Internal error of screw, PDM file storage

Similar Questions

• repair error 2503 PDM file to recover data

  Hello

  I met a system failure, while writing data to a file of PDM and subsequently can no longer access the PDM data and get "2503" code say error this file is not in line with the style of PDM file format.

  I read the forums and have seen some solutions and has tried to fix the file using other vi but the closest, I had a partial recovery with the majority of deleted data. My file must have four sets of data, tests are the first 3 and the 4th is the important data, recovery seems to delete the data in the last section, which is the important thing and the file is greatly reduced. I did this on a copy of the file so still have the original.

  Delete the index file doesn't help at all.

  I tried to copy and opening of another place that does not work.

  I opened in a file Analyzer that provides a load of code in the hexagonal section, I don't understand, but the last entry made at a reasonable time for the data collected and useful stamp.

  The data are relatively simple, different channels of the same format of an acquisition of measurement data.

  It seems that the data is always there that the file is of a reasonable size for the expected data, but I don't know how to fix and read the data, its really important to access the data, can anyone help?

  the files are attached

  Thank you

  -camm-

  There are 17 segments in the file. #1 à #15 segment are all about 'Thermocouple, Thermocouple #1, Thermocouple #2' groups and channels in them. the 16 segment #, #17 talk about "Thermocouple #3" and channels in it that you are not really worried. These 2 segments stored only metadata about them. If everything went right, it should be a #18 segment that needs to store the raw data on it for «Thermocouple #3» channels And this segment should begin at offset 0xCA000. But there is no such segment. The data offset 0xCA000 is not follow the format of the PDM. Analysis all data after 0xCA000, it is not even a piece of bytes corresponding to the format of the header of PDM. All data after 0xCA000 looks like spilled invalid souvenirs in the file when the system crashed. And it decreases the size of the watched file "reasonable."

  The conclusion is that the raw data for "Thermocouple #3" had not been recorded in the file.

• End of the file has detected the error for more than one column of a PDM file playback

  Hello fans of LabVIEW,.

  I write the data in several columns of a PDM file. After that, I would like to read the data in each column to treat it.

  writing data works without any problem, if I get a PDM file with say 4 columns of data. When I try to read these columns now, LabVIEW always gives me error 4 "end of file" for all but a PDM read functions. Regardless of the number of columns I've read or how big they are, its still the same. LabVIEW reads a column and gives the error for all other tdms read functions.

  Does anyone has an idea how to solve this problem?

  A picture of my VI and the error is attached.

  Pls find attached extract

  

• Files not open Adobe reader (PDF) with the error "internal error...". »

  I have a desktop running windows 7 (64-bit) and adobe programs work very well in Administrator account until I added another user.  After you have added the user account standard adobe (reader, Flash Player) programs work fine on the standard account and not on the administrator account. It doesn't matter if I'm trying to use through a browser or not.

  I tried to fix the reader through Control Panel and reinstall without change.

  whenever I try to open a pdf file or access a web page with flash player content I get a
  error message "internal error."

  Original title: adobe "internal error."

  I tried the suggested methods and system restore did nothing to help me.  When I open a new adobe for the administrator account programs worked well.  I don't have to changing the profile settings immediately.

  Then by chance, I tried to access My Documents folder via the file of users instead of the desktop icon (I have had no problem with) and received the message that I don't have permission to access this file and I didn't have the right to change the security settings.  I checked the property settings and he showed that no user had possession, so I was able to change the property on my administrator account. Still not sure how this happened, oh well.

  That fixed my problem with adobe, and all works well. Now, I can remove the second administrator account.

  Thank you for your help.

• I just bought, installed and registered 6 Lightroom. When I try to launch the product I get a message that says "an internal error has occurred" - could not create the required file: admin/Users / / Library/Application Support/Adobe/Lightroom/filter

  I just bought, installed and registered 6 Lightroom. When I try to launch the product I get a message that says "an internal error has occurred" - could not create the required file: admin/Users / / Library/Application Support/Adobe/Lightroom/Filter Presets. Any ideas on how I can fix this?

  Hi Anthony,.

  You must go to the location: admin/Users / / Library/Application Support/Adobe/Lightroom

  Hold down the CTRL key and click on Lightroom, click on read the information and click the permissions tab.

  Provide the permissions to read and write to your identifier and then close.

