LaserJet pro 400 m425: laserjet pro 400 m425 does not start

Similar Questions

• Satellie Pro A60 EN does not start

  My satellite Pro A60EN does not start. When I turn on the power there is a slight click, but it does not read the disk. If I boot with a bootable CD, it starts the CD/DVD drive, but does not start. The HARD drive is OK, as I tried it on my desktop (using an IDE USB connnector).
  East - the CPU, motherboard or RAM?
  Any help much appreciated.

  Hello

  To find out what s wrong some diagnostic tests are needed.
  If you checked the HARD drive and if it s ok so I guess there must be something wrong with the motherboard. But it is worth checking to be sure 100%.
  The fact is that the motherboard is an expensive piece and you should check it out before you replace something.
  Sorry I put t see any other solution.

• Satellite Pro M10 PS630E does not start after upgrading CPU

  I tried to install a new processor for my Toshiba Satellite Pro M10-PS630E.
  He initially has a 1500, I tried to put a 1766.

  I follow the maintenance manual, later the computer change is not star upward.
  When I connet to power it show that the luminous power of orange/amber color and make 5 flashes, then 3 and then restart blinking.

  My question is "is it posible to do a reset of the bios parametrers" or "reset the CMOS?
  Is it possible to get it working again.

  Hello

  The flashing light means that it has detected a hardware problem on the motherboard!
  Perhaps you have used a wrong CPU and is not compatible.

  Perhaps the BIOS does not support this processor and therefore this flashing error code appears.

  What say you can't update the BIOS! First of all, that's not possible since only focused on the victory of BIOS is available for download. You must run the Windows operating system to update the BIOS.
  Secondly the update of the BIOS won't help you with this problem!

  You must use a CPU that is fully compatible!

  Welcome them

• Satellite Pro M70-113 does not start up - it hangs at the logo screen

  Hello

  I have a toshiba satellite pro m70-113.

  Sometimes when my laptop turns off mode standby automatically, due to inactivity and then if I press a key on the keyboard to wake up nothing happens and I have no other choice but to it stop completely by pressing the button for 5 seconds.
  But when I restart it works well, that is to say, it starts very well.

  But today, when it is in a similar situation, I restarted the laptop, the screen move after the logo screen toshiba. I have the power on several times, but without success. It crashes just on screen toshiba logo.

  After a few restart I pressed ESC while restarting and the toshiba logo changed to the texts POST bios screen.
  And I found that the text will not go forward after having reached:
  Find disk 0:
  Maybe default feel HDD initialization...
  The captured image is here:
  http://img144.imageshack.us/img144/9986/image007sp2.jpg

  Note: this is a capture when, I don't know how the system has just begun works very well and can be seen that the HARD drive is detected normally this time. While the earlier version, it will not proceed after having reached "Found Disk 0:

  So, the problem is that at the time of the problem, the hard drive was not read / initialized or something like that.

  And I remember that when I tried to reboot my laptop and it did not work. It was running on battery and when I switched power supply that worked.

  So it is a problem that has been fixed in a bet to update BIOS, but for another laptop (see laufendspass post) his link on this forum is here:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13143&MessageID=48143

  And my current bios version is 1.1 and an update is available for v1.30... (But I have not yet updated)

  Another problem I had met some time was same this post mentions to be corrected during the update of the bios.
  i.e. "corrected: a computer that is turned on to State power and running on battery power, may crash if the user is connected to the AC adapter while it is start.»

  So, for this, all mean that these problems can be solved by an update of the bios v1.30 which is available for my Satellite m70-113?

  Please answer.

  Hi Ashish,

  The fact that the initial POST process cannot access your hard disk suggests you that there is a possible problem with the drive, maybe he is not in place correctly when power is applied to it. The contents of the disc should be OK, then I suggest you take a good backup of your system (or at least your personal data) If you manage to get your notebook to boot successfully.

  I do not think that an update of the BIOS will affect any on that since the problem does not seem to have a certain 'trigger', and if the BIOS cannot access the hard disk then no matter what version of BIOS you are using.

  Kind regards

• Satellite Pro L300-1FN does not start - hang at the BIOS splash screen

  My Satellite Pro L300-1FN refuses to start. When turned on the laptop displays the home screen toshiba/insyde H20 BIOS and the message "press F2 go to the Setup utility, F12 to go to the start menu" and flashes the light access to the hard drive, but don't try to continue loading. I left the bios at the start screen, but it doesn't do anything for long hours on a power supply or is running the battery flat while on battery.

