Interfacing with amp power freestyle 'mmz09312bt1 '!

Similar Questions

• Encoder interfaced with NOR-9401

  I bought a coder who has open collector and resistance to pull-up 3.3 kohm (TTL) logic output.

  The encoder comes with four sons: power + 5V, GND, channel A and channel B. channel A and B are logic output.

  Channel A and B are connected to the OID of NOR-9401 which is mounted on the cRIO.

  A standard VI for encoder counting is used and compiled under the FPGA environment.

  During the measurement, I have observed that there are number of significant loss in both directions encoder.

  I don't think that there is a problem with VI like I used it several times on the encoders with output RS422.

  Is there a problem with my current encoder with respect to its electrical interface with NOR-9401?

  Thank you.

  I don't think that there is a problem with pull-up resistance. Even if the digital IO ports have their own resistance to pull-up (usually of the order of 4.7kOhm - should be included in the manual), the power to be handled by the circuit of encoder output transistor is about 2mA. -Check your configuration for a correct connection GND. You must connect the encoder directly power GND to DGND to the printed circuit board Terminal.

• I use pci-6221, I need her to interface with thermocouple with voltage up to 5v

  I use as my pci-6221 or data acquisition card and card 8.2.this labview version gives the constant 10.5 volt signal in at the entrance to analog channel AO on pin 68 and 34. why it shows 10.5 although I did not connect any input.i use type k thermocouple and after signal conditioning with tl0804 I need it interface with AI 0.i channel unaware aware of off the road on the output pins this Card.i need to operate an electric rod that needs 24 volt DC.i give entry to the pins HAVE with variable dc power block after reaching the limit I set(eg:2v) it jumps instantly to 10.5 volts.

  You have your task to acquisition of data configured for the mode differential or asymmetric acquisition for the analog input?

  I don't understand your comment about to connect the pins WITH a DC power supply.  Why is that you connect a DC power supply to the analog input?

  Using an analog output or digital output to operate the electric rod?  I'll assume that you are looking for on/off control.  A digital output is not the voltage or current to drive something that big.  You may be able to find a relay for coil 5VDC.  Check current requirements.  With which you can have the relay to connect or disconnect a power supply of 24 VDC is the actuator.  Make sure you have a protection diode across the relay coil wired, so that the magnetic field of the coil does not damage the analog output of your card.

  Another possibility is to have the 5 VDC output transistor circuit switches the 24 VDC circuit.

• Iconia W4-820 will not charge with the power adapter USB Std

  Bought my W4 Iconia four weeks ago, a demonstration model, the last of them. It was packed in the box with a micro USB x adapter USB OTG cable and a power adapter. Back at home I discovered that the power adapter has been to Asus, possibly mixed in the shop. The prospective buyer of the Asus Tablet demo likely will get the Acer adapter. Adapter Asus with micro USB male connector works fine; specs are 5.2V - 1.35 amps; seems to be a STD USB adapter. The Asus adapter has a connector to USB female port to connect to a USB x microphone cable to USB adapter (with cable power adapter came in the box). Bought a 2nd power with USB 2 socket adapter to connect my W4 Iconia and my Garmin Zumo390 browser to an adapter. Specs are 5V - 3.5 amps.
  The Zumo works very well with the new card, but does not work my W4. Charge light stays off. USB ports switched to he Zumo and the Iconia W4, but same result. Zumo fresh, but W4 not. Borrowed another power adapter USB, 5V - 2 mines anti-personnel and new Zumo accusations, but the W4 still does not work. Also tried different USB adapter cables, but the same thing; Zumo invoice, W4 does not work.
  How is that possible? I can't tell the difference of 0.2 V between the Asus adapter and a USB adaptor STD would make the difference. But maybe I'm wrong. Wanted for adapters for the W4 Iconia and found several, but all the 5V as expected.
  Can anyone help.
  Will go to the shop again next week, but if I need an adapter V 5.2 I should order with Acer. 5.2 V adapters do exist not (readibly).

