Laptop does not go beyond the the BIOS splash screen

Similar Questions

• HP Pavillion DV5-1234SE does not start after the HP splash screen

  I have a HP Pavilion DV5-1234SE, which will not load Windows.

  It worked very well, I have stop him - and when I tried to start the next time, be put in place - but will only pass the first black screen with the HP logo. I'm trying to access the start menu, and tried to start in safe mode - but it will not go beyond the black HP screen.

  Any suggestions?

  Thanks for the suggestion. I ended up taking to someone and it turns out that the motherboard is fried. (Greaaat!)

  Rather than waste $350,00 replacing I'm just going to get a new laptop (not HP).

• My computer does not load past the Bios Dell screen

  Vista 32 bit Home Premium on Vostro 200
  Hey, my name is Christian and this is my problem:

  It all started last night when I (stupidly) decided I should change my screen windows open, you know, black screen, where the green bar would float through from left to right while the computer responsible. I decided to change to a sort of landscape of Lake, but this is not the point.
  Before that, I chose at the next restart, the registry would be defragged and there would be controls memory.
  I am so down and restart the computer.
  Computer turns on and I the landscape to the instead, loading screen unless it's just a picture, so there is not move bar telling me whether or not the computer was loading.
  And the screen just wouldn't change. I assumed that defragments the registry and memory check took place, but I was rather paranoid about whether or not something is going on I turned manually the computer off hold the button down.
  I turned it back again and he went to the same - screen landscape and would not pass as usual. Paranoia took ahold of me and I turned it off once again. I did it a couple of times (and I apologize) until a system repair came automatically.
  I thought it was my way out of this problem, but it didn't really fix anything, and the screen landscape had changed now in a black screen which seems to have a background image screen to vista aurora discoloration in the Center.
  And it's right now. It does not seem to go beyond that and I think now that it was all due to the change in the loading screens.

  I even left on overnight assuming the scans took place and it would be frozen until the tests were performed.
  Nothing has changed.

  I tried the obvious; safe mode does not work exactly. I click on it and all I get is the names of the drivers being loaded then a very slow black line through every driver leading one by one.

  Unfortunately, I deleted the backups of my restore system checks an hour before this happened and I did a lot of memory by pressing F8 and choose the option.

  I'd even do a factory reset as long as I've had all my files and drivers on a hard drive.

  I don't know what to do, I am completely distraught. Any advice would be helpful and thanks in advance!
  (a factory reset would be VERY VERY last resort)

  Christian.

  Hello

  as safe mode does not do a start-up repair disc

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  If it does not here's how to save your data

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed!

  and how to reinstall vista

  using dell dvd

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  using the dell recovery partition

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

• Satellite Pro L20 PSL2YE: 1 GB Ram upgrade does not show in the Bios

  I just bought a 1 GB mem stick samsung 4200 s 533 mhz for my L20.
  It does not show in the Bios or in the main menu in Device Manager, but it shows in cpu - z and pz Assistant 2007.

  I am very confused, and upgrade the bios on toshibas website does not include one for the base PSL2YE L20.
  I wonder if all the bios upgrades L20 will work with my machine.

  any help would be great because I am so confused,

  Hello

  If you already have a biosupdate on your machine? It s a bit confusing that you´re confused since I was wondering what do you say with
  "toshibas Web site does not include one for the base PSL2YE L20". Do you mean the bios?

  Please give some feedback.

  P.s.: you can also try this site for a biosupdate:
  http://209.167.114.38/support/download/ln_byModel.asp

  Maybe you will find something.

• Laptop does not connect to the internet. error cannot display Web page

  Original title: laptop does not connect to the internet. How can I fix it?

  I'm trying to get my laptop to connect to internet, but it will not. It keeps telling me that it cannot display the Web page. The wireless connection is the link and he sees the laptop, but it's like he goes. How can I fix it? Help!

  Hello

  1. Have you tried using anythird party web browser to connect to Internet?
  2. You use Internet Explorer to surf the Internet?

  If you receive error message cannot display Web page in Internet Explorer, then you can check the link below to fix the problem.

  "Internet Explorer cannot display the webpage" error when you view a Web site in Internet Explorer

  http://support.Microsoft.com/kb/956196

  Note:

  Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

• I have a problem with my laptop does not connect to the internet. It connects to our wireless very well, but it doesn't have an internet connection.

  I have a problem with my laptop does not connect to the internet. It connects to our wireless very well, but it doesn't have an internet connection. It connects to other networks wifi very well with Internet access, is that the wireless in my house what it connects to. When I diagnose the problem, it says "Cannot communicate with DNS server (208.67.222.222)", and then under that it says: "languished network diagnostics remote hosts, but had not received a response." It connects to the Internet through an ethernet cable, but it is rather annoying pulling the cable autour. I currently have Windows Vista Home Premium. Thank you!

  original title: Internet connectivity problem

  Hello

  Now, you may need to contact the support of Panda Internet Security centre to change the settings so that wireless is enabled through it.

  Support link: http://www.pandasecurity.com/homeusers/support/

• Laptop does not connect to the internet, office. Both use the same router. Tried troubleshooting, does not. Help!

