LabVIEW 2011 SP1

Similar Questions

• Ask for a link for Labview 2011 SP1

  I ask for the link to download the Labview 2011 SP1.

  I have a bug that corrects SP1 (damaged Panel before, cannot open vi, see the discussion http://forums.ni.com/t5/LabVIEW/LabVIEW-load-error-code-3-Could-not-load-front-panel/td-p/1895379/pa...), but the download link disappeared.

  Please, if anyone knows tell me the link to download (32 bit).

  I found it here

  http://download.NI.com/support/softlib/LabVIEW/labview_development_system/2011%20SP1/

  Anyway, there are a few problems with the link that you gave to me. I thank you all the same because what is happening is somethink wronk with national instruments site, which is not the same for all countries (web designers should check and fix the bug).

• Problem installing module time real LabVIEW 2011 SP1

  Hi, I'm new here. I have a problem when I tried to install LabVIEW Real - Time 2011 SP1. Whenever the part of initialization, this message appears: "NEITHER Labview 2011 SP1 32-nit must be installed before installing the OR labview 2011 SP1 real-time Module.» I'm sure that I've already installed Labview 2011 32-bit SP1 and it works well. I use a Windows7 OS and also have Labview 2010 and an older version of Labview 2010 RT module installed. I didn't remove the old version of the software, and I don't know if it is related to this problem.

  Can anyone help? Thank you in advance!

  MrSun87 wrote:

  ... I'm sure that I've already installed Labview 2011 32-bit SP1 and it works well...

  Can post you a screenshot of MAX where are installed Versions of LabVIEW?

  Christian

• NOR-845 x driver Labview 2011 SP1

  Hi all

  I faced problem,

  I have a LabView program that is used to communicate with devices SPI-NOR-8451. Program worked perfectly, on PC with LabView 2010. After that, I moved the program to new PC where f1 LabView 2011 SP1 has been installed. And now, I am not able even open - LabView program stuck on the white block diagram (not responding).

  Program is complex and includes 10 ~ SubVis, which is packaged in the .llb file. I tried different things - to decompress from .llb, or run subVis themselves - for all the subVis, which include a part any communication NOR-8451, I've got stuck LabView. In addition, after the removal of NOR-845 x pilot, I can't ignore everything and load the program successfully, with '? ' instead of screws of NOR-845 x pallete.

  In addition, when I'am tring from white VI and set NEITHER-845 x ref Device link (see attachment for details Link_on_ref_.jpg) on the block diagram, I'm LabView stuck - see the attached Stuck_.jpg.

  I use NEITHER-845 x driver 2.0, I tried to reinstall several times.

  So, it's my suspicious that NEITHER-845 x driver 2.0 does not work for LabView f1 2011 SP1 - is it possible? Or maybe I'm doing something wrong?

  Hi RangerOne,

  Thanks for the trace, as LabVIEW is suspended, it is what I expected but hoped a different error code. If you could go to MAX and reset Configuration data, and then create a MAX Technical report and attach it.

  If you open the test Panel, you run a query, it works or hang? Try to run a trace when you try to query.

  I see the same error with the camera on my machine under interrupt in Pipe status is not abnormal.

  I also noticed that your computer input for findlist, retcount and SrcName parameters have not the & on the non-working paper. I will continue to examine the reason why the & is not there and if it has an effect on the shot.

  DylanC

• Just LabVIEW 2012. Why am I being asked to download LabVIEW 2011 SP1 f2 RTE Patch?

  Hello

  Recently, I got a new machine (clean install of Windows 8) and installed LabVIEW 2012, with no other previous versions. However, when I ran the Service OR day, he registered "LabVIEW 2011 SP1 f2 R(32-bit) Run-Time Engine Patch" as an update is critical.

  I'm confused; I accidentally installed LV 2011 too?

  Thank you

  No, you did nothing wrong.  time engine run freely installed with LabVIEW 2012 to record for previous versions.  Install the patch.

• LabVIEW 2011 SP1 makes such a big difference?

  Here's my work construction specification in LabVIEW 2011

  

  Any idea?

