Installation of 10.2.0.1 on Linux RHEL 5.2 64 bit
HelloDuring installation, checks pre - req failed with the error below.
Actual result: redhat enterprise Linux Enterprise Linux Server release 5.2 (Carthage)
Full version. The result of this review is: failure of < < < <
Problem: Oracle Database 10 g is not certified on the current operating system.
Recommendation: Make sure that you install the software on the correct platform.
According to the m note requirements for install Oracle10gR2 on RHEL 5/OEL 5 (x86_64) [421308.1 ID], I installed all the packages needed.
From metalink note master Note of the requirements of the Linux operating system for database server [851598.1 ID], RHEL 5 64-bit is supported for 10 gr 2.
But here what is the problem?
Thank you
Kouadio
PL see 10gr 2 Release Notes for Linux x 86-64 instructions - http://download.oracle.com/docs/cd/B19306_01/relnotes.102/b15666/toc.htm#CJAFHGHG
HTH
Srini
Tags: Database
Similar Questions
-
I'm under vm workstation 10.0.1 on Windows 7 Ultimate 64 bit, I created a VMware machine in my computer using Media 6.4 RHEL, after all, installation has been completed successfully, The RHEL installation wizard suggested to restart, after restart, the virtual machine shows BLACK SCREEN WITH CURSOR of A in the upper left. FYI my system supports the "virtualization technology intel. Please help, if someone solved this issue. Thank you.
Thanks for help.
The problem has been resolved. As I said I was installing OS and then the problem comes after the reboot.
I selected all the graphics software during the installation of linux. and it worked.
-
Hello
Hello, I am a little lost. I bought a T440S a few months ago. When I bought it, I tried to install a distribution: linux debian amd64 wheezy. Nevertheless, I had a lot of problems. Then, I ran Ubuntu. Today, I would like to know if I can go back to Debian or other distributions such as Mint or Fedora (64-bit versions). I need to use the identification of the finger, and I do not have a touch screen.
So, could you give me some advice, please .
I thank you and wish you a good day/evening/night (this is the night, I live in france ).
Hello
I run Fedora 20 x 64 on both my T440s and T440p in a dual-boot configuration. RHEL distributions require a bit of work, once installed as opposed to Ubuntu / Mint that require very little attention. I have no experience with the installation of Debian, so I can't comment on that.
But 20 Fedora works like a charm in all directions and the only thing that I really need to configure the ClickPad. My 440 model s is an i7 with no touchscreen FHD.
Here for info on this page:
-
NIDAQmxBase Linux RHEL 6 x86_x64 USB...
Trying to get NIDAQmxBase 3.6 w / USB support for installed on LINUX RHEL 6.3 x86_x64 WS
USB 6501 OEM,
USB-6009 OEM
running as root:
[root@NIX1 /] # mount
usbfs seems to be mounted... etc/fstab to mount it as indicated
/ dev/map/vg_nix1-lv_root on / type ext4 (rw)
proc on/proc type proc (rw)
Sysfs on/sys type sysfs (rw)
type devpts on/dev/pts devpts (rw, gid = 5, mode = 620)
tmpfs on/dev/shm type tmpfs (rw, rootcontext = "" system_ubject_r:tmpfs_t:s0 "")
usbfs/proc/bus/USB type usbfs (rw, devmode = 0666)
/ dev/sdb1 on / boot type ext4 (rw)
/ dev/map/vg_nix1-lv_home market/House type ext4 (rw)
None on/proc/sys/fs/binfmt_misc type binfmt_misc (rw)
sunrpc on/var/lib/nfs/rpc_pipefs type rpc_pipefs (rw)
/ dev/sr0 on/media/NIDAQmxBase360 type iso9660 (ro, nosuid, nodev, uhelper = udisks, uid = 500, gid = 500, iocharset = utf8, mode = 0400, dmode = 0500)lsdaq runs and complains about the firmware:
[root@NIX1 /] # / usr/local/natinst/nidaqmxbase/bin/lsdaq
--------------------------------
Detect of National Instruments DAQ devices
Find the following materials:Device error: incompatible firmware. Serial number: 01646C 23
Run
/bin/FWUpdate update. green light on USB 6501 flashes constantly
running FWUpdate compains as follows:
--------------------------------
[root@NIX1 /] # / usr/local/natinst/nidaqmxbase/bin/FWUpdate
Could not load library /usr/local/lib/liblvrt.so.12.0
libXinerama.so.1: cannot open shared object file: no such file or directory
To download the engine Runtime of LabVIEW, go to http://www.ni.com/rteFinder?dest=lvrte&version=12.0&platform=Linux&lang=enlocation of /usr/local/lib/liblvrt.sa.12.0 reports:
[root@NIX1 /] # locate liblvrt.so.12.0
/usr/local/lib/liblvrt.so.12.0
/usr/local/lib/LabVIEW-2012/liblvrt.so.12.0.0STAT to file reports:
[root@NIX1 /] # stat /usr/local/lib/liblvrt.so.12.0
File: ' / usr/local/lib/liblvrt.so.12.0'-> 'LabVIEW-2012/liblvrt.so.12.0.0 '.
