IPhoto opens briefly then goes down?

Similar Questions

• VPN appears briefly, then goes down

  Hello

  I test on VPN with my Cisco 1801 router that uses an on FA1 ADSL modem to connect to Internet. This port is assigned to 80 of VLAN.

  I have configured the modem to forward all ports to the Cisco and the Cisco is connected to the rest of my LAN on FA2

  Whenever I try to use my Android phone to connect to the VPN, it tries for a while then just goes back to the disconnected state.

  The phone works with other VPN services, I've tried.

  I use the same references that I use to connect to the router, but have also tried the chap credentials defined in the virtual model.

  When I turn on debugging events VPN, I get the following result, which seems to show that the connection comes up

  VPDN Received L2TUN socket message 
  VPDN uid:2 L2TUN socket session accept requested
  VPDN uid:2 Setting up dataplane for L2-L2, no idb
  VPDN Received L2TUN socket message 
  VPDN uid:2 VPDN session up
  VPDN uid:2 disconnect (AAA) IETF: 17/user-error Ascend: 26/PPP CHAP Fail
  VPDN uid:2 vpdn shutdown session, result=2, error=6, vendor_err=0, syslog_error_code=8, syslog_key_type=1
  VPDN Received L2TUN socket message 
  

  Here is the frame configuration that I use...

  vpdn enable
  !
  vpdn-group homevpn
  ! Default PPTP VPDN group
  accept-dialin
  protocol pptp
  virtual-template 1
  l2tp tunnel timeout no-session 15
  !
  interface Virtual-Template1
  ip unnumbered FastEthernet1
  ip nat inside
  ip virtual-reassembly in
  peer default ip address pool VPN-pool
  no keepalive
  ppp encrypt mppe auto passive
  ppp authentication chap eap ms-chap ms-chap-v2 pap
  ppp chap hostname vpntest
  ppp chap password 7 ****
  !
  ip local pool VPN-pool 192.168.1.10 192.168.1.15
  

  Thanks for all Child1

  The reason is that, with CHAP, the router receives a response that is based on the hash of the password. To validate the fact that, the router requires the password in clear text and can not use one is configured with "... secret user name.

  Another option is to authenticate with PAP, where you can store users with hashed passwords. Simply choose whether you want passwords in clear text in transit (PAP) or on the router (CHAP).

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• IPhoto opens but then closes unexpectedly after 10 seconds. What can I do?

  My iPhoto opens but then it unexpectedly closes after a few seconds, I can't upload photos. What can I do about it?

  What version of iPhoto? What version of the operating system?

  Is it iPhoto and 10.8 v9.2.3? If so:

  A lot of older versions of iPhoto 11 this meet right now:

  Huxly647 discovered this fix

  1 goto /Applications/iPhoto.app/Contents/Resources

  2 delete the files 'googlemap.html' and googlesearch.html

  IPhoto no longer crashes, site does not work, but it doesn't bother me too much.

  If it is not on this version, then back with more details.

• Downloaded first Pro CC opens briefly, then crashes with "Adobe first Pro CC stopped worki.

  Downloaded first Pro CC opens briefly, then crashes with the message "Adobe first Pro CC has stopped working".

  Make sure all your drivers are up-to-date.

• iMovie 11 starts to load then goes down, worked fine yesterday.  What's wrong?  Should I reinstall?  I'm in El Capitan

  Just made my first film on iMovie 11 to show the new apple TV.  Worked well started a new project two days ago, but now when I try to open iMovie it starts with 'validation library iMovie on computer' and then seems to load the last project I worked on, (I can see the clips) and then it just stops.  Then the problem page, and even if I select Reopen, the same series of events occurs.  Does anyone know how to fix this?  It is strange that it worked before and I haven't added anything on my Mac.

  You may have a corrupted project.  Try iMovie with the alt (option down key).  This prevents automatically trying to open the last project and may allow you to access other projects or even the problem.

  Many people make problems of running iMovie 11 (= 9 version) State under El Capitan.  I recommend you to consider upgrading to version 10.1

  Geoff.

• When I click on a link in Twitter, Facebook, other, page opens but then goes to Yahoo search. How do I kill who?

  I have Google as my default search engine. When I'm in a number of sites and click on a link to open it, the page opens, but only momentarily, and before moving to the browser of Yahoo search for this topic. I would like to prevent that from happening, but don't know how. I'm on a Mac Book Pro OS 10.9.5. This was not the case before the switch to Yahoo as search engine default Firefox.

  Thank you

  Email address removed by the moderator. If please do not publish sensitive information and follow the guidelines and rules of the Forum

  Favorite and use this.
  Download the Mozilla search reset {web link}
  This module is very simple: when installing, it backs up
  and then resets your search and home page preferences
  at their default values and then to uninstall. This
  affects the search bar, search bar URL, and the home page.

  https://support.Mozilla.org/en-us/KB/how-to-fix-preferences-wont-save

• Firefox opens briefly, then crashes when I click on a link in Thunderbird message. If Firefox is already running, no problem.

  Latest version of Firefox (23.0)
  Version of Thunderbird 2.0.0.24
  Problem b/c safe mode event cannot have with FF open automatically when you click on an e-mail link.
  The last of many crash report numbers:

     Crash ID: bp-6e0133b7-430e-495c-88b8-61a762130807
  

  The latest version of Thunderbird is 17, update for it.

