Is the iI require a router with my PIX?

Similar Questions

• How can I set up the AEBS as a router with sky Hub as a modem?

  I have sky broadband with a Hub of Sky SR102-Z router. I had the problems of slow speed, and the tour engineer told me that it is caused by the interference of a wi - fi connection. I have an Airport Extreme Base Station that I stopped using when I got sky, but I now use it as a router (the Hub of sky is quite limited) connected to the Sky as the Modem concentrator. I would be grateful for any advice on how to set up the AEBS so that it fills the air Hub. Thank you.

  I would be grateful for any advice on how to set up the AEBS so that it fills the sky Hub

  If you want to use as a router AirPort Extreme... it would mean that hub Heaven must be reconfigured to act as a modem mode simple bridge.

  Whether or not it's possible and even if it is possible... Whether or not the sky will support this type of installation are questions for heaven. So, you will need get clarification from heaven on this topic before you can proceed with the configuration of the AirPort Extreme.

  You can keep in mind that the hubs of some suppliers cannot be reconfigured to make the function of the device as a modem mode simple bridge. If which is the case with the sky... then you will need to set up the AirPort Extreme in Bridge Mode and continue to let the Sky router as the network router, same function if the wireless may not be enabled on the hub of the sky.

• With the help of port security with Failover PIX

  Hello

  I want to configure port security on a switch in which a pair of PIX failover are configured. However, after

  http://www.Cisco.com/univercd/CC/TD/doc/product/LAN/cat6000/12_1e/swconfig/port_sec.htm

  It seems that this is not possible due to the PIX swapping MAC addresses: "If a workstation with a secure MAC which is configured or learned about a secure port address tries to access another secure port, a violation is marked."

  Does anyone know of a way around this?

  Many thanks in advance,

  Matt

  Hello Matt,

  Unfortunately it not there no work around to your problem.

  Thank you

  Renault

• Access to the COR to two XP systems behind a router with a single public IP address

  Hello

  is it possible to access the RDC to two XP systems, with two different port for the DRC, behind a router with a single public IP address?

  Please note this ia a small home network without any parameters of the field. I use IP to access DRC.

  You comments are appreciated.

  Thank you

  Use different ports for the DRC on both XP and configure the router to redirect to the appropriate port on the appropriate computer.

  See the article in the Microsoft Knowledge Base How to change the listening port for remote desktop .

• IOS router with several groups of VPN

  Similar to a discussion, I read with a PIX firewall, I need to set up multiple VPN groups on IOS-based router to support different levels of security. For example, a VPN "GUESTS" group would only have access to 1 server, while the VPN "ADMIN" group would have access to the entire network.

  With a PIX firewall, you can simply specify additional group names (for example "group1 vpngroup',"vpngroup group2"and so on). However, I have not been able to find how do with IOS-based router (Cisco 831 12.3 (4) T) running.

  For example, I have these dynamic groups of VPN:

  the crypto isakmp client configuration group of GUESTS

  password1 keys

  DNS 10.1.1.1

  swimming POOL1-IP pool

  Configuration group customer crypto isakmp ADMIN

  key password2

  DNS 10.1.1.1

  POOL2-IP pool

  ! - Users get authenticated to a RADIUS server

  list of card crypto CRYPTOMAP customer VPN-USER authentication

  ! - The problem is that line taken out. "I can only specify an allow list (a group name) for this encryption card!)

  card crypto CRYPTOMAP ADMIN isakmp authorization list

  I did research on this site, Google, usenet and ORC and have not found what I'm looking for. Any ideas?

  Thank you.

  Command 'isakmp authorization list' you do it reference does not refer to the VPN group, it refers to a whitelist of AAA name which States that the groups are configured locally. Change to the following:

  AAA authorization groupauthor LAN

  card crypto isakmp authorization list groupauthor CRYPTOMAP

  The "groupauthor" is just a label that matches the encryption to the aaa command. Your clients VPN will be accompanied to a specific group depends on what group name, they set up in their VPN client.

  See http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080095106.shtml for details, it's a HW 3002 client to a router but the router config is exactly the same thing.

