safe Mode, hold down the SHIFT key while double-clicking the shortcut.

  A small dialog box should appear. Click on 'Start mode safe' (not update).

  Then you can go to the Add-ons page using either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then on the right, locate AOL.

  A little luck?

• Need HELP! -The installer and excutable issues

  Hello

  I created a Labview installation program to install an executable file (.exe) on a clean machine, who has no any product of Labveiw, so the executable can run by itself without the evoriment of development. Given that the program needs to use sub - VI DAQmx so I include the engine runtime and DAQmx and everything that makes setup > 1.2 GB. At first everything went well.

  Now, we have to make some minor changes in the source code. My question is, what do I have to redo the installer every time for minor changes? I've seen the system creates several files when I build an executable:

  An .exe file

  A single file .aliases

  A configuration file

  A "Data" folder

  Can I just copy these files to a place so new version of the executable file can run without HAVING to build a new installer which exceeds 1 GB?

  Any help or suggestion is greatly appreciated!

  This is the same process as the regular creation of an installer.

  Way the easiest is probably to copy your existing full installer and then removed the additional installers of the copy and rename your copy as a hotfix.

  (i.e. make sure you just deselect the additional installers of the page indicated on the attached screenshot)

  

• How can I disable the Mappoint 2006 for the installation and the reactivation on new computer

  How can I disable the MapPoint 2006 for the installation and the reactivation on new computer

  This forum is for posting comments on the web site of Microsoft Answers, only not to ask questions of Mappoint.

  Mappoint forum is here: http://social.microsoft.com/Forums/en-US/streetsandtrips/threads

• I live in Germany where - almost all of the computers on the market have windows installed in German. Is it possible to buy a laptop with MS vista in German installation and when I update, I upgrade to the English version of Windows 7?

  I live in Germany where - almost all of the computers on the market have windows installed in German. Is it possible to buy a laptop with MS vista in German installation and when I update, I upgrade to the English version of Windows 7?

  How your question about Windows Update?

  The answer to your question is Yes, if you buy Vista Ultimate or business and move to Win7 Ultimate or business.

  Specific Win7 forums include http://social.answers.microsoft.com/Forums/en-US/category/windows7 and http://social.technet.microsoft.com/Forums/en/category/w7itpro/

  ~ Robear Dyer (PA bear); MS MVP (that is to say, mail, security, Windows & Update Services) since 2002. DISCLAIMER: I do not represent nor don't work for Microsoft

• During the installation and activation of google chrome, I lost my taskbar

  Original title: Google Chrome

  during the installation and activation of google chrome, I lost my taskbar. How can I reinstall my taskbar?

  Hi Frank,.

  1. do you receive any error messages?

  2. have you restarted the computer once installed google chrome?

  3. not this problem occurs when you run a specific program or out of order?

  This problem can occur for the following reasons:

  • Auto-hide the taskbar has been selected for the taskbar and Start Menu Properties.
  • Your user account settings are corrupt.

  Method 1: Make sure that the hide option automatically is not selected for the taskbar

  To determine if the hide option automatically is not enabled for the taskbar and Start Menu properties, follow these steps:

  a. press CTRL + ESC.

  b. If the Start menu is displayed, click on the Start menu and then click Properties.

  c. click on the task bar , clear the Auto-hide the taskbar option and then click OK.

  If the problem persists, you can proceed to method 2.

  2 method: Recycle Explorer.exe

  Try to recycle Explorer.exe by opening the Task Manager (you can use Ctrl + Shift + Esc), selecting explorer.exe in the list and choosing end process.

  Now go to the file menu, choose new task and type in Explorer in the Open box. Press on enter and explore should restart itself.

  Check whether the taskbar is visible now.

  Hope this information helps. Provide more information so that we can help you.

• Professional Windows does not see my hard drive during installation and wants to leave the installer.

  installed the new hard drive in my compaq lap top, started the professional windows installation and stops because it cannot find the hard drive. It is in the bios and has passed the tests. My lap top has only a cd/dvd drive, a floppy drive. Not knowing what to do.

  It is probably because you have a hard drive Serial ATA (SATA) in your computer.  These drives did not exist when Windows XP came out and so no drivers for this type of disc can be found in a regular Windows XP don't install.  Windows makes allowances for that by inviting you to press the "F6" key at the beginning of the installation process, but then you must provide the SATA drivers diskette (no other medium will do).

  "Limited OEM driver support is available with F6 during installation of Windows XP and Windows Server 2003"
    <>http://support.Microsoft.com/kb/314859 >

  There, several articles that explain how to install XP on a SATA drive without needing a disk.  Here are a couple of them:

  "Installing Windows XP with AHCI/RAID F6 of USB drivers only"
    <>http://www.Prime-expert.com/articles/B02/installing-Windows-XP-with-F6-AHCI-RAID-drivers-from-USB-only.php >

  "How to install XP on a SATA HARD drive without a floppy for a laptop drive"
    <>http://www.ehow.com/how_7395338_install-HDD-floppy-drive-notebook.html >

  HTH,
  JW

• I have windows xp and whenever I click on Installer Windows icon comes out and says it: preparation for the installation and it takes a while to come

  I have windows xp and whenever I click on an installer of winows icon comes out and says it: preparation for the installation and it takes a while to come

  Hi DanBourque

   

  1 does the problem occur when you click the icon of the exe file or any application shortcut icon as well?
  2. for how long have you been faced with this problem?

  3. did you of recent changes on the computer?

