Is there a VI for USB-6008 who works in LV7.0

Similar Questions

• Do another counter for usb-6008 VI using Labview 8.5

  I want to create another counter for usb-6008 using Labview 8.5, it is necessary to calculate the two gears simultaneously.

  The best way to proceed is to use the meter.  The counter counts
  signals without having to interrupt the system or use the USB bus.
  When you ask the number of ticks that saw the meter, one
  request is thrown from the CPU to the USB line to the 6008, which then
  request counter "ticks how have you seen?  This number is
  returned on the USB bus, goes to the CPU and display on your
  screen.  Given that the DIO lines on the 6008 are software timed, it is
  no way to guarantee that the data back to the central unit is
  deterministic.  The conceptual difference between software-controlled
  DIO (that nondeterministically returns an entire stream) and a
  meter software-tick-application-controlled (which returns a unique number
  with the number of ticks) prevents us from using the DIO lines on the
  6008. the best way to count more edges is buying more 6008 s.
  Another possibility would be to buy a PCI card to counter such as
  the PCI-6602, who owns 8 counters. Most of the counters we offer in the
  USB form factor is 2 per device.

• Is there a HCL for USB?

  Hello

  is there a HCL for USB, install ESXi 5.1 on it? I want to assure you, that I have allways have a supported vmware environment.

  Thanks and greetings

  Michael

  Yes, see this article;

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1021345

  With the help of USB devices that are not in the list of devices supported

  If a USB device isn't on the list supported, set up a test environment with ESX/ESXi hosts and virtual machines to reproduce your production environment. Set the USB to the ESX/ESXi host and add it to the virtual machine. If the operation of the USB device works as expected, you can attach the USB device to a host ESX/ESXi virtual machine and production.

  These USB devices are not available for passthrough:

  • USB devices such as mice and keyboards that have a HID bootable interface.
  • USB devices such as cameras video real-time and audio devices that use isochronous data transfers.
  • USB devices that installed an ESXi host. For more information, see VMware for devices USB/SD used for the installation of VMware ESXi (1010574).

  Post edited by: jrmunday

• Love at first sight for usb cable will work for migration?

  Love at first sight for usb cable will work for migration?

  Migration from what to what?

• Try to find the PLUGIN for SUPERAntispyware Pro who works as a site im headed to does not work.

  I have SUPERAntispyware Pro on my PC when I choose the option on the program to "see what is running on my PC", it goes to a website to get the plugin but then says cannot install the plugin or something in that sense.
  I use FIREFOX v3.6.10 and SUPERAntispyware program is v4.44.1000

  He is a former plugin - 09-2007 - and is missing the file install.rdf 'modern' that requires Firefox 2.0 and later versions.
  
  http://www.SUPERAdBlocker.com/ActiveX/sabffx.xpi

  See SUPERAntispyware support for help on this issue.

• My old reliable 16 bit BACK interpreted (and not compiled) program, an add-on for Angoss Smartware, who worked for years in XP has stopped working

  I have a spreadsheet, database, wordprocess modules DOS base program and that it is a programming language with which I programmed an accounting software package among other things. In recent weeks it does not my code. One machine said parity memory error and stops, another machine said variable file does not. I can load my original spreadsheet and database of the 16 bit BACK exe files but not inside my code 'interpreted '. The actual data and spreadsheets, loading files and can be changed. I tried to recompile from source code that I wrote and Windows no longer allows that. The software name is Smartware II and executable is angossx.exe if anyone is familiar with it.

  This program worked from a file of DOS commands, with a pif associated with the executable file and the autoexec and config files in windows\system32 for many year starting with Windows31...

  I suspect a recent update of security in Windows caused my code to look like rogue code. Anyone have any ideas on a solution?

  Hi aurelienbazin,

  Thanks for posting in the Microsoft Community. The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  Hope the helps of information. If you need help, please answer that we will be happy to help you.