• When you try to add a network route with the "route add" command in the command line, I get the message "the requested operation requires a rise."

  Elevation required to route add command

  When you try to add a network route with the "route add" command in the command line, I get the message "the requested operation requires a rise."  What is the correct syntax to use?

  You can watch using the PowerShell...

  http://TechNet.Microsoft.com/en-us/library/bb978526.aspx

  http://TechNet.Microsoft.com/en-us/scriptcenter/dd742419.aspx

  .. .and post questions about Windows PowerShell forum...

  http://social.technet.Microsoft.com/forums/en/winserverpowershell/threads

• How can I reset my "authentication required" username and password? The fields are always filled with my old information.

  How can I reset my "authentication required" username and password? The fields are always filled with my old information.

  Follow these steps to delete the recorded data (form) in a drop-down list:

  1. Click on the (empty) input field on the web page to open the drop-down list
  2. Select an entry in the drop-down list
  3. Press the DELETE key (on a Mac: shift + delete) to remove it.
  • Tools > Options > Security: passwords: "saved passwords" > "show passwords".
  • http://KB.mozillazine.org/Deleting_autocomplete_entries

  You may need to clear cookies from this site, so if you checked a box to remember you.

• You are about to open a session "keiron.me.uk" with the user name "Gerry" site, but the site requires no authentication. Maybe it's attempt to deceive you.

  http://Keiron.me.UK

  This very annoying message what I select my site

  You are about to log on the site "keiron.me.uk" with the user name "Gerry", but the site requires no authentication. Maybe it's attempt to deceive you.

  It is ok with Internet Explorer

  To resolve this problem, simply is to remove all bookmarks you have to keiron.me.uk and then re-create by vising the site by typing the address directly into the address bar.

  If you want to manually fix it then, check the properties of the location of all bookmarks that you have for keiron.me.uk. It is probably similar to http://keiron:[email protected] remove the keiron:password @ section and the dialog box should not appear again.

• R7000 as router with the router for mobile broadband Internet

  Hey guys. First of all, my apologies for my somewhat inadequate English skills. Secondly, I am brand new to the community, so apologies in advance for any fault :-) Third stop, apologize for having a complete beginner :-D

  So, for the issue: I recently bought a router top mobile broadband 4G (4 G MBR) to my apartment, because of the gap of strength and speed signal very low quality of the cable to the ground on my Street (fiber is to come next year).

  But the router provided by my operator isn't on par with my router R7000 Nighthawk when he comes to reach wifi, wifi speed, number of outputs of LAN and power of the processor.

  So, I want to use my R7000 my router, the internet signal from the air to the 4G MBR, then by cable to the WAN of the R7000.
  In other words; I want to just 4G MBR to simply pass / transfer the internet signal to my nighthawk R7000 router so I can use the R7000 as my router, LAN and wifi.

  How can I set this up?

  Thanks for your help!

  Update: the MBR has been no help at all. As far as I could tell, there is no possibility to bridge or pass-through mode. The R7000, as she does the work. I just put it in AP mode, adjust all the wired connections DHCP/auto IP assign and everything works great.

• Lost password administrator somehow. Tried to reinstall Windows XP with the CD without success. Want to know how to get around the password requirement.

  Cannot start; or work from the recovery console because of the lack of administrator password.  There were periodic crashes which led me to try reinstalling XP.  Now I'm stuck when I get to the password requirement in the Recovery Console.  As you can tell, I'm not computer literate, but can follow written instructions on how to recover from this.  Also, would like to know how to recover my files and programs if they are not lost; or how to determine if they are.

  gchtm5,
  Thanks for posting with us.  If you no longer have the administrator password you can perform a parallel installation so that your data will not be lost.  However, you will need to reinstall your programs.  This link covers the different installation options.
  http://support.Microsoft.com/kb/316941

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to change the SSID name of the computer to be Compatible with the new name SSID router

  Need to change the default name of the SSID router and then reconfigure adapters wireless in each PC to be compatible with the new router SSID.  A PC has Windows XP Home Edition Version 2002 Service Pack 3 and the other Vista Home Premium.  What are the steps to change the SSID on each PC?  Your response will help complete a home network wireless system.  Thanks in advance.