  I have a desktop computer and a laptop. Both use the same router. The laptop does not connect to the network, but the office has no problem. My wireless adapter on the laptop is on, I tried troubleshooting. I tried to turn it off for 30 seconds then restart him. But nothing is resolved the problem. Any ideas would be helpful! Thank you

  Hello

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Reference Dell E6540 - ATI Radeon HD 8790 M does not appear in the BIOS

  Hello

  I have a Dell E6540, which, according to the data sheet must have a graphics card than ATI Radeon HD 8790 M. but looking in the BIOS, there is no entry in addition to the dedicated graphics card Intel 4600.

  I have the latest version of the BIOS and the latest graphics card driver. I am using 8.1 Windows 64 bit.

  Please let me know if I need to do something else to make it the primary video controller.

  Also, is it possible to see if the graphics card is "there"? I think that if it does not show in the BIOS menu, either is missing or broken.

  Any help is appreciated.

  Thank you
  Teo

  There are two ways to create a mobile video hybrid:

  1 hardware control - with a multiplexer equipment

  2 control software, where only the GPU from Intel is hard wired to the display and the secondary GPU is used as a coprocessor.

  Your system is of type 2.  It is not a true independent GPU - this is a coprocessor for the Intel's GPU, fully controlled by software and drivers.  To use the AMD GPU, choose using the Catalyst Control Center under Windows.

  The AMD GPU can never primary rendering on this system: it's a secondary GPU by design.

• My desktop with W7 home premium HP computer does not start beyond the initial screen of HP.

  I had been doing "Master Boot Record error press any key."  for the latest two boots.  Press any key boot the computer and initialized in W7.  But, when I tried to start the computer again, he did not get beyond the initial HP screen with choice... F10, esc, F11, F12, and F9.  By pressing the keys are not going anywhere.  When I pressed ESC, I got "Loading Boot Menu... ', , but does not load the start menu. I tried to boot from a DVD, but the DVD/burner burner did not run.

  When the computer is turned on, the fire HD came a few seconds... .but then nothing.

  Solution?

  Thanks again, Hanspuppa.

  I found the problem.  I removed the CMOS battery and reinstalled.  It seems to work OK now.

• whenever I click on a program, that it does not open and the 'open with' screen appears

  whenever I click on a program, that it does not open and the 'open with' screen appears

  Hello

  Use above message for intense and thorough check for malware.

  To restore the ability to run any .exe programs.

  1 make a Restore Point so that you can come back if necessary back although probably not required.

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  2. copy BETWEEN these lines and paste it into Notepad - save as exefileFix.reg - then right
  Click on it and FUSION - REBOOT

  DO NOT COPY THE LINES
  -----------------------------------------------------------------

  Windows Registry Editor Version 5.00

  [HKEY_CLASSES_ROOT\. [EXE]
  @= "exefile".
  "Content Type"="application/x-msdownload".

  [HKEY_CLASSES_ROOT\. EXE\PersistentHandler]
  @= "{098f2470-bae0-11cd-b579-08002b30bfeb}".

  [HKEY_CLASSES_ROOT\exefile]
  @= "Application".
  "EditFlags" = hex: 38, 07, 00, 00
  "FriendlyTypeName" = hex (2): 40, 00, 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52,------.
  00, 6f, 00, 6f, 00, 74, 00, 25, 00, 5 c, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 33, 00,------.
  32,00, 5 c, 00, 73, 00, 68, 00, 65, 00, 6 c, 00, 6 c, 00, 33, 00, 32, 00, 2nd, 00, 64, 00, 6 c, 00, 6 c,
  00, 2 c, 00, 2d, 00, 31, 00, 30, 00, 00, 31, 35, 00, 36, 00, 00, 00

  [HKEY_CLASSES_ROOT\exefile\DefaultIcon]
  @="%1"

  [HKEY_CLASSES_ROOT\exefile\shell]

  [HKEY_CLASSES_ROOT\exefile\shell\open]
  "EditFlags" = hex: 00, 00, 00, 00

  [HKEY_CLASSES_ROOT\exefile\shell\open\command]
  @="\"%1\" %*"
  ""IsolatedCommand"="\"%1\" %. "

  [HKEY_CLASSES_ROOT\exefile\shell\runas]

  [HKEY_CLASSES_ROOT\exefile\shell\runas\command]
  @="\"%1\" %*"
  ""IsolatedCommand"="\"%1\" %. "

  [HKEY_CLASSES_ROOT\exefile\shellex]

  [HKEY_CLASSES_ROOT\exefile\shellex\DropHandler]
  @= "{86C86720-42A0-1069-A2E8-08002B30309D}".

  [- HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\FileExts\.exe\UserChoice]

  --------------------------------------------------------------
  DO NOT COPY THE LINES

  If necessary:

  Check the fix of exe here
  http://www.Winhelponline.com/articles/105/1/file-association-fixes-for-Windows-Vista.html

  Also check this one if it applies
  http://www.Winhelponline.com/articles/165/1/restore-the-exe-file-association-in-Windows-Vista-after-incorrectly-associating-it-with-another-application.html

  How to set default Associations for a program under Vista
  http://www.Vistax64.com/tutorials/83196-default-programs-program-default-associations.html

  I hope this helps.

