Issue of RADIUS and AD

Similar Questions

• RADIUS and Ganymede + running simultaneously?

  I have a Secure ACS 5.3.40 running GANYMEDE + and I need to also run 802.1 x radius to meet DISA requirements, I've been working on it for a week. I am unable to get the characteristics of work, all AD connections are already there for GANYMEDE + and so I'm not sure how config, Ray can someone help with the procedures.

  Hello

  in the configuration of the aaa you must specify the two authentication 802. 1 x that points to the RADIUS and peripheral administration of Ganymede.

  Configuration of the network device ACS apply both radius and Ganymede keys.

  There will be no conflict for the same as the two have different sets of commands.

  Thank you

  Please rate if useful...

• Can I use an ACS as RADIUS and GANYMEDE to the same ASA Server?

  I want to GANYMEDE to make the accounting of the SAA, meanwhile, the ASA need RADIUS for authentication ssl vpn. Is it possible to reach this object with only a CSA?

  Yes, you can use both. Allows you to add ASA as radius and Ganymede.

  ACS-->---> aaa-client network configuration

  (1) ASA---> 1.1.1.1---> authentic using Ganymede

  (2) ASA1---> 1.1.1.1---> optout by radius

  Don't forget the host name cannot be the same.

  Kind regards

  ~ JG

  Note the useful messages

• ASA auth-proxy Radius and downloadable ACLs

  Hello

  I want to have ACLs that decide what traffic to allow after authorization auth-proxy.

  1. What are the options I have to ASA + ACS?

  2. can I use auth-proxy on SAA with the CSA and download RADIUS and ACLs?

  3. can I use auth-proxy on SAA with the ACS and Ray 01/09/00-cisco-av-pair (will be ASA understeand it?)

  4. can I use auth-proxy on ASA attrbuts auth-proxy ACS and Ganymede (with ACLs)?

  Thanx

  Hello

  Take a look at this guide to see if that helps answer your question. You can use the downloadable ACLs or the cisco av pair, I saw that the cisco-av-pair method works a little better because he has the user name who logged in as part of the acl which facilitates troubleshooting.

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/access_fwaaa.html#wp1150820

  Thank you

  Tarik Admani

• This is where other issues of quality and quality Plans are grown?

  This is where other issues of quality and quality Plans are grown?

  Ben

  As the quality is part of discrete manufacturing module that seems logical, but you might also find some useful discussion for the purchase or manufacturing process.

  JS.

• Known issue 9.2 and 9.2.1 Siri?

  Siri will not process my requests to set alarms and timers, add events to my calendar, schedule reminders (among others). It will make calls to my contacts, sometimes. I called Apple technical support. I have done sunsequently a Genius Bar last week Thursday, and genius appointment he ran through a bunch of tests, did the resets, etc. and told me she would call back at the beginning of the past week.

  Because I never heard of him, I stopped yesterday and met with another genius. He told me he had intermittent problems with Siri as well. I told him, I understand, but Siri has not worked for me for three weeks in this particular way (some applications to work while others are still not). The genius sent me this email shortly after:

  

  Everyone knows about this problem? Would just continue to wait and update in the hope to be able to use the feature (Siri) once again?

  Thank you.

  I have exactly the same problem with my iPhone 6.   I could not use Siri on my iphone to play music, send text Messages, etc. Since the middle of December 2015. Everything worked fine for a year and then suddenly one day it just stopped working.

  I contacted Apple Support and they told me that they had never heard of this issue before!   They ran a bunch of 'tests' with me by phone but could not resolve.  They said they'd call me back when they had a solution - I'm still waiting for a callback.

  It's frustrating because I've always used my iPhone with eyes for free in my car listening to music and I can do it no longer.  Siri is a feature that I bought my iPhone to use and it does not work.

  The 9.2.1 update was has not solved the problem.

  I'd like to hear if you get this solved.