  Hello

  Your computers use the SSID of your router - sound essentially its name.

  Check this box:
   
  Setting up a wireless router with Vista
  http://www.ehow.com/how-does_4899098_setting-up-wireless-router-Vista.html

  If necessary:

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  Setting up a wireless router with Vista
  http://www.ehow.com/how-does_4899098_setting-up-wireless-router-Vista.html

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• Unable to connect to the router with Win 7

  I can't connect to my router with os Win 7. I have XP & Vista partitions on the same machine without any problem. Keeps giving me the default ip address 169.254.   I did the release, renew, map unistall, policy changes, the static settings and just about everything else I could think of. It is connected at a given time, but not anymore. Same router. My HP mini with Win 7 has no problem of wired or wireless connection. Is there a registry editing as I do or other settings I can try. I disabled V6 and others. Any help would be appreciated. Thanx.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• This computer does not meet the minimum requirements... when installing graphics Intel HD 4000 for my Dell Vostro 5560 with Windows 7 64 bit

  In recent days, I reinstall Windows 7 to my Dell Vostro 5560 and this laptop does not have a driver CD, I downloaded all the required drivers for my laptop directly from the Dell Support Web site. I started to install a step by step. Chipsets, Audio, network, MEI, etc... However, once I try to install graphics, this laptop comes with 2 graphics card, an Intel and another is Nvidia. So, I try to install first Intel. When I click on the exe file, a message box appears saying that «this computer does not meet the minimum requirements...» ». Why is - what happened? I'm sure that my laptop include Intel graphics. Please help me as soon as POSSIBLE. I want to install Windows 7.

  Some drivers of today require at least Microsoft .NET Framework 4.5. Is this possible?

  It is certainly. AMD demanded 4 .NET. x + for their installer drivers for several years already, but I think they have started including with their driver downloads recently.

  -I never noticed if Nvidia use .NET with their drivers Installer, install but .NET 4.5.

  Download Microsoft .NET Framework 4.5 of the official Microsoft Download Center

  .

• [SOLVED] Problem with the ACB and InterVLAN routing

  Hello.

  I have Cisco 3750 G with IOS k9 - mz.150 - 2.SE4 Service of intellectual property. In my network, I have 4 VLANs with 4 internet gateways. I have set 4 static route for each gateways and with PBR to match this static routes. If I use "set ip next-hop" all traffic goes through the specific gateway interVlan routing does not work (I need to because the customers interVlan routing in different VLANS must be), and if I use 'set ip default next-hop', I was incapable of it attributed to Vlan (road-map lan14 not supported based on routing strategies).

  Model SDM is on the road that ip Routing is enabled.

  Here is my config for 2 of these VLANS:

  interface Vlan7
  IP 192.168.7.254 255.255.255.0
  IP access-group 107 to
  !
  interface Vlan14
  IP 192.168.14.254 255.255.255.0
  IP access-group 114 to
  !
  IP http server
  IP http secure server
  !
  !
  IP route 0.0.0.0 0.0.0.0 192.168.70.254
  IP route 0.0.0.0 0.0.0.0 192.168.140.254
  !
  access-list 107 permit udp any eq bootpc any eq bootps
  access-list 107 allow ip 192.168.7.0 0.0.0.255 any

  access-list 114 permit udp any eq bootpc any eq bootps
  access-list 114 allow ip 192.168.14.0 0.0.0.255 any

  lan7 allowed 10 route map
  corresponds to the IP 107
  IP 192.168.70.254 jump according to the value
  !

  lan14 allowed 10 route map
  corresponds to the IP 114
  IP 192.168.140.254 jump according to the value

  !

  Where is my error in config?

  Please help me, I'm stuck here almost three weeks.

  Hello

  You have created courses 2-card to set the next hop for a portion of the traffic classified with an acl.

  If you want any other traffic manager you must create an empty instance of your roadmap

  Example:

  lan7 allowed 10 route map

  football game...

  map of route allowed lan7 20 ==> Add this instance and leave it empty. You say the switch/router that he must refrain from other traffic but nothing to apply.

  Hope that this clear.