  Is there a way to re - put the BIOS on this unit? If it's a desktop unit I would remove the CMOS battery to force a reset of the BIOS but that's impossible on a laptop. The hard drive is fine because I have it plugged into another system to remove valuable data.

  Hello

  What happens if you press F2 when starting the laptop to the top?
  You can access the BIOS?
  If so, access the BIOS and set its default value. I think you need to press F9 or F10 to get default parameters, but this will be mentioned at the bottom of the page of the BIOS.

  Check it!

• Mackbook Pro ME664LE/A does not start - only fan comes on

  MBP ME664LE/A - A1398 (EMC 2673). MacBook Pro Core i7 2.4 15 "beginning 2013.

  During an Office Update, the MBP began to operate the fan periodically. The MBP was not hot. After a while her display off (black) and the MBP has failed.

  Whenever I want to turn it on, only the fan turns on.  I followed all the procedures to get back to zero and also SMC reset, but nothing change.

  Any Suggestions? Could be a known problem?  Someone in the the Argentina Macusergroup said that apparently a known issue related to the card mother apple in 2013 models...

  The MBP has little use, only a few weekend for personal staff... I am concerned, I spent a lot of money in this MBP to get the best laptop at home, and it's a failure...

  Connect the MBP to a monitor.  If the monitor does not display an image, the main suspect is a faulty GPU.  If the monitor displays an image, the display or the connection to the screen is defective.

  Ciao.

• I am trying to download a free trial of first pro, but it does not start the download.

  Hi, having some problems the trial download. What is creative cloud that does not?

  Hello

  Please see the system requirements for pro first: -.

  System requirements | Adobe Premiere Pro

• Satellite Pro A100-080 does not start - stays dark after 3 beeps

  Hello
  After a week off, the Toshiba Satellite Pro A100-080 (PSAASE-00G004GR, 4 GB RAM) of my kids start not anymore.
  When turn on/off the system, he * will beep 3 times * (one long, two short beeps), the HDisk light flashes 'blue' and then nothing more. A/c and battery power LED are 'blue', which seem to be OK status.
  No other useful help, as the screen remains dark.

  We had upgraded to 4 GB MEM (Kingston) a year ago and I already tried the old used 1 GB (included with purchase) or the replacement of 2 x 1 GB since December 2007, but equal status with these modules. This is not
  a defect of memory.

  I hope that this is not the motherboard, probably only the NVIDIA GeForce Go 7600 graphics included adapter?
  Does anyone have an idea what could be the problem?

  Thx for a short help.

  Hello

  Generally this type of beep codes are hardware related or with other words, hardware is defective. So I think it's a hardware problem and an ASP must check your laptop computer to identify the cause of this.

  On the Toshiba site, you will find a list of aspic:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

• Satellite Pro A120 (PSAC0E) does not start after upgrading RAM

  Hello

  I hope someone can help me here, I recently bought a Satellite Pro A120 (PSAC0E) and decided to upgrade the RAM. I bought a stick of 512 MB of curries with the following specifications: DDR PC2700 200-pin 333 Mhz SODIMM (64 x 64).

  However, the first problem I encountered was an alignment problem. A little effort and handling solved this, but after you insert the RAM into the available slot, the computer laptop wouldn't boot, and instead, I had the flashing sequence on the LED from 2,3,3.

  I was told it might be a problem matching, then tried to remove the original RAM and booting with just the new stick, still the same error. I tried it in the slots and still no joy. It starts very well with the original 256 MB of RAM, but refuses to take the new RAM.

  Are there any known issues? Can anyone suggest something that I can do wrong? I followed the usual steps of upgrade to remove all power cables and the battery before the upgrade, but still no joy.

  Hoping that someone is able to help!

  Hi James

  You simply have bad memory modules and is not a compatible uses.

  > the first problem I encountered was an alignment problem. A little effort and handling solved this,

  This should not happen! The right modules can be inserted without any problem of alignment!
  Handling can damage the module!

  In my opinion, you should use another and supported the RAM module.

  To my knowledge, you can use the PA3512U-1M1G (DDR2-667 1 GB Memory Kit) or (PA3411U-2M1G) DDR2-533 1 GB
  The two should be compatible.