• HP Pavilion x 360: back issues of sleep and stop; MEI driver moved

  I have upgraded to Windows 10 last summer and, like many people, I had sleep and close issues. The computer wouldn't wake him up after he went to sleep and when I stop the computer the light remained on and the fan will continue running. I was able to fix by updating the graphics card and the driver of MEI.

  Windows has released a new update a few days ago and it has been applied automatically to my computer. Now, sleep and shutdown questions have returned.  This time, the graphics card is fully updated, but now I can't downgrade my MEI driver back to version 8.1 of Windows ( 9.5.24.1790 1.5 M ). When I try to install the driver it says 'Setup progam was able to start one or more application processes' and stops. I tried running the installation through Setup of HP and download directly, and none worked.

  Does anyone else have this problem? Any advice?

  Open Device Manager, expand the 'System devices' section, and then find "Intel Management Engine interface", double click it and go to the driver tab, and then click on "roll back driver" button, it will come back to the previous driver.

  You can do most any device in the device manager driver.

  If roll back driver button is gray, then there is no older driver to restore.

• issue with tables and clusters

  Hello

  Another issue with the tables and clusters. I have three engines thatI move on XYZ and then measure something. I need to draw on the 3D, the result of the measurement. How to draw real XYZ and not the index of the data table positions? (I can't actully how to build the matrices 2D forX, Y and Z). In the figures, I give an example of what I need.

  Concerning

  You have to break the data out of the cluster and to present them to the graph 3d to a separate bays for X, Y, Z and W where 'W' is your values measured at the locations described by X, Y, Z.

  This thread shows how trace readings in space 3. The following image shows the data that the original author wanted to draw.

  

  Have fun

  Ben

• GPIB - issue VISA (LV2014 and Keysight IO libraries)

  Hello together!

  I have tried for two days to meet the LV2014 - Keysight IOLib - Agilent DSO6014L...
  And I need help.

  What I want to do

  I have a LabView VI for the osziloskop control and obtain values of. I created the VI with LV8.5.1 and it worked very well with Agilent Io Lib 14 and Windows XP. Unfortunately, I had to change to a new computer...

  And the problems started, I do not get the components together (at least, not without error messages in MAX):

  I connected an Agilent DSO6014L by a GPIB 82357 A Agilent to a Windows 7 Enterprise edition - 64-bit.

  I already posted my problem in German LabView Forum ( http://www.labviewforum.de/Thread-LV-2014-und-Keysight-IO-Libraries-Suite-17-1 )

  GerdW already replied and proposed to connect via LAN or switch to a NI GPIB.

  But maybe there's a way to solve my problem, keeping the "old" material.

  Currently, I can run my VI because I use aliasnames which I attributed to the IOLib and MAX (below I've listed the steps I did).

  But Max I still got the error "0xBFFF003A (VI_ERROR_INV_SETUP)" of viFindRsrc.

  -> More funny. If I say / activate the tulip Passport - save parameters - and restart MAX. I don't have any errors and I see my GPIB instruments... uuuuntil I refresh the view!

  Steps to make it work:

  • Installed Labview 2014 - not reboot!
  • Keysight IO libraries Suite installation (default) 17.0.19313.5, automatically as secondary VISA
  • Under Keysight connection compatible Expert maps GPIB for 488 program and set options of PXI (Resource Manager active and responsible trigger by default) of National Instruments
  • Connected the GPIB 82357 A Agilent and install the driver (windows driver update speed search to jump to the top)
  • Install the driver for the oscilloscope (in my case ag6000 for DSO6014L for LabView 2014 32) and 64-bit support
  • Restart
  • Turn on the oscilloscope
  • He searches the IOLib - here everything works fine no problem to control the oscilloscope
  • In turn MAX on NiVisaTulip.dll under passports (MAX restart, get the 0xBFFF003A error)
  • Restart

  Now, there are some steps that I could possibly do before restarting:

  • In Keysight IOLib I updated the GPIB ID 1 (VISA Interface ID and ID of Interface of CLCL) - there was a note that the Tulip Passport uses the GPIB0 and this causes connection issues
  • Max under VISA conflict Manager, I enabled Agilent VISA under implementations installed VISA
  • Max under general settings - Interfaces PXI/PCI - active option to display all devices accessible to the VISA
  • In MAX under passports disabled NiVi488.dll and NiViGpvx.dll

  Now it is running once, and I put the same alias under IOLib and MAX name for my oscilloscope.

