Problem installing module time real LabVIEW 2011 SP1

Similar Questions

• using the module time real Labview in RTAI

  Hi all

  I want to use the module time Labview in RTAI real for real time due to its open source applications and very good performance. is it possible to make this work?

  If this is the case, can anyone introduce a single study of case or something similar to this?

  Cecile says:

  Hi all

  I want to use the module time Labview in RTAI real for real time due to its open source applications and very good performance. is it possible to make this work?

  If this is the case, can anyone introduce a single study of case or something similar to this?

  I don't think it's possible for anyone outside of OR. LabVIEW Real-time supports this time only Windows as host and as a target only material of National Instruments with specifically targeted OSes or the Pharlap ETS system on x 86 systems with hardware specific enough. Using RTAI as target OS for LabVIEW Real-time applications requires first a few changes on the time plugin real LabVIEW to support this new platform.

  None of the files in time real LabVIEW also created for either platforms OR running VxWorks or OS Pharlap, Pharlap ETS system woud be able to be deployed to a system RTAI, because they are not compatible. In the first place, you'd have to port the bunch of shared libraries that make up the time target real system running LabVIEW on one of these goals to your RTAI system which is in fact a whole new platform of LabVIEW you can create with a little effort from the LabVIEW source code. It's not really impossible for OR as most of the code LabVIEW is written platform completely independently, but it would be a combination of the parameters compilation for course LabVIEW Real-time, with the settings to produce time targets real LabVIEW VxWorks with some additional settings of Linux. Yet, it would be by far not trivial and some parts are actually hardware specific drivers that must be worn too and limit the possibilities of what RTAI material could serve even further. In short not something that would make any commercial sense NC because they invest a lot of resources with no opportunity to sell additional hardware.

  And hell freezes over up front release of NI LabVIEW source code in any form which gives access not - OR used to it!

• NOR-845 x driver Labview 2011 SP1

  Hi all

  I faced problem,

  I have a LabView program that is used to communicate with devices SPI-NOR-8451. Program worked perfectly, on PC with LabView 2010. After that, I moved the program to new PC where f1 LabView 2011 SP1 has been installed. And now, I am not able even open - LabView program stuck on the white block diagram (not responding).

  Program is complex and includes 10 ~ SubVis, which is packaged in the .llb file. I tried different things - to decompress from .llb, or run subVis themselves - for all the subVis, which include a part any communication NOR-8451, I've got stuck LabView. In addition, after the removal of NOR-845 x pilot, I can't ignore everything and load the program successfully, with '? ' instead of screws of NOR-845 x pallete.

  In addition, when I'am tring from white VI and set NEITHER-845 x ref Device link (see attachment for details Link_on_ref_.jpg) on the block diagram, I'm LabView stuck - see the attached Stuck_.jpg.

  I use NEITHER-845 x driver 2.0, I tried to reinstall several times.

  So, it's my suspicious that NEITHER-845 x driver 2.0 does not work for LabView f1 2011 SP1 - is it possible? Or maybe I'm doing something wrong?

  Hi RangerOne,

  Thanks for the trace, as LabVIEW is suspended, it is what I expected but hoped a different error code. If you could go to MAX and reset Configuration data, and then create a MAX Technical report and attach it.

  If you open the test Panel, you run a query, it works or hang? Try to run a trace when you try to query.

  I see the same error with the camera on my machine under interrupt in Pipe status is not abnormal.

  I also noticed that your computer input for findlist, retcount and SrcName parameters have not the & on the non-working paper. I will continue to examine the reason why the & is not there and if it has an effect on the shot.

  DylanC

• Just LabVIEW 2012. Why am I being asked to download LabVIEW 2011 SP1 f2 RTE Patch?

  Hello

  Recently, I got a new machine (clean install of Windows 8) and installed LabVIEW 2012, with no other previous versions. However, when I ran the Service OR day, he registered "LabVIEW 2011 SP1 f2 R(32-bit) Run-Time Engine Patch" as an update is critical.

  I'm confused; I accidentally installed LV 2011 too?

  Thank you

  No, you did nothing wrong.  time engine run freely installed with LabVIEW 2012 to record for previous versions.  Install the patch.

• Ask for a link for Labview 2011 SP1

  I ask for the link to download the Labview 2011 SP1.

  I have a bug that corrects SP1 (damaged Panel before, cannot open vi, see the discussion http://forums.ni.com/t5/LabVIEW/LabVIEW-load-error-code-3-Could-not-load-front-panel/td-p/1895379/pa...), but the download link disappeared.