Size: 30 blocks: 0 IO block: 4096 symlink
Feature: fd00h / 64768d Inode: 131699 links: 1
Access: (0777/lrwxrwxrwx) Uid: (0 / root) Gid: (0 / root)
Access: 2012-10-22 14:27:59.858557301-0400
Change: 2012-10-22 14:27:59.813443661-0400
Change: 2012-10-22 14:27:59.813443661-0400NIDAQmxBase 3.6 installs VISA and 'C' interface via. \INSTALL, reports success, seems normal.
cannot run lsdaq, FWUpdate or anything like that on the Menu of Applications National Instruments (NI-VISA submenu, OR Trace of IO.)
My guess is that the permissions are always watered.
Solved and was able to update the firmware.
Well explained here... http://digital.NI.com/public.nsf/allkb/93C92D41B25341B286257A4D007BACB8
and here's how-useful. http://h10025.www1.HP.com/ewfrf/wc/document?CC=CA&DLC=en&docName=c01769573&LC=en
-
Compatible Linux RHEL (Linux Red Hat Enterprise Server 6.7) for oracle database 11.2.0.4 with grid Infrastructure.
Hi all
We plan to patch Linux Redhat Enterprise Server (6.4 and 6.5) to 6.7.
I tried Searchin' on support of oracle for the compatibility of the database for Linux patches, but not able to find accurate information.
can anyone share the ID document or information related to it.
If OS RHEL 6 update 4 to 6-7 update patch
(1) is it compatible
(2) bugs or problems reported
(3) in addition to the binary link again than the DBA to perform any other
Thank you
Hello
6.7 RHEL is certified for the database 11.2.0.3 or newer. In other words, it is certified for RHEL 6.7 11.2.0.4
Certification information for the Oracle database on Linux x 86-64 (Doc ID 1304727.1)
-Jonathan Rolland
-
Creating a Cluster of Linux RHEL on vSphere 5
Hello
Is it possible to linux RHEL VMs on ESXi V5 hosts vSphere cluster?
I have a few RDMs I can add 1 VM, but they are not visible to add them to the other virtual computer. These ROW are the shared storage using two virtual machines in an active/passive cluster with RHEL.
Windows clusters seem to work out of the box there is some advanced configuration settings, I need to add first?
Thank you
Hello
The reason is that, by default, storage filters are enabled (see storage filters - yellow brick for more information).
To allow VMS access a raw disk, even through the RDM, you must disable the ROW filter. To do this, refer to VMware KB: LUN mechanism creating filtering RDM .
I hope this helps.
-
17 Firefox under Linux with Linux installations on separate partitions, with a repertoire common/home its "own partition.
I would like the json files to appear only on the / Home partition and each instance of Firefox to read and write files json here only
Hello
One way would be to start the Firefox Profile Manager in each Linux instance and that it points to a profile of another Firefox installation folder, preferably one that has been customized in a satisfactory manner. You can then delete the profile by default in every Linux installation.
-
Hi all
I'm looking for full installation GUIDE for Oracle Business Intelligence Data Warehouse Console Administration 11 g and Informatica PowerCenter and PowerConnect 9.6.1 for Linux x 86 (64 bit) adapters. I just wonder is there any url that you can recommend for installation. Please advise.
Looks like these are ask you.
http://docs.Oracle.com/CD/E25054_01/fusionapps.1111/e16814/postinstsetup.htm
http://ashrutp.blogspot.com.by/2014/01/Informatica-PowerCenter-and.html
-
Maybe it's because my lack of familiarity with the Linux syntax.