• After installing windows XP Pro my computer does not start correctly

  After you have installed Windows XP Pro on my HP Pavilion (updated to XP home), my computer will not end the restart process.  I have repeatedly in a loop once the blue screen with the HP logo.  When this has happened before after installing a pack of updates for XP Home, we just started in safe mode and then had it will restart at an earlier time, thus eliminating the updates.  However, now when I try to start in safe mode, I get an error message that says: "Windows Setup cannot start in safe mode" and I leave safe mode.  We hoped that by installing Windows XP Pro, this problem should go away.  Can anyone help?  I have read several other entries in the forum for similar problems, but they all have to do with updates.  This is the first time I was not able to use safe mode, so now I'm stuck.  I hope that I can avoid having to perform a full system recovery, since it is a long involved process and having once before, I always felt the same restart problems after installing updates.

  PA bear,

  Thank you for help... After reading several posts in the forum, one of them reminded people to check with the manufacturer of the computer so that possible solutions... and this is the solution here, I wish I thought of him earlier... I did a system recovery to remove the Windows HP Pro and return to the original version of the default value.  Then I went to the HP site and downloaded the patch according to their directions.  Problems fixed! :-)

  Any PERSON HAVING HARD REBOOT YOUR HP PAVILION (with an AMD processor) after you install Windows XP service pack 2 or 3 updates:

  HP has a patch that solved all my problems.  Clearly, service packs contain information for Intel processors that is in conflict with AMD processors in many HP Pavilion desktop computers.  You can go to their customer service solutions website and download the patch.  Since I did it, I had no other problems. I wish just that I had discovered the solution until I had to do a full system recovery.

  If your computer hangs on reboot 'loop', see if this info. HP will help you:

  The computer restarts after a Stop error message display 0x0000007E (after update with Service Pack 3 for Windows XP)

  If you have had problems with XP updates, including service pack 2 or 3, try this page:

  Before you install Windows XP service pack 3

  Please pass on to other similar issues.

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• Satellite Pro U400 - WXP does not start & cannot run recovery is

  Help please!

  I tried running the recovery disc using the F12 key, I kept getting WARNING 'this HARD drive is not initialized' - initialize HARD drive & restart. are you sure you want to continue? I clicked on Yes-error F3e1000001 (HDD not not found) - I clicked on none he turned off the computer!

  I tried a different way by pressing the 0 im power on, because then I can no longer load window XP, it automatically runs 'Virtual disk Image', then by loading the tool recovery & followed the same HDD warning is not initialized & etc. and then eventually turn off the laptop itself!

  Please help if you can! Thank you!

  Hello

  I guess that your HARD drive is defective.
  The HARD drive is recognized in the BIOS?

  If this is not the case, replace the HARD drive and then try the recovery disk.

• Satellite Pro L650/L650D does not start

  My laptop Toshiba does not work...

  When he was for a restart, the it closed suddenly... I want to start (start), but when I clicked on the Start button, it does not start... The LED lights were lit, but the laptop does not start...
  At the present time, the lights went out, I don't know how...

  It means that the laptop is break down?
  I hope not, because I don't want to spend more money with that... :(

  Is there someone who could solve this problem?

  Thank you very much, long in advance,
  Raquel

  It is not easy to solve these questions, because nobody knows what is the problem. It may be BIOS related issue or some other hardware related issue.
  It's that there are not a lot of options in this regard.

  You can try to remove the battery and unplug the power supply, press the power button / stop for a while and try again with power running. The same thing happens again?

  > The lights were on, but the laptop does not start...
  You hear cooling ventilation? When the laptop is turned ON it turns off a few seconds later or stays, but without any reaction simply?

• Sat Pro L10: WXP does not start correctly

  With a few computer startup problems. Screen loads but does not load the widows "xp" logo. So, I went with a balnk screen and no computer activity. Can you help me?
  S

  Hello!

  It can be:
  1. some Windows XP system files are damaged (it looks like explorer.exe)
  2. the machine has probably a virus.

  Suggestion: it is possible to reinstall OS (Windows XP)

• Satellite Pro C660-v10 does not start: pxe - e61 media test failure

  Hello

  laptop was dropped accidentally, worked very well at the beginning but now does not.
  Press f12 for the boot menu, the screen says,

  PXE - e61 media test failure - check the cable.
  PXE - m0f too; output
  PXE rom operating system not found. Please can someone explain what this means?

  > pxe - e61 media test failure - check the cable.
  > pxe - m0f; output
  > pxe rom, system of operation not found.
  > can someone please explain what this means

  Hello

  The PXE error in most cases because the laptop can not boot from a CD-DVD or HARD disk drive and going to the LAN.

  There's maybe one losing a contact between the HARD drive and controller HARD drive.

  Select this check box. Open the HARD drive Bay and check if the HARD drive is properly connected.

  If the HARD drive would not be recognized even if the connection is OK, then I would say that your HARD drive is defective and must be replaced.