  First of all I spend time to upgrade to 2011SP and after the update, when I learn about broken build specification. I started to wonder is it really worth spending time to upgrade?

  BTW, the problem is resolved. How I have no idea. For the first 2 times, I opened the project, the build specification has been broken and the third time that I was correct. Fortunately I did not spare the first project 2 times.

• Need link to download LabVIEW 2011 Windows 32-bit SP1

  I looked up the link to download LabVIEW 2011 SP1 32-bit Windows for an hour.  I thought it might be incorporated in the version SP1f2.  Nope. SP1f1 version. Nope.  Research of ni.com do not, Google does not find it, I'm stuck.

  How about this?

  LabVIEW 2011 SP1 (32-bit)

• Executable VI with Labview 2011

  Hello everyone, I'm doing an executable on LabVIEW 2011 SP1. I've never done before, but in my project, I go to tools-> Build Application (EXE) from VI... I check to make sure that all the Sub VI are in the Dependencies tab and I put the way I want the EXE to go, then I build it. Building compiles and I have good Run-Time Engine installed, but when I go to open the EXE file, I get a lot of mistakes because void VI could not be loaded. I checked these Sub VI that were not loaded and they are locked and password protected. Probably comes with LabVIEW, so they don't want to play us with anything. How can I get these included in the EXE and not return an error?

  Thank you.

  I deleted the Run-Time Engine and downloaded again, and I think it worked. Strange, but I accept it

• Deal with failure when using LabVIEW 2011 and DSC MODBUS communication

  I'm currently reading from operating records a PLC with MODBUS/TCP. I confirmed that the PLC will update the values and in response to a MODBUS communication correctly by using a third-party program called Modbus Poll. However, when I try to query the PLC using the LabVIEW shared variable engine, I am unable to read the values of the same addresses that I consult with Modbus Poll.

  My installation is simply to a PC directly connected to the controller via Ethernet without a router between the two. I'm using LabVIEW 2011 SP1 with the DSC module.

  I opened the Manager of distributed systems OR to display the State of all variables in the Modbus Library that I created, and I noticed that the ILO CommFail permanently the value 'true '. All other variables with a 'read' access mode signal "failure of process". I tried to restart the process and stop and start the local variable engine without success. I also restarted my computer several times to see if any services did not exist, but this does not appear to have solved the problem.

  Finally, I resorted to listening to communications on the network card I have the PLC connected via Ethernet using Wireshark and found that while Modbus Poll communicates with PLC, number of MODBUS and TCP packet is sent and received. However, when using only LabVIEW or the DSM OR communicate with the controller, there don't seem to be any communication on the network card.

  Something that may be interesting to note is that I could communicate with the PLC and to read values with the DSM just once, when I understood everything first what address I should be reading of. All of this has stopped working shortly after. Prior to this, 'CommFail' was not generally set to 'true' with my current setup. Thinking it was my firewall, I have since disabled my firewall, but this seems to have had no effect on the problem either.

  Any help on this would be appreciated.

  So, I thought about it. It turns out that the IP address of the server i/o MODBUS must be set to the address of the MODBUS slave, not the local computer. The address of the i/o MODBUS server is defined by the navigation in the Explorer window projects, expanding the variable engine shared library for MODBUS and right click on the server MODBUS (for example Modbus1) item and select Properties.

  In addition, the addresses seem to be shifted by + 1.

  Thanks for the tip so.

• LabVIEW 2011 executable does not close

  Hello

  I created a very simple piece of demo code to try to discover Labviews Plugin architecture (please see attached).

  For some reason when I create my demo code in an executable file and click the button stop the façade that closes, but the program continues to run in the taskbar.

  I built, run and compiled my code in Labview 2011 SP1.

  My final actions for the main vi are to close the front panel and then call the function "Quit Labview".

  Failure to close occurs intermittently (it will close with success after 3 out of 4).

  I have attached my code.  Does anyone have an idea why it doesn't work?

  Thank you!