I installed the JDK as instructed in the SQLDeveloper release notes for Linux x 64
I downloaded SQLDeveloper in its own folder and sailed there in the command line
[root@localhost sqldeveloper] # ls
sqldeveloper - 3.1.07.42 - 1.noarch.rpm
I then copied and run the following command exactly as in the SQLDeveloper installation instructions download
[root@localhost sqldeveloper] # rpm - Uhv sqldeveloper - 3.1.07.42 - 1.noarch.rpm
sqldeveloper - 3.1.07.42 - 1.noarch.rpm: not an rpm package (or the package manifest):
That is what it is? Any help welcome.
Published by: Peter Hartgerink on 13 June 2012 13:45Perhaps there was an error in the download. I don't see any checksum that you can use to validate the file.
You can try to download the file again. Keep the existing file so that you can compare the two versions uploaded to see if they match.
You can also try some of the other RPM commands on the package to see if they recognize as a file valid RPM.
-
Installation of Oracle 11 g R2 on Linux itanium ia64
Dear all
I found difficulties in installing Oracle 11 g R2 on Linux itanium (ia64 RHEL 5.2), earlier that I had installed the oracle 10 g on the same platform with the help of the path, but I could not find the patch for 11 g R2, help me for the installation of the product.Shayad says:
Earlier when the oracle 10g R2 itanium was not running, oracle 10 g 2 were installed with the help of the path, beJust because you did with 10g does not mean that you will be able to do it with 11g.
I assume that by 'path' you mean 'patch '.
in this case, we first of all install the path that has jre, after that, we run runistaller for the flexible database.
so pls tell me which path we need for the same thing.What makes you think that such a 'path' ('patch'?) exists? Please visit http://www.oracle.com/us/corporate/press/346696
I would say that your 11g on itanium Setup project must be reviewed.
-
HRMS installation on a VISION on Linux RHEL 5 12.1.1
Ive tried to find information about how to install human resources, payroll and SSHRC on vision.
With this script, I get
SQL > select substr (inst.application_id, 1, 10) 'App ID. "
2 substr (tl.application_name, 1, 45) "App name"
3. decode (inst.status, 'I', 'Installed', 'No,' Not installed ',)
4', 'Shared', 'L', 'Custom') 'status '.
5 FND_PRODUCT_INSTALLATIONS inst,
6 FND_APPLICATION_TL tl
7 where inst.application_id = tl.application_id
8 and tl.application_id as 80%.
9 order of inst.status;
The application ID
----------------------------------------
Name of the application
--------------------------------------------------------------------------------
Status
-------------
800
Human resources
Not installed
801
Payroll
Not installed
The application ID
----------------------------------------
Name of the application
--------------------------------------------------------------------------------
Status
-------------
802
FastFormula
Not installed
809
Time and Labor engine
The application ID
----------------------------------------
Name of the application
--------------------------------------------------------------------------------
Status
-------------
Not installed
804
PS3
Not installed
808
The application ID
----------------------------------------
Name of the application
--------------------------------------------------------------------------------
Status
-------------
Time and work
Not installed
805
Benefits advanced
Not installed
The application ID
----------------------------------------
Name of the application
--------------------------------------------------------------------------------
Status
-------------
803
DateTrack
Not installed
8 selected lines.
Can someone give me please the relevant steps/patches/metalink notes installation of HRMS? Thank you guys.Hello
Have you installed a demonstration of vision database? The application, click Help > about to get the name of the database.
The installation steps and the pre - req can be found in (Note: 761564.1 - Installation of Oracle Applications and upgrade 12 Release Notes (12.1.1) for Linux x 86).
Thank you
Hussein -
Error during installation of the repository of BPA on LINUX
based on DOC-ID 554528.1
I did following steps:
-installed Database 10g on Linux Enterprise.
-created a new database with UTF-8 character set
-created two tablespaces ARISDATA, ARISINDEX (2GB)
-runs the aris70.sh script
-created the new schema
Installation of BPA on LINUX repository
-If I run install_bpr10.1.3.4271679.sh following error occurs:
tail: cannont open "+ 182' for reading: no such file or directory".
3158 records + 0 in
records of 3158 + 0 out
3158 (3.2 KB) copied, 0,115841 seconds, 27.3 kB/s
gzip: stdin: not in gzip format
. / install_bpr10.1.3.4271679.sh: line 173: /tmp/_install.3889/configure.sh: no such directory
Published by: user10191651 on May 18, 2009 04:31RedHat 5.X / OEL 5.X is not certified.
Please check the link below certification.
http://www.Oracle.com/technology/products/BPA/index.html
http://www.Oracle.com/technology/products/BPA/bpa_certification%20Matrix.xlsNote: RHEL 4.0 (64) is the Certified version.