  Then reopen Lightroom. You should be able to open Lightroom.

  Please let us know if it helps.

  Kind regards

  Tanuj

• You use Mac OSX 10.7.5, when you try to open a PDF file, I get a message "an internal error has occurred." I uninstalled and reinstalled both Adobe 10 and 11. Anyone know of the problem and the solution?

  You use Mac OSX 10.7.5, when you try to open a PDF file, I get a message "an internal error has occurred." I uninstalled and reinstalled both Adobe 10 and 11. Anyone know of the problem and the solution?

  Hi Charles,

  
  

  It is specific to a particular file or all the files that you are trying to open, gives you the error.

  How you open the same file using Preview on Mac.

  
  

  Thank you

  Vikrantt Singh
  

• Validate the recovery area / files results in RMAN-00600: internal error

  Dear members,
  
  I did experience (specifically RMAN) with Oracle 11.1.0.7 on instance AWS (amazon delegating thingy).
  

  SQL> select * from v$version;
  
  Oracle Database 11g Enterprise Edition Release 11.1.0.7.0 - Production
  PL/SQL Release 11.1.0.7.0 - Production
  CORE    11.1.0.7.0      Production
  TNS for Linux: Version 11.1.0.7.0 - Production
  NLSRTL Version 11.1.0.7.0 - Production

  Database instance works fine, so far.
  However when I try to VALIDATE the recovery or file BOX, she translates RMAN-0600 as follows...

  RMAN> validate recovery area;
  
  Starting validate at 15-JUN-12
  using channel ORA_DISK_1
  RMAN-00571: ===========================================================
  RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
  RMAN-00571: ===========================================================
  RMAN-03002: failure of validate command at 06/15/2012 19:00:33
  RMAN-00600: internal error, arguments [8708] [] [] [] []

  Any help is greatly appreciated.
  Sincerely,
  Jennifer B.
  
  PS:
  All others to VALIDATE the options work great.
  One runs in such situation? I searched for his MOS, Google and this forum but nothing helped :-(

  Hello;

  I'm pretty sure it's a bug.

  It is an Oracle noted that while not an exact match is very, very close.

  VALIDATE ARCHIVELOG ALL fails with RMAN-00600 [8708] [974813.1 ID]

  Best regards

  mseberg

• CS6 tormented by internal error occurred on saving a file

  CS6 (win 7) I am tormented by CS6 failing to save a file with the message of dialogue that an internal error has occurred and no idea how to diagnose or repair.

  It is is simple file containing 20 symbols one to a page. Sometimes restart reopening and the backup will work, sometimes rename and relocationg file will work, sometimes it isn't.

  The inability of the program to save your work is a bug of the gravity and the higher priority.

  I solved this problem by renaming both files to: C:\Documents and Settings\your.name\Application CS6\English:

  CS6 Panel Prefs.xml Fireworks

  CS6 Preferences.txt Fireworks

  Their evolution:

  CS6 Panel PrefsOLD.xml Fireworks

  CS6 PreferencesOLD.txt Fireworks

  After you rename these files, Fireworks works normally again.

  I am running Windows XP Professional, if the path may be slightly different if you are on a different version of Windows, but files should be nearly the same way.

  I hope this helps!

• Internal error in safari on download (navigation finder via safari)

  Hello

  I have a problem with Safari. Whenever I try to send, or upload a file, or just browse the finder (see imageView imageView imagehttps://www.google.co.uk/url?sa=i & rct = j & q = & esrc = s & source = image & cd = & cad = AJLN uact = 8 & ved = 0ahUKEwiD-JO9taPOAhVrI8AKHZgMCkUQjBwIBA & url=http%3A%2F%2Fcdn.osxdaily.com %2Fwp-content%2Fuploads%2F2014%2F12%2FSHRINK-SAVE-DIALOG-WINDOW-OS-X.jpg & bvm = bv. 128617741 d.ZGg & lb/po2 = AFQjCNE-8daDlrJRNqFPh3oWGIrw26bWaw & 1470250870765789 = ust) I get an internal error like this :

  

  Details of the accident report are:

  http://pastebin.com/Q8gH5LQp

  Any help would be appreciated. Thanks in advance.

  Moreover, the accident report is when I tried to use Google Chrome, and the screenshot in the thread above was when I was with Safari.

