laptop HP smarttouch: Please help forgot password of bios off #67512837 system

Similar Questions

• HP G62 Bios 52991539 please help administrator password system

  HP G62 Bios 52991539 please help administrator password system

  @mal6

  Enter 43699519

  Kind regards

  DP - K

• Please, help to recover the BIOS on the dv7-4120er (xe276ea)

  Please, help to recover the BIOS on the dv7-4120er (xe276ea).

  I updated my BIOS, but now the screen is off.

  I have no HP_TOOLS of recovery on the HARD drive partition and I did not backup usb with BIOS.

  How can I recover my BIOS?

  Please help me.

  Please see HP Notebook PC - Restore the BIOS, which States that you may be able to create a 'USB key with a HP_TOOLS volume' to Flash the BIOS. Please see http://h30434.www3.hp.com/t5/Other-Notebook-PC-Questions/How-to-use-the-HP-BIOS-update-uefi-utility/... for step by step instructions that can be used to create the 'USB key with a HP_TOOLS volume '. You may be able to skip 'step 4 '. Please see the HP Pavilion dv7-4120er Entertainment Notebook PC drivers page for the appropriate download needed for this procedure.

  Updated HP Notebook System BIOS (Intel processors)

  HP System Diagnostics UEFI

  HP Unified Extensible Firmware Interface (UEFI) support environment

  HP update BIOS UEFI

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• HP envy m6 1105dx: Please help admin password required

  Required administrator password. entered the wrong code 3 times and now showing a code: 59587632. Please help the laptop is a hp envy m6 1105dx. Thank you

  Hello

  Enter: 46485214

  Kind regards

  DP - K

• HP paviilion 15 laptop: screen brightness please help ASAP

  Hi guys, my display brightness is not adapt a day ago not used for theres no etc system restore and when I press f2 or f3 theres no increase or decrease it please help im really in urgent need all my software are average date until

  Hi @DylanL,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your 15 HP Pavilion Notebook and brightness does not properly. I see that if you change the balanced power plan options option in the book will help. Here is a link that will help you. Go to your power options.
  Select balance, then click on change plan settings. Click on change advanced power settings. Then save changes. Sometimes just changing and selecting apply it and change it back solves this problem.

  You can try to use the Windows Update Troubleshooter to fix updates that do not come through Windows 8.  Please restart the laptop twice to make sure that all updates are completed!

  You can also try:

  In Device Manager, click the arrow next to display adapters to expand this category
  Right-click on the graph, and then select Update driver software if more than 1 graphic adapter do 1 at a time.
  Select search automatically for updated driver software.

  The laptop must find and automatically install the updated driver
  Once the installation is complete, restart your laptop.

  Please let me know how it goes.

  Thank you.

• Laptop HP 2000: Please help with code

  I have a hp and asked power on password or password administartion. The disabled system code is 55614723

  Try entering the following unlock code:

  40772305

• I have a fatal error of the system on vista (Home Basic). Please help, it is said: __STOP: C000021a {fatal system error} initial session process or system _ ended unexpectedly with status 0x00000000 (0 xC0000001 0 X 00100450)

  That's what happened, I was using just disk defragment hard disk and since it takes a long time, I just left it alone and came to my laptop after a few minutes (about 15 minutes) and all of a sudden, I see my laptop is off.
  I turn it on again normally and after a while, the screen goes black and a blue screen with the message above appears. I press the "TURN OFF" button and it shuts down.
  That's the problem.

  I can not use safe mode or something, I tried everything in the F8 menu such as 'Last good known Configuration (Advanced)' and 'debugging '. Nothing works, all of this brings back me to the error message.

  The only thing I can do, is use the Startup Repair tool.

  It scans and tells me that he could correct errors, then I used the restoration of the system (to an earlier point), I haf 2 restore points but an error message appears and then they both became deleted. At the moment, I have no restore points.
  I can only use the command line Interface which directs me to "x: windows\system32\.

  I can use regedit (the registry editor). However, I tried another procedure step by step that earlier, I found that told me how to fix this problem, I typed in "System Root\System32\Drwtsn32.exe" and it says 'system is not recognized as an internal.... " »
  I also tried "System32\Drwtsn.exe" and he said: 'the path cannot be specified.
  I don't know what to do, I ask you is can you please help solve me this problem by using CMD and the registry editor. Please, thank you very much for your time.

