Similar Questions

• DMVPN Tunnel and EIGRP routing problem

  I have redundant paths to a remote 2811 router on my network of sites.  The first links is a T1 frame relay connection that has been in place for years, and the new link is on a 54 Mbps fixed wireless that was recently created.

  I'm under EIGRP to my process of routing protocol 100 for the two links.

  I installed a DMVPN Tunnel between the remote 2811 and no. 2851 router on my host site.  The tunnel interface shows to the top and to the top of both sides and I can ping the IP remote tunnel of my networks side host.

  However my eigrp routes are not spread over this new tunnel link and if I run a command show ip eigrp neighbor on each router I show only the neighbor for the frame relay link and not the new wireless link.

  What I'm missing here?

  A tunnel0 to see the shows the following:

  Tunnel0 is up, line protocol is up
  Material is Tunnel
  The Internet address is 10.x.x.x/24
  MTU 1514 bytes, BW 54000 Kbps, DLY 10000 usec,
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  KeepAlive not set
  Tunnel source (FastEthernet0/1), destination 172.x.x.x 10.x.x.x
  Tunnel/GRE/IP transport protocol
  Key 0x186A0, sequencing of the people with reduced mobility
  Disabled packages parity check
  TTL 255 tunnel
  Quick tunneling enabled
  Tunnel of transmission bandwidth 8000 (Kbps)
  Tunnel to receive 8000 (Kbps) bandwidth
  Tunnel of protection through IPSec (profile "CiscoCP_Profile1")
  Last entry of 00:00:01, exit ever, blocking of output never
  Final cleaning of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 947
  Strategy of queues: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bps, 0 packets/s
  5 minute output rate 0 bps, 0 packets/s
  packages of 880, 63000 bytes, 0 no buffer entry
  Received 0 broadcasts, 0 Runts, 0 Giants 0 shifters
  errors entry 0, 0 CRC, overgrown plot of 0, 0, 0 ignored, 0 abort
  output of 910 packages, 81315 bytes, 0 underruns
  0 output errors, 0 collisions, 0 resets interface
  unknown protocol 0 drops
  output buffer, the output buffers 0 permuted 0 failures

  Please go ahead and add a static route on the hub, so it goes through the wireless link and let me know if everything works correctly.

  Federico.

• How to recover or find the network key for a router wireless (Netgear)

  Network wireless adapter NIC Ethernet network device

  How to recover or find the network key for a router wireless (Netgear)

  Hi RaymondKramp,

  ·         What version of Windows is installed on your computer?

  If you have lost the key to network and not connected to the network, then you can reset the router to factory settings wireless.

  If you lost the key network and connected to the network, and then log on to the Web page of the router and get the key.

  For more assistance, you can contact Netgear Support:

  http://support.NETGEAR.com/app/home

  Hope this information helps.

• How can I find out the password for my router, I missed place

  I want to add another computer to use though, I can't find the password for my router.  Is it possible to find it on one of my other computers.

  Except if you have really tightened down on the security of your router, adding another computer should be a simple to plug it.  In any case, most routers can be reset by default (including the password) by pressing the button of reset for about 10 seconds.  As you do not have the brand or the model of router in your post, all I can recommend is for more specific information, you should go to your router manufacturer's website and download the manual for your make and model of router and follow the instructions.

  HTH,
  JW

• XP key wep changes for new router linksys after the connection. you need to reinstall the WEP every time you start from the top.

  XP key wep changes for new router linksys after the connection. you need to reinstall the WEP every time you start from the top.

  Hello

  Let us perform the steps below and check out them.

  a. click "Start," "Control Panel", then "Add or Remove Programs". In the box "Currently installed programs", find the name of your wireless router. Click on the name of the software, and then click 'remove '. Click 'Yes' when prompted to confirm.
  b. click "Start" then "run". Type "Services.msc" and click "OK". Select 'Wireless Zero Configuration'. Click on 'start '.
  c. click 'Action', 'properties '. In the drop-down menu "Startup Type", click on the arrow and select 'Automatic' to assign the commissioning of automatic Wireless Auto Configuration. Click on 'OK '.
  d. restart your computer.
  e. right click on "Wireless connections" icon Select "View available wireless connections." Click on "change the order of preferred networks. Select the name of your network, and then click "Properties". Erase the old key and enter a new. Click the checkbox next to "Automatically use that key." Click on 'OK '.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to install an extension for my router

  original title; HOW to SET UP NET GEAR for MY ROUTER to ALLOW MY EXTENSION greater DISTANCE for RECEPTION OF SIGNAL from main router

  I have a netgear router and I want to install an Extender (netgear), so I get enough power from further away in my house.  My main router doesn't have a button of annual work plans.