• Audio guide for streets & trips 2006 does not work for Vista. (Who worked for XP)

  Guide audio of streets & trips 2006 worked for xp.  new laptop w/vista.  does not work now.

  http://www.Microsoft.com/communities/newsgroups/en-us/default.aspx?DG=Microsoft.public.streets-trips

  Discussions in Streets and Trips

  In addition to the info below, try the Streests and travel above Newsgroup.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

  Windows Vista Compatibility Center

  First thing to do is to check its Vista compatibility at the link above, and if not to see what patches/solutions are available from its manufacturer...

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

  If this is not Vista compatible, read the info on the link above.
  It works for some programs, but not all.

  This applies to software programs, NOT hardware drivers.

  If it's Vista compatible > uninstall it > Re-download/save to your desktop > right click on setup.exe O run as admin.

  See you soon.

  Mick Murphy - Microsoft partner

• USB-6008 LabVIEW 2011

  Hello

  I can't find any solution so that my usb usb-6008 interface works on LabVIEW 2011, DAQmx Wizard is missing and I can't find any comparable VI!

  Someone at - it an idea?

  Simon

  Have you installed the DAQmx driver after installing LabVIEW?

• AO. MaxRate, AO. MinRate, AO. Properties of voltage. RNGs for hardware DAQ USB-6008

  Hello

  in one of my report, I use the AO. Property of Voltage.Rngs to see if the selected DAQ card takes in charge the application voltage range. This works very well for my PCMCIA card as well as a PCI card. Now run the same VI with a USB-6008 device, this property gives all the return values. In addition, the report of AO.max.rate and AO.min.rate of the '0', the output is-200197 error properties. I use DAQmx as it is supposed to support the same functions for all DAQmx devices. Can someone please tell me what wrong here and how can I get around this?

  Best regards

  Gabs

  AO.min.rate and AO.max.rate are 0 and error-200197 back because the USB-6008 case supports the outputs analog hardware timed.  The description of error is "device does not support this property."  There is an entrance to the knowledge base for this question.

  By selecting 'Use Waveform' uses the synchronization of the sample clock.  The waveform data type specifies a delta t, which is used to set the sample clock frequency.  It is not supported on the box USB-6008.  You shouldn't set your calendar of sample type or explicitly assign the "On Demand".

  The DAQmx driver supports hundreds of different devices.  Not all combinations of properties are valid for all devices.

• DAQ USB-6008 will be able to power and record voltage for UMS T5 blood pressure at the same time?

  I would use my NI USB-6008 to power my blood pressure monitor UMS T5 (http://www.ums-muc.de/en/products/tensiometer/t5.html) but also to take readings of it, but I don't know if it's possible to do it properly. The power supply for the instrument can be as low as 5V, I can easily get the dedicated + 5V channel. I'm able to feed the instrument and connect it to an analog input on the 6008 and measure a voltage in differential mode. However, when you read the documentation of support for the instrument, I find the following:

  "Potential pitfalls of data acquisition: the pressure transducer is configured in a full Wheatstone bridge, the input voltage and mV signal output can be connected to the same reference (mass)." Therefore, the mV output signal can be measured using a differential voltage measurement. Therefore, do not make an asymmetric measure of pressure transducer mV output. "(http://www.decagon.com/assets/Uploads/MeasuringUMSTensiometerswithnon-UMSControlandDataAcquisitionSystems.pdf)

  My understanding is that the 6008 can take a differential measure if I attach the signal '+' and the signal "-" to the analog inputs of positive and negative terminals. However, it seems that all the ports of ground on the 6008 are grounded to the same reference, which would make my measure of invalid tension according to the above paragraph. So my real question is: if I try to record the voltage with one of the analog inputs on the 6008 in this way, is the valid measurement? Or I need to find a separate power supply, with a different reference field to ensure that the measure is accurate?

  The technical details of this device is very poor. The manual is not much better. Companies that want to sell scientific equipment should publish decent cards or get out of business.

