Internet access on the same network

Similar Questions

• After that Windows 7 conclusion "No Internet access" in the wireless network?

  I have a USB wireless network card installed in my office. All judging by the "connected network" showed, that he manages to connect to my wireless router, with I can't visit all websites due to "free Internet access". Only if I move my router where (almost) no wall blocking the path between my office and the router, will be solved the problem.

  There is no problems surfing the Internet using my laptop (Windows XP) and the iPad, which also connect to the router.

  I don't know what "No Internet access" while "Connected network" appears. To understand this, perhaps I should know what Windows 7 draws the conclusion "No Internet access" to the wireless network.

  Thank you, everyone. I managed to figure out the problem last night. With this document that I found by Googling, http://www.usb.org/developers/whitepapers/327216.pdf, I tried to disconnect my DVD ROM USB plugged next to my wireless network card and found that this really WORKED, although the DVD ROM is USB 2.0 instead of 3.0.

  In addition, as Shawn "Cmdr" Keene [MVP] said, I really need to I ignore the message "connected network". I ran the Ipconfig/all command frequently and found that sometimes the IP address of my wireless network card was no longer * 192.168.0 and the gateway, and the IP addresses of the DNS servers are null, even if the message "Connected network" remained all the time.

  Hope this helps others who also have this problem, even though my English is not very good. : )

• Termination of the client PIX VPN and Internet access from the same interface

  Hello

  VPN remote users connect to PIX (7.2) outside interface, but need to have these clients to access the Internet through the PIX outside interface as well. Need this because PIX IPs is registered and allowed access to some electronic libraries. One way would be to set up a proxy within the network and vpn users have access to the Internet through the proxy, but can it be done without proxy?

  Yes, public internet on a stick

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00805734ae.shtml

• Best way to extend the network of Apple using Cat5 and wireless, but with access to the same network

  Appreciate any help here.

  I need to extend my network coverage for the part out of my house where the current signal does not cover.

  I have a Time capsule in the office connected to my Modem and then created a wireless (XXXX) network that connects to the extreme in my front room... .well when I'm in my room before the signal does not increase when I go near the extreme... and maybe it's that I'm still picking up XXX to my Time Capsule wireless network.

  I'm just a Cat5 cable around the House and I was wondering if I can connect the TC to the extreme via CAT5 and therefore the extreme would be able to stream my network wireless XXXX?

  If I then want to connect to another airport (explicit / extreme or even TC) in the part of my house which currently gets no signal... then do cela via Cat5 to the EXTREME at the 3rd device... or must it come directly from the TC?   (and again... the 3rd device will also be able to broadcast the network XXXX?

  Ideally, I want the network to be possible STB and flavours around the House, and I think that the connections between Ethernet devices would accomplish that... but I also need the i-devices, streaming boxes etc. around my house to then access the XXXX wifi network I have printers, VPN, etc all together towards the top on.

  Oh... and 1 other point, I have a cisco 8port 10/100POE switch managed... which I would also like to include in the network to connect to the servers and devices IP etc... is - it possible... and that has to be directly connected to the time Capsule and could I still use it to take place between the TC and the 3rd Apple Airport device... as above?

  Hope that makes sense... but please let me know if you need more details.

  I'm just a Cat5 cable around the House and I was wondering if I can connect the TC to the extreme via CAT5

  Yes. Hate to be picky here, but I hope you'll use CAT5, CAT5e cabling being quite a bit obsolete.

  wireless network and if so the extreme would be able to stream my XXXX?

  Yes

  If I then want to connect to another airport (explicit / extreme or even TC) in the part of my house which gets currently no signal... then do cela via Cat5 to the EXTREME at the 3rd device

  Yes, but it would be preferable to cables to connect the 3rd to the main TC, if that's an option.

  or does have to come directly from the TC?

  No, but it would be better if she could, if this is an option.

  and once again... the 3rd device will also be able to broadcast the network XXXX?

  Yes

  and I think that the connections between Ethernet devices would achieve this

  That is right. Ethernet is always the best choice in terms of performance.

  but I also need the i-devices, streaming boxes etc. around my house to then access the XXXX same wifi network I printer, VPN, etc all together towards the top on.