  Hello

  1. What is the model of the extender?

  Please see the link.

  http://www.NETGEAR.com/images/WN3000RP_DS_22Mar1118-17219.PDF

  I suggest also please contact Netgear support team for assistance.

  http://forum1.NETGEAR.com/

• under vista and it cannot open the Web 192.168.1.1 for linksys router

  I have a Linksys wrt54gl router wireless and I hard wire plugged into my computer so I connected to the internet broadband router. Connections to work because the flashing lights on the front of the router blink correctly.  So I open internet explore and type 192.168.1.1 in the hope that I get the page for the router setting, but instead, I get a message that explore cannot detect the Web site. Wrong address. I get a similar error with Firefox.  The computer was working fine connected directly to the internet bandwidth so sure the internet works. The IP address is set to automatic detection. Someone at - it ideas?

  Hello

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• NPS Windows Help for authentication of aaa for Cisco router - is it safe?

  I am very confused about how all this works and was hoping someone could help me.

  I followed a bunch of tutorials online for authentication RADIUS of installation on a Cisco router and he did to a NPS Windows Server. Now I can ssh into the router my AD account.

  Now that I got it to work, I go to the settings to make sure everything is secure.

  On my router, the config is pretty simple:

  aaa new-modelaaa group server radius WINDOWS_NPSserver-private 123.123.123.123 auth-port 1812 acct-port 1813 key mykeyaaa authentication login default local group WINDOWS_NPS
  
  ip domain-name MyDomcrypto key generate rsa
  
  (under vty and console)# login authentication default
  On the NPS Windows:
  I created a new RADIUS client for the router.
  Created a secret shared and specified Cisco as the name of the seller.
  Created a new strategy of network with my desired conditions.
  And now the frame of the configuration of the network policy that worries me:
  
  
  So initially I thought my AD credentials were being sent over the wire in plain text, but I did a capture and saw this:
  
  
  
  capture.jpg
  
          
      
  
  
  How is my password being encrypted and how strong is the encryption?
  
  Another thing is how can I configure aaa authentication with mschapv2? The documentation I saw for mschapv2 uses the "ppp authentication ms-chap-v2" command, but I'm not using ppp I'm using aaa with a radius server.
   
  			 
  Hello
  RADIUS encrypts the password, but sends the username in clear. GANYMEDE encrypts the user name and password.
  You can find the encryption used by RADIUS in the RFC scheme:
  https://Tools.ietf.org/html/rfc2865#page-27
  MS-Chap-V2 is used for the authentication of users such as the remote access and vpn, not management switch
  Thank you
  John
  		   

• wireless router not working do not: told by iYogi technical support for wireless router Netgear that my registry is corrupt

  My Netgear wireless router (model: N300 wireless (WNR2000v3) router wireless) has stopped working properly without Internet access for my laptop (there was a triangle 'yellow' small 'i' (exclamation point) on the Wi - Fi signal strength indicator in the lower right corner of my computer screen.).  I bought only the router ago 3 months 25/08/2012.  Netgear technical assistance is really "iYogi technical support.  After more than 3 hours, Abdullah, Tech support person had me change what I think are 'DNS' settings for the router, and it now the next day, Thursday, November 15, 2012, works very well, "so far".

  My question is this.  The "iYogi tech support" person said, after took my computer during the process of fixing my problem, I had 9% of my corrupt computer registry files and I need to have a computer system 'optimize' made, then I wouldn't have the same problem with the router, and other problems with my computer, in the future.  The service would cost me $150 with 1 year tech support 24/7 from "iYogi" (support for Netgear tech. company) or $50 to do it once.  There was a LOT of pressure to pay then and not wait a day or more so I could think my 90 days of Netgear Tech. Free support ends on Thursday, November 22, 2012.  The person of 'iYogi technical support', Abdullah, said that because my Toshiba laptop has 4 GB of RAM and the Netgear wireless router has a very small RAM, then in a near future the problem could happen again and I have to pay a lot of money for the correction of a problem including my registry corrupted 9% of my Windows 7 (Home Premium (64-bit) with Service Pack 1).

  I had no problems with my computer that I've known since the purchase of this new about 2 years (a portable satellite youcef) ago.

  I have to have my system "optimized"?  My really register 9% damaged and if yes, is this normal or do I need to have it fixed?

  I was wondering if I had another brand of a router (for example the Linksys), I have the same problem?

  I would be grateful to anyone who helps to answer my questions and all the other advice on this subject.

  Thank you, or anyone in advance for all your help.

  Kind regards

  CCEntertain2M

  "Registry was damaged and needed optimization" - complete garbage, if the registry is damaged the PC does not start, the registry requires no optimization, third party that claims to optimize the registry software is snake oil and in the worst cases can make the system unusable.

  Usually if you have a router problem appear, of the first steps would be to reboot the router (unplug his pwr for a minute) and re start the PC. These steps are usually all that is necessary.