• NB200 does not start after the bios - screen black screen with blinking cursor

  Hello

  I was using the laptop as usual when I think there may have been a virus activity - reason I say that is that my anti-virus closed unexpectedly. I couldn't restart programs files.

  I restarted the laptop.

  After the bios menu will I get a blank screen with a blinking cursor - windows does not start.

  I did the following:
  (1) create a USB bootable with Recovery Console window XP - boot with this i can see three drives C:, D: as SDA? I can see the content of these disks, so it seems that my HD works. I ran a fixmbr and fixboot, but this has not solved the problem.
  (2) create a Kaspersky bootable USB virus scan - ran it without problem - he found a few question (not on the disk boot sector) I've fixed.

  An option was to copy files from the laptop and then start it in recovery mode - so Itried to run the phone into recovery mode hold down the 0 key at startup - the bottom of the screen then displays * HDD Recovery mode * and nothing happens.

  Any help - other options would be greatly appreciated.

  My 1 year of that guarantee has expired a few months back so can't send in for repair.

  Thank you

  Hello

  I doubt that it is a virus.
  Seems the file system is damaged on the HARD drive and this is the reason why the laptop does not start until it could also be a partition of HARD disk malfunction.

  Try this; Turn on the unit, press F8, and then check if you have the laptop repair.
  If this is not possible, then you will need to reinstall new OS.

  Here you can order a recovery disc:
  http://backupmedia.Toshiba.EU/landing.aspx
  Of course you will need an external USB CD/DVD drive

• Laptop does not start with the connected usb device

  Hello
  Voila, I have a Sp6100 Pro Satellite, when I try to start whith a usb printer is connected, the laptop does not start. I have the latest version of the bios 1.90.

  THX,
  Barzot @+.

  Hello

  What you mean with start won t at all? Is there any kind of reaction if you press the power button / stop?

• A series of satellite does not start after the BIOS update

  After update bios with the downloaded utility my laptop does not start.
  Do you have this case covered by the warranty?

  I'm not sure if this would be covered by the warranty. You must contact the ASP in your country for details, but I assume that it s not covered.

  PS: Did you try this work around:
  -remove the battery, disconnect the adapter
  -wait ~ 40 min
  -connect the two devices again and try to turn on the laptop

• HP compaq 6510 b does not start after the BIOS update

  Hello

  When I turn on my laptop HP compaq 6510 b it DISPLAYS this message: your bios has not finished updating 6510b.after flashing the bios of the laptop does not start .it displays the same message (your bios did not complete the 6510 b update) and turns off. I cannot access the bios by pressing F10.the bios version was F16 and flash by F20 .will help thank you very much.

  I'll have to return a verdict of laptop motherboard bricked due to a failure of the BIOS upgrade. Sorry, but it happens.

  This means that this would require the replacement of the BIOS chip to make it work again.

• Acer laptop does not start after the blue screen

  After I got a blue screen (flashed by too fast to see the error message) when I try to reboot my acer 5610Z laptop computer with vista home edition, usually nothing happens at all. sometimes windows is trying to run the Startup Repair tool, then crashes and only a cursor flashing at a black screen.  Tried to open the case and clean the Fan & Heatsink heat to air without effect.

  The blue screen came a few days after I started using a new USB mouse, but the fan seemed to get high a few days earlier.

  But I noticed it will make the road to startup repair only if the battery is in, and never if only the power cord is attached.  Also, if I let the computer sit for several days, it is more likely start (even though he never passed from the Startup Repair).

  1. try the system restore.

  2. try to do a startup repair disk.

  3 acer Recovery Options.

  4. contact Acer.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  See you soon.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, try to make a Bootable ERD to do a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the link provided and make a bootdisk of it.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.acerpanam.com/Synapse/forms/portal20.cfm?RecordID=853&formid=3390&website=AcerPanAm.com&siteid=7117&words=all&keywords=&areaid=2

  Acer eRecovery made

   

  1. on the Acer splash screen, you can press Alt and F10 (at the same time press F2 to enter the BIOS) to make it appear a version BACK style eRecovery.

  ·        The unit is able to reload Windows from this mode faster then CD.

  ·        The default password is 000000 (6 zeros) and it is shown when you are prompted for the password.

  ·        Users are able to change the password in this mode for eRecovery only.

  ·        The system can retrieve the hidden on the hard disk (partition PQService) image or a CD/DVD media.

  ·        It is possible to reload the factory CD/DVD style or snapshots that creates the eRecovery Windows version.

  2. in Windows, there are 3 ways to access eRecovery functionality.

  ·        Press Alt and F10

  ·        Open Acer eManager and then double-click eRecovery.

  ·        When a system is new it should automatically open this application and invite you to do the recovery media.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.Acer.com/worldwide/support/index.htm

  Support &

  See you soon.

  Mick Murphy - Microsoft partner