  
  

• OR Developer Suite 2012 DS1 disks to install only 2011 SP1

  My OS is Win7U64b. When I first installed LabVIEW (32 bit) of these disks 2012 DS1 has been installed. I did a complete uninstall and then reinstall of LabVIEW (32 bit). After the reinstallation, only LabVIEW 2011 SP1 was installed and 2012 DS1 was not. Why? How can I return LabVIEW 2012 DS1?

  The version of LabVIEW is not directly related to the Developer Suite version.  Developer Suite 2012 DS1 has LabVIEW 2011 SP1.  Developer Suite 2012 DS2 will LabVIEW 2012.  Developer Suite 2013 DS1 has LabVIEW 2012 SP1.  See the model?  This is because the version of LabVIEW is in the month of August with the week, and service pack comes out the winter timetable / next spring.

  It is a constant complaint that neither was heard from 2010 when LabVIEW 2009 SP1 was released with Developer Suite 2010 DS1.

• Impossible to download LabVIEW OR SoftMotion Module 2011 SP1

  LabVIEW OR SoftMotion Module 2011 SP1

  http://Joule.NI.com/nidu/CDs/view/p/ID/2776/lang/en/rating/1

  Any link on this page you can download a downloader, and the Downloader can only download it self.

  Hello

  I don't know what is happening. For now, please download the Module OR SoftMotion from the following link: https://lumen.ni.com/nicif/us/EVALTLKTINDCTRL/content.xhtml

  I checked that it works.

  Thank you

• Wiring of connectors in LabVIEW 2011 problems

  I've just been 'bitten again"by a wiring problem with a connector for a VI in LabVIEW 2011 (I've not seen this behavior in any previous version of LabVIEW to 7.0).

  The question is this.  I (or one of my colleagues, who also noted it), run LabVIEW 2011 (August 2011 release), 32 - bit, Windows 7, 64-bit systems.  I have create a VI using the usual 4-2-2-4 connector of mires and connect the appropriate connector.  I save the VI, then drop it on a block diagram to use.

  In another variation of this problem, the VI has fallen don't watch any connector or, if used to 'replace' an existing wired in VI with the same model of connector, "break" all the sons (because it has no connector when dropped on the diagram).  Reopen and reconsider the VI show that, indeed, the connectors are wired, but when I use the VI, the connector wiring is absent (the VI dropped watch without connectors).

  In the second variant, all right, the connectors appear as expected.  But I then decide to move a connector.  I have open the VI to edit, make a cut of this Terminal and rewire to its new location.  The connector pane presents the new model.  But when I drop the VI on a block diagram, the connector is in its original location.

  Restart LabVIEW, indeed restart the PC, does not change.  The only way to 'fix' this is to disconnect all terminals and a reconnect them.  A nuisance, to say the least, but also an obvious bug.

  Has anyone else seen elsewhere?  I sent to OR, but it would be useful to know 'is it just me?' or not.  In my defense, I've seen this problem on several computers, all win 7/LabVIEW 2011.  I've also seen this with several LabVIEW projects.

  I've attached a file with such a VI "buggy".  When you open it, you will see that the 'Length' indicator is wired to the top of the connector set page.  When I drop this VI on a new VI, however, the connector indicates coming out from the bottom!

  BS

  I was told by an engineer NOR that this problem (a) is real and (b) has been fixed in SP1 release (spring) 2011 LabVIEW.  I have not had a chance to check this point, but (the trusting soul that I am), I consider that this problem has been a "Bug in LabVIEW 2011 that has been fixed in the SP1 Release"and therefore, I am prepared to mark this "resolved".

• How to run the VI developed in labVIEW 2011 in its previous versions

  Hi all

  I am currently using LabVIEW 2011 in my PC at home.

  But, all my school's computers are installed with LabVIEW 2010 and 2010 SP1.

  How to run the VI developed in LabVIEW 2011 in its previous versions?

  Is there any conveter why?

  Concerning

  Prasanth T

  Open the VI in LabVIEW 2011 and use the file menu option, save for the previous Version.

• [Bug]? LabVIEW 2010 SP1 - Device Drivers Incorrect link

  Hello

  This page link to download LabVIEW 2010 SP1 Device Drivers Feb 2011 on this page points actually to November 2010.

  

  See you soon

  -JG