   

  You can re-register Windows Installer and check if this helps-
  a. Quit all Windows programs.
  b. click Start, click run, type msiexec /Unregister in the Open box and then click OK.
  c. click Start, click run, type msiexec/regserver in the Open box and then click OK.
  d. restart your computer.

  I hope this helps.

• My laptop under windows Xp service pk 3... Windows Update keeps trying to download Update KB 2416447 Secuirty but never, it installs and does not

  Windows Update keeps trying to download Update KB 2416447 Secuirty but never, it installs and does not

  Hello Roy Green,

  Thanks for your post.  Take a look at this thread for a possible solution to your problem.  Please let us know if it did or did not help to resolve this problem.

  See you soon

• I can't get updates since SP2 installation and update of the Windows Update Agent.

  I have Vista Home Premium 64-bit.  I have done 3 installs clean for several days and each time I install SP2 and update the Windows Update Agent I can't get updates.  When I click search for updates, it just keeps looking for hours and hours and never stops looking.  I tried several solutions on the internet, including those found here.  Of course, the first thing I did was run the Fixit of Windows Update tool.  He could not solve any problems found.  He gave the error code 0 x 80070005.  I installed the SubInAcl.exe and run several different command text and a text of the batch.  The batch text did nothing.  The texts of order had errors of syntax and a file, he could not access.  I ran the System File Checker, and it finds errors, it could not fix.  I just did a clean install on this machine 6 or 8 months ago because I was going to get rid of the computer, so when I put in place I used the username user.  I came across no problem at all when I installed the operating system and update everything.  Since then, I decided to keep the computer, so I wanted to have it in my name.  As I said, this is my 3rd try.  I am willing to give.  Maybe someone here can help.

  I tried two clean installs and I get the same thing.  Once I have installed SP2 and the new Agent update, I can't get more updates.  It keeps only the search for hours without results or error messages.  I tried all of the suggestions I found on the internet, but nothing works.  I get always the same error code 0x80070005, when I run the Fixit of Windows Update tool.  There must be a way to solve this problem.  Why I was able to do a clean install of 6 or 8 months without any problems, but now I can't.  It makes no sense at all.  I really hope someone who knows the answer reads this.

  Ralph C.

  I finally got it!  I tried two other proposed solutions, then I ran the System File Checker, which is no problem, then I ran Check Disk.  Check disk found and repaired files in the file system of BITS among others.  After that, I'm now completely up to date with Windows Update.  I was ready to give up.  I'm glad I did not.  For anyone else having similar problems, don't give up, the answer is there.

  Ralph C.

• Windows vista is 63 92 updated installation and after running for seven hours must be stuck in a loop. How to regain control of my everex computer

  Windows vista is 63 92 updated installation and after running for seven hours must be stuck in a loop. How to regain control of my everex computer

  Hello

  1. have there been recent changes to the system before the show?

  2 is the issue limited to the installation of Windows updates?

  3. do you have security software installed on your system?

  Method:

  Follow the indicated link and perform the steps and check if it helps fix the problem.

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

  http://support.Microsoft.com/kb/949358

  Note: It is strongly recommended that you back up all your personal files. For more information about how to back up your files, please visit: http://windows.microsoft.com/en-US/windows7/Back-up-your-files

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  Let us know if it helps.

• I need to install Silverlight, but when I download the installer and run it, it tell me that 'your operating system does not support the 64-bit version of Silverlight.

  Silverlight installation problems

  I need to install Silverlight, but when I download the installer and run it, it tell me that 'your operating system does not support the 64-bit version of Silverlight. I have Vista Ultimate, a 64-bit system.  Help, please.

  Hello

  It's the operating system Vista Installation Forum.

  Microsoft has set up Forums to specifically to questions of Silverlight.

  They should be able to help you there.

  http://forums.Silverlight.NET/

  See you soon.

• I have problems installation and update, get the error 641

  I have installation and update problems to continue to receive code 641 please help

  Hi ByrdyRidgley,

  Follow the troubleshooting steps in this thread with the same error code 641.

  Let us know if that helps.

• After uninstalling printer Windows Installer and Microsoft Office error "this update package not could be opened"

  Original title: Windows Installer and Microsoft Office problems after you have uninstalled the printer

  I tried to install more than one printer, a HP Photosmart C4280 by downloading the drivers and updates on the HP site. I uninstalled the printer after it failed to scan a document and I had no more use for it. Then the trouble started. When I tried to open some programs (iTunes, Skype, etc.) for the first time after the uninstall of the printer, a window "Windows Installer" popped up. After you have configured Windows Installer, the program would open normally. However, when I try to open any Microsoft Office programs (Word, Excel, etc.), Windows Installer appears, but it turns into a window that reads:
  "This patch package could not be opened. Verify that the patch package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer update package. »

  Microsoft Office programs are open at all, and I desperately need my programs of Microsoft Office to work even faster. I would appreciate it if Windows Installer will stop trying to configure when I open a program also. Can someone help me please?

  Hi Jennifer7,

  It is sufficient to indicate the complete error message you receive.

  Method 1: To solve the problem of Windows Installer, follow the steps

  http://support.Microsoft.com/kb/2438651#reso1

  Method 2: Follow the steps mentioned in the article below which addresses Office question

  You receive an error message when you try to install or run an Office program: "this patch package could not be opened" or "" the installation source for the product is not available".

  http://support.Microsoft.com/kb/932857

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

  If the question of the Office has not changed, you can post your request in the Office forums for more specialized help.

  Office forums

  http://answers.Microsoft.com/en-us/Office/Forum/office_install?page=1