  ADDITIONAL INFORMATION:
  My laptop...
  Windows Vista Home Basic
  1.00 GB of RAM
  AMD Athlon processor
  120 GB hard drive
  ATI Radeon X 1250 graphics card (that I could remember)

  It's strange, so you are always able to get into the safe mode command prompt is that correct? If so try to type sfc/scannow and see if it finds problems

  regarding the komodia, you can stop this cycle by quickly tapping F8 and select Disable automatic reboot after the system failuyre you should give the sfc/scannow suddenly too who could fix

  Oh and the reason for which you've entered in this thing drwtsn.exe and itt said it does not recognized is because you're not on the right track

  in any case I doubt that may help, but if you know you need to learn how to navigate your system using the command-line... pretty easy:

  CD means change directory

  If you type cd-it will take you to the root of the system

  so go ahead and type of

  Note that you are no longer in the c:\windows\system32 folder

  now type
  CD windows
  CD system32
  Drwtsn32

  Note that you can type the first few letters of a file or folder tab and press on to fill in the rest

  in any case, who should start the program that you try to start but I think that your better off trying to run the sfc/scannow command. Let me know how you go

• "operations are underway. Please wait. The machine switches off automatically '-system never stops.

  Sometimes, when to stop Vista, instead of a normal shutdown, I get quite common background and a message reading: "operations are underway. Please wait. The machine switches off automatically. "The system then continues to run indefinitely, and I finally have to do an emergency stop. After the reboot, I then most of the time have to do a restore to an earlier point; Once in a great while, he'll tell me the test stops abnormally and charge really. Tried to figure what could be causing it and can't find a logical reason. Diagnosis never found anything, but there is not really anything in the windows which diagnosed something as a shutdown of the system.  Help.  It's boring.

  Hi Baron Stewart,

  (1) since when are you facing this problem?

  (2) remember to make changes?

  Method 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...)  Except the mouse and keyboard and then try to stop

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Method 2:  Select the boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  
  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  Method 3: check the logs in Event Viewer for more information on this problem

  Open event viewer

  What are the information in event logs? (Event Viewer)

• Compaq 21-n001ar: Please help I need the bios password

  Please I need your help, my laptop shows the following message when I press F2 at startup:

  Password/unlock key: _

  Indicator release key number: D515D73C

  I don't know what my unlock key is... is it possible to reset it, or you can provide it to me? I saw an another messages when this happens, is it not possible with my laptop model?

  Thank you!!

  Hello

  Your laptop is to produce a code hexadecimal halt which is stored in the ram as a 'one stop' and is recalculated after a reboot.  This indicates that you have a FRIEND bios later and unfortunately none of the current code generators will work - surprisingly, you can always remove power on password of the machine by removing the cell RTC (leave the connected Power Board) then hold down the power button for 60 seconds before reinserting the RTC.

  The bad news is that the RTC is usually on the 'wrong' side of the system board, so it will take a lot of disassembly.

  Kind regards

  DP - K

• Please help Admin password

  on my wifes laptop, I set an admin password so I could limit were the children go.  as an indication of password I just typed the password so that I wouldn't forget.   My norton has expired and I can't load, because my password does not work. Any help would be greatly appreciated Hank21629

  There are a lot of options built into Windows to help you out of this situation:
  • Restart the computer with your Windows repair CD, then use system restore to set Windows to a point before your wife the password.
  • Log on to your account admin to spare, and then reset the password for your existing account (works only if you set up an alternative admin account).
  • Log in as administrator mode without failure, then reset the password for your existing account (the password is usually empty).
  • Insert your flash drive USB with the password key file (only works if you have taken the time to create such a key file).
  • Use the password indicator (works only if you have created a hint and if it's good enough to allow you to guess the password)
  • Check your paper files (works only if you threw down the password somewhere)

• My laptop is compatible (please help)

  So there's a new GeForce GTX 850 M update (it's the 361.75 version) and I have a Dell Inspiron 14 7447 (7000 series).

  I asked people to Nvidia if I install this, it's what they say expressly:

  'http://us.download.nvidia.com/Windows/361.75/361.75-win10-win8-win7-winvista-desktop-release-notes.pdf '.

  Always check the notes version ;)

  For the stability and the "optimal" performance you should ONLY use driver package recommended by the manufacturer.

  You have a portable computer... you should not try to "update", the driver or the operating system except if it is found on the site of the manufacturer under your exact model #. In fact; with some units if you RAM of the laptop to a service center the RAM would be refused because the driver/OS software that has not been listed is used (ie: the device is used outside the manufacturer's specifications). »

  So, in short, they told me that I have to go here and ask if my cell phone is compatible with the new GTX 850 M updated? I don't know how to find if my laptop is in the compatible list... Need help D:

  THX guys

  

  Please click the link below for your Support page of Dell - Inspiron 14 7447, 10 windows, 64 bit);

  www.Dell.com/.../drivers

  

• Computer HP laptop problem. Please help someone!