• 500 internal Error Privoxy keeps occurring when I load the page.

  I get an internal error 500 of Privoxy when I open http://www.thoroughbredgt.com/

  Error reads: Privoxy has encountered an error while processing your request:

  Unable to load template file without Server-data or one of its components included.

  Please contact your administrator for the proxy.

  If you are the administrator of the proxy, please put the files required in the (confdir) / templates directory. The location of the directory (confdir) is specified in the main Privoxy configuration file. (It is usually the installation of Privoxy directory).

  I can't understand how to solve the problem. Any help?

  I have not had any problems.
  Try this link; http://www.thoroughbredgt.com/

  It could be that there is something to block this site, like a firewall.
  Contact your provider and ask questions. Try the link on another
  computer, or another browser.

• "27049 internal error" when you use recovery with Equium A60-692 utility

  TOSHIBA SATELLITE A60 - 692

  I'm trying to fix a friends laptop. The laptop computer wouldnâ? t start, would go to the blue screen just before the came WinXP loading screen then will re-start. I used a USB 2.5 HDD enclosure "to copy important files on my laptop and then formatted the drive of my laptop. I put the HARD drive in the Toshiba and have used the CD of restoration via an advanced option. on exactly 9mins 50sec time on the recovery process, an error message appears (27049 internal error). After that, it goes to a screen of style BACK with a little more information. Essentially by specifying that the error is "cannot read FILE_BITMAP MFT entry.

  I cleaned the CD
  I swapped the CD drive with my laptop
  Quick formatting it formatted, it is full
  Used the basic option where it does itself and it ERRORS with - not enough space on the partition - there is no partition! or if there's empty sound

  What can I do?

  Hello

  I think that the HARD drive is broken, because if you receive an error message with words like "MFT" (meaning MasterFileTable) then you can expect that the HDD has serious problems.
  OK, easy to talk to it s fast without knowing the machine and so on, but I know a similar error and I can give you the advice to probe hard disk errors.
  You can do this with the help of the "ultimate boot cd" which is a very interesting tool when you need information about your computer or you want to just check if everything works well.
  Here´s the link to the downloadable CD image that should be on a CD:

  http://www.ultimatebootcd.com/

  Hope you can solve this problem...

  Welcome them

• An internal error occurred during the processing of this Mathscript

  I tried to run a ".m" file it starts with a number of % "commented" statements to help the program implemented. "  I get this error as above as "internal error in row 0, then the error message. Please notify it is a problem using % or else where in the program?

  Chuck

  Hello Chuck,

  This error indicates there is something in your script that LabVIEW MathScript did not understand.  As such, it depends on the script that you typed.  Is it possible to attach your script?  If this isn't the case, you can try a binary search with your script.  Remove half of your script.  If the problem persists, the culprit is in the half top.  Remove half of the upper part of the half and reaffirm.  If this isn't the case, it is at the bottom half.  Add in half of the text you removed and try again.  After you have identified where the problem occurs, you can try to simply the script by removing other lines that are not necessary to run the problem line.  If then you can put what you have, I can investigate on what is wrong.

  It is possible that comes to mind if you perform a replacement of indexation of the following form:
  [(m, n) vs s] =
  In other words, one of the values of multiple return putting inside another matrix.  A solution for this is to do the following:
  [s] = so.
  vs (m, n) = a;

  Grant M.
  Staff software engineer | LabVIEW Math & Signal Processing | National Instruments

• PDM file with automatic backup on corrupts the data.

  When I test data stream into a file to PDM using AutoSave = true, data is corrupted in the 'package' #3 and beyond.

  I write matched double/DateTime data to a TDMS file configured as TdmsWaveformLayout.PairedTimeAndSampleChannels.

  When I try to read the PDM file, for example using the sample application to drive, I get all sorts of errors. Notably, the number of timestamps is not equal the number of samples (values y). More data is corrupted. In other words, the timestamps are invalid and the sample data is essentially random.

  This happens every time I write the third package/lot and beyond. If I write a single sample, followed by another single sample, the third will be corrupted. If I write 1 kilosample, followed by 1 kilosample, sample no. # 2001 will be corrupted.

  I guess that something is very wrong in the automatic backup routine, as data are always written correctly when I explicitly save the PDM file.

  It's using MS 8.9.0.246 in Visual Studio 2008 SP1 using .NET framework 3.5 SP1 on Windows 7.

