Interact with ssh session?

Similar Questions

• N3048 cannot leave ssh sessions with firmware 6.3.0.3

  I recently updated a stand-alone switch N3048 for the latest firmware 6.3.0.3, A14 (filename = N3000_N2000v6.3.0.3.stk) 6.2.7.2, A10 and it seems, I can't leave a SSH session to the switch (via the OOB interface). I can connect with several configured users and the switch works fine otherwise, but from entering exit the SSH session is suspended. It looks like the following on a switch with m1940 hostname:

  M1940 #exit
  M1940 > output<-- hangs="" here,="" not="" even="" a="" newline="" after="" hitting="">

  Connecting to the switch via the serial console, I see that 'show ip ssh' is empty and shows no active sessions. In addition, the switch generates the message "User has disconnected" in syslog. However, the real SSH session of my management station is still alive, and actually living remains permanently it seems. I left such a session open all night after the * IDLE TIMEOUT * had it done automatically on the switch and the next morning, the SSH session and underlying session TCP were always persistent.

  After reloading via the serial console switch the SSH session disconnect properly by following a generic box of RHEL 6 on my management station:

  M1940 connection closed by remote host.
  Closed connection to m1940.

  For me, it's just a further indication that the SSH session remains active after a user, there are sessions on the switch.

  Also has anyone seen this behavior? Someone at - it a data point of SSH sessions behaving normally with this new firmware?

  Your observations are correct, that Dell Networking OS 6.3.0.3 is no longer available for download from the Dell eSupport site. If you have all of the switches currently on 6.3.0.3, I suggest rolling back to 6.2.7.2.

  I don't have any official information from Dell on the exact reason the firmware was pulled. But according to my observations, it seems that there are certain undesirable behaviors in the version of the firmware. Including those discussed here on the forums. Rather than wait for the next firmware correct these behaviors, the firmware is shot, quickly being developed and should hopefully be reissued in due course.

• SSH session with QNX momentics-&gt; cannot run - permission denied

  Hello everyone I am new to this world to develop a blackberry and I have a question about ssh, it can be quite simple, but a simple tip could save me from going crazy.

  When I open an ssh session with my blackberry and try to execute statements such as ping, it is said:

  Ping $
  SH: ping: cannot run - permission denied

  So my question is: is there a way to access these permissions and run the command?

  I use qnx momentics, a real device and access the ssh by qnx momentics option launch a ssh session.

  I'd appreciate any advice or tips or whatever it is that one can say to help me, thanks in advance

  When you connect via SSH, logged as "devuser". This user has limited permissions... basically these permissions that would be a regular application.

  To run the 'ping', you need a higher level of access. (Check permissions and ownership with "ls-l/usr/bin/ping") This isn't an option, so the answer is no, there is no way to do it.

• Interact with a CGI web page

  Greetings OR Forums,

  I am developing a telescope pointing control system that needs data ephemerides generated from a Jet Propulsion Laboratory web site:

  http://SSD.jpl.NASA.gov/horizons.cgi

  The main interface of their horizons system is via Telnet which is precarious and is no longer supported by LabVIEW.  I was hoping that someone could advise me on how to start using LabVIEW to interact with the web page of cgi based at the above address.  If I can do it, I can retrieve the necessary ephemeris data and analyze inside LabVIEW using the commands of the base string.

  Is there a kit of basic tools that you can point me to interact with web pages or any code sample?

  Thank you
  Scott

  High Altitude Observatory

  Boulder, CO

  Use screws of HTTP Client:

  

  VI GET is the standard demand 'give me this web page' - give it the URL of your ephemeris data session and the release of 'body' will give you the web page content - if you use the raw text of output, then this should make analysis easier chain (without tags html etc..).

  (In addition, you can use Telnet in LabVIEW, it is not a library group for her more - you should be able to use the TCP screws to roll and you can also if interface with other libraries/applications Telnet for example PuTTy... it might even be something in .NET)

• VPN configuration ends the SSH session

  Can someone tell me why my SSH session in a PIX gets terminated when I apply a command card crypto on the firewall that I can access?

  If you go through the external interface, you will need to be very careful about adding crypto map controls, cause, you can easily lock you out of the PIX and stop the PIX to pass all traffic.

  If there is an existing encryption card on the PIX and you add another, you must unapply the card encryption first, add the new in (make sure it is complete) and then re-apply.

  If there is no existing mapping, then make sure that you add the card encryption in its entirety, including the access list and then apply the encryption card to the interface.

  If you think you're doing it right, answer back with exactly what you type in and let's see what you're missing.

• SSH Session in the firewall log errors

  Cisco NIDS 4210 connected to 515UR PIX for fleeing host.

  Loss of connectivity between the two briefly and when the link is back to the top I see now what follows in firewall logs:

  SSH session (address IP of NESTS) on the inside for the user interface ' ' disconnected by the SSH server, reason: "Connection closed TCP" (0x03)

  These inscriptions are spend on all the 1 second.

  Suggestions?

  You do everything correctly; However, I forgot the most obvious thing!