  Hi guys,.

  So basically, my computer HP laptop froze about three times today. I had to press the button reset each time. Finally, the computer came back the menu but has frozen immediately. I pressed the reset button again. This time, when I turn on the laptop the first thing that appears is the HP Logo and the "resumption of system preparation. After a while the screen goes white and after a while once again the HP logo comes again, but this time is not written and just a loop that goes round in circles. Nothing happens after that. I tried it turn on and shut off again, but the same thing happens.

  Does anyone know how can I fix? It seems that you must press F11 when you turn it on and go through a few options to make it work again? I have some pictures and music on there I'd like to keep, can I do this? Or do I need to clean the system? There not too important! Little help would be great if someone can give me some adivice on how to fix it!

  Thank you very much

  Hi Cammy, I'm back

  Press the ESC key at startup then F2 when the Start Menu is displayed, this will start the System Diagnostics, advise me the results.

  Redemarrer restart using the ESC for the Start Menu button, press the F11 key to the restoration of the system, do not press any other button unless he asks you to do.  Let it run for 15 minutes to see if any other measurement of the recovery process.

• EMERGENCY SITUATION! Please help me! Why the OFF button would not start me in the hp recovery partition?

  I bought a hp Pavilion dm4-2015dx for a little more than a week or two to Bestbuy.ca.

  When I tried to launch the recovery by pressing F11at the start this morning, the following is the display.

  Windows could not start. A recent hardware or software change might be the cause...

  file:\Boot\BCD

  Statue: 0cx0000225

  Info: an error occurred trying to read the boot configuration

  Note: I recently made a partition, I divided the C drives in A and B, I wonder if that has an effect on my computer?

  Help, please! Only, I bought the laptop for a little more than a week

  Greetings,

  If you insert the first disc in your DVD-rom and you start your computer, the screen HP press ESC until you get a menu. Select the start menu and select CD/DVD-ROM, then enter. When it tells you to press a key to boot from the CD, press a key any. This will load the recovery software. Select immediate assistance and a recovery of the system. This will install your computer as the day where you bought everything first.

  WARNING * you will lose all files and programs that you have installed and placed on your computer that you bought the device.

  Yes, this will allow you to use the F11 key again once the recovery complete. Typical HP for the device warranty is one year. We can find this information for you. If you look at your serial number label, it should give you a serial number and the identification code of the product. With this information, you should be able to trace accurate information by the auditor of warranty status if your product has a #ABA or something similar, don't forget that.

  To find your sticker:

  http://h10025.www1.HP.com/ewfrf/wc/findModel?cc=us & DLC = in & LC =

  The guarantee verification link HP is:

  http://h10025.www1.HP.com/ewfrf/wc/weInput?cc=us & DLC = in & LC = on & os = 4062 & Product = 3204464 & softwareitem = MP-74848-1 & sw_lang =

• Please help, the printer does not have 'ink system failure '.

  Hello

  Any help appreciated.  My printer is printer all-in-one Photosmart C7280.

  2 days ago my printer has not worked. It comes with several error messages after I turn it on. The first is "ink system failure: ink system has failed." Cannot copy, receive faxes or print. Refer to the printer documentation. Error: 0xc19a0025. Turn off the power, then new. »

  However when I turn off and then again via the "power" button, I get a message saying "abnormal termination. Then the same error message original returns (0xc19a0025). It is the most common error and won't go away. Then too, I get a message saying "problem Photo tray: lift the output tray, check the photo tray is pushed up to the stop, lower output tray. Despite the fact that I haven't used the photo tray in several months and it is in the correct position.

  So far I tried to turn on the printer, shut down several times by using the power button. Also, I turned off the printer in making last night (after having been closed properly) and back on this morning. I looked through the documentation of the printer, but could not find tips for troubleshooting for this kind of problem. I updated the driver from HP using software update on my mac, and the problem is still there.

  Now I get desperate, I rely on my printer/scanner/copier a lot!

  Thank you

  Nathalie

  This widget could not be displayed.

• Pavilion g6 1260ec: password forgotten BIOS - off System (69900575)

  Hi, I forgot my BIOS admin password.

  Laptop HP Pavilion g6-1260ec
  Windows 7 (64 bit) operating system
  Disabled system "69900575".

  Sorry for my bad English

  Thanks in advance
  Best.

  @Yen22

  Enter 76668571