  Please, if anyone knows tell me the link to download (32 bit).

  I found it here

  http://download.NI.com/support/softlib/LabVIEW/labview_development_system/2011%20SP1/

  Anyway, there are a few problems with the link that you gave to me. I thank you all the same because what is happening is somethink wronk with national instruments site, which is not the same for all countries (web designers should check and fix the bug).

• LabVIEW 2011 SP1 makes such a big difference?

  Here's my work construction specification in LabVIEW 2011

  

  Any idea?

  First of all I spend time to upgrade to 2011SP and after the update, when I learn about broken build specification. I started to wonder is it really worth spending time to upgrade?

  BTW, the problem is resolved. How I have no idea. For the first 2 times, I opened the project, the build specification has been broken and the third time that I was correct. Fortunately I did not spare the first project 2 times.

• LabVIEW 2011 SP1

  I was wondering if anyone knows if\when Labview 2011 the service pack will be available?  Have just got the CD for 2011 of it Department, but realizing that they often release a service pack in February in order to don't want to lose a day to install the original on machines only to withdraw again.

  Service Packs generally download released, but NEITHER pre-announce them. Installation of LV2011 before the Service Pack is not a big deal, certainly useless "uninstall anything" before the Service Pack on your computer. If you include addons or tool boxes, these are usually not updated in the service pack there are a number of good reasons to go ahead and put 2011 on your computer now.

• I can't MJD (date and time) in LabVIEW 2012 SP1?

  I need some time my data of stamps before sending it to the file.  I did this with the standard calendar date and time but MJD is that we prefer to use.  How can I get a timestamp MJD in LabVIEW 2012 SP1?

  Check the JD MJD conversion formula
  http://www.IERS.org/nn_10828/IERS/en/service/glossary/MJD.html

  The modified Julian day (MJD) is defined as MJD = JD - 2400000.5, where JD is the Julian Day

• Problem installing Bootcamp on MBP late 2011

  Hello

  I have a model of Macbook Pro late 2011 and I wanted to install Windows 8.1. I downloaded the ISO file and installed the file on a flash drive and downloaded the drivers from Microsoft support as well. Boot camp successfully installed the ISO and the files on the flash drive and partitioned my disk and initialized in the flash drive (with success), entered my activation code. However, when it came time to choose my boot camp partition, it repeatedly gives me the error "Windows cannot be installed to this disk. The selected disk is a MBR partition table. On EFI systems, Windows can only be installed on GPT disks. "I also received error messages about it needing to be in format NTFS, but I fixed this problem. I followed other tutorials and guides for the problems of which has involved the partition exFAT and reformatting of the flash player install to put in shape, but it gave me no result. The reason why I chose to burn a key USB and not a DVD is because my computers internal DVD drive seems to be broken. I hope that the hotfix that is required to install windows does not require me replace the internal SuperDrive. Help, please.

  Installation of boot EFI (non - MBR) on a Mac 2011 is problematic and many driver issues ensue. You can delete the MBR using GPT Fdisk, but boot EFI, which is allowed on the GPT disk, will cause more pain later.

• How to create a graph in time real LabVIEW 6.1?

  I am new to programming in LabVIEW (6.1). I wonder to create a LabVIEW interface that can operate the multimeter Keithley 6487, allowing us to apply a voltage and nth measures. With the measures that we have create a chart (V curve i) I find the XY graph, but it only allows to send all the measures at the same time (indexing) to generate the graph and not whenever we take the action so the graph build inn in real-time. I need to know how to create a chart or change the XY graph, so I can generate the i - V curve with each step we take in real time. Whenever we take the action and not once the program ends. Thanks in advance.

  You must place the graphic inside the loop and the use of shift registers to accumulate the X and Y in the form of tables. I do not have 6.1 right now in the process of execution, but it would basically look like this:

  

  Note that the above is for demonstration (the code is in fact a greedy loop). You can consider putting Scripture on file inside the loop. In this way, if the program crashes, you will not lose your data.