  Resolved issues. A dark and humid Sunday afternoon back to the store with the Tablet and all the bells and whistles. Changed the card Asus for the original Acer 5V - 2Amps (10W). Took the time to find the Acer adapter in the store. Demonstrated the adapter 2nd with 2 output USB ports and it wouldn't work with the Tablet W4. Tried another and found to be ok. 2 USB ports have a different power, a port for a smartphone and the other port is one tablet. Total power rating of the adapter is 17.5W (5V - 3.5Amps); some 2.5 and 1Amps. A happy man is back home again.

• Firefox v15 and up to cause my computer (MAC OSX 10.8.2) to freeze for about 30 seconds every 15 to 30 seconds and I have to turn it off with the power button

  Firefox v15 and up to cause my computer (MAC OSX 10.8.2) to freeze for about 30 seconds every 15 to 30 seconds and I have to turn it off with the power button. It this causes only after I opened Firefox, my computer works well before the opening of Firefox. I h

  It looks a little like yo maybe has a hardware problem on your computer. have you tried to repair permissions on your hard drive? create a new Firefox profile? Use the Profile Manager to create and delete profiles Firefox

• When using OS 10.11.4 after using Safari for a few minutes, the system freezes, the only way to UN - freeze is to close the system with the power switch on my Mac Pro early 2008. Any ideas?

  When you use Safari on my system Mac Pro 8 core early 2008 if will freeze with no other way to free it up it's close with the power button.  Any ideas?

  Once you can restart go immediately to disk utilities and run repair disk permissions.

  When is check your Safari to make sure you have the version appropriate for your machine.

• Problem with Toshiba Power Saver Tecra S1

  Hello

  I have problem with Toshiba Power Saver (GST).
  I installed SP2 on my WinXP Pro, and after this operation, all works well. After a few days GST on icon disappear from the task bar. When I open the Console from Toshiba, then GST I can see only incomlete standard dialog box. There is no configuration icons, but initially were, and I set all the settings. Now, there are 4 black boxes (2 small as a small icon) and 2 large as icon bigest at the bottom and a large black on the right.
  I try to reinstal GST, but it had no effect.

  Can someone help me

  Alex

  Hello Alex

  I have never seen anything like it. There is obviously some problems that doesn t allow the graphic illustration of the ATP. The first step is always reinstalling the software. I don't know what you need to do exactly. In my opinion, you should try to remove the GST and SP2. Install SP2 again and after this GST.

  If there is not the worst success solutions are preinstall the device using the recovery CD.

• Satellite L505 - new battery with more power

  Hi all

  is there another battery of the L505 with more power and a longer duration?

  Best regards
  Marcel

  Hello

  Have you ever seen the Toshiba site for compatible batteries? You can check it on the accessories homepage:
  http://EU.computers.Toshiba-Europe.com > devices & Services > PC Options & accessories

  You can get a new battery to an authorized service provider. Just call and ask them for this. ;)

• Satellite C850 lights with battery power

  Hello

  My computer toshiba laptop Satellite C850 lights with battery. It works fine when connected with AC power... !!
  When it is connected with AC power, it shows that my battery is fully charged.

  How old is the battery?
  Would it be possible that the battery does not charge more?

  My old s battery showed 100% of the fees but the farm worked only 1 min and then the battery was empty.
  This is nothing unusual, and sooner or later this would happen to any battery.

  I think you should just try a new battery compatible.

• How the interface with my RND4000?

  I'm a replacement IT here. I have almost no notes to work from, and I've never used a SIN.

  How the interface with my RND4000? I tried to put the IP address in a web browser and you get "unable to connect".

  I think the NAS is supposed to be "hosted" on one of my servers. How to determine what is the server?

  Hello Helpdesk-Kerry,

  Then, it should be accessible. Perhaps, try another computer if after restarting it does not open yet?