  Some of the improvements PIX cause the SSH host key change. You trust the old key, but now the key has changed, so that the sensor plugs is no longer.

  Here is how you confirm this and correct. Assume 10.1.2.3 is the IP address of your PIX:

  Log in to the CLI IDS and run the following commands:

  probe # configure terminal

  Service sshKnownHosts Sensor (config) #.

  view the settings of Sensor(config-SshKnownHosts) #.

  rsa1Keys (min: 0, max: 500, current: 1).

  -----------------------------------------------

  ID: 10.1.2.3

  Exhibitor: 35

  Length: 1024

  modulus: 149179708427081921991314663521689741774756100495017439492530949884845471909428674644441439921263665830148866033670908370886898363392278142692283773831284783749668258827076536253701577307251585007783348971708045285375623731521532280202472737775552590541493491501955424294561124918251835488802734947343216844023

  -----------------------------------------------

  -----------------------------------------------

  Sensor(config-SshKnownHosts) # no id rsa1Keys 10.1.2.3

  output Sensor(config-SshKnownHosts) #.

  Sensor (config) # ssh - host key 10.1.2.3

  Fingerprint MD5 is A7:CF:FD:02:C0:A1:C9:10:64:A8:CD:4 A: BA:0E:C1:6 B

  Bubble Babble is xobal-vemyn-tasyn-rimef-nibiv-bodig-dylel-bekat-nacel-tupip-cuxix

  You want to add to the host known for this host table? [Yes]:

  exit Sensor (config) #.

  In this example, we see that the sensor has a key for 10.1.2.3, we removed, then re-confidence that host.

  After you approve that the new PIX ssh host key, the sensor must be able to establish a connection with the PIX and start it management.

• SSH session gets ACCESS denied

  Try to connect to a Putty session and I get access denied for the ROOT user and any other user.  I can connect to this host with the VI client and create a new user, but the user also gets access denied.  I can connect via web browser and simply not the SSH session.  I'm unable to connect to the console from the keyboard is unplugged.  Are there other options before that I have to restart?  Any help is appreicated.

  Have a look here, to allow ROOT to log in: http://itknowledgeexchange.techtarget.com/virtualization-pro/how-to-allow-the-root-user-to-login-to-vmware-esx-server-with-ssh/

  Also ensure that server SSH is running:

  service sshd status
  

  If this is not the case, start it:

  service sshd start
  

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  VMware Code Central - Scripts/code samples for developers and administrators

  http://Twitter.com/lamw

  If you find this information useful, please give points to "correct" or "useful".

• Loaded with FF on laptop (Win 8), why is there no way to interact with it?

  FF loaded on my new laptop using Windows doesn't have a toolbar to allow me to interact with him. What can I do about this problem?

  East - the normal Windows 8, no RT?

  If you don't see any of the regular bars (e.g., tab, toolbar, toolbar bookmarks bar), your Firefox can be full-screen mode. The F11 function key toggles between the normal modes and full screen.

  If you have a tab bar, you can right click on an empty area of it or click New tab (+) and select missing toolbars from the menu that appears.

  A little luck?

• Able to interact with a Panel before the remote cRIO to a computer, but not another

  I have a cRIO application that publishes a remote façade for the monitoring and control of the application. A PC (Win7 & firefox), I can see, interact and control the cRIO through published remote façade. A second PC, also Win7, I can see and monitor the status of the cRIO, but no interaction does not control remote that opens and it's true that I use IE, FF or Chrome as a browser. When a PC is connected to the cRIO, via a dedicated Ethernet connection and only the cRIO and PC are on this network. For this private network of two devices, the PC is always the address 192.168.1.1 while the cRIO always use 192.168.84.199 (port 8000).

  The rules of firewall on both computers are configured to allow all inbound and outbound programs/ports/protocols to be used between these two IP addresses.

  Two PC's have development systems LabVIEW to update installed on it (which more or less guarantees that they have the minimum requirement LV of execution necessary to see and use a remote façade).

  What may be different on the PC who discovers, but cannot interact with the remote control?

  Right-click on the second, and then select "take control of this VI.

  As far I know - that a viewer of the remote façade can control the frame at any time - the rest cannot display.

• How can I interact with mainvis and subvis without closing any of them?

  I have a mainVI which opens a Subvi perfectly and I m using the "VI Open reference' & the 'node of reference VI to call' to run the Subvi. However, once I open the Subvi and it s running, I can´t do something with the mainVI. The only way to interact with the mainVI new it s closing the Subvi, I want Don t that happens because I need the two work together and interact with both at the same time.

  Is someone can help me?

  Thank you

  Make sure that the property of Subvi is not floating or modalvalue.

  (Properties of VI... appearance of windows...... customize the behavior of windows)

• Microsoft 3000 wireless keyboards; they will interact with each other

  I have 2 PC and I would like to replace the wired keyboards for 2 sets of Microsoft 3000 keyboard, will they interact with each other and can I change Ch / Freq of the units

  Hi Baz,

  Each keyboard has different frequency and will not interact with each other.