  That should work well.  However, you may not aware that most of the PC and iOS devices not 'automatically' between different wireless access points as they move from one place to the other.  For example, you have your iPhone near the time Capsule, so he'll be looking for a strong signal from the time Capsule. If you move the close AirPort Extreme iPhone or any other device 3rd... the iPhone usually will stay connected to wireless Time Capsule... even if a stronger signal may be available in another wireless access point. Nature of the beast with IOS devices.

  Thus, with most of the PC and iOS devices, you will have to get used to temporarily turn off the WiFi on the iOS device when you move from one place to the other, then re - turn on WiFi once the device is close to the other wireless access point. The iOS device then generally will pick up the strongest signal from the nearest access point.

  Portable Mac computers will generally do a good job of automatically 'switching' to pick up the best signal of different access points in you walking the laptop around the House.

  I have a cisco 8port 10/100POE switch managed... which I would also like to include in the network to connect to the servers and devices IP etc... It is possible.

  Yes, but the Time Capsule and AirPort Extreme Gigabit Ethernet ports or 10/100/1000, then the switch is going to limit the maximum speed on the network at 100 Mbps when the devices are capable of much higher speed.  If you plan to invest in the installation of Ethernet wiring around the House, then you also want to invent a new Gigatibit Ethernet 10/100/1000 switch, because it will allow up to 10 times faster compared to a 10/100 switch network connections.

  can do this via Cat5 to the EXTREME at the 3rd device... or need to come directly from the TC?

  Yes, but it would be best to connect the switch to the time Capsule if it is an option.

  and could I still use it to take place between the TC and the 3rd Apple Airport device... as above?

  Yes

• Connected to wifi but not internet access and the unidentified network

  I can't connect to internet, I need quick help.

  Hello

  This screen that you took the photo, there should be a small link somewhere that says "view log" you can copy the text of the log file and send it to me?

  In this photo, however, the only thing I see is Homegroup questions, which are not generally associated with internet connectivity... but who knows?

  You can try to manually start the Homegroup provider service. To do this, go to the search box of the start menu and type services.msc and press ENTER. Find the services marked "Homegroup Provider Service" and "Listener Homegroup" Double click on each one and set to automatic startup type. Restart your computer. Let me know how it goes.

  One more thing to try is to clear your cache of DNS resolution. At the beginning of the search box go menu, type cmd and press to enter. Type ipconfig/flushdns press on enter, and then restart your computer.

  I hope this helps!

  Mithrandir

• CANNOT ACCESS VISTA BY XP AND CANNOT ACCESS XP SINCE VISTA WITHIN THE SAME NETWORK MACHINE

  I'm using vista Business. while I try to view other machines with the same working group in the same network... My machine only manifests itself in the network... No, other machines are available... and will have remote desktop also does not work if I have an address user name and password and IP address of the remote computer running xp...  Help me.

  Hi NIRAJ KARKI,.

  You can't use Remote Desktop connection to connect to remote computers running Windows XP.

  This package contains the Link Layer Topology Discovery () LLTD Responder. The network map on a computer running Windows Vista presents a graphical view of the computers and devices on your network and how they are connected using the LLTD protocol. The LLTD Responder must be installed on a computer that is running Windows XP before it can be detected and appear on the network map. After you install this item, you may have to restart your computer.

  I suggest to install Layer Topology Discovery LLTD Responder (KB922120) (Link) and check if the problem is resolved.

  Link Layer Topology Discovery (LLTD) responder (KB922120)
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=4F01A31D-EE46-481e-BA11-37F485FA34EA&displaylang=en

  You can check the link below.

  Setting up a network home
  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-home-network

  Please post back and let us know if it helped to solve your problem.

  Kind regards
  KarthiK TP

• The Switch configuration and Wi - fi router in the same network

  Hi team,

  I have here is the configuration currently as below in the image. To describe the same internet cable is connected to a Cisco switch, which is connected to the PC in LAN (wired). A switch output is connected to the entrance of the wireless router Netgear Nighthawk AC 1900 Smart model of WiFi router # R6900. Wireless devices (laptop) are connected by the router.

  Each device has internet access. However, I am unable to run software LAN or unable to share any file of devices connected to the switch to the connected wireless devices. I can't ping any device the device wireless wired.