  • www.mozilla.org/Thunderbird/

• FB does not open on my iPad after my upgrade of the OS to 9.3.2 he starts to open but then returned to the screen.

  I just transferred most of my photos which prevented me to upgrade my OS. Now, the upgrade is complete (9.3.2) FB starts to open but then goes back to the desktop. Same thing for my YouVersion Bible. I thought maybe I could uninstall FB and reinstalling, but see how.

  To remove Facebook and YouVersion bible app, tap on and hold the icons (one at a time) until it wiggles. Then press the X in the upper right of the icon. Go to the App Store to install their return.

• Windows XP, Outlook Express, IE email link starts to open, then shuts down

  When I click on the link, IE starts to open, then shuts down.  If I then click on IE, dialog box opens with the statement that the last session closed unexpectedly, what I want to restore the last session or go to my homepage.  If I click on prompt to restore last session, IE opens the link which was stopped.

  See if this helps: http://iefaq.info/index.php?action=artikel&cat=48&id=133&artlang=en

  Steve

• The first cc was going well until the last update you want to open and then throws a sign indicating that the application could not start properly (0 x 0000142) and the program does not open

  The first cc was going well until the last update you want to open and then throws a sign indicating that the application could not start properly (0 x 0000142) and the program does not open

  
  

  Hi Marcelo,

  You may need to check this: Re: Premiere Pro 2015 won't open after the recent update

  Kind regards

  Navdeep Pandey

• 851W w / WPA - PSK - Interface goes down.

  Hello

  I tried to configure WPA - PSK on the router 851W. I followed the instructions using the SDM and properly active wireless WPA - PSK network. I have connected a MacBookPro to the network wireless, with all the features, then after a minute or two, separates the client and Dot11Radio interface goes down.

  I have install a network open without any connectivity problems. I have search the net and forums of Cisco without success for a solution to this problem. Here is the link to the guide: http://www.cisco.com/en/US/products/hw/routers/ps380/products_configuration_example09186a00808acf2f.shtml

  Any ideas what might be causing the radio interface down with WPA - PSK configured?

  Thank you.

  For some it's IOS version WPA - PSK, which proved to be intermittent. Cisco CSCeh90412 bug describes it. Try to update the IOS version and check.

• Volume, keep going down

  My cursor of volume under windows 7, keep going down and I tried to change the communication for the 'status quo', but still not working please help me

  Hi GordonCheng,

  (1) since when are you facing this problem?

  (2) remember to make changes before this problem?

  (3) what is the number of brand and model of your computer?

  Method 1: Uninstall and reinstall the \audio card drivers:

  You must be logged on as administrator to perform these steps.

  (a) open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.

  (b) If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  (c) in Device Manager, locate the sound video and game controller, and then double-click the device name.

  (d) click the driver tab and then click on uninstall the driver, and then follow the instructions.

  Click on the link to re - install the drivers manually

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  For more information, see the link below

  Tips for solving common audio problems
   http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

• Qomsio F60 - 10 K - fan runs at 90% for 20 seconds, then goes to 50%

  Hello, I bought laptop before about 11 months and today, I got an error :)

  My laptop fan working at 90% in Windows I have does not work any game quite normal in the Windows 7 Desktop, and fan is 90% about 20 seconds, then going to 50-60% and after 1 minute still on 90% and like this all the time.
  Where is the problem?

  Hello

  Eventually, the temperature increases to a level where the fan must be operating at 90%.
  Then, the temperature falls down due to faster air circulation and so the fan runs slower. Then the temperature rises again and this cause a stronger fan activity.

  Maybe the portable computers vents are clogged with dust or debris.
  I think you first need to clean the fan using a jet of compressed air and it should test again.

• How can I manually enable Asus Smart gesture again? It turns off everytime I open and then close it.

  I updated the drivers I can find related to the smart move, but everytime I open and I shut down my computer, the smart move goes off sometimes and doesn't work on the other time. If she goes out once, I have to restart the computer before I can use it again, hoping that after I closed my lap top and open later, it will still work. He died in each 3-5 times I shut down my computer and it's extremely annoying.

  I updated the drivers I can find related to the smart move, but everytime I open and I shut down my computer, the smart move goes off sometimes and doesn't work on the other time. If she goes out once, I have to restart the computer before I can use it again, hoping that after I closed my lap top and open later, it will still work. He died in each 3-5 times I shut down my computer and it's extremely annoying.

  Hello

  It is an Asus product, you must contact the Asus technical support for help.

  ASUS service | North America:

  http://www.service.ASUS.com

  Concerning

• I installed G10-ebook but when open it and write down the username and password it starts and stops immediately and closes what should I do?

  I installed G10-ebook but when open it and write down the username and password it starts and stops immediately and closes what should I do?

  Hello

  Step 1: Check if the problem persists in the clean boot state.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  1. click on start and then click Run.
  2. type msconfig and click OK.
  The System Configuration Utility dialog box appears.
  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Step 2: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.

  Reference:
  Using the event viewer
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_event_viewer.mspx?mfr=true

  Understanding of event viewer
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/event_overview_01.mspx?mfr=true

  Procedure to view and manage event logs in Event Viewer in Windows XP
  http://support.Microsoft.com/kb/308427