  Kind regards

• Legacy with defective power supply unit. Looking for replacement source

  RND4000 (ReadyNAS NV + v1 [v3]) group legacy with a power failure. Looking for replacement source. Not after replacement free of charge since it is obviously out of warranty and end of product life. However, it is a little expensive Kit to replace. If I did, I would still want to use it as a backup of synchronization for the new.

  I was unable to find any power supply corresponding by the name given to the unit (ST-220FUB-05F), all the results of my research resulted in a power different with smilar looks and namesake. Main differences are slight changes in the output rails, different output connectors. Also include a fan that mine didn't, perhaps a clue to the failure there.

  I was shocked to find that he was / is none replaceable fuse in the power supply and if there was a gauge commonent that he was unable to do the job because a cracket big mosfet to clean his radiator, think that's what it is, hard to see in here. Unable to find a replacement, I'll have to try to replace the component that is visibly damaged. Not easy because it's crowded in there and may fail because there are perhaps other failing components that didn't explode or evacuate. I really need ot get this unit backup and running.

  Help, please. Consider the purchase of an equivalent of second hand RND4000 for parts. See you soon.

  Hello EkDor,

  This replacement of power supply was free until supplies last and I heard they already ran out of it.

• On a NI USB 4432 device, any C++ APIs, interface with C++ application module.

  1.C ++ API - can I interface with the NI USB 4432 through a C/C++ application, she api C/C++ or dll.
  Need to get the entry/signals of the module in a C/C++ application.
  2. compatibility - information of the BONE, is the product drivers Windows XPE (XP Embedded) compatible?
  3. any link/site for documentation full on the module

  You must use the NI-DAQmx driver

  http://www.NI.com/dataacquisition/nidaqmx.htm

• Interfacing with several unknown USB devices; all producing NMEA strings

  Hi all

  Question about the peripheral USB interface and their associated drivers.

  I have the obligation to build an application that interacts with the USB devices that produce NMEA strings. I have the library to parse NMEA strings, but I fight with interfacing with several unknown USB devices. When deploying applications, I know not all possible USB devices to use.

  Is it possible to produce one driver who will accept any USB device strings?

  Or, more likely, is there a way to get the LV to recognize a connected USB device and automatically find / install the driver like windows does and is it possible to do in a deployed application?

  I had a trawl of the forums, but I've not found anything that specific.

  Thanks, I really appreciate the help.

  About the VI "set up the serial port", my problem is that the choice of COM port is in a separate menu (not directly related to the VI) and it allows all possible COM ports to be selected. That can be addressed.

  I am not expecting an all-in-one solution but asked the question in case it was possible.

  What I realized, is that for my specific condition to read strings from a USB device. It is likely to be sent over a serial connection. LV can handle this well and easily assuming the device has the installed driver / settings are available.

  LV (and indeed any other program) will not work without a device driver / settings. In this case, parameters set must be found (error) / a USB RAW driver would need to be developed. Devices requirng a RAW USB driver would need a serious review to continue due to the time and effort required. All this effort is work inherited from the AIDS to navigation

  I appreciate any help and I think I got the answer I was looking for! Thank you very much

• LabVIEW interface with micro contoller

  I'm new to labview. I need to know if the DAQ card is necessary to interface with micro controller? If no need then one can you explain how inter face microcontroller 89c 51 with Labview... If necessary, explain how interface?

  JEAN ASOKAN

  
  

• A module C - DAQ exists which will interface with standard RV - C?

  Module C - DAQ exists that if interface with standard RV - C (vehicles recreational CAN)? RV - C seems to be a variant of J1939 according to Wikipedia.

  I would use 9861 OR or NI 9862. I'm new on CAN protocol and evaluate some assistance.

  I've never used RV - can, but according to Wikipedia, the rate is 250Kbaud, so you'll want high speed CAN peripheral, 9862, you can set baud rate on init of the material.  After installing XNet and cDAQ software, you have a max bus monitor and several examples in the example Finder to read and write raw images.  After that, you'll want to read on the standard to understand how to format and analyze the data.

  Also if you have any questions, you can post on the Sub-forum Auto , they can probably answer more specific questions.