  Can anyone suggest what are the settings that I should do or what are the steps I should follow that will make wireless and wired devices in the same network.

  PS Plus early I tried the internet connection to the wireless router and then out of the router to pass, which has solved this problem. But slowing down my internet speed in wired devices. So, is it possible to have all devices in the network even with the current configuration?

  

  Thanks in advance.

  Best,

  Hardik

  I made wi - fi router reset hardware and configured in Access Point mode, that solved my problem.

• BEFSR81 with WRT54GS to the same network?

  I currently have a LinkSys BEFSR81 connected to a cable modem that I need at least 6 ports wired to my home network.  I also have a WRT54GS which is currently unused, but I want to add to the network so I can have both wireless connectivity.

  Assuming that it is possible, what is the best way to combine the two units in the same network?  The simply connectable WRT54GS downstream of the BEFSR81 via one of the ports open?  I guess I'll have to change the IP address of the wireless device for individually accessible for configuration, check status, etc.  All the other things I have to do?

  Please notify / thank you!

  I found the solution in a previous post, sort of.  Here's what worked for me:

  (1) connect direct PC to WRT54GS

  (2) turn off DHCP and change the WRT54GS IP to 192.168.1.2 (192.168.1.1 for the 'master' BEFSR81 vs).

  (3) save changes

  4) activate wireless, configure security, get access, etc. on the WRT54GS code

  (5) save changes

  (6) re - connect the PC to the original port BEFSR81

  (7) connect the ethernet on BEFSR81 port to a port ethernet on the WRT54GS (NOT the Internet port)

  (8) to enter the code in the WiFi device and make the connection...

• problem with Internet connection sharing, error: connection ad - hoc has "no internet access" on the cell phone of the customer

  Original title: problem with Internet connection sharing

  my laptop running on Windows Vista Home Premium SP2 (this one has access to the internet by using the dial-up modem and will to act as a sharer of internet connection or as a host) and the client computer runs on Windows 7 Starter

  in a first step, I try internet connection sharing, I've set up an ad hoc network and I just changed my setting modem dial-up on the sharing tab, of course what I change, it of 'Allow an other network users to connect through this computer internet connection' and choose the on Home Networking connection wireless network connection , then my mobile client to connect to a special that I created and portable client connected to the internet via ICS
  then the problem came when I restart my laptop. When I tried to use ICS once again, my customer laptop really takes a long time to connect, he continues saying 'identification' side host and client. and after that "identify" is complete, it says ad - hoc connection, I create has "no network".
  so, I'm a person answer in this forum
  ' Obtain an IP address automatically is the wrong setting on the Ethernet connection. "  To return to the sharing tab and unshare the wireless connection.  Close all windows network, and then open them and re - share the wireless connection.  Who must configure IPv4 for the Ethernet connection properties for:

  IP address: 192.168.0.1
  Subnet mask: 255.255.255.0
  Default gateway: no
  "DNS server: none.

  I put this on my laptop of the host, and and I put the IP address on my laptop customer in 192.168.0.2 with the same default gateway as my portable computer host IP

  and made some progress in this case, when I try to connect host and the client is no longer to 'identify' phase, immediately connected laptop both but my mobile client can not connect to the internet and displays "No Internet access" on the ad hoc network, I have create

  I tried a lot of things but always completed my mobile client can not connect to the internet and displays the message "no Internet access.

  What makes me confuse is first, I try to share the internet connection everything works like a charm, I set up an ad hoc network, and then change the setting on my modem dial-up so he can share the internet connection, and voila, computer laptop client connected to the internet. I change even not all IP settings

  But why after I restart my PC, this problem comes...

  someone knows how to help me with this problem?

  Hey, Mimbs,

  You can try the similar thread to the next with a possible solution:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/no-Internet-access-in-the-client-machine-when/77312e09-4385-41FA-A420-0c42be58e4e3

  Also for reference:

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

• Connect 2 routers on the same network? !!

  Hello

  I can't get this to work...

  I have a modem connected to the ground floor for internet cable.

  I needed an extra blanket so I bought a linksys wrt120n to put on the floor.

  It is connected directly to the modem downstairs via ethernet.