  In addition:

  • Installed drivers IVI Keysight IOLib RPF
  • Reinstalled NIVISA1401Full with support 32 and 64 bit
  • Did all the updates of NOR

  Hello

  Thanks for your posts.

  Yes I also use Agilent GPIBs for other screws so I need a solution running.

  I found this post:
  Passport (GPIB) max

  "Agilent IO libraries Suite v 16.2.15823.0 ' works very well with all my gear in IOLib, MAX and LabView 2014.

  I also tried the ' Agilent IO libraries Suite v 16.3.17914.4 ', which also works perfectly with all.

  For my solution, I give a brief summary of my installation (GPIB Agilent GPIB 82357 A, Agilent DSO6014L):

  • Windows 7 Enterprise Edition SP1
  • LabView2014 SP1
  • MAX 14.5.0F0
  • Driver for LabView ag6000 (support 32 and 64 bit)
  • NIVISA1401Full (support 32 and 64 bit)
  • Agilent IO libraries Suite v 16.3.17914.4 (driver for Oscilloscopes 6XXX 1.3.24.0 IVI)

  and parameters:

  • Agilent IOLib - installed as secondary during custom installation VISA, I can not set the 488 (box all the time is reset), but it works fine without. And I did not change GPIB or ID of CLCL. I gave an alias to my instrument.
  • MAX - all passports are activated. I checked the show box any device accessible to VISA. I gave the same alias to my instrument, as in Agielnt IOLib. Under conflict Manager Agilent Simulation VISA is selected and Agilent VISA is disabled, all chosen VISAs are the Canadian standard.

  Best regards

  André

• Compatibility issues with gwbasic and SBS 2011.

  I currently have SBS 2003 and upgrade to SBS 2011 and a new 64-bit server.  I'm running a gwbasic program and want to know if there will be problems on my workstations.  I don't think I'll be able to run the program locally on the new server.  We had a few speed issues for most in multiuser situations.   The problem seemed to have much worse at a time I made a few changes at the same time.  Multiple e-mail accounts to Exchange, Setup of email accommodation, added a Windows 7 machine, past all the other workstations to XP Pro (4) and did my back based gwbasic program update software.

  Hello

  I suggest you send the question in the TechNet forums and check if it helps:

  http://social.technet.Microsoft.com/forums/en/smallbusinessserver/

  It will be useful.

• EVGA Nvidia Geforce 8400 GS issues: [FIXED] screen and the sound does not [FIXED] virgins

  I have a HP Compaq dc5750 I just got an EVGA Nvidia Geforce 8400 GS, and I'm having a problem with it. I disassembled the computer cover and installed, replace the cover, turned on the computer and the monitor not power not on. So I decided that I had to disable the integrated graphics card (ATI Radeon Xpress 1150), then I added the card even once. Still happens... Monitor powers on without the new graphics card. My monitor is 8 years old and lacks a DVI port. I have to connect the monitor to the graphics card to make it work? I want just this card to work.

  UPDATE: white screen problem is fixed, but the sound does not (no audio installed device) even if the audio driver is installed

  Hello

  This kind of question is mainly caused by the sound card driver is not not compatible.  Contact the hardware manufacturer directly to confirm the driver is compatible or not.

  Test the issue with another pair of speakers or headphones, or you can plug the device of reading to another port to see the result.

  In the meantime, you can also see if the playback device is disabled. To do this, please check the following steps:

  1 Please, click Start-> Control Panel-> Sound.

  2. on the playback tab, right-click on the empty square and then click on "show disabled devices".

  3. check if your playback device is disabled. If so, right-click on it and click Activate.

  1. Please click Start, type services.msc and press ENTER.

  2. double-click on Windows Audio.