  The TDMS file is created in the following way. Note that AutoSave is set to false to avoid the bug.

  TdmsFile f = new TdmsFile (tdmsFilename, new TdmsFileOptions (TdmsFileFormat.Version20, TdmsFileAccess.ReadWrite, true, TdmsByteOrder.Native));
  
  f.AutoSave = false; Must not be set to = TRUE because of a bug in Measurement Studio!
  TdmsChannelGroupCollection channelGroups = f.GetChannelGroups ();
  
  ChannelGroup TdmsChannelGroup = new TdmsChannelGroup (...) Unique ID...) ;
  
  channelGroups.Add (channelGroup);
  f.Save (); Needed when AutoRecovery is set to false.
  TdmsChannelCollection tdmsChannels = channelGroup.GetChannels ();
  
  foreach (IDicomInstance instance in series. Instances)
  
  {
  
  	tdmsChannels.Add (new TdmsChannel (string. Format ("{0} (time) ', for example.") Signal.Name), TdmsDataType.DateTime));
  
  	tdmsChannels.Add (new TdmsChannel (string. Format ("{0}", for example.) Signal.Name), TdmsDataType.Double));
  
  }
  
  channelGroup.WaveformLayout = TdmsWaveformLayout.PairedTimeAndSampleChannels;
  

  Every 10 ms, a double array [100] happens (with information in a DateTime table clock [100]). The data is stored in the file TDMS in a simple way:

  AnalogWaveform wf = AnalogWaveform. FromArray1D (sample. Data.Samples);
  
  WF. Timing = WaveformTiming.CreateWithIrregularInterval (sample. Data.Timing);
  
  WF. ChannelName = sample. Source.Name;
  
  WF. UnitDescription = sample. Source.UnitOfMeasurement;
  
  ChannelGroup = _tdmsFile.GetChannelGroup (... TdmsChannelGroup Unique ID...) ;
  
  TdmsChannel channel = channelGroup.GetChannel (... channel... name);
  
  channelGroup.AppendAnalogWaveform(channel, wf);
  
  channelGroup.Parent.Save ();  Needed when AutoRecovery is set to false.
  
  

  This is what the TDMS file looks like in the sample player application:

  

  For those who can run in it before we are able to get a fix on, a viable solution is to turn off auto-save and save the TDMS file any time a change to the file is made manually, such as after adding channels or groups, or write data.  This will not negatively affect performance, because that's exactly what the property of automatic backup.

  It should also be noted that this problem arises when you use the layout of the TdmsWaveformLayout.PairedTimeAndSampleChannels waveform.

  I'll post back later when we have a fix for this problem.

  Sorry for the inconvenience that this may cause,

  NickB

  National Instruments

• allow to create or write a PDM file with labview 2014

  Hello

  I need help. I'm new with LabView. I tried to create a PDM file, but it does not work. My code in the link below is really simple, but I don't know what the problem is. My code doesn't throw any errors so I don't know what to look for in the internet. Once my code is excuting, no file is created. I use LabView 2014 and my laptoop has windows 7 on it.  My question is, in all I need to do whenever I create a new VI of specific configurations that will be play/create/write a .tdms so that my code may work correctly because the writing in a .txt file works perfectly.

  Thank you and sorry for my English

  Hi bmtanguay,

  you want to run your VI on your cRIO9074?

  Where do you think your cRIO creates this file? A cRIO is a clean computer - and it has its own 'hard drive '. This is where your file is created: C partion on your cRIO!

  You cannot create a file on your Windows pc from a VI running on your cRIO!

• Cannot open the PDM file with excel 2016

  Hey guys,.

  I have Office 2016, LV 2015 and (I checked my "TDM Excel Add-in" file) the Excel Add-in 2015 of CT.

  I have attached a picture of what I get when I try to open the PDM file with excel.

  So, I found something strange. I checked active supplements under the excel options and the TDM Excel Add-in is listed as inactive (and is called a COM-add-in). I tried to activate it, by checking the box (see the second picture), but that does not change. Interesting is the last line of my second attached photo:

  Translated it means: ' loading behavior: a runtime error occurred when trying to load this Add-In.

  I have 10-64 bit operating system like windows.

  Someone at - it a solution?

  Kind regards

  Slev1n