  However I can't get them on the same network (or my clients at least)

  I gave the same SSID and tried various things, but when it is connected to the linksys, sometimes I don't see the pc down and sometimes I can't! ???

  Please, can someone give clear and easy to follow steps on how to get everything on the same network?

  Thank you...

  Here's how to connect several routers in your network. You need a LAN - LAN configuration so check all the computers together. If you use Internet-LAN, the network from the router won't be available outside of the unit.

• I have windows server 2008 R2 and windows 7 32 bit on the same network. But I couldn't see the server on the network.

  I have a windows server 2008 r2 server and windows 7 32 bit on the same network.

  I couldn't see the server on the network and

  also I could not access the workstation to the server.

  not more than one device must perform NAT

  Hi Bruce,.

  Given that you are working on Windows server 2008 R2, please post your question here:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Client remote access VPN gets connected without access to the local network

  : Saved

  :

  ASA 1.0000 Version 2

  !

  hostname COL-ASA-01

  domain dr.test.net

  turn on i/RAo1iZPOnp/BK7 encrypted password

  i/RAo1iZPOnp/BK7 encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP 172.32.0.11 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 192.9.200.126 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  nameif failover

  security-level 0

  192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

  !

  interface Management0/0

  nameif management

  security-level 0

  192.168.2.11 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain dr.test.net

  network of the RAVPN object

  192.168.0.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.200.0_24 object

  192.168.200.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.9.200.0_24 object

  192.9.200.0 subnet 255.255.255.0

  the inside_network object-group network

  object-network 192.9.200.0 255.255.255.0

  external network object-group

  host of the object-Network 172.32.0.25

  Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

  access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

  access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

  access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

  192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

  pager lines 24

  management of MTU 1500

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) source Dynamics one interface

  NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

  Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.9.200.0 255.255.255.0 inside

  Telnet timeout 30

  SSH 0.0.0.0 0.0.0.0 management

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 66.35.45.128 255.255.255.192 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 30

  SSH version 2

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal RAVPN group policy

  RAVPN group policy attributes

  value of server WINS 192.9.200.164

  value of 66.35.46.84 DNS server 66.35.47.12

  VPN-filter value test123

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value test123

  Dr.kligerweiss.NET value by default-field

  username test encrypted password xxxxxxx

  username admin password encrypted aaaaaaaaaaaa privilege 15

  vpntest Delahaye of encrypted password username

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  Group Policy - by default-RAVPN

  IPSec-attributes tunnel-group RAVPN

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory 2

  Subscribe to alert-group configuration periodic monthly 2

  daily periodic subscribe to alert-group telemetry

  aes encryption password

  Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

  : end

  COL-ASA-01 #.

  Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

  Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

  25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

  29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

  38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

  56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

  69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

  98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

  99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

  108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

  115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

  116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

  COL-ASA-01 #.

  Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

  And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

  Hello

  The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

  You can try the following changes

  attributes global-tunnel-group RAVPN

  No address RAVPN pool

  no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

  local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

  In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

  the object of the LAN network

  192.168.200.0 subnet 255.255.255.0

  network of the VPN-POOL object

  192.168.201.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

  NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

  You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

  No source (indoor, outdoor) nat Dynamics one interface

  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

  Hope this helps

  Let me know if it works for you

  -Jouni

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• can I configure an IPv4 address and IPV6 on the same NETWORK card

  I test double stack IPv4 and IPv6 on a firewall.  Can I configure IPv4 and IPv6 addresses on the same NETWORK card using a laptop installed with Windows 7, in order to test the firewall for both IPv4 and IPv6 protocols access? And if so, how to configure the NETWORK card?

  Thank you

  Jack P.

  See what...

  http://Windows.Microsoft.com/en-us/Windows7/change-TCP-IP-settings

• Acrobat DC - set the speed of internet connection to the local network

  Hello

  Is it possible to adjust the speed of Internet connection to the local network (in Edit > Preferences > Internet > Internet Options) using the DC Acrobat Customization Wizard?

  Thank you!

  Samir Rossi

  Use the Adobe Customization Wizard Registry Panel and this entry:

  [HKEY_CURRENT_USER\Software\Adobe\Adobe Acrobat\11.0\AVGeneral]

  "iConnectionSpeed" = dword:00989680