  3. click on the 'general' tab. Make sure the "Startup Type" is "automatic". Then please click on "Stop" under "Status of Service" to stop the service.

  4. click on "Start" under "Status of Service" to start the service.

  Reinstall the audio device

  1. click on start, type Device Manager, click on Device Manager to open it.

  2. expand ' audio, video and game controllers ".

  3. right click on your audio device, and then click on uninstall.

  4. check "delete the driver for this device".

  5. click on OK.

  6. after that, restart the computer, the device and the driver must be reinstalled automatically.

  Please check if the problem can be solved now.

  If the problem persists, please install the latest driver of sound card on the manufacturer.

  I found the problem... once again: I had to go to the BIOS and enable Audio integrated. My audio integrated uses Realtek High Definition Audio instead of Nvidia High Definition Audio.

• icon comments with other issues of icon and download arrow on this subject, on the Security tab.

  I'm on a laptop computer with dsl internet IE with another computer using the gateway. My os is Vista Home premium and service pack 2. I checked my settings on a regular basis and updated and scanned my system regularly. I periodically check the security settings for all the problems, and they are usually very good. However, I had taken a couple of times in administrator mode, I don't have the rights of security to certain files or programs. When I checked the security labels, I got a message that I could see the settings, but could not make changes. This should not be, as far as I know, because the administrator must have all the rights. I've never seen any icon like this on the Security tab, (or anywhere else) in the past. I went into the security on a folder tab and proceeded to bring up the list of groups and their safety features and found the icon comments soiled by a arrow pointing down. Guests (multiple) icon didn't. I can't bring up anything on this subject. I'm the only person on this computer, and I use the only admin account to do administrative tasks.  I have a personal account, which is a standard user account and both accounts are protected by Word. The guest account has never been activated. The curious to keep in mind another note is that other groups are listed under the name of my pc, but system and comments are not included, for a long time with others who are in the usual list of people or groups. I'm sure that the system must be included, because that always has all the rights. I don't have not find a way to change the icon, or find info for the customer. I searched your site and forums, as well as several other pc and tech support forums and can't find anything close to this issue, save the information on the Chameleon that MSN uses in their toolbar that makes icons from almost anything. Who is listed in my registry under MSN. It seems trivial, but I think it is maybe not so innocent, if it's way in. There are icons from two people on my printer files even if I checked them as not shared. I had checked to share, as well as the share folder normal, to see if anyone is on the network of the group to my computer profile. There was no evidence, however, I thought it would show the other computer on the local network, since the group is the same name. These icons came from. Everyone was listed as entitled to print and edit or delete parameters or printers and print on stations there. I couldn't do that. At most I would not have understood change or delete anything. In the group list, everyone was marked not with my pc name. Local service, I thought I was usually part of the active list is not marked either. System is not marked either. Here is a list of what it says:

  Administrator, administrators, ASPNET user to the debugger, distributed COM users, readers of the event log, the (acc't of the admin), comments, invited, IIS_IUSRS, IIS_WPG, Performance Log users, users of performance, (me), monitor users.

  I'm a little puzzled. Y at - it a simple explanation that I may have missed?

  In Vista, administrators have all the access rights as they did in XP.  NUMBER of cases do not have access.  There are records of point junction where everybody is seen to deny access.  This is intentional to decrease the chance that someone will change, move or delete something, they should not (even administrators).  Some of them can be modified in order to access and others require special modifications of access - which shouldn't be done without a VERY good reason (as told to do so by Microsoft Support).  What you missed is that the permissions have changed in Vista from XP.

  Here is some information on permisions and property in Vista that can help:

  To view your permissions, right-click on the file/folder, click Properties, and check the Security tab.  Check the permissions you have by clicking on your user name (or group of users).  Here are the types of permissions, you may have: http://windows.microsoft.com/en-US/windows-vista/What-are-permissions.  You must be an administrator or owner to change the permissions (and sometimes, being an administrator or even an owner is not sufficient - there are ways to block access (even if a smart administrator knows these ways and can move them - but usually should not because they did not have access, usually for a very good reason).)  Here's how to change the permissions of folder under Vista: http://www.online-tech-tips.com/windows-vista/set-file-folder-permissions-vista/.  To add take and the issuance of right of permissions and ownership in the right click menu (which will make it faster to get once it is configured), see the following article: http://www.mydigitallife.info/2009/05/21/take-and-grant-full-control-permissions-and-ownership-in-windows-7-or-vista-right-click-menu/.