  WARNING: Using table build as indicated above will result in continued growth of memory. If your program is running for a long time, this can become a problem. One thing you may need to watch must have a limit on the size of the array. I know there is an example of "Table of XY" comes with LabVIEW, and I'm sure that this is with 6.1. You should take a look at this example, which implements a fixed buffer for the data in the chart size. You should be able to use the VI "graphic buffer XY"directly in your code. "

• Behavior in time real LabVIEW incompatible with nodes in control property

  LabVIEW 2014 no service don't pack

  cRIO 9068 (Linux) with dual CPU

  I've written a vi which interacts with the CVT to pass values between the CVT and a bunch of controls on the Panel before which are accessed by reference. My project supports a front panel, if it is connected, then you can use this Panel to interact with the system. All the controls are located in a tabbed pane on the main vi running on the RT module, all the features are contained in a subvi, which accepts an array of references to the command input.

  It works perfectly in developer mode. Then when I deployed the controls were completely isolated: nothing has been loaded and initialized from the CVT, changing values of control had no impact on the system.

  For debugging, I provided a string array of all labels of control so I could see what controls is taken up by the Group of experts. So, I thought that the first troubleshooting step would be to see if the autonomous execution of RT filled one of them. After the creation and execution of this, everything lights up and works perfectly.

  It seems that to allow some control connected to that communication of the façade with a sub - vi RT VI must appear on the front panel. If this is not the case, the sub - vi will not interact with controls at all.

  In my opinion, it's a bug. Comments or details, anyone?

  Thanks for all your replies. For the record, while the 9068 has no Panel incorporated, it supports remote facades. I use this function successfully. The core of the code runs without a head, I didn't want the hassle of establishing a completely independent group on an external PC.

  My initial analysis and statement of the problem was wrong. I thought I was running in RT with group work, but actually worked by the developer. Even with controls and indicators highlighted the sub - vi the Panel was still Catatonic.

  Then I re-read the documentation OR on the facades. They clearly affirm that if application of the RT IS CONNECTED to a front panel nodes of property etc. will work. If this isn't the case, the program will still run but indicate errors for operations of property node. General error handling is not made for information only Panel stuff, so I have not seen the error.

  It turns out that I've been collecting all the controls at the beginning. Developing mode of the front panel is still there, so it worked. However, when the RT target boots and starts, it is impossible to have a remote façade connected, so my set of controls was empty.

  Movement of the control the value code initialization (just to get an array of references to all the controls in the component of interest) in the area of code that is run after the mouse click that activates the Panel did the trick. If there is no remote Panel then person can click on it, but if there is a front panel then all the controls are there.

  Thanks again for ruminating with me.

  Bill

• Acquisition of data in time real LabView

  I'm trying to get a better idea of what is happening when I'm DAQ using LabView RT compared to using the DAQ assistant (which cannot be used in LVRT).  In the DAQ assistant I could just say to acquire 300 samples at a rate of 3000 s/s.  The buffer waiting for 300 samples to fill, I could then take these samples and average in statistics to get a nice clean data every 100 ms.  I can't find out how to do something similar in LVRT.

  I am currently using a loop of data collection separate from my time critical loop operating at 100 ms.  I didn't tell him how many samples to catch so I guess he catches just real-time data point every 100 ms.  A number of data (pressure, temperature, flow, etc.) is written in a cluster that is sent to a network shared variable (which is sent to the loop of the host).  If I run the loop of the host to 1000 ms (where I save the data in a spreadsheet) just grabbing the 10th point data that the shared variable of the network trying to send to the host?  Is - this there anyway use LVRT in a similar way to the DAQ assistant, so that I can get the data more smooth.

  Oops - do not know what has happened to the code snippet (perhaps it was too big?) that I posted.  I will attach the VI himself here...

  BS

• Problem installing Modules common Satellite A20-S103

  I tried to reinstall the toshiba common modules for the error Thotkey. However, it does allow me to do. The following message appears: subsystem sous-fenêtres 16-bit c:\windows\system32\autoexec.nt. the file system does not fit the running ms - dos and microsoft windows applications. Click on close to terminate the application.

  I also tried to install it in safe mode, but it does not work either.

  Any suggestions?
  Thank you

  Hello
  tried to uninstall the common modules first?

  Good bye

• How to understand the context of the sequence of time real labview

  Does anyone know how Labview RT to understand the context of teststand sequence? My sequence context is defined as "TS. SequenceContext' like the screenshot in attachment.

  If we point a VI for that sequence context then who use VI of teststand? and must add this VI to the Explorer of Projectr of Labview RT system to build the project?

  I use 2009 Labview and teststand 4.2.1.

  Thank you very much

  LabVIEW RT does not support the ActiveX required for TestStand.

• Configuration required to use deskot as a target time real labview