See you soon,.
Vish -
Installation guide for Oracle 10 g on Linux
Hi all
Can anyone provide me please with steps or some in 10g Linux installation guide.
Thank you
AnchorageI'm really surprised, given a lot of answers, but none of them point you the Oracle documentation, however, it is purely a matter of doc. If you follow the doc below, it should be perfectly correct:
[Database Release Notes 10 g Release 2 (10.2) for Linux x 86 | http://download.oracle.com/docs/cd/B19306_01/relnotes.102/b15659/toc.htm]
[Database Installation Guide 10 g Release 2 (10.2) for Linux x 86 | http://download.oracle.com/docs/cd/B19306_01/install.102/b15660/toc.htm]Nicolas.
-
Installation of VM Player using script on Linux
Everyone installed VM Player automatically using a script under Linux before? If so, how?
Exactly that!
-
Error in the installation of Oracle 10 g RDBMS on linux installed on Vmware
Hello
I try to install the software of RDBMS Oracle 10 g. I created all the required users and groups, creates directories and updaates the sysctl.conf file.
When I run the installation program. / runInstaller it gives the following error.
[data oracle@aasim] $. / runInstaller
From Oracle Universal Installer...
Checking Installer requirements...
Checking the operating system version: must be redhat-3, 9-SuSE, redhat-4, UnitedLinux - 1.0, asianux-1 or asianux-2
Past
Met the requirements of the installation program.
Preparations for the launch of Oracle Universal Installer from/tmp/OraInstall2011-02-26_11-48-44 PM. Please wait... [data oracle@aasim] $ Xlib: connection to ": 0.0" refused by server
Xlib: No protocol specified
Exception in thread "main" java.lang.InternalError: can't connect to X 11 window server using ': 0.0' as the value of the DISPLAY variable.
at sun.awt.X11GraphicsEnvironment.initDisplay (Native Method)
to sun.awt.X11GraphicsEnvironment. < clinit >(Unknown Source)
at java.lang.Class.forName0 (Native Method)
at java.lang.Class.forName (unknown Source)
at java.awt.GraphicsEnvironment.getLocalGraphicsEnvironment (unknown Source)
at java.awt.Window.init (unknown Source)
java.awt.Window. < init >(Unknown Source)
in java.awt.Frame. < init >(Unknown Source)
to oracle.ewt.popup.PopupFrame. < init >(Unknown Source)
to oracle.ewt.lwAWT.BufferedFrame. < init >(Unknown Source)
to oracle.sysman.oio.oioc.OiocOneClickInstaller. < init > (OiocOneClickInstaller.java:378)
at oracle.sysman.oio.oioc.OiocOneClickInstaller.main(OiocOneClickInstaller.java:2091)
Can someone tell me why I get this error and how to solve it.
Thank you
IsabelleSalvation;
If you do install on machine wmware than as root cause is
xhost +.
If you are installing on via puty you will need to use a program like vncviwer, xming etc.
Please check my previous post
http://KR.forums.Oracle.com/forums/thread.jspa?threadID=1630832
Respect of
HELIOS
Maybe you are looking for
-
Default e-mail application is not responding
I accidentally deleted some files which are necessary for the mail app Apple run on my MacBook. I'm currently under OS X El Capitan. For weeks, every time I open messages, the icon bounces up and down, and then it gives me this error: I can always re
-
Codes sound satellite 1900-303
I have a 1900-S303 Satellite that has a broken screen. The hard drive and ram have been removed by the previous owner. If I turn on the laptop it gives 3 long beeps and does not appear on an external monitor. My question is what is the meaning of the
-
HP Pavilion a6710t: HP pavilions NVIDIA a6710t drivers
I'm looking for the correct NVIDIA driver upgraded to the windows 7 32-bit home version. I searched here and also including the NVIDIA site without a clear answser. Thank you - Pete
-
Fireware failure and Gone Wireless update
Hey all,. Summer faced with my Android phone for a few hours trying to configure the Wifi when I arrived to try to update the firmware. I got the correct version for my router (WRT54G v.6) but when I started immediately I got the message "upgrades ar
-
imageres.dll missing in system32
a friend of mine deleted imageres.dll in system32 He told me and I found it After I try to move again my computer beeps and dosent move the file Help, please! I can't run some programs and Control Panel running: hp (vista Basic) : (when I downloaded