  To resolve this problem with folders, appropriating the files or the drive (as an administrator) and give you all the rights.  Right-click on the folder/drive, click Properties, click the Security tab and click on advanced and then click the owner tab.  Click on edit, and then click the name of the person you want to give to the property (you may need to add if it is not there--or maybe yourself). If you want that it applies to subfolders and files in this folder/drive, then check the box to replace the owner of subcontainers and objects, and click OK.  Back and now there is a new owner for files and folders/player who can change the required permissions.  Here is more information on the ownership of a file or a folder: http://www.vistax64.com/tutorials/67717-take-ownership-file.html.  To add take ownership in the menu of the right click (which will make it faster to get once it is configured), see the following article: http://www.howtogeek.com/howto/windows-vista/add-take-ownership-to-explorer-right-click-menu-in-vista/.

  A lot of general system groups are included by inheritance rather than be listed in each file and folder - that's why they are not always there - but they are.  If you select Advanced, you'll see permissions inherited from other folders.

  I have no idea on the arrow on the guest account - I don't know what that means.  It may have something to do with safety or you installed AV programs (I know that Norton did something similar with the files to show if they have been backed up).  Personally I don't use the guest accounts and recommend against them because they are too easy to use to hack the sytem (and other reasons).  I would keep the disabled guest account and delete the duplicates but one off a (in the start menu / control panel / user accounts / manage other users).

  I don't know why you can't see other computers on your local network - that sounds like a network or installation problem connection coming to redo the connection from scratch will fix (and then you can remove the one that isn't working right).  I don't know why your printer changed - rights but you can easily set them back to how they must be with the Security tab in the properties of the printer (and other settings in the start menu / control panel / printers).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• WAAS for RADIUS and Windows Server 2012 NPS server configuration

  I have trouble getting our WAAS to authenticate devices and connection via RADIUS.  Running NPS on Windows Server 2012.  Confirmed that my device WAAS can ping the IP address of the RADIUS server.  Using the attribute Type of administrative service under network policies.  Look in the event viewer, I get an error with event ID 15, "a malformed RADIUS message has been received of the xxxx-WAAS-01 customer. The data is the RADIUS message. »

  Right now, I can connect with only the local default user and password name.  Here are a few config for WAAS, running version 6.2.1:

  RADIUS server key *.
  Server RADIUS auth-host 10.194.10.13 port 1645
  !
  connection of local authentication enable secondary
  enable login authentication RADIUS primary
  local authentication configuration enable secondary
  Service radius Authentication configuration Select primary
  failover of authentication server unavailable

  I confirmed that my shared key is entered correctly on the WAAS and the NPS.  I have the switches/routers Cisco works well on the same RADIUS server.

  Someone had a bit of luck plug their WAAS to RADIUS devices using Windows Server 2012 and NPS?  If so, please share additional measures you have taken to get things to work.

  Hi Paul,.

  Based on the RADIUS error you probably experience failure CSCva14731. This was discovered with Cisco ACS, but can affect other RADIUS servers.

  To confirm, you can check the corresponding error in syslog WAAS:

  authenticate: % WAAS-UNKNOWN-3-899999: pam_radius_auth: talk_radius: RADIUS server did not respond (timeout 5 (sec))

  Also, this defect would not affect peripheral on software 5.x WAAS.

  The problem will be solved in 6.2.3 to come free.

• 802. 1 x authentication with Radius and win7 Mab

  Good afternoon!