• END point URL for the routing service BSE says not FOUND

  Hi all

  For services of routing in BSE, the WSDL link opens the fine, but the link to endpoint URI for the routing service fails with the message below the message. When I invoke the WSDL with SOAP UI, I'll be back the same error message. I tried to bounce the server, but no help. I also noticed that this slide ESB_Projects Directory gives error 404 on any browser.

  Then, when I click below url for all the routing service

  http:// < hostname >: < port > /Event/ < systemName > / < serviceGroupName > /AddressStandardizeRS

  I get the error in the browser - below

  Not found

  The URL /event/ requested < the system name > / < group name > / < Routing Service name > was not found on this server.

  Oracle-Application-Server-10g/10.1.3.1.0 Oracle-HTTP-Server Server at odevsoa.local1.wbcgp.com Port 7777

• Web Service data control the result as a basis for workflow router

  Hello
  
  I'm under JDEVADF_11.1.2.3.0_GENERIC_120914.0223.6276.1 build
  
  I want to use the result of a check of SOAP Web Service data as input for a router on a workflow; lines will only ever return 0-1 control of data.
  
  Is it possible declaratively on the workflow diagram by simply using a SOAP data control, or should I access the data control through a managed bean, or go on the road of web service proxy?
  
  I'm new to ADF some detailed guidance would be appreciated.
  
  Thank you very much.

  Hello

  routers can have their own binding ADF file, so yes its possible. Select the router and then use the right button of the mouse to go to the pageDef file. As it does not exist it will be created. Then add a method binding point to the method on the WS to invoke domain controller. In the router, you should be able to use #{bindings.methodName.execute} as the EL. If the method returns a value, then it went to the assessment.

  However, if you need to look at an iterator (returned collection) then you are binding the attributeValue to one of the attriibutes in the collection. This should also configure the WS iterator and the required method binding

  Frank

• Announcement of network user VPN via eigrp route

  I can't have the VPN client user network advertising via eigrp, here is what I have so far. 10.55.1.0 is not announced.

  Router eigrp xx

  No Auto-resume

  no default - information in

  no default-information

  by default 10000 100 255 1 1500 metric

  Network 10.55.0.0 255.255.255.0

  Network 10.55.1.0 255.255.255.0

  passive-interface default

  no interface passive inside

  redistribute static

  I already have about 30 static routes and they have redistributed successfully, the only way I can think to announce that the VPN, it is inside the neighbor is using a card of route-attached to the static method redistribute. The ACL roadmap would then 30 networks of the static routes in and the VPN. I really don't want to do that. Because every time someone adds a new static route, they would also have to be added to the ACL for the road map. Any ideas appriciated.

  Hi Matthew,

  Please, add the following command under your dynamic crypto map:

  test of dynamic-map of crypto-map 10

  the value reverse-road

  HTH.

  Portu.

• Satellite L350 - access code for the router

  Dear Sirs

  I have a Toshiba Satellite L350 under Windows 7 Ultimate. For the first 5 months, he remembered the wireless to the router access code. I then installed a BT Home Hub which I subsequently removed and then the Windows 7 machine will remember is no longer the password.

  I spent hours on the phone with Microsoft without success. Can anyone help?

  Hi Peter Kellard,.

  For the moment I put t understand your problem.

  What happens if you enter the WLAN (access code) key again? Can you connect?
  You could save it again ;)

• Limit the bandwidth for WNR614 router n300 wireless devices

  Hello

  I use the WiFi WNR614 N300 router. Is it possible to limit the bandwidth for devices that are connected on it.

  I thank you,

  Vignesh C

  Hi @vic2408

  Welcome to the community!

  To answer your question, there is no way to limit the bandwidth on each of the devices.
  You may need to use a 3rd party software to do this.

• HP laptop computer 635: need driver for wireless router

  Hello. I had to replace the hard drive of my laptop computer and a new operating system, Windows 7 Pro, after which it cannot connect to the wireless router. It's a router Westell A90-750018-07. I have a Tablet Android working on this particular router and want to download the driver on it and put it on the flash drive to reinstall on my laptop. Is that going to work? Where can I download it? FairPoint is now 14.99 an extra month of me now for a Support technique Premium. They are waiting for me to borrow a laptop to try to help him to do so. They seek to use the android on the phone, but it seemed to complicated with android as a third party. Will this work? Please if someone could help would be great. Thank you.

  You need the driver for the card installed in your 635 wireless. Problem is that you will know which card you have Ralink, Realtek or Atheros. The drivers are all posted on your support page:

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5086540&swLangOid=8&swEnvOid=4059

  If you don't know what wireless card, you need to get the id of the hardware in the Device Manager. Right-click the network adapter, choose Proprietes.dans the window that opens click on the Details tab use the selector drop-down menu to choose the hardware id. After the first string of numbers - or at least the first half of the chain.