• problem caused this blocking the program interact with Windows

  I got this message "a problem caused this program blocking interact with Windows" when I m access share foder in Windows xp

  Hello

  ·         You have made no changes to the computer until the problem occurred?

  Method 1:

  I suggest you to check for the problem in safe mode, follow the link below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:

  You can also put your computer to boot and find the faulty program that is causing the problem by following the link below.

  http://support.Microsoft.com/kb/929135

  Note: Make sure you put the computer in normal mode by following step 7 after that solve you the problem.

  Method 3:

  You can also check the observer event log to check which program is causing the problem. Check in the event viewer, follow the link below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer

• Windows Mail is not interacting with the server.

  When Windows Mail (WM) is open, it will download 2 of each incoming e-mail.  Conducted a comprehensive analysis of the system, no problem.  Talked with our server provider, we ran the test emails to see if WM was interacting with the server and it is not.  Is also not to keep my ID and password to log on the server. Y at - it an update I missed it to avoid these problems?

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  It causes a frequent there have new antivirus scan program messages.  Uninstall your AV program and reinstall without any mail analysis feature.  You will be just as safe.

  Another common cause is to have two e-mail accounts, referring to the same mailbox.  The send/receive operation can access two accounts at the same time and both can download the message even if they both refer to the same mailbox. Brian Tillman [MVP-Outlook]

• OS 10.3 / WebView: no interaction with the Google Maps Javascript API

  Hello

  Google Maps Javascript API no longer works correctly using the Web on OS 10.3.  On all the operating system previous releases everything worked perfectly fine in WebView but on OS 10.3 even if the plan (or view, or anything else provided by Google APIs) is displayed correctly, there is no interaction whatsoever with it - no response to taps, none is panoramic, no zoom, etc.

  I don't speak of the 10.3.0.698 Simulator - I do not have access to the true OS 10.3 device.

  Even simple examples of Google Maps doesn't work, try for example:

  import bb.cascades 1.2
  
  Page {
      Container {
          preferredHeight: 720
          preferredWidth: 720
          WebView {
              preferredHeight: 720
              preferredWidth: 720
  
  url: "https://google-developers.appspot.com/maps/documentation/javascript/examples/full/marker-simple"
          }
      }
  }
  

  The map appears, but there is absolutely no interaction with it - just a STATIC content.  On OS 10.2.xxxx, it works perfectly fine...

  P.S. If you open the same example URL directly in the web browser on OS 10.3 everything works well - responds to taps, she can be zoomed, panned, etc..    So, it's apparently a problem with user agent (which is probably the same web browser both webview).  Change the user agent in WebView to e.g. Z10 user agent doesn't help, either.

  Can anyone help?

  Your sample application does not seem to suffer the original bug, I thought. That bug could cause a WebView with no ancestor ScrollView would get too small window Visual and tactile input would be anchored to the Visual display window very small. If you want to learn more on this topic, see a tale of two windows - part for the discussion of Visual and updated display on the page. Perhaps your sample application it is OK because it specifies a preferredHeight for Web display, which can affect the used Visual display window.

  To be more precise, on a real device of passport BlackBerry running OS versions 10.3.0.1052 and 10.3.0.1154, the sample you provided responds perfectly to press ENTER.

  However, on the Simulator on OS 10.3.0.698, I can confirm input touchscreen does not work. Therefore a separate bug, which seems to be specific to the Simulator.

  I think you can be assured that end users will still be able to use your app (s) on a real passport of BlackBerry device, but it is unfortunate that it does not work on the Simulator.

• BB10 - interaction with a childwindow

  Hi all

  I have a child with interaction with a window problem.

  I developed an application with phonegap (2.7.0) and I'm trying to make a paypal payment in my application.

  This requires to open a child window to display the connection at Paypal and after checking paypal redirect me to what I want.

  My problem is that I have no way of knowing if the transaction is completed and when to close the window.
  Ideally, I would like to read the url inside the childwindow to act accordingly, but once I opened my window, I can't do anything in it.

  So here is my appeal:

  childwindow = window.open('https://www.sandbox.paypal.com/webscr?cmd=_express-checkout-mobile&token='+token, '_blank');
  

  My childwindow object contains managers of loadstart, loadstop and output.

  I suspect that the inAppBrowser of phonegap is just useless and prevents me from using the childbrowser good webworks.

  Anyone had this problem before?

  Thank you

  Hi Erik, thanks for your response.

  I finally solved my problem: the new phonegap feature inAppBrowser.

  Since Cordoba 2.3.0 introduced a childBrowser based on one of the previous plugins. Problem is that if it works pretty well on Android and iOS, they have not spent time at all on Blackberry, I would say. Their instance replace the webworks one, but on this one, you cannot run any code in the child window, so no way of knowing the location currently.

  I disassembled this inAppBrowser in the Cordoba code relief on the webworks on blackberry and everything is okay now: finally access the location.href and use a setInterval to close the window after redirect as suggested by Erik.

  Hope this will help people to this question too.