  I have a question about 802.1 x I've set up a laboratory in which I have configured authentication mab with 802. 1 x, but I have a weird behavior of my network controller. On the switch (4948e), I see that the user is authenticated and authorized, and I can see my switch these outputs:

  21 April 15:13:30.263: % AUTHMGR-5-START: start "mab" for the customer (a01d.48ac.b7f
  (5) on the Interface item in gi1/11 AuditSessionID C0A8DF9C0000002E002F3DAC
  * Apr 21 15:13:30.267: % MAB-5-SUCCESS: authentication successful for the client (a01d
  . 48AC.B7F5) on the Interface item in gi1/11 AuditSessionID C0A8DF9C0000002E002F3DAC
  * April 21 15:13:30.267: % AUTHMGR-7-RESULT: authentication result 'success' of me
  ab' for the client (a01d.48ac.b7f5) on the Interface item in gi1/11 AuditSessionID C0A8DF9C00000
  02E002F3DAC
  * Apr 21 15:13:31.299: % AUTHMGR-5-SUCCESS: authorization succeeds in for the customer (a0
  1d.48AC.B7F5) on the Interface item in gi1/11 AuditSessionID C0A8DF9C0000002E002F3DAC

  If I type "see the authentication session", the corresponding output.

  Switch #show authentication sessions

  Interface MAC address method ID of Session of field status
  Item in gi1/11 a01d.48ac.b7f5 mab DATA Authz success C0A8DF9C0000002E002F3DAC

  The thing is that when I check my network controller, it said "authentication failure". That's what I've done so far:

  1. I restarted my pc, the same behavior.

  2. I disabled and enabled my network controller, the same behavior.

  3. I rebooted the switch and re-configured. Same behavior.

  4. I tried with another PC configuration. Same behavior.

  5. I changed the configuration of "user authentication" using dot1x EAP authenticator and it worked.

  This is the configuration I have on my switch:

  AAA new-model
  Group AAA dot1x default authentication RADIUS
  Group AAA authorization network default RADIUS
  start-stop radius group AAA accounting dot1x default
  AAA - the id of the joint session

  !

  control-dot1x system-auth

  !

  Switch #show run gigabitEthernet int 1/11
  Building configuration...

  Current configuration: 128 bytes
  !
  interface GigabitEthernet1/11

  Cx-to-Host description
  switchport access vlan 223
  switchport mode access
  Auto control of the port of authentication
  MAB
  end

  This is the first time I'll put up a configuration 802. 1 x. I'm doing something wrong?

  I really hope that I am not the only one with this kind of behavior!

  Thank you for any assistance you can give me!

  Status: Authz success

  This means that the port is open. Is this permanent? Keep looking at the output of the show a few minutes see if it tries to dot1x too. Can you ping from the PC?

  As authentication of 802. 1 X is enabled in the properties of the map NETWORK PC that you can expect dot1x method runs on the switch and eventually respond to the computer with auth fail. Authentication in the PC box is not necessary for MAB.

  What type of RADIUS server you use and there 802.1 policy X in addition to MAB policy?

  IP address: unknown

  This means that the switch did not recognize the IP address of the host, probably due to the lack of

  analysis of IP device

  command. But it is not necessary for the plain MAB or dot1x.

• MS RADIUS and Cisco VPN client

  We currently have with a Server Windows RAS and IAS authentication with PPTP to users.

  I want to move a hub (we have two not used) and the use of the Cisco VPN client with IPSEC 3005, also using the RADIUS (IAS) in Windows to authenticate against Active Directory.

  I have a config to work for the client and it performs authentication, but I'm afraid that you can't configure IAS to work with IPSEC, unless you configure the policy for

  "Unencrypted authentication (PAP, SPAP).

  on the Authentication tab

  and

  "No encryption".

  on the encryption tab.

  Are encrypted with IPSEC credentials to establish the tunnel of the Cisco VPN client?

  For RADIUS PAP authentication, the user name is clear and the password is encrypted with the RADIUS shared secret.

  To maximize security, you would use GANYMEDE + or IPSec transport mode and isolated VLAN. But for most of us, strong passwords and physical security prevents the RADIUS PAP to a significant weakness.