  In section 3.4.3 General requirements the device is described as a "bridge not amplified circuit.  This information along with the impedance of the bridge should be in the specifications, because it is essential to apply the device under any circumstances other than the nominal behavior in 10.6 V.

  The answer to your question is:

  You can use it with the box USB-6008.  The 5 V supply will result in output voltages a little less than half (5/10.6) the voltage specified in nominal conditions. You can use the differential input mode on the box USB-6008.  The absolute input voltages will be approximately 2.5 V with the 5 V power supply. This voltage is in the range of the aircraft. The differences are likely to be less than 100 mV. The resolution of the USB-6008 on the + /-1 V is located about 0.5 mV so your resolution of pressure will be about 1% of full scale. The voltage input impedance and termination of the USB-6008 will present a few errors.  These can be in the order of 5 to 10%. I can't predict much better without the missing bridge impedance specification.  These errors should be relatively constant and systematic. A calibration of the whole system - sensor and together hardware DAQ should allow you to compensate for a large part of this error.

  Lynn

• Looking for a way to mount an acquisition of data USB-6008

  Anyone has a suggestion for an acquisition of data USB-6008 mounted on a Panel. I use it for a system where it should not be loose. I have a few ideas, but hope that someone smarter already has a good solution.

  Thank you

  It is not a robust application, but the box will be moved and I don't want it put in the open air. I simply put a velcro pad on the back and the atttaching in this way. Should be all I need.

• Population of list for the NI USB-6008 channel

  Hello

  I use labview version 2011. I have worked with USB 6008 for two months, but I encountered an error constantly even if I restart or shutdown of the PC for a while. I connected to my channel 6008 AI0 asensor and DAQ Assistant is not populating the available analog channels. Please someone help. Since it worked fine for a month, but not today.

  History was end I solved my problem after seeing the "Error in the knowledge base" pecautions on the site of NOR. Now the help data acquisition work.

  But I wonder how MAX data are linked with these DAQ contest. Some can clear me how MAX is related with all these functions of time real Labview.

  By the way, I'm using labview for two months.

  Thank you very much.

• Amplification of Type K Thermocouple for playback with USB 6008 at high temperature

  I'm looking to amplify a K type thermocouple, so that the signal can be read with a bit of precision by a USB-6008. I watched the AD595 chip, but it indicates a maximum useful temperature of 100 ° C and I'll need to read up to 700 C.

  Is there another amplifier chip that would work up to this temperature, or should I resign me to use the unamplified signal and get a very inaccurate (~ 30/division) the temperature reading?

  The AD595 has a range of-200 C to 1250 C, here is the data sheet:

  http://www.MNE.PSU.edu/Sommer/me445/AD595.PDF

  -AK2DM

• not able to install the driver mx NIDAQ (for the use of USB-6008) in my laptop, NIDAQ902f0? any solution...

  I am not able to install driver of mx NIDAQ (for the use of USB-6008) in my laptop,... well NIDAQ902f0 want to give any suggestion...

  Following message comes when I run the Setup... (installation program downloaded from the website OR..)

  Runtime error:

  This application has requested to terminate in an unusual way.

  Please contact the application support is more information.

  Title of the dialog box is "Microsoft Visual C++ runtime library"

  Is the same when NIDAQmx 7.5 is tried to install from the CD that came with the USB-6008.

  Double post

• My USB-6008 has bad firmware for c# application, utility switch fails.

  I use a pair of USB-6008 in an application. Everything was fine until what I installed the driver NOR-DAQmx. This software has changed the firmware of NOR-DAQmx BASE of NOR-DAQmx. The problem is that I can't change it back again. The OR errors of the utility of switching because it cannot find the Labview engine. Well, it will not be as I am not a user of labview.

  Hello Drew,

  The simplest solution would be for you to download and install runtime LabVIEW 8.5.1, with which you will be able to run the utility of switching without problem. It of free and can be found here:

  LabVIEW Run - Time Engine 8.5.1 - Windows 2000/Vista x 64/Vista/XP